Currently, IPoIB is an LLTX driver that uses its own IRQ-disabling
tx_lock. Not only do we want to get rid of LLTX, this actually causes
problems because of the skb_orphan() done with this tx_lock held: some
skb destructors expect to be run with interrupts enabled.
The simplest fix for this is to get rid of the driver-private tx_lock
and stop using LLTX. We kill off priv->tx_lock and use
netif_tx_lock[_bh]() instead; the patch to do this is a tiny bit
tricky because we need to update places that take priv->lock inside
the tx_lock to disable IRQs, rather than relying on tx_lock having
already disabled IRQs.
Also, there are a couple of places where we need to disable BHs to
make sure we have a consistent context to call netif_tx_lock() (since
we no longer can use _irqsave() variants), and we also have to change
ipoib_send_comp_handler() to call drain_tx_cq() through a timer rather
than directly, because ipoib_send_comp_handler() runs in interrupt
context and drain_tx_cq() must run in BH context so it can call
netif_tx_lock().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Back in prehistoric (pre-git!) days, the kernel's MSI-X support did
request_mem_region() on a device's MSI-X tables, which meant that a
driver that enabled MSI-X couldn't use pci_request_regions() (since
that would clash with the PCI layer's MSI-X request).
However, that was removed (by me!) years ago, so mthca can just use
pci_request_regions() and pci_release_regions() instead of its own
much more complicated code that avoids requesting the MSI-X tables.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Handle the case where posting a send is requested when the link is
down. This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1117>.
Signed-off-by: Yannick Cote <yannick.cote@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") changed how paths are flushed on an SM event. This
change introduces a problem if the path record query triggered by
fails, causing path->ah to become NULL. A later successful path query
will then trigger WARN_ON() in path_rec_completion(), and crash
because path->ah has already been freed, so the ipoib_put_ah() inside
the lock in path_rec_completion() may actually drop the last reference
(contrary to the comment that claims this is safe).
Fix this by updating path->ah and freeing old_ah only when the path
record query is successful. This prevents the neighbour AH and that
path AH from getting out of sync.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1194>
Reported-by: Rabah Salem <ravah@mellanox.com>
Debugged-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A break after a return serves no purpose, remove it.
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes the problem of incoming BMA responses being dropped due to
a bad "is response" check. Fix the test to use the ib_response_mad()
predicate, which correctly handles BMA MADs.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=988>.
Signed-off-by: Michael Brooks <michael.brooks@qlogic.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to set the source LID in the sent LRH was not setting the low
bits if LMC != 0 for RC/UC QPs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a QP goes into error state, it is required that CQ entries with a
flush error status are delivered to the application for any
outstanding work requests. eHCA does not do this in hardware, so this
patch adds software flush CQE generation to the ehca driver.
Whenever a QP gets into error state, it is added to the QP error list
of its respective CQ. If the error QP list of a CQ is not empty,
poll_cq() generates flush CQEs before polling the actual CQ.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix deadlock on RTNL between bcast join comp and ipoib_stop()
RDMA/nes: Fix client side QP destroy
IB/mlx4: Fix up fast register page list format
mlx4_core: Set RAE and init mtt_sz field in FRMR MPT entries
Taking rtnl_lock in ipoib_mcast_join_complete() causes a deadlock with
ipoib_stop(). We avoid it by scheduling the piece of code that takes
the lock on ipoib_workqueue instead of executing it directly. This
works because we only flush the ipoib_workqueue with the RTNL not held.
The deadlock happens because ipoib_stop() calls ipoib_ib_dev_down()
which calls ipoib_mcast_dev_flush(), which calls ipoib_mcast_free(),
which calls ipoib_mcast_leave(). The latter calls
ib_sa_free_multicast(), and this waits until the multicast completion
handler finishes. This handler is ipoib_mcast_join_complete(), which
waits for the rtnl_lock(), which was already taken by ipoib_stop().
This bug was introduced in commit a77a57a1 ("IPoIB: Fix deadlock on
RTNL in ipoib_stop()").
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix QP not being destroyed properly on the client, which leads to
userspace programs hanging on exit. This is a missing chunk from the
connection management rewrite in commit 6492cdf3 ("RDMA/nes: CM
connection setup/teardown rework").
Signed-off-by: Faisal Latif <flatif@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Byte swap the addresses in the page list for fast register work requests
to big endian to match what the HCA expectx. Also, the addresses must
have the "present" bit set so that the HCA knows it can access them.
Otherwise the HCA will fault the first time it accesses the memory
region.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Initialize the L_Key and R_Key for memory regions returned from
mlx4_ib_alloc_fast_reg_mr(). Otherwise callers just get garbage for
the memory keys and can't do anything useful with these MRs.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c8c2afe3 ("IPoIB: Use rtnl lock/unlock when changing device
flags") added a call to rtnl_lock() in ipoib_mcast_join_task(), which
is run from the ipoib_workqueue. However, ipoib_stop() (which is run
inside rtnl_lock()) flushes this workqueue, which leads to a deadlock
if the join task is pending.
Fix this by simply not flushing the workqueue from ipoib_stop(). It
turns out that we really don't care about workqueue tasks running
during or after ipoib_stop(), as long as we make sure to flush the
workqueue before unregistering a netdev.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1114>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The check for max physical address was incorrect, thus limiting the
range of allowed physical addresses.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a UD QP has some work requests queued to be sent by the DMA engine
followed by a local loopback work request, we have to wait for the
previous work requests to finish or the completion for the local
loopback work request would be generated out of order. The problem
was that the work request queue pointer was already updated so that
the request would not be processed when the DMA queue drained.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Under rare circumstances, the ehca hardware might erroneously generate
two CQEs for the same WQE, which is not compliant to the IB spec and
will cause unpredictable errors like memory being freed twice. To
avoid this problem, the driver needs to detect the second CQE and
discard it.
For this purpose, introduce an array holding as many elements as the
SQ of the QP, called sq_map. Each sq_map entry stores a "reported"
flag for one WQE in the SQ. When a work request is posted to the SQ,
the respective "reported" flag is set to zero. After the arrival of a
CQE, the flag is set to 1, which allows to detect the occurence of a
second CQE.
The mapping between WQE / CQE and the corresponding sq_map element is
implemented by replacing the lowest 16 Bits of the wr_id with the
index in the queue map. The original 16 Bits are stored in the sq_map
entry and are restored when the CQE is passed to the application.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The idr_find() function may fail when trying to get the QP that is
associated with a CQE, e.g. when a QP has been destroyed between the
generation of a CQE and the poll request for it. In consequence, the
return value of idr_find() must be checked and the CQE must be
discarded when the QP cannot be found.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the ehca driver detects an invalid opcode in a CQE, it currently
passes the CQE to the application and returns with success. This patch
changes the CQE handling to discard CQEs with invalid opcodes and to
continue reading the next CQE from the CQ.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rename the "poll_cq_one_read_cqe" goto label to what it actually does,
namely "repoll".
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since the introduction of the port auto-detect mode for ehca, calls to
modify_qp() may be cached in the device driver when the ports are not
activated yet. When a modify_qp() call is cached, the qp state remains
untouched until the port is activated, which will leave the qp in the
reset state. In the reset state, however, it is not allowed to post SQ
WQEs, which confuses applications like ib_mad.
The solution for this problem is to immediately set the qp state as
requested by modify_qp(), even when the call is cached.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are users that are running UDP applications that require a large
receive queue size in order to get good performance. To prevent
allocation failures for rx_rings when using non-SRQ mode and large
recv_queue_size (1K or larger), use vmalloc() instead of kcalloc() to
alocate rx_rings.
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mad: Test ib_create_send_mad() return with IS_ERR(), not == NULL
IB/mlx4: Allow 4K messages for UD QPs
mlx4_core: Add ethernet fields to CQE struct
IB/ipath: Fix printk format warnings
RDMA/cxgb3: Fix deadlock initializing iw_cxgb3 device
RDMA/cxgb3: Fix up MW access rights
RDMA/cxgb3: Fix QP capabilities
RDMA/cma: Remove padding arrays by using struct sockaddr_storage
IB/ipath: Use unsigned long for irq flags
IPoIB/cm: Set correct SG list in ipoib_cm_init_rx_wr()
In case of error, the function ib_create_send_mad() returns an ERR
pointer, but never returns a NULL pointer. So testing the return
value for error should be done with IS_ERR, not by comparing with
NULL.
A simplified version of the semantic patch that makes this change is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@correct_null_test@
expression x,E;
statement S1, S2;
@@
x = ib_create_send_mad(...)
<... when != x = E
if (
(
- x@p2 != NULL
+ ! IS_ERR ( x )
|
- x@p2 == NULL
+ IS_ERR( x )
)
)
S1
else S2
...>
? x = E;
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Current code limits the max message size to 2K for UD QPs, while MTU
might be as big as 4K. This patch sets the maximum message size to
4K, which is needed for UD to work correctly on fabrics with a 4K MTU.
Signed-off-by: Alex Naslednikov <xalex@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add ethernet-related fields to struct mlx4_cqe so that the mlx4_en
ethernet NIC driver can share the same definition.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_driver.c:1260: warning: format '%Lx' expects type 'long long unsigned int', but argument 6 has type 'long unsigned int'
ipath_driver.c:1459: warning: format '%Lx' expects type 'long long unsigned int', but argument 4 has type 'u64'
ipath_intr.c:358: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'u64'
ipath_intr.c:358: warning: format '%Lu' expects type 'long long unsigned int', but argument 6 has type 'u64'
ipath_intr.c:1119: warning: format '%Lx' expects type 'long long unsigned int', but argument 5 has type 'u64'
ipath_intr.c:1119: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'u64'
ipath_intr.c:1123: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'u64'
ipath_intr.c:1130: warning: format '%Lx' expects type 'long long unsigned int', but argument 4 has type 'u64'
ipath_iba7220.c:1032: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
ipath_iba7220.c:1045: warning: format '%llX' expects type 'long long unsigned int', but argument 3 has type 'u64'
ipath_iba7220.c:2506: warning: format '%Lu' expects type 'long long unsigned int', but argument 4 has type 'u64'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Running 'ifconfig up' on the cxgb3 interface with iw_cxgb3 loaded
causes a deadlock. The rtnl lock is already held in this path. The
function fw_supports_fastreg() was introduced in 2.6.27 to
conditionally set the IB_DEVICE_MEM_MGT_EXTENSIONS bit iff the
firmware was at 7.0 or greater, and this function also acquires the
rtnl lock and which thus causes a deadlock. Further, if iw_cxgb3 is
loaded _after_ the nic interface is brought up, then the deadlock does
not occur and therefore fw_supports_fastreg() does need to grab the
rtnl lock in that path.
It turns out this code is all useless anyway. The low level driver
will NOT allow the open if the firmware isn't 7.0, so iw_cxgb3 can
always set the MEM_MGT_EXTENSIONS bit. Simplify...
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- MWs don't have local read/write permissions.
- Set the MW_BIND enabled bit if a MR has MW_BIND access.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Set the stag0 and fastreg capability bits only for kernel qps.
- QP_PRIV flag is no longer used, so don't set it.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are a few places where the RDMA CM code handles IPv6 by doing
struct sockaddr addr;
u8 pad[sizeof(struct sockaddr_in6) -
sizeof(struct sockaddr)];
This is fragile and ugly; handle this in a better way with just
struct sockaddr_storage addr;
[ Also roll in patch from Aleksey Senin <alekseys@voltaire.com> to
switch to struct sockaddr_storage and get rid of padding arrays in
struct rdma_addr. ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some module parameters with only one line have the '\n' at the end of the
description. This is not needed nor wanted as after the description the
type (i.e. int) is followed by a newline.
Some modules contain a multi-line description, these are not affected
by this patch.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Ed L. Cashin <ecashin@coraid.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Roland Dreier <rolandd@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
wr->sg_list should be set to the sge pointer passed in, not
priv->cm.rx_sge.
Reported-by: Hoang-Nam Nguyen <HNGUYEN@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4: Update/add Mellanox Technologies copyright lines to mlx4 driver files
mlx4_core: Add VLAN tag field to WQE control segment struct
RDMA/nes: CM connection setup/teardown rework
IPoIB: Correct help text for INFINIBAND_IPOIB_DEBUG
IPoIB/cm: Connected mode is no longer EXPERIMENTAL
RDMA/ucm: BKL is not needed for ib_ucm_open()
RDMA/ucma: BKL is not needed for ucma_open()
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update existing Mellanox copyright lines to 2008, and add such lines
to files where they are missing.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Major rework of CM connection setup/teardown. We had a number of issues
with MPI applications not starting/terminating properly over time.
With these changes we were able to run longer on larger clusters.
* Remove memory allocation from nes_connect() and nes_cm_connect().
* Fix mini_cm_dec_refcnt_listen() when destroying listener.
* Remove unnecessary code from schedule_nes_timer() and nes_cm_timer_tick().
* Functionalize mini_cm_recv_pkt() and process_packet().
* Clean up cm_node->ref_count usage.
* Reuse skbs if available.
Signed-off-by: Faisal Latif <flatif@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The help text for INFINIBAND_IPOIB_DEBUG refers to "ipoib_debugfs,"
which no longer exists. Correct this to talk about the files under
debugfs that are really created.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Connected mode is now tested and used by lots of people. No need to
hide it under CONFIG_EXPERIMENTAL.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
MAINTAINERS: Remove Glenn Streiff from NetEffect entry
mlx4_core: Improve error message when not enough UAR pages are available
IB/mlx4: Add support for memory management extensions and local DMA L_Key
IB/mthca: Keep free count for MTT buddy allocator
mlx4_core: Keep free count for MTT buddy allocator
mlx4_code: Add missing FW status return code
IB/mlx4: Rename struct mlx4_lso_seg to mlx4_wqe_lso_seg
mlx4_core: Add module parameter to enable QoS support
RDMA/iwcm: Remove IB_ACCESS_LOCAL_WRITE from remote QP attributes
IPoIB: Include err code in trace message for ib_sa_path_rec_get() failures
IB/sa_query: Check if sm_ah is NULL in ib_sa_remove_one()
IB/ehca: Release mutex in error path of alloc_small_queue_page()
IB/ehca: Use default value for Local CA ACK Delay if FW returns 0
IB/ehca: Filter PATH_MIG events if QP was never armed
IB/iser: Add support for RDMA_CM_EVENT_ADDR_CHANGE event
RDMA/cma: Add RDMA_CM_EVENT_TIMEWAIT_EXIT event
RDMA/cma: Add RDMA_CM_EVENT_ADDR_CHANGE event
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
Add support for the following operations to mlx4 when device firmware
supports them:
- Send with invalidate and local invalidate send queue work requests;
- Allocate/free fast register MRs;
- Allocate/free fast register MR page lists;
- Fast register MR send queue work requests;
- Local DMA L_Key.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
MTT entries are allocated with a buddy allocator, which just keeps
bitmaps for each level of the buddy table. However, all free space
starts out at the highest order, and small allocations start scanning
from the lowest order. When the lowest order tables have no free
space, this can lead to scanning potentially millions of bits before
finding a free entry at a higher order.
We can avoid this by just keeping a count of how many free entries
each order has, and skipping the bitmap scan when an order is
completely empty. This provides a nice performance boost for a
negligible increase in memory usage.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove IB_ACCESS_LOCAL_WRITE from qp.qp_access_flags because this
attribute is only used to set remote permissions.
Signed-off-by: Dotan Barak <dotanba@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Print the return code of ib_sa_path_rec_get() if it fails to help
debug errors.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If update_sm_ah() fails, it leaves the port's sm_ah as NULL. Then if
the device or module is removed, ib_sa_remove_one() will dereference a
NULL pointer when it calls kref_put(). Fix this by testing if sm_ah
is NULL before dropping the reference.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The pd->lock mutex is released on a successful return, so it should be
released on an error return as well.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some firmware versions report a Local CA ACK Delay of 0. In that
case, return a more sensible default value of 12 (-> 16 msec) instead.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Certain firmware versions sometimes cause spurious PATH_MIG events to
occur during QP creation. Filter these events by making sure PATH_MIG
events are only handed down when they actually make sense (i.e. when
the QP has been armed at least once).
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enhance iser to act upon notification on network stack changes that
make its RDMA connection unaligned with the link used by the stack for
the <src,dst> IPs used to establish the connection.
When RDMA_CM_EVENT_ADDR_CHANGE arrives, just disconnect the
connection, assuming that the user space iscsid daemon will reconnect,
and the new connection will be aligned with the IP stack.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Consumers that want to re-use their QPs in new connections need to
know when the QP has exited the timewait state. Report the timewait
event through the rdma_cm.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an RDMA_CM_EVENT_ADDR_CHANGE event can be used by rdma-cm
consumers that wish to have their RDMA sessions always use the same
links (eg <hca/port>) as the IP stack does. In the current code, this
does not happen when bonding is used and fail-over happened but the IB
link used by an already existing session is operating fine.
Use the netevent notification for sensing that a change has happened
in the IP stack, then scan the rdma-cm ID list to see if there is an
ID that is "misaligned" with respect to the IP stack, and deliver
RDMA_CM_EVENT_ADDR_CHANGE for this ID. The consumer can act on the
event or just ignore it.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This object really should be a struct device, or at least contain a
pointer to a struct device, as it is trying to create a separate device
tree outside of the main device tree. This patch fixes this problem.
It is needed for the class core rework that is being done in the driver
core.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This pointer really is a struct ib_device, not a struct device, so name
it properly to help prevent confusion.
This makes the followon patch in this series much smaller and easier to
understand as well.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (102 commits)
[SCSI] scsi_dh: fix kconfig related build errors
[SCSI] sym53c8xx: Fix bogus sym_que_entry re-implementation of container_of
[SCSI] scsi_cmnd.h: remove double inclusion of linux/blkdev.h
[SCSI] make struct scsi_{host,target}_type static
[SCSI] fix locking in host use of blk_plug_device()
[SCSI] zfcp: Cleanup external header file
[SCSI] zfcp: Cleanup code in zfcp_erp.c
[SCSI] zfcp: zfcp_fsf cleanup.
[SCSI] zfcp: consolidate sysfs things into one file.
[SCSI] zfcp: Cleanup of code in zfcp_aux.c
[SCSI] zfcp: Cleanup of code in zfcp_scsi.c
[SCSI] zfcp: Move status accessors from zfcp to SCSI include file.
[SCSI] zfcp: Small QDIO cleanups
[SCSI] zfcp: Adapter reopen for large number of unsolicited status
[SCSI] zfcp: Fix error checking for ELS ADISC requests
[SCSI] zfcp: wait until adapter is finished with ERP during auto-port
[SCSI] ibmvfc: IBM Power Virtual Fibre Channel Adapter Client Driver
[SCSI] sg: Add target reset support
[SCSI] lib: Add support for the T10 (SCSI) Data Integrity Field CRC
[SCSI] sd: Move scsi_disk() accessor function to sd.h
...
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_addr_{lock,unlock}{,_bh}() helpers.
Use them to protect operations that operate on or read
the network device unicast and multicast address lists.
Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code uses kmalloc() and then just does a bitwise OR operation on
qp->flags in create_qp_common(), which means that qp->flags may
potentially have some unintended bits set. This patch uses kzalloc()
and avoids further explicit clearing of structure members, which also
shrinks the code:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-65 (-65)
function old new delta
create_qp_common 2024 1959 -65
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The RDMA CM has some logic in place to make sure that callbacks on a
given CM ID are delivered to the consumer in a serialized manner.
Specifically it has code to protect against a device removal racing
with a running callback function.
This patch simplifies this logic by using a mutex per ID instead of a
wait queue and atomic variable. This means that cma_disable_remove()
now is more properly named to cma_disable_callback(), and
cma_enable_remove() can now be removed because it just would become a
trivial wrapper around mutex_unlock().
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Keep a pointer to the local (src) netdevice in struct rdma_dev_addr,
and copy it in as part of rdma_copy_addr(). Use rdma_translate_ip()
in cma_new_conn_id() to reduce some code duplication and also make
sure the src_dev member gets set.
In a high-availability configuration the netdevice pointer can be used
by the RDMA CM to align RDMA sessions to use the same links as the IP
stack does under fail-over and route change cases.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Handling the zero STag in receive work request requires some extra
logic in the driver:
- Only set the QP_PRIV bit for kernel mode QPs.
- Add a zero STag build function for recv wrs. The uP needs a PBL
allocated and passed down in the recv WR so it can construct a HW
PBL for the zero STag S/G entries. Note: we need to place a few
restrictions on zero STag usage because of this:
1) all SGEs in a recv WR must either be zero STag or not. No mixing.
2) an individual SGE length cannot exceed 128MB for a zero-stag SGE.
This should be OK since it's not really practical to allocate
such a large chunk of pinned contiguous DMA mapped memory.
- Add an optimized non-zero-STag recv wr format for kernel users.
This is needed to optimize both zero and non-zero STag cracking in
the recv path for kernel users.
- Remove the iwch_ prefix from the static build functions.
- Bump required FW version.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
- Change the IB_DEVICE_ZERO_STAG flag to the transport-neutral name
IB_DEVICE_LOCAL_DMA_LKEY, which is used by iWARP RNICs to indicate 0
STag support and IB HCAs to indicate reserved L_Key support.
- Add a u32 local_dma_lkey member to struct ib_device. Drivers fill
this in with the appropriate local DMA L_Key (if they support it).
- Fix up the drivers using this flag.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The MLX transport requires two extra gather entries for sends (one for
the header and one for the checksum at the end, as the comment says).
However the code checked that max_recv_sge was not too big, instead of
checking max_send_sge as it should have. Fix the code to check the
correct condition.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Exactly when the catastrophic error polling timer function runs is not
important, so use round_jiffies() to save unnecessary wakeups.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since we use del_timer_sync() anyway, there's no need for an
additional flag to tell the timer not to rearm.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Increase IPoIB ring sizes to twice their original sizes (RX: 128->256,
TX: 64->128) to act as a shock absorber for high traffic peaks. With
the current settings, we have seen cases that there are many calls to
netif_stop_queue(), which causes degradation in throughput. Also,
larger receive buffer sizes help IPoIB in CM mode to avoid experiencing
RNR NAK conditions due to insufficient receive buffers at the SRQ.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since IPoIB connected mode does not NETIF_F_SG, we only have one DMA
mapping per send, so we don't need a mapping[] array. Define a new
struct with a single u64 mapping member and use it for the CM tx_ring.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB spe. for SubnGet(NodeInfo) and query HCA says that the vendor
ID field should be the IEEE OUI assigned to the vendor. The ipath
driver was returning the PCI vendor ID instead. This will affect
applications which call ibv_query_device(). The old value was
0x001fc1 or 0x001077, the new value is 0x001175.
The vendor ID doesn't appear to be exported via /sys so that should
reduce possible compatibility issues. I'm only aware of Open MPI as a
major application which depends on this change, and they have made
necessary adjustments.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the driver sets the MTU of the net device outside of its
change_mtu method, it should make use of dev_set_mtu() instead of
directly setting the mtu field of struct netdevice. Otherwise
functions registered to be called upon MTU change will not get called
(this is done through call_netdevice_notifiers() in dev_set_mtu()).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use of this lock is required to synchronize changes to the netdvice's
data structs. Also move the call to ipoib_flush_paths() after the
modification of the netdevice flags in set_mode().
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_mcast_detach() does nothing except call ib_detach_mcast(), so just
use the core API in the one place that does a multicast group detach.
add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-105 (-105)
function old new delta
ipoib_mcast_leave 357 319 -38
ipoib_mcast_detach 67 - -67
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current code will set the Q_Key for any join of a non-sendonly
multicast group. The operation involves a modify QP operation, which
is fairly heavyweight, and is only really required after the join of
the broadcast group. Fix this by adding a parameter to ipoib_mcast_attach()
to control when the Q_Key is set.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
No need for a mutex around calls to ib_attach_mcast/ib_detach_mcast
since these operations are synchronized at the HW driver layer.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPOIB_MCAST_STARTED flag is not used at all since commit b3e2749b
("IPoIB: Don't drop multicast sends when they can be queued"), so
remove it.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Every caller of nes_post_cqp_request() passed it NES_CQP_REQUEST_RING_DOORBELL,
so just remove that parameter and always ring the doorbell.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Faisal Latif <flatif@neteffect.com>
cxgb3 does not currently report the page size capabilities, and
incorrectly reports them internally.
This version changes the bit-shifting to a static value (per Steve's
request).
Signed-off-by: Jon Mason <jon@opengridcomputing.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The patch tries to solve the problem of device going down and paths being
flushed on an SM change event. The method is to mark the paths as candidates for
refresh (by setting the new valid flag to 0), and wait for an ARP
probe a new path record query.
The solution requires a different and less intrusive handling of SM
change event. For that, the second argument of the flush function
changes its meaning from a boolean flag to a level. In most cases, SM
failover doesn't cause LID change so traffic won't stop. In the rare
cases of LID change, the remote host (the one that hadn't changed its
LID) will lose connectivity until paths are refreshed. This is no
worse than the current state. In fact, preventing the device from
going down saves packets that otherwise would be lost.
Signed-off-by: Moni Levy <monil@voltaire.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This gives ehca an autogenerated modalias and therefore enables automatic loading.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add "ipoib_use_lro" module parameter to enable LRO and an
"ipoib_lro_max_aggr" module parameter to set the max number of packets
to be aggregated. Make LRO controllable and LRO statistics accessible
through ethtool.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set IB_QP_CREATE_BLOCK_MULTICAST_LOOPBACK for IPoIB's UD QPs if
supported by the underlying device. This creates an improvement of up
to 39% in bandwidth when sending multicast packets with IPoIB, and an
improvment of 12% in cpu usage.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for handling the IB_QP_CREATE_MULTICAST_BLOCK_LOOPBACK
flag by using the per-multicast group loopback blocking feature of
mlx4 hardware.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Add a new rdma ctl command called RDMA_GET_MIB to the cxgb3 low
level driver to obtain the protocol mib from the rnic hardware.
- Add new iw_cxgb3 provider method to get the MIB from the low level
driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds a sysfs attribute group called "proto_stats" under
/sys/class/infiniband/$device/ and populates this group with protocol
statistics if they exist for a given device. Currently, only iWARP
stats are defined, but the code is designed to allow InfiniBand
protocol stats if they become available. These stats are per-device
and more importantly -not- per port.
Details:
- Add union rdma_protocol_stats in ib_verbs.h. This union allows
defining transport-specific stats. Currently only iwarp stats are
defined.
- Add struct iw_protocol_stats to define the current set of iwarp
protocol stats.
- Add new ib_device method called get_proto_stats() to return protocol
statistics.
- Add logic in core/sysfs.c to create iwarp protocol stats attributes
if the device is an RNIC and has a get_proto_stats() method.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For devices that don't support SRQs, ipoib_cm_post_receive_nonsrq() is
called from both ipoib_cm_handle_rx_wc() and ipoib_cm_nonsrq_init_rx(),
and these two callers are not synchronized against each other.
However, ipoib_cm_post_receive_nonsrq() always reuses the same receive
work request and scatter list structures, so multiple callers can end
up stepping on each other, which leads to posting garbled work
requests.
Fix this by having the caller pass in the ib_recv_wr and ib_sge
structures to use, and allocating new local structures in
ipoib_cm_nonsrq_init_rx().
Based on a patch by Pradeep Satyanarayana <pradeep@us.ibm.com> and
David Wilder <dwilder@us.ibm.com>, with debugging help from Hoang-Nam
Nguyen <hnguyen@de.ibm.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The members struct iwch_rnic_attributes.vendor_id and .vendor_part_id
are write-only, so we might as well get rid of them.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
- set fw_ver
- set hw_ver
- set max_qp_wr to something reasonable
- set max_cqe to something reasonable
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During corner case testing, we noticed that some versions of ehca do
not properly transition to interrupt done in special load situations.
This can be resolved by periodically triggering EOI through H_EOI, if
EQEs are pending.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 65adfa91 ("IB/mlx4: Fix RESET to RESET and RESET to ERROR
transitions") added some extra code to handle a QP state transition
from RESET to ERROR. However, the latest 1.2.1 version of the IB spec
has clarified that this transition is actually not allowed, so we can
remove this extra code again.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit b18aad71 ("IB/mthca: Fix RESET to ERROR transition") added some
extra code to handle a QP state transition from RESET to ERROR.
However, the latest 1.2.1 version of the IB spec has clarified that
this transition is actually not allowed, so we can remove this extra
code again.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I was reviewing the QP state transition diagram in the IB 1.2.1 spec
and the code for qp_state_table[], and noticed that the code allows a
QP to be modified from IB_QPS_RESET to IB_QPS_ERR whereas the notes
for figure 124 (pg 457) specifically says that this transition isn't
allowed. This is a clarification from earlier versions of the IB
spec, which were ambiguous in this area and suggested that the RESET
to ERR transition was allowed.
Fix up the qp_state_table[] to make RESET->ERR not allowed.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX HCAs support the IB_MGMT_CLASS_CONG_MGMT management class, so
process MADs of this class through the MAD_IFC firmware command.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX returns the max message size it supports through the
QUERY_DEV_CAP firmware command. When modifying a QP to RTR, the max
message size for the QP must be specified. This value must not exceed
the value declared through QUERY_DEV_CAP. The current code ignores
the max allowed size and unconditionally sets the value to 2^31. This
patch sets all QPs to the max value allowed as returned from firmware.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- set IB_DEVICE_MEM_MGT_EXTENSIONS capability bit if fw supports it.
- set max_fast_reg_page_list_len device attribute.
- add iwch_alloc_fast_reg_mr function.
- add iwch_alloc_fastreg_pbl
- add iwch_free_fastreg_pbl
- adjust the WQ depth for kernel mode work queues to account for
fastreg possibly taking 2 WR slots.
- add fastreg_mr work request support.
- add local_inv work request support.
- add send_with_inv and send_with_se_inv work request support.
- removed useless duplicate enums/defines for TPT/MW/MR stuff.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds support for the IB "base memory management extension"
(BMME) and the equivalent iWARP operations (which the iWARP verbs
mandates all devices must implement). The new operations are:
- Allocate an ib_mr for use in fast register work requests.
- Allocate/free a physical buffer lists for use in fast register work
requests. This allows device drivers to allocate this memory as
needed for use in posting send requests (eg via dma_alloc_coherent).
- New send queue work requests:
* send with remote invalidate
* fast register memory region
* local invalidate memory region
* RDMA read with invalidate local memory region (iWARP only)
Consumer interface details:
- A new device capability flag IB_DEVICE_MEM_MGT_EXTENSIONS is added
to indicate device support for these features.
- New send work request opcodes IB_WR_FAST_REG_MR, IB_WR_LOCAL_INV,
IB_WR_RDMA_READ_WITH_INV are added.
- A new consumer API function, ib_alloc_mr() is added to allocate
fast register memory regions.
- New consumer API functions, ib_alloc_fast_reg_page_list() and
ib_free_fast_reg_page_list() are added to allocate and free
device-specific memory for fast registration page lists.
- A new consumer API function, ib_update_fast_reg_key(), is added to
allow the key portion of the R_Key and L_Key of a fast registration
MR to be updated. Consumers call this if desired before posting
a IB_WR_FAST_REG_MR work request.
Consumers can use this as follows:
- MR is allocated with ib_alloc_mr().
- Page list memory is allocated with ib_alloc_fast_reg_page_list().
- MR R_Key/L_Key "key" field is updated with ib_update_fast_reg_key().
- MR made VALID and bound to a specific page list via
ib_post_send(IB_WR_FAST_REG_MR)
- MR made INVALID via ib_post_send(IB_WR_LOCAL_INV),
ib_post_send(IB_WR_RDMA_READ_WITH_INV) or an incoming send with
invalidate operation.
- MR is deallocated with ib_dereg_mr()
- page lists dealloced via ib_free_fast_reg_page_list().
Applications can allocate a fast register MR once, and then can
repeatedly bind the MR to different physical block lists (PBLs) via
posting work requests to a send queue (SQ). For each outstanding
MR-to-PBL binding in the SQ pipe, a fast_reg_page_list needs to be
allocated (the fast_reg_page_list is owned by the low-level driver
from the consumer posting a work request until the request completes).
Thus pipelining can be achieved while still allowing device-specific
page_list processing.
The 32-bit fast register memory key/STag is composed of a 24-bit index
and an 8-bit key. The application can change the key each time it
fast registers thus allowing more control over the peer's use of the
key/STag (ie it can effectively be changed each time the rkey is
rebound to a page list).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The connected mode implementation in the IPoIB driver has a large
overhead in the way SKBs are handled in the receive flow. It usually
allocates an SKB with as big as was used in the currently received SKB
and moves unused fragments from the old SKB to the new one. This
involves a loop on all the remaining fragments and incurs overhead on
the CPU. This patch, for small SKBs, allocates an SKB just large
enough to contain the received data and copies to it the data from the
received SKB. The newly allocated SKB is passed to the stack and the
old SKB is reposted.
When running netperf, UDP small messages, without this pach I get:
UDP UNIDIRECTIONAL SEND TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
14.4.3.178 (14.4.3.178) port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
114688 128 10.00 5142034 0 526.31
114688 10.00 1130489 115.71
With this patch I get both send and receive at ~315 mbps.
The reason that send performance actually slows down is as follows:
When using this patch, the overhead of the CPU for handling RX packets
is dramatically reduced. As a result, we do not experience RNR NAK
messages from the receiver which cause the connection to be closed and
reopened again; when the patch is not used, the receiver cannot handle
the packets fast enough so there is less time to post new buffers and
hence the mentioned RNR NACKs. So what happens is that the
application *thinks* it posted a certain number of packets for
transmission but these packets are flushed and do not really get
transmitted. Since the connection gets opened and closed many times,
each time netperf gets the CPU time that otherwise would have been
given to IPoIB to actually transmit the packets. This can be verified
when looking at the port counters -- the output of ifconfig and the
oputput of netperf (this is for the case without the patch):
tx packets
==========
port counter: 1,543,996
ifconfig: 1,581,426
netperf: 5,142,034
rx packets
==========
netperf 1,1304,089
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
The idea is that for QPs with fixed size work requests (eg selective
signaling QPs), before stamping the WQE, we read the value of the DS
field, which gives the effective size of the descriptor as used in the
previous post. Then we stamp only that area, since the rest of the
descriptor is already stamped.
When initializing the send queue buffer, make sure the DS field is
initialized to the max descriptor size so that the subsequent stamping
will be done on the entire descriptor area.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch solves a race that occurs after an event occurs that causes
the SA query module to flush its SM address handle (AH). When SM AH
becomes invalid and needs an update it is handled by the global
workqueue. On the other hand this event is also handled in the IPoIB
driver by queuing work in the ipoib_workqueue that does multicast
joins. Although queuing is in the right order, it is done to 2
different workqueues and so there is no guarantee that the first to be
queued is the first to be executed.
This causes a problem because IPoIB may end up sending an request to
the old SM, which will take a long time to time out (since the old SM
is gone); this leads to a much longer than necessary interruption in
multicast traffer.
The patch sets the SA query module's SM AH to NULL when the event
occurs, and until update_sm_ah() is done, any request that needs sm_ah
fails with -EAGAIN return status.
For consumers, the patch doesn't make things worse. Before the patch,
MADs are sent to the wrong SM so the request gets lost. Consumers can
be improved if they examine the return code and respond to EAGAIN
properly but even without an improvement the situation is not getting
worse.
Signed-off-by: Moni Levy <monil@voltaire.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The license text for several files references a third software license
that was inadvertently copied in. Update the license to what was
intended. This update was based on a request from HP.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove an explicit memset(..., 0, ...) of a 'listener' structure
allocated with kzalloc().
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Acked-by: Faisal Latif <faisal@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The SRP initiator is currently using ib_find_cached_pkey() and
ib_get_cached_gid() in situations where the uncached ib_find_pkey()
and ib_query_gid() functions serve just as well: sleeping is allowed
and performance is not an issue. Since we want to eliminate the
cached operations in the long term, convert SRP to use the uncached
variants.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes two bugs that are related.
1. Old tools did not set can_queue/cmds_max. This patch modifies
libiscsi so that when we add the host we catch this and set it
to the default.
2. iscsi_tcp thought that the scsi command that was passed to
the eh functions needed a iscsi_cmd_task allocated for it. It
only needed a mgmt task, and now it does not matter since it
all comes from the same pool and libiscsi handles this for the
drivers. ib_iser had copied iscsi_tcp's code and set can_queue
to its max - 1 to handle this. So this patch removes the max -1,
and just sets it to the max.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The recv lock was defined so the iscsi layer could block
the recv path from processing IO during recovery. It
turns out iser just set a lock to that pointer which was pointless.
We now disconnect the transport connection before doing recovery
so we do not need the recv lock. For iscsi_tcp we still stop
the recv path incase older tools are being used.
This patch also has iscsi_itt_to_ctask user grab the session lock
and has the caller access the task with the lock or get a ref
to it in case the target is broken and sends a tmf success response
then sends data or a response for the command that was supposed to
be affected bty the tmf.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds two new attrs used for creating initiator ports and
binding sessions to hardware.
The session level initiatorname:
Since bnx2i does a scsi_host per host device, we need to add the
iface initiator port settings on the session, so we can create
multiple initiator ports (each with different inames) per device/scsi_host.
The current iname reflects that qla4xxx can have one iname per hba, and we are
allocating a host per session for software. The iname on the host will
remain so we can export and set the hba level qla4xxx setting.
The ifacename attr:
To bind a session to a some peice of hardware in userspace we maintain
some mappings, but during boot or iscsid restart (iscsid contains the user
space part of the driver) we need to be able to figure out which of those
host mappings abstractions maps to certain sessions. This patch adds
a ifacename attr, which userspace can set to id the host side of the
endpoint across pivot_roots and iscsid restarts.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This hooks iser into the iscsi endpoint code. Previously it handled the
lookup and allocation. This has been made generic so bnx2i and iser can
share it. It also allows us to pass iser the leading conn's ep, so we
know the ib_deivce being used and can set it as the scsi_host's parent.
And that allows scsi-ml to set the dma_mask based on those values.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently we duplicate the list of sessions, because we were using the
test for if a session was on the host list to indicate if the session
was bound or unbound. We can instead use the target_id and fix up
the class so that drivers like bnx2i do not have to manage the target id
space.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This handles the iscsi_cmd_task rename and renames
the iser cmd task to iser task.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert ib_iser to support merged tasks.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently to get a ctask from the session cmd array, you have to
know to use the itt modifier. To make this easier on LLDs and
so in the future we can easilly kill the session array and use
the host shared map instead, this patch adds a nice wrapper
to strip the itt into a session->cmds index and return a ctask.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After the stop_conn callback has returned the LLD should not
touch the scsi cmds. iscsi_tcp and libiscsi use the
conn->recv_lock and suspend_rx field to halt recv path
processing, but iser does not have any protection.
This patch modifies iser so that userspace can just
call the ep_disconnect callback, which will halt
all recv IO, before calling the stop_conn callback so
we do not have to worry about the conn->recv_lock and
suspend rx field. iser just needs to stop the send side
from accessing the ib conn.
Fixup to handle when the ep poll fails and ep disconnect
is called from Erez.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This removes the session and conn data_size fields from the iscsi_transport.
Just pass in the value like with host allocation. This patch also makes
it so the LLD iscsi_conn data is allocated with the iscsi_cls_conn.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This finishes the host/session unbinding, by adding some helpers
to add and remove hosts and the session they manage.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bnx2i allocates a host per netdevice but will use libiscsi,
so this unbinds the session from the host in that code.
This will also be useful for the iser parent device dma settings
fixes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
max_cmd_len and max_conn are not really used. max_cmd_len is
always 16 and can be set by the LLD. max_conn is always one
since we do not support MCS.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iscsi offload (bnx2i and qla4xx) allocate a scsi host per hba,
so the session creation path needs a shost/host_no argument.
Software iscsi/iser will follow the same behabior as before
where it allcoates a host per session, but in the future iser
will probably look more like bnx2i where the host's parent is
the hardware (rnic for iser and for bnx2i it is the nic), because
it does not use a socket layer like how iscsi_tcp does.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove explicit lock_kernel() calls and document why the code is safe.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The change to iwch_provider.c in commit f4e91eb4 ("IB: convert struct
class_device to struct device") undid the fix done in commit 7f049f2f
("RDMA/cxgb3: Hold rtnl_lock() around ethtool get_drvinfo call"). It
removed the calls to rtnl_lock() that serialized the iw_cxgb3 ethtool
ops calls into the cxgb3 driver. This locking is needed to avoid
messing up the internal state of the cxgb3 driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove explicit lock_kernel() calls and document why the code is safe.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Current memfree FW has a bug which in some cases, assumes that ICM
pages passed to it are cleared. This patch uses __GFP_ZERO to
allocate all ICM pages passed to the FW. Once firmware with a fix is
released, we can make the workaround conditional on firmware version.
This fixes the bug reported by Arthur Kepner <akepner@sgi.com> here:
http://lists.openfabrics.org/pipermail/general/2008-May/050026.html
Cc: <stable@kernel.org>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Rewritten to be a one-liner using __GFP_ZERO instead of vmap()ing
ICM memory and memset()ing it to 0. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All of the open() functions which don't need the BKL on their face may
still depend on its acquisition to serialize opens against driver
initialization. So make those functions acquire then release the BKL to be
on the safe side.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Roland Dreier