Non-PCI devices can use the entire 32-bit range, PCI dittos are
limited to the first 64MiB.
Also actually setup coherent_dma_mask.
The patch has been verified on a board with 128MiB memory, one
ipx4xx_eth device and a e100 PCI device.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch fixes the following BUG:
> kernel BUG at mm/vmalloc.c:1132!
> PC is at vm_area_add_early+0x20/0x84
> LR is at add_static_vm_early+0xc/0x60
>
> The problem is cns3xxx_pcie_init() (device_initcall) calls the "early"
> iotable_init().
Instead of merely calling the PCIe iotable_init() from
machine_desc->map_io(), this patch adds the required mappings to the
main CNS3xxx mapping table. This means we don't convert .pfn back to
virtual addresses in pcie.c. The size of the address space consumed for
PCIe control is reduced from 96 MiB (6 * 16 MiB) to about 32 MiB (this
doesn't include MMIO address space required by PCI devices):
- Size of the PCIe "host" mapping is reduced from 16 MiB to 4 KiB.
It's a PCI configuration address space for the local (on-chip) PCIe
bridge.
- Size of the "CFG0" mapping is reduced from 16 MiB to 64 KiB. It's for
Type 0 Configuration accesses, i.e., accesses to the single device
(with possible "functions") on the other end of the PCIe link.
We really only need a 4 KiB page at 0x8000 (see the offset
calculation in cns3xxx_pci_cfg_base()). There is still a potential
problem with PCI bus numbers > 0xF, are they supported?
- The code in cns3xxx_pci_cfg_base() and cns3xxx_pcie_hw_init() should
be clearer now.
- The maximum address space allocated for PCI MMIO is now correctly
shown in /proc/iomem as 176 MiB (per each of the two PCI "domains"
- previously only 16 MiB were reserved).
This patch has been tested on Gateworks Laguna board, masqueraded as
CNS3420VB.
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
WARNING: at drivers/irqchip/irq-gic.c:952 gic_init_bases+0xe4/0x2b8()
Cannot allocate irq_descs @ IRQ16, assuming pre-allocated
Backtrace:
gic_init_bases from cns3xxx_init_irq+0x24/0x34
cns3xxx_init_irq from init_IRQ+0x24/0x2c
init_IRQ from start_kernel+0x1a8/0x338
start_kernel from 0x2000806c
The problem is that 64 CNS3xxx CPU interrupts, starting at 32, are
allocated by the ARM platform-independent code (as requested by
machine_desc->nr_irqs = 96), and then the GIC code tries to allocate
them again.
Tested on Gateworks Laguna board, masqueraded as CNS3420VB.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=NkqH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap fixes for v3.15 merge window" from Tony Lindgren:
Fixes for omaps that would be good to get in before v3.15-rc1.
* tag 'omap-for-v3.15/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: hwmod data: correct the idlemodes for spinlock
ARM: dts: am33xx: correcting dt node unit address for usb
ARM: dts: omap4/5: Use l3_ick for the gpmc node
CLK: TI: OMAP4/5/DRA7: Remove gpmc_fck from dummy clocks
ARM: OMAP4: Fix definition of IS_PM44XX_ERRATUM
ARM: OMAP2+: INTC: Acknowledge stuck active interrupts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The spinlock module's SYSCONFIG register does not support
smart wakeup, so remove this flag from the idle modes in
the spinlock hwmod definition.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DT node's unit address should be its own register offset address to make it a
unique across the system. This patch corrects the incorrect USB entries with
correct register offset for unit address.
Cc: stable@vger.kernel.org # v3.12+
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPMC clock is derived from l3_ick. The simplest solution is
to reference directly l3_ick to provide the GPMC fck in order to
get correct timings. The real management of the clock is left to
hwmod.
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just like IS_PM34XX_ERRATUM, IS_PM44XX_ERRATUM is valid only if
CONFIG_PM is enabled, else, disabling CONFIG_PM results in build
failure complaining about the following:
arch/arm/mach-omap2/built-in.o: In function `omap4_boot_secondary':
:(.text+0x8a70): undefined reference to `pm44xx_errata'
Fixes: c962184 (ARM: OMAP4: PM: add errata support)
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.ocm>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When an interrupt has become active on the INTC it will stay active
until it is acked, even if masked or de-asserted. The
INTC_PENDING_IRQn registers are however updated and since these are
used by omap_intc_handle_irq to determine which interrupt to handle,
it will never see the active interrupt. This will result in a storm of
useless interrupts that is only stopped when another higher priority
interrupt is asserted.
Fix by sending the INTC an acknowledge if we find no interrupts to
handle.
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A collection of fixes for ARM platforms. Most are fixes for DTS files,
mostly from DT conversion on OMAP which is still finding a few issues here
and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache configuration
fix for Tegra, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=i7LS
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes for ARM platforms. Most are fixes for DTS
files, mostly from DT conversion on OMAP which is still finding a few
issues here and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache
configuration fix for Tegra, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
ARM: tegra: only run PL310 init on systems with one
ARM: tegra: Add head numbers to display controllers
ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
ARM: tegra: fix RTC0 alias for Cardhu
ARM: dove: dt: revert PMU interrupt controller node
Documentation: dt: OMAP: Update Overo/Tobi
ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
ARM: dts: omap3-tobi: Use the correct vendor prefix
ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
ARM: OMAP2+: Remove legacy macros for zoom platforms
ARM: OMAP2+: Remove MACH_NOKIA_N800
ARM: dts: N900: add missing compatible property
ARM: dts: N9/N950: fix boot hang with 3.14-rc1
ARM: OMAP1: nokia770: enable tahvo-usb
ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
ARM: dts: omap3-gta04: Fix mmc1 properties.
ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
ARM: OMAP2+: add missing ARCH_HAS_OPP
...
Pull x86 fixes from Thomas Gleixner:
- a bugfix which prevents a divide by 0 panic when the newly introduced
try_msr_calibrate_tsc() fails
- enablement of the Baytrail platform to utilize the newfangled msr
based calibration
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: tsc: Add missing Baytrail frequency to the table
x86, tsc: Fallback to normal calibration if fast MSR calibration fails
This branch contains a bug fix for the way devicetree code identifies
the type of device. Device drivers can contain a list of of_device_ids,
but it more than one entry will match, then the device driver may choose
the wrong one. Commit 105353145e, "match each node compatible against
all given matches first", was queued for v3.14 but ended up causing
other bugs. Commit 06b29e76a7 attempted to fix it but it had other bugs.
Merely reverting the fix and waiting until v3.15 isn't a good option
because there is code in v3.14 that depends on the revised behaviour to
boot.
This branch should finally fixes the problem correctly. This time
instead of just hoping that the patch is correct, this branch also adds
new testcases that validate the behaviour.
The changes in this branch are larger than I would like for a -rc pull,
but moving the test case data out of out of arch/arm so that it could be
validated on other architectures was important.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTB2qsAAoJEMWQL496c2LNmvYQAJPwmc3f76L/HxxuJZ3TVpFF
2JhtCUyzTrsuebDSanAZLhzwCrIL4N8I/1rZObvkQuxUEUPNg4Khx9chMYwsG7L7
vbdr+3bkYnwaaGHzoH0NnNM5x1NLm29WOeHaWvT9Nm8iA1399AaOeAXniLQrTgBv
LxipQc3SZpRSKdCDCi2y32TESMJcN7FT1aD4EKHAZocmXMpMaxEYQ2eFO70Txf5O
1SbNkZ7LsAnm1TmoH7nf0um9IFX7bvt2KkonpKBL2mOoDfq40pBosV3Zt2JwaeDy
3nkBeAFs3YvIDjZy3h+WdWLXlF9E29P7CXreE/uSJTnoYft6aCDfgz15USc2j2OA
BTnK0kqJ3NWu6YAKrQHHoQmisnuDwg84oEK0JLJCfMcA3IOCBXV+iYHbo41j/dO5
yprnS1zms6UZuOXV2RjseQ34THkR3oDPbSxKmFTK/KGaa568ES0l1ZPAsvuVZqNr
5elDskt+lfF96WLGbyC0DP5Zib/0eFTbf18p///4lefkr6ysT+CdIJTsRj0/Uz0V
40nwCJH2t+wVCtcI/+mo3yvc4C77OoRhAOAxz8D9YkOlt8ilfgIDeAc1krAAa09T
0KfpfkLDvXEccZF+Jo2Z9TU7QFdeLVK/QAsvCZN4EcMU31ePEldMiniZ69/aySPl
D/ahG24w1pakKXujtJK2
=wJz0
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree fixes from Grant Likely:
"Device tree compatible match order bug fix
This branch contains a bug fix for the way devicetree code identifies
the type of device. Device drivers can contain a list of
of_device_ids, but it more than one entry will match, then the device
driver may choose the wrong one. Commit 105353145e, "match each node
compatible against all given matches first", was queued for v3.14 but
ended up causing other bugs. Commit 06b29e76a7 attempted to fix it
but it had other bugs. Merely reverting the fix and waiting until
v3.15 isn't a good option because there is code in v3.14 that depends
on the revised behaviour to boot.
This branch should finally fixes the problem correctly. This time
instead of just hoping that the patch is correct, this branch also
adds new testcases that validate the behaviour.
The changes in this branch are larger than I would like for a -rc
pull, but moving the test case data out of out of arch/arm so that it
could be validated on other architectures was important"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of: Add self test for of_match_node()
of: Move testcase FDT data into drivers/of
of: reimplement the matching method for __of_match_node()
Revert "of: search the best compatible match first in __of_match_node()"
This patch updates the CBOX PMU filters mapping tables for SNB-EP
and IVT (model 45 and 62 respectively).
The NID umask always comes in addition to another umask.
When set, the NID filter is applied.
The current mapping tables were missing some code/umask
combinations to account for the NID umask. This patch
fixes that.
Cc: mingo@elte.hu
Cc: ak@linux.intel.com
Reviewed-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140219131018.GA24475@quad
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current code simply assumes Intel Arch PerfMon v2+ to have
the IA32_PERF_CAPABILITIES MSR; the SDM specifies that we should check
CPUID[1].ECX[15] (aka, FEATURE_PDCM) instead.
This was found by KVM which implements v2+ but didn't provide the
capabilities MSR. Change the code to DTRT; KVM will also implement the
MSR and return 0.
Cc: pbonzini@redhat.com
Reported-by: "Michael S. Tsirkin" <mst@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140203132903.GI8874@twins.programming.kicks-ass.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When using BTS on Core i7-4*, I get the below kernel warning.
$ perf record -c 1 -e branches:u ls
Message from syslogd@labpc1501 at Nov 11 15:49:25 ...
kernel:[ 438.317893] Uhhuh. NMI received for unknown reason 31 on CPU 2.
Message from syslogd@labpc1501 at Nov 11 15:49:25 ...
kernel:[ 438.317920] Do you have a strange power saving mode enabled?
Message from syslogd@labpc1501 at Nov 11 15:49:25 ...
kernel:[ 438.317945] Dazed and confused, but trying to continue
Make intel_pmu_handle_irq() take the full exit path when returning early.
Cc: eranian@google.com
Cc: peterz@infradead.org
Cc: mingo@kernel.org
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1392425048-5309-1-git-send-email-andi@firstfloor.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull sparc fixes from David Miller:
"Three minor fixes from David Howells and Paul Gortmaker"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
Sparc: sparc_cpu_model isn't in asm/system.h any more [ver #2]
sparc32: make copy_to/from_user_page() usable from modular code
sparc32: fix build failure for arch_jump_label_transform
Pull cgroup fixes from Tejun Heo:
"Quite a few fixes this time.
Three locking fixes, all marked for -stable. A couple error path
fixes and some misc fixes. Hugh found a bug in memcg offlining
sequence and we thought we could fix that from cgroup core side but
that turned out to be insufficient and got reverted. A different fix
has been applied to -mm"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: update cgroup_enable_task_cg_lists() to grab siglock
Revert "cgroup: use an ordered workqueue for cgroup destruction"
cgroup: protect modifications to cgroup_idr with cgroup_mutex
cgroup: fix locking in cgroup_cfts_commit()
cgroup: fix error return from cgroup_create()
cgroup: fix error return value in cgroup_mount()
cgroup: use an ordered workqueue for cgroup destruction
nfs: include xattr.h from fs/nfs/nfs3proc.c
cpuset: update MAINTAINERS entry
arm, pm, vmpressure: add missing slab.h includes
Pull DMA-mapping fixes from Marek Szyprowski:
"This contains fixes for incorrect atomic test in dma-mapping subsystem
for ARM and x86 architecture"
* 'fixes-for-v3.14' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
x86: dma-mapping: fix GFP_ATOMIC macro usage
ARM: dma-mapping: fix GFP_ATOMIC macro usage
The testcase data is usable by any platform. This patch moves it into
the drivers/of directory so it can be included by any architecture.
Using the test cases requires manually adding #include <testcases.dtsi>
to the end of the boards .dtsi file and enabling CONFIG_OF_SELFTEST. Not
pretty though. A useful project would be to make the testcase code
easier to execute.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
While copy_to/from_user_page() users are uncommon, there is one in
drivers/staging/lustre/lustre/libcfs/linux/linux-curproc.c which leads
to the following:
ERROR: "sparc32_cachetlb_ops" [drivers/staging/lustre/lustre/libcfs/libcfs.ko] undefined!
during routine allmodconfig build coverage. The reason this happens
is as follows:
In arch/sparc/include/asm/cacheflush_32.h we have:
#define flush_cache_page(vma,addr,pfn) \
sparc32_cachetlb_ops->cache_page(vma, addr)
#define copy_to_user_page(vma, page, vaddr, dst, src, len) \
do { \
flush_cache_page(vma, vaddr, page_to_pfn(page));\
memcpy(dst, src, len); \
} while (0)
#define copy_from_user_page(vma, page, vaddr, dst, src, len) \
do { \
flush_cache_page(vma, vaddr, page_to_pfn(page));\
memcpy(dst, src, len); \
} while (0)
However, sparc32_cachetlb_ops isn't exported and hence the error.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In arch/sparc/Kernel/Makefile, we see:
obj-$(CONFIG_SPARC64) += jump_label.o
However, the Kconfig selects HAVE_ARCH_JUMP_LABEL unconditionally
for all SPARC. This in turn leads to the following failure when
doing allmodconfig coverage builds:
kernel/built-in.o: In function `__jump_label_update':
jump_label.c:(.text+0x8560c): undefined reference to `arch_jump_label_transform'
kernel/built-in.o: In function `arch_jump_label_transform_static':
(.text+0x85cf4): undefined reference to `arch_jump_label_transform'
make: *** [vmlinux] Error 1
Change HAVE_ARCH_JUMP_LABEL to be conditional on SPARC64 so that it
matches the Makefile.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel Baytrail is based on Silvermont core so MSR_FSB_FREQ[2:0] == 0 means
that the CPU reference clock runs at 83.3MHz. Add this missing frequency to
the table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1392810750-18660-2-git-send-email-mika.westerberg@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If we cannot calibrate TSC via MSR based calibration
try_msr_calibrate_tsc() stores zero to fast_calibrate and returns that
to the caller. This value gets then propagated further to clockevents
code resulting division by zero oops like the one below:
divide error: 0000 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.13.0+ #47
task: ffff880075508000 ti: ffff880075506000 task.ti: ffff880075506000
RIP: 0010:[<ffffffff810aec14>] [<ffffffff810aec14>] clockevents_config.part.3+0x24/0xa0
RSP: 0000:ffff880075507e58 EFLAGS: 00010246
RAX: ffffffffffffffff RBX: ffff880079c0cd80 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffffffffff
RBP: ffff880075507e70 R08: 0000000000000001 R09: 00000000000000be
R10: 00000000000000bd R11: 0000000000000003 R12: 000000000000b008
R13: 0000000000000008 R14: 000000000000b010 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff880079c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff880079fff000 CR3: 0000000001c0b000 CR4: 00000000001006f0
Stack:
ffff880079c0cd80 000000000000b008 0000000000000008 ffff880075507e88
ffffffff810aecb0 ffff880079c0cd80 ffff880075507e98 ffffffff81030168
ffff880075507ed8 ffffffff81d1104f 00000000000000c3 0000000000000000
Call Trace:
[<ffffffff810aecb0>] clockevents_config_and_register+0x20/0x30
[<ffffffff81030168>] setup_APIC_timer+0xc8/0xd0
[<ffffffff81d1104f>] setup_boot_APIC_clock+0x4cc/0x4d8
[<ffffffff81d0f5de>] native_smp_prepare_cpus+0x3dd/0x3f0
[<ffffffff81d02ee9>] kernel_init_freeable+0xc3/0x205
[<ffffffff8177c910>] ? rest_init+0x90/0x90
[<ffffffff8177c91e>] kernel_init+0xe/0x120
[<ffffffff8178deec>] ret_from_fork+0x7c/0xb0
[<ffffffff8177c910>] ? rest_init+0x90/0x90
Prevent this from happening by:
1) Modifying try_msr_calibrate_tsc() to return calibration value or zero
if it fails.
2) Check this return value in native_calibrate_tsc() and in case of zero
fallback to use normal non-MSR based calibration.
[mw: Added subject and changelog]
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1392810750-18660-1-git-send-email-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix tegra_init_cache() to check whether the system has a PL310 cache
before touching the PL310 registers. This prevents access to non-existent
registers on Tegra114 and later.
Note for stable kernels:
In <= v3.12, the file to patch is arch/arm/mach-tegra/common.c.
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The number of the head specifies the index of the display controller
unit and is required to properly configure outputs so that they receive
video data from the correct source.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
When building a kernel image with only CONFIG_CPU_IDLE but no CONFIG_PM,
we will get the following link error.
LD init/built-in.o
arch/arm/mach-imx/built-in.o: In function `imx6q_enter_wait':
platform-spi_imx.c:(.text+0x25c0): undefined reference to `imx6q_set_lpm'
platform-spi_imx.c:(.text+0x25d4): undefined reference to `imx6q_set_lpm'
arch/arm/mach-imx/built-in.o: In function `imx6q_cpuidle_init':
platform-spi_imx.c:(.init.text+0x75d4): undefined reference to `imx6q_set_chicken_bit'
make[1]: *** [vmlinux] Error 1
Since pm-imx6q.c has been a collection of library functions that access
CCM low-power registers used by not only suspend but also cpuidle and
other drivers, let's build pm-imx6q.c independently of CONFIG_PM to fix
above error.
Reported-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable@vger.kernel.org
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This alias entry was evidently cut/paste from a different board, and
not correctly updated to match Cardhu. Fix this.
Fixes: 553c0a200e ("ARM: tegra: set up /aliases entries for RTCs")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
"A range of ARM fixes. Biggest change is the stage-2 attributes used
for for hyp mode which were wrong. I've killed some bits in a couple
of DT files which turned out not to be required, and a few other
fixes.
One fix touches code outside of arch/arm, which is related to sorting
out the DMA masks correctly. There is a long standing issue with the
conversion from PFNs to addresses where people assume that shifting an
unsigned long left by PAGE_SHIFT results in a correct address. This
is not the case with C: the integer promotion happens at assignment
after evaluation. This fixes the recently introduced dma_max_pfn()
function, but there's a number of other places where we try this
directly on an unsigned long in the mm code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7957/1: add DSB after icache flush in __flush_icache_all()
Fix uses of dma_max_pfn() when converting to a limiting address
ARM: 7955/1: spinlock: ensure we have a compiler barrier before sev
ARM: 7953/1: mm: ensure TLB invalidation is complete before enabling MMU
ARM: 7952/1: mm: Fix the memblock allocation for LPAE machines
ARM: 7950/1: mm: Fix stage-2 device memory attributes
ARM: dts: fix spdif pinmux configuration
The corresponding driver didn't make it into v3.14, so we need to remove
the node. Dove systems fail to boot with the node present and no
driver.
This node will be re-added when the driver makes it to mainline.
Reported-by: Jean-Francois Moine <moinejf@free.fr>
Tested-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add DSB after icache flush to complete the cache maintenance operation.
Signed-off-by: Vinayak Kale <vkale@apm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull AVR32 fixes from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: add generic vga.h to Kbuild
avr32: add generic ioremap_wc() definition in io.h
avr32: Makefile: add '-D__linux__' flag for gcc-4.4.7 use
avr32: fix missing module.h causing build failure in mimc200/fram.c
Pull powerpc fixes from Ben Herrenschmidt:
"Here are some more powerpc fixes for 3.14
The main one is a nasty issue with the NUMA balancing support which
requires a small generic change and the addition of a new accessor to
set _PAGE_NUMA. Both have been reviewed and acked by Mel and Rik.
The changelog should have plenty of details but basically, without
this fix, we get random user segfaults and/or corruptions due to
missing TLB/hash flushes. Aneesh series of 3 patches fixes it.
We have some vDSO vs. perf fixes from Anton, some small EEH fixes
from Gavin, a ppc32 regression vs the stack overflow detector, and a
fix for the way we handle PCIe host bridge speed settings on pseries
(which is needed for proper operations of AMD graphics cards on
Power8)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/eeh: Disable EEH on reboot
powerpc/eeh: Cleanup on eeh_subsystem_enabled
powerpc/powernv: Rework EEH reset
powerpc: Use unstripped VDSO image for more accurate profiling data
powerpc: Link VDSOs at 0x0
mm: Use ptep/pmdp_set_numa() for updating _PAGE_NUMA bit
mm: Dirty accountable change only apply to non prot numa case
powerpc/mm: Add new "set" flag argument to pte/pmd update function
powerpc/pseries: Add Gen3 definitions for PCIE link speed
powerpc/pseries: Fix regression on PCI link speed
powerpc: Set the correct ksp_limit on ppc32 when switching to irq stack
Need add generic "vga.h", or can not pass building for allmodconfig,
the related error:
CC [M] drivers/gpu/drm/drm_irq.o
In file included from include/linux/vgaarb.h:34,
from drivers/gpu/drm/drm_irq.c:42:
include/video/vga.h:22:21: error: asm/vga.h: No such file or directory
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
Need generic ioremap_wc(), or can not pass compiling with allmodconfig,
the related error:
CC [M] drivers/gpu/drm/drm_bufs.o
drivers/gpu/drm/drm_bufs.c: In function 'drm_addmap_core':
drivers/gpu/drm/drm_bufs.c:217: error: implicit declaration of function 'ioremap_wc'
drivers/gpu/drm/drm_bufs.c:218: warning: assignment makes pointer from integer without a cast
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
For avr32 cross compiler, do not define '__linux__' internally, so it
will cause issue with allmodconfig.
The related error:
CC [M] fs/coda/psdev.o
In file included from include/linux/coda.h:64,
from fs/coda/psdev.c:45:
include/uapi/linux/coda.h:221: error: expected specifier-qualifier-list before 'u_quad_t'
The related toolchain version (which only download, not re-compile):
[root@gchen linux-next]# /upstream/toolchain/download/avr32-gnu-toolchain-linux_x86/bin/avr32-gcc -v
Using built-in specs.
Target: avr32
Configured with: /data2/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/src/gcc/configure --target=avr32 --host=i686-pc-linux-gnu --build=x86_64-pc-linux-gnu --prefix=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --enable-languages=c,c++ --disable-nls --disable-libssp --disable-libstdcxx-pch --with-dwarf2 --enable-version-specific-runtime-libs --disable-shared --enable-doc --with-mpfr-lib=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86/lib --with-mpfr-include=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86/include --with-gmp=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --with-mpc=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --enable-__cxa_atexit --disable-shared --with-newlib --with-pkgversion=AVR_32_bit_GNU_Toolchain_3.4.2_435 --with-bugurl=http://www
.atmel.com/avr
Thread model: single
gcc version 4.4.7 (AVR_32_bit_GNU_Toolchain_3.4.2_435)
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
Cc: stable@vger.kernel.org
Causing this:
In file included from arch/avr32/boards/mimc200/fram.c:13:
include/linux/miscdevice.h:51: error: field 'list' has incomplete type
include/linux/miscdevice.h:55: error: expected specifier-qualifier-list before 'mode_t'
arch/avr32/boards/mimc200/fram.c:42: error: 'THIS_MODULE' undeclared here (not in a function)
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: stable@vger.kernel.org
We possiblly detect EEH errors during reboot, particularly in kexec
path, but it's impossible for device drivers and EEH core to handle
or recover them properly.
The patch registers one reboot notifier for EEH and disable EEH
subsystem during reboot. That means the EEH errors is going to be
cleared by hardware reset or second kernel during early stage of
PCI probe.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch cleans up variable eeh_subsystem_enabled so that we needn't
refer the variable directly from external. Instead, we will use
function eeh_enabled() and eeh_set_enable() to operate the variable.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When doing reset in order to recover the affected PE, we issue
hot reset on PE primary bus if it's not root bus. Otherwise, we
issue hot or fundamental reset on root port or PHB accordingly.
For the later case, we didn't cover the situation where PE only
includes root port and it potentially causes kernel crash upon
EEH error to the PE.
The patch reworks the logic of EEH reset to improve the code
readability and also avoid the kernel crash.
Cc: stable@vger.kernel.org
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are seeing a lot of hits in the VDSO that are not resolved by perf.
A while(1) gettimeofday() loop shows the issue:
27.64% [vdso] [.] 0x000000000000060c
22.57% [vdso] [.] 0x0000000000000628
16.88% [vdso] [.] 0x0000000000000610
12.39% [vdso] [.] __kernel_gettimeofday
6.09% [vdso] [.] 0x00000000000005f8
3.58% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.94% [vdso] [.] __kernel_datapage_offset
2.90% test [.] main
We are using a stripped VDSO image which means only symbols with
relocation info can be resolved. There isn't a lot of point to
stripping the VDSO, the debug info is only about 1kB:
4680 arch/powerpc/kernel/vdso64/vdso64.so
5815 arch/powerpc/kernel/vdso64/vdso64.so.dbg
By using the unstripped image, we can resolve all the symbols in the
VDSO and the perf profile data looks much better:
76.53% [vdso] [.] __do_get_tspec
12.20% [vdso] [.] __kernel_gettimeofday
5.05% [vdso] [.] __get_datapage
3.20% test [.] main
2.92% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
perf is failing to resolve symbols in the VDSO. A while (1)
gettimeofday() loop shows:
93.99% [vdso] [.] 0x00000000000005e0
3.12% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.81% test [.] main
The reason for this is that we are linking our VDSO shared libraries
at 1MB, which is a little weird. Even though this is uncommon, Alan
points out that it is valid and we should probably fix perf userspace.
Regardless, I can't see a reason why we are doing this. The code
is all position independent and we never rely on the VDSO ending
up at 1M (and we never place it there on 64bit tasks).
Changing our link address to 0x0 fixes perf VDSO symbol resolution:
73.18% [vdso] [.] 0x000000000000060c
12.39% [vdso] [.] __kernel_gettimeofday
3.58% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.94% [vdso] [.] __kernel_datapage_offset
2.90% test [.] main
We still have some local symbol resolution issues that will be
fixed in a subsequent patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Archs like ppc64 doesn't do tlb flush in set_pte/pmd functions when using
a hash table MMU for various reasons (the flush is handled as part of
the PTE modification when necessary).
ppc64 thus doesn't implement flush_tlb_range for hash based MMUs.
Additionally ppc64 require the tlb flushing to be batched within ptl locks.
The reason to do that is to ensure that the hash page table is in sync with
linux page table.
We track the hpte index in linux pte and if we clear them without flushing
hash and drop the ptl lock, we can have another cpu update the pte and can
end up with duplicate entry in the hash table, which is fatal.
We also want to keep set_pte_at simpler by not requiring them to do hash
flush for performance reason. We do that by assuming that set_pte_at() is
never *ever* called on a PTE that is already valid.
This was the case until the NUMA code went in which broke that assumption.
Fix that by introducing a new pair of helpers to set _PAGE_NUMA in a
way similar to ptep/pmdp_set_wrprotect(), with a generic implementation
using set_pte_at() and a powerpc specific one using the appropriate
mechanism needed to keep the hash table in sync.
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pte_update() is a powerpc-ism used to change the bits of a PTE
when the access permission is being restricted (a flush is
potentially needed).
It uses atomic operations on when needed and handles the hash
synchronization on hash based processors.
It is currently only used to clear PTE bits and so the current
implementation doesn't provide a way to also set PTE bits.
The new _PAGE_NUMA bit, when set, is actually restricting access
so it must use that function too, so this change adds the ability
for pte_update() to also set bits.
We will use this later to set the _PAGE_NUMA bit.
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rev3 of the PCI Express Base Specification defines a Supported Link
Speeds Vector where the bit definitions within this field are:
Bit 0 - 2.5 GT/s
Bit 1 - 5.0 GT/s
Bit 2 - 8.0 GT/s
This vector definition is used by the platform firmware to export the
maximum and current link speeds of the PCI bus via the
"ibm,pcie-link-speed-stats" device-tree property.
This patch updates pseries_root_bridge_prepare() to detect Gen3
speed buses (defined by 0x04).
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 5091f0c (powerpc/pseries: Fix PCIE link speed endian issue)
introduced a regression on the PCI link speed detection using the
device-tree property. The ibm,pcie-link-speed-stats property is composed
of two 32-bit integers, the first one being the maxinum link speed and
the second the current link speed. The changes introduced by the
aforementioned commit are considering just the first integer.
Fix this issue by changing how the property is accessed, using the
helper functions to properly access the array of values. The explicit
byte swapping is not needed anymore here, since it's done by the helper
functions.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simon Kågström