On some EHCI usb debug controllers, the EHCI debug device will fail to
be seen after a port reset, after a warm reset. Two options exist to
get the device to initialize correctly.
Option 1 is to unplug and plug in the device.
Option 2 is to use the EHCI port test to get the usb debug device to
start talking again. At that point the debug controller port reset
will succeed.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
CC: dbrownell@users.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the EHCI debug port is initialized and in use, the EHCI host
controller driver must follow two rules.
1) If the EHCI host driver issues a controller reset, the debug
controller driver re-initialization must get called after the reset
is completed.
2) The EHCI host driver should ignore any requests to the physical
EHCI debug port when the EHCI debug port is in use.
The code to check for the debug port was moved from ehci_pci_reinit()
to ehci_pci_setup because it must get called prior to ehci_reset()
which will clear the debug port registers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: dbrownell@users.sourceforge.net
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements several changes:
1) Improve the capability to debug the dbgp driver
The dbgp_ehci_status() was added in a number of places to report
the critical ehci registers to diagnose the cause of a failure of
the ehci-dbgp driver.
2) Capability to survive the host controller initialization
The dbgp_external_startup(), dbgp_not_safe, and dbgp_phys_port were
added so as to allow the ehci-dbgp to re-initialize after the ehci
host controller is reset by the standard host controller driver.
This same routine is common for the early startup or
re-initialization.
This resulted in the need to move some of the initialization code
out of the __init section because the ehci driver has the
possibility to be loaded later on as a kernel module.
3) Stability improvements for device initialization
The device enumeration from 0 to 127 has the possibility to fail
the first time after a warm reset on some older EHCI debug
controllers. The enumeration will be tried up to 3 times to
account for this failure case.
The dbg_wait_until_complete() was changed to wait up to 250 ms
before failing which only comes into play during device
initialization. The maximum delay will never get hit during the
course of normal operation of the driver, unless the device got
unplugged or there was a ehci controller failure, in which case the
dbgp device driver will shut itself down.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: dbrownell@users.sourceforge.net
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the dbgp early printk driver in advance of refactoring and adding
new code, so the changes to this code are tracked separately from the
move of the code.
The drivers/usb/early directory will be the location of the current
and future early usb code for driving usb devices prior initializing
the standard interrupt driven USB drivers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When do_output_char() attempts to write a carriage return/line feed sequence,
it first checks to see how much buffer room is available. If there are at least
two characters free, it will write the carriage return/line feed with two calls
to tty_put_char(). It calls the tty_operation functions write() for devices that
don't support the tty_operations function put_char(). If the USB generic serial
device's write URB is not in use, it will return the buffer size when asked how
much room is available. The write() of the carriage return will cause it to mark
the write URB busy, so the subsequent write() of the line feed will be ignored.
This patch uses the kfifo infrastructure to implement a write FIFO that
accurately returns the amount of space available in the buffer.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
include/linux/usb/audio.h is exported to userspace,
so part of this file that is for internal kernel
usage need to be guarded with ifdef __KERNEL__.
This way make headers_install will stript it out.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Platform device support was merged earlier, but support for boards to
customize the devflags aspect of the controller was not. We want this on
Blackfin systems to control the bus width, but might as well expose all of
the fields while we're at it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Intel Moorestown EHCI controller supports non-standard HOSTPCx register
extension. This register controls the LPM behaviour and controls the behaviour
of each USB port.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Those functions are used only used to fill the set/get members of
usb_audio_control. It doesn't make much sense to inline them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
linux/usb/audio.h is a public header file that includes definitions
exported to userspace. To avoid namespace clashes, prefix all macro
definitions with UAC_. Existing macros and structures prefixed with
USB_AC_ and USB_AS_ are renamed for consistency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB_SUBCLASS_VENDOR_SPEC is common to several USB classes and as such belongs
to usb/ch9.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And use the new definitions in the USB Audio Class gadget driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various drivers have hacks to mangle termios structures. This stems from
the fact there is no nice setup hook for configuring the termios settings
when the port is created
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And indeed none of them use it. Clean this up as it will make moving to a
standard open method rather easier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To make UVC constants accessible by a future UVC gadget driver, move them from
drivers/media/video/uvc/uvcvideo.h to include/linux/usb/video.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add rx queue pausing to usbnet. This is needed by rndis_wlan so that it can
control rx queue and prevent received packets from being send forward before
rndis_wlan receives and handles 'media connect'-indication. Without this
establishing WPA connections is hard and fail often.
[v2] - removed unneeded use of skb_clone
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add handling for 802.11 specific rndis indications.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow rndis_wlan to see all indications. Currently rndis_host lets rndis_wlan to
know about link state changes only, but there is whole set of other
802.11-specific indications that rndis_wlan should handle properly. So rename
link_change() to indication() and convert rndis_wlan to use it.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wlan devices freeze after running usbnet_stop several times. It appears
that firmware freezes in state where it does not respond to any RNDIS commands
and device have to be physically unplugged/replugged. This patch lets
minidrivers to disable unlink_urbs on usbnet_stop through new info flag.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert the m66592-udc driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_BUILT_IN_M66592 ugliness.
This makes the code cleaner and also allows us to support
both external and internal m66592 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip m66592 without modifying the Kconfig.
The patch adds a m66592 header file for platform data
and ties in platform data to the existing m66592 devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move r8a66597 hardware register definitions from the host
controller header file to the platform data header file.
With this change in place we can easily share register
definitions between the host controller driver and a future
gadget driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the r8a66597-hcd driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_ON_CHIP_R8A66597 ugliness.
This makes the code cleaner and also allows us to support
both external and internal r8a66597 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip r8a66597 without modifying the Kconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit 453f775588.
The driver should not have been accepted as the MSRT code is not
in the main kernel yet, which this depends on.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Hao Wu <hao.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sysrq code acquired a kref leak. Fix it by passing the tty separately
from the caller (thus effectively using the callers kref which all the
callers hold anyway)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow minidriver to know that netdev has stopped. This is to let
wireless turn off radio when usbnet dev is stopped.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that nothing uses the private stats structure we can remove it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Differentiate between SuperSpeed endpoint companion descriptor and the
wireless USB endpoint companion descriptor. Make all structure names for
this descriptor have "ss" (SuperSpeed) in them. David Vrabel asked for
this change in http://marc.info/?l=linux-usb&m=124091465109367&w=2
Reported-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is
supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used
to extend the bus protocol to allow more packets to be sent to an endpoint per
"microframe". The word microframe was removed from the USB 3.0 specification
because the host controller does not send Start Of Frame (SOF) symbols down the
USB 3.0 wires.
The descriptor defines a bMaxBurst field, which indicates the number of packets
of wMaxPacketSize that a SuperSpeed device can send or recieve in a service
interval. All non-control endpoints may set this value as high as 16 packets
(bMaxBurst = 15).
The descriptor also allows isochronous endpoints to further specify that they
can send and receive multiple bursts per service interval. The bmAttributes
allows them to specify a "Mult" of up to 3 (bmAttributes = 2).
Bulk endpoints use bmAttributes to report the number of "Streams" they support.
This was an extension of the endpoint pipe concept to allow multiple mass
storage device commands to be outstanding for one bulk endpoint at a time. This
should allow USB 3.0 mass storage devices to support SCSI command queueing.
Bulk endpoints can say they support up to 2^16 (65,536) streams.
The information in the endpoint companion descriptor must be stored with the
other device, config, interface, and endpoint descriptors because the host
controller needs to access them quickly, and we need to install some default
values if a SuperSpeed device doesn't provide an endpoint companion descriptor.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify the USB core to handle the new USB 3.0 speed, "SuperSpeed". This
is 5.0 Gbps (wire speed). There are probably more places that check for
speed that I've missed.
SuperSpeed devices have a 512 byte endpoint 0 max packet size. This shows
up as a bMaxPacketSize0 set to 0x09 (see table 9-8 of the USB 3.0 bus
spec).
xHCI spec says that the xHC can handle intervals up to 2^15 microframes. That
might change when real silicon becomes available.
Add FIXME note for SuperSpeed isochronous endpoints. They can transmit up
to 16 packets in one "burst" before they wait for an acknowledgment of the
packets. They can do up to 3 bursts per microframe (determined by the
mult value in the endpoint companion descriptor). The xHCI driver doesn't
have support for isoc yet, so fix this later.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Description:
This driver is used for Intel Langwell* USB OTG controller in Intel
Moorestown* platform. It tries to implement host/device role switch
according to OTG spec. The actual hsot and device functions are
accomplished in modified EHCI driver and Intel Langwell USB OTG client
controller driver.
* Langwell and Moorestown are names used in development. They are not
approved official name.
Note:
This patch is the first version Intel Langwell USB OTG Transceiver
driver. The development is not finished, and the bug fixing is on going
for some hardware and software issues. The main purpose of this
submission is for code view.
Supported features:
- Data-line Pulsing SRP
- Support HNP to switch roles
- PCI D0/D3 power management support
Known issues:
- HNP is only tested with another Moorestown platform.
- PCI D0/D3 power management support is not fully tested.
- VBus Pulsing SRP is not support in current version.
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Intel Langwell USB Device Controller is a High-Speed USB OTG device
controller in Intel Moorestown platform. It can work in OTG device mode
with Intel Langwell USB OTG transceiver driver as well as device-only
mode. The number of programmable endpoints is different through
controller revision.
NOTE:
This patch is the first version Intel Langwell USB OTG device controller
driver. The bug fixing is on going for some hardware and software
issues. Intel Langwell USB OTG transceiver driver and EHCI driver
patches will be submitted later.
Supported features:
- USB OTG protocol support with Intel Langwell USB OTG transceiver
driver (turn on CONFIG_USB_LANGWELL_OTG)
- Support control, bulk, interrupt and isochronous endpoints
(isochronous not tested)
- PCI D0/D3 power management support
- Link Power Management (LPM) support
Tested gadget drivers:
- g_file_storage
- g_ether
- g_zero
The passed tests:
- g_file_storage: USBCV Chapter 9 tests
- g_file_storage: USBCV MSC tests
- g_file_storage: from/to host files copying
- g_ether: ping, ftp and scp files from/to host
- Hotplug, with and without hubs
Known issues:
- g_ether: failed part of USBCV chap9 tests
- LPM support not fully tested
TODO:
- g_ether: pass all USBCV chap9 tests
- g_zero: pass usbtest tests
- Stress tests on different gadget drivers
- On-chip private SRAM caching support
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1254) splits up the shutdown method of usb_serial_driver
into a disconnect and a release method.
The problem is that the usb-serial core was calling shutdown during
disconnect handling, but drivers didn't expect it to be called until
after all the open file references had been closed. The result was an
oops when the close method tried to use memory that had been
deallocated by shutdown.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1253) prevents the usb-serial core from calling a
driver's port_probe and port_remove methods more than once per port.
It also removes some unnecessary try_module_get() calls and adds a
missing port_remove method call in a failure path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CPU/board specific parameters (PLL clock, vif etc...) can be set
by platform_data instead of module_param.
v2: remove irq_sense member in platform_data because it can OR in
IRQF_TRIGGER_LOW or IRQF_TRIGGER_FALLING against IORESOURCE_IRQ in
the struct resource.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb_debug driver was modified to implement serial break handling
by using a "magic" data packet comprised of the sequence:
0x00 0xff 0x01 0xfe 0x00 0xfe 0x01 0xff
When the tty layer requests a serial break the usb_debug driver sends
the magic packet. On the receiving side the magic packet is thrown
away or a sysrq is activated depending on what kernel .config options
have been set.
The generic serial driver was modified as well as the usb serial
headers to generically implement sysrq processing in the same way the
non usb uart based drivers implement the sysrq handling. This will
allow other usb serial devices to implement sysrq handling as desired.
The new usb serial functions are named similarly and implemented
similarly to the uart functions as follows:
usb_serial_handle_break <-> uart_handle_break
usb_serial_handle_sysrq_char <-> uart_handle_sysrq_char
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb_debug driver, when used as the console, will always fail to
insert the carriage return and new line sequence as well as randomly
drop console output. This is a result of only having the single
write_urb and that the tty layer will have a lock that prevents the
processing of the back to back urb requests.
The solution is to allow more than one urb to be outstanding and have
a slightly deeper transmit queue. The idea and some code is borrowed
from the ftdi_sio usb driver.
The generic usb serial driver was modified so as to allow the classic
method of 1 write urb, or a multi write urb scheme with N allowed
outstanding urbs where N is controlled by max_in_flight_urbs. When
max_in_flight_urbs in a "struct usb_serial_driver" is non zero the
multi write urb scheme will be used.
The size of 4000 was selected for the usb_debug driver so that the
driver lowers possibility of losing the queued console messages during
the kernel startup.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark internal struct members as /* private: */ so that kernel-doc
won't produce warnings about missing descriptions for them.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The NOP OTG transceiver driver needs to be usable from modules.
Make sure its symbols are always accessible at both compile and
link time, and make sure the device instance is allocated from
the heap so that device lifetime rules are obeyed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
e1000: fix virtualization bug
bonding: fix alb mode locking regression
Bluetooth: Fix issue with sysfs handling for connections
usbnet: CDC EEM support (v5)
tcp: Fix tcp_prequeue() to get correct rto_min value
ehea: fix invalid pointer access
ne2k-pci: Do not register device until initialized.
Subject: [PATCH] br2684: restore net_dev initialization
net: Only store high 16 bits of kernel generated filter priorities
virtio_net: Fix function name typo
virtio_net: Cleanup command queue scatterlist usage
bonding: correct the cleanup in bond_create()
virtio: add missing include to virtio_net.h
smsc95xx: add support for LAN9512 and LAN9514
smsc95xx: configure LED outputs
netconsole: take care of NETDEV_UNREGISTER event
xt_socket: checks for the state of nf_conntrack
bonding: bond_slave_info_query() fix
cxgb3: fixing gcc 4.4 compiler warning: suggest parentheses around operand of ‘!’
netfilter: use likely() in xt_info_rdlock_bh()
...
This introduces a CDC Ethernet Emulation Model (EEM) host side
driver to support USB EEM devices.
EEM is different from the Ethernet Control Model (ECM) currently
supported by the "CDC Ethernet" driver. One key difference is
that it doesn't require of USB interface alternate settings to
manage interface state; some maldesigned hardware can't handle
that part of USB. It also avoids a separate USB interface for
control and status updates.
[ dbrownell@users.sourceforge.net: fix skb leaks, add rx packet
checks, improve fault handling, EEM conformance updates, cleanup ]
Signed-off-by: Omar Laazimani <omar.oberthur@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wessel