The @fnac.net will be shut down within a couple of months, so fix my
email address.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to pass struct ide_port_info also to ide_host_register().
v2:
Fix v5/v6 mismatch noticed by Russell.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The bcount is greater than 0 and less than or equal to 0x10000.
Thus '(bcount & 0xffff) == 0x0000' can be simplified as 'bcount == 0x10000'.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is a port of libata's pata_cs5536.c (written by Martin K. Petersen)
to IDE subsystem.
Changes done while at it:
* Reprogram PIO/MWDMA timings if needed before and after DMA transfer
(chipset uses shared PIO/MWDMA timings).
* Fix cable detection to report 80-wires cable if BIOS set it for any
device on a port (IDE core will do drive-side cable detection later).
* Don't disable UDMA while programming PIO timings.
* Simplify PCI/MSR support.
Pros of having IDE host driver in addition to libata's one:
* IDE is much lighter than SCSI+libata, the host driver itself is also
a bit smaller:
text data bss dec hex filename
1261 496 4 1761 6e1 drivers/ata/pata_cs5536.o
1242 128 4 1374 55e drivers/ide/cs5536.o
* This allows use of IDE features which are unavailable under libata.
v2:
* Fixes per review from Sergei:
- simplify dependency check in Kconfig
- use IDE_DRV_MASK also for ->drive_data
- disable UDMA when programming MWDMA
- program new DTC timings only when necessary
- fix printk() level in cs5536_init_one()
* Fix patch description according to comments from Alan and Sergei.
v3:
* Smarter masking of UDMA bits per Sergei's suggestion.
Cc: Martin K. Petersen <mkp@mkp.net>
Cc: Karl Auerbach <karl@iwl.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The AmigaOne uses the onboard VIA IDE controller in legacy mode (like the
Pegasos).
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On reboot the loop in device_shutdown gets confused by these partially
initialized devices and goes into an infinite loop. Therefore unregister
and disable these devices.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
[bart: remove leftover hwif->present clearing + update patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out port freeing from ide_host_free() to ide_free_port().
* Add ide_disable_port() and use it on ide_register_port() failure.
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC drivers/ide/palm_bk3710.o
drivers/ide/palm_bk3710.c: In function 'palm_bk3710_probe':
drivers/ide/palm_bk3710.c:382: warning: assignment makes integer from pointer without a cast
Someone should fix hw_regs_t to neither be a typedef, nor
use "unsigned long" where it should use "void __iomem *".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[m68k] Falcon IDE: always serialize, in order to force execution of
ide_get_lock() and friends.
Signed-off-By: Michael Schmitz <schmitz@debian.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
[bart: set flag in falconide_port_info instead of falconide_init()]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Monday 12 January 2009, Simon Holm Thøgersen wrote:
> commit 295f000 ("ide: don't execute the next queued command from the
> hard-IRQ context (v2)") breaks suspend to disk for me. On
> 'echo disk > /sys/power/state' the systems hangs, letting me switch
> virtual consoles, but not responding to Alt+SysRq
Restart the request queue early for REQ_TYPE_PM_RESUME requests
(though there is only one resume request for the whole resume
sequence it stays in the queue until is fully completed and now
depends on kblockd for processing consequential resume states).
Reported-and-bisected-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Tested-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CONFIG_LOPEC and CONFIG_SANDPOINT config options are gone.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some rotating disks also present themselves as CFA devices.
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Vortex86SX with IDE controller revision 0x11 ultra DMA must be
disabled. This patch was tested by DMP and seems to work.
It is a cleaned up version of their older Kernel patch:
http://www.dmp.com.tw/tech/vortex86sx/patch-2.6.24-DMP.gz
Tested-by: Shawn Lin <shawn@dmp.com.tw>
Signed-off-by: Brandon Philips <bphilips@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 54cc1428cf ("ide: remove
local_irq_set() macro") accidentally replaced local_save_flags()
by local_irq_set() in ide_probe_port() and __ide_wait_stat()
which resulted in LOCKDEP breakage.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make consistent use of scc_dma_sff_read_status() throughout the driver.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out ide_dma_sff_write_status(), symmetric to ide_dma_sff_read_status().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move apparently misplaced read_sff_dma_status() method from 'struct ide_tp_ops'
to 'struct ide_dma_ops', renaming it to dma_sff_read_status() and making only
required for SFF-8038i compatible IDE controller drivers (greatly cutting down
the number of initializers) as its only user (outside ide-dma-sff.c and such
drivers) appears to be ide_pci_check_simplex() which is only called for such
controllers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace setting of 'hwif->dma_ops' in the 'alim15x3' and 'palm_bk3710' drivers'
init_dma() methods with initializing the corresponding member of their 'struct
ide_port_info' instances and remove such setting from the 'hpt366' driver that
just doesn't use 'sff_dma_ops'. Along with some code save, this prepares us for
the next patch...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Support for the IT8172 IDE controller was removed from the kernel
sometime after 2.6.18. Support for the only boards that used the IT8172
was removed from the kernel after 2.6.18, as they had never compiled
since 2.6.0. However, there are a couple of platforms that use this
chip: the PMC-Sierra Xiao Hu thin-client computer, which is no longer
in production, and the Linksys NSS4000 Network Attached Storage box,
which is based on the Xiao Hu board. I am attempting to add support
for the Xiao Hu to the kernel, and this IT8172 IDE controller is the
first bit of code in this effort.
This patch resurrects the IT8172 IDE controller code. I began with
the 2.6.18 version of the it8172.c file, and have moved it forward so
that it works with the latest version of the kernel. I have run this
driver on a PMC-Sierra Xiao Hu board with the 2.6.28 kernel, and
I have had no problems with it in my configuration. The attached patch
applies cleanly against 2.6.28.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: alan@lxorguk.ukuu.org.uk
[bart: s/HWIF(drive)/drive->hwif/]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This makes ide_port_scan()'s behavior match ide_host_register()'s
one and fixes OOPS in elv_may_queue() during port re-scan.
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ->cur_dev should now be always valid if ->handler is set so
remove redundant checks from ide_intr() and ide_timer_expiry().
* Apply CodingStyle fixups in ide_timer_expiry() while at it.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->handler is set while it shouldn't be it indicates deep problems
so BUG_ON()-ning and preventing further damage is much more appropriate
than merely printing an error message.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... and remove no longer needed cdrom_start_packet_command and
cdrom_transfer_packet_command.
Tested lightly with ide-cd and ide-floppy.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
as it is done for all other IDE ATAPI devices.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... instead of assuming it is set for accelerated DRQ type devices.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According the documentation, id[ATA_ID_DWORD_IO] is non-zero if
the drive supports dword IO, while the code disables support by
setting IDE_DFLAG_NO_IO_32BIT. In addition, this word has been
reused by the ATA8 specification. This patch fixes both cases.
Signed-off-by: Mario Schwalbe <schwalbe@inf.tu-dresden.de>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove id[ATA_ID_DWORD_IO] check altogether per Sergei's suggestion]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_port_for_each_dev() / ide_host_for_each_port() iterators
and update IDE code to use them.
While at it:
- s/unit/i/ variable in ide_port_wait_ready(), ide_probe_port(),
ide_port_tune_devices(), ide_port_init_devices_data(), do_reset1(),
ide_acpi_set_state() and scc_dma_end()
- s/d/i/ variable in ide_proc_port_register_devices()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Allocate device structures dynamically instead of having them embedded
in ide_hwif_t:
* Remove needless zeroing of port structure from ide_init_port_data().
* Add ide_hwif_t.devices[MAX_DRIVES] (table of pointers to the devices).
* Add ide_port_{alloc,free}_devices() helpers and use them respectively
in ide_{host,free}_alloc().
* Convert all users of ->drives[] to use ->devices[] instead.
While at it:
* Use drive->dn for the slave device check in scc_pata.c.
As a nice side-effect this patch cuts ~1kB (x86-32) from the resulting
code size:
text data bss dec hex filename
53963 1244 237 55444 d894 drivers/ide/ide-core.o.before
52981 1244 237 54462 d4be drivers/ide/ide-core.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Because presence of the peer device was not checked in
it821x_set_pio_mode() PIO0 mode was used for taskfile PIO
in single device configurations.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove (now superfluous) ->error method from struct ide_driver.
* Unexport __ide_error() and make it static.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- s/struct ide_driver_s/struct ide_driver/
- use to_ide_driver() macro in ide-proc.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Just use u8 instead, also s/__u8/u8/ in ide-cd.h while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Samuel Thibault