According to commit 659fb32d1b
("replace irq_gc_ack() with {set,clr}_bit variants"), this
should be fixed.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since commit 8560a6cfc9
"arm: Footbridge: Use common i8253 clockevent",
ARCH_NETWINDER needs to select CLKEVT_I8253.
This patch fixes below build error with "make netwinder_defconfig".
LD .tmp_vmlinux1
arch/arm/mach-footbridge/built-in.o: In function `isa_timer_init':
isa-rtc.c:(.init.text+0x12c8): undefined reference to `clockevent_i8253_init'
isa-rtc.c:(.init.text+0x12d0): undefined reference to `i8253_clockevent'
arch/arm/mach-footbridge/built-in.o:(.data+0x198): undefined reference to `i8253_clockevent'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is a workaround for the 364296 ARM1136 r0p2 erratum (possible
cache data corruption with hit-under-miss enabled). It sets the
undocumented bit 31 in the auxiliary control register and the FI bit in
the control register, thus disabling hit-under-miss without putting the
processor into full low interrupt latency mode.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes L2 Cache size calculations for L2C-210, L2C-310 and
PL310, by changing the L2X0_AUX_CTRL_WAY_SIZE_MASK from 2 bits to 3
bits.
The Auxiliary Control Register for L2C-210, L2C-310 and PL310 has 3bits
[19:17] for Way size, however the existing code only uses 2 bits to
get this value. This results in incorrect cachesize calculations.
It also results in performing operations on the whole cache when we
erroneously decide that the range is big enough (due to l2x0_size being
too small) and also prints incorrect cachesize.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the obvious error in board detection logic, because according to the TS's
manual, the model is stored in the least three significant bits. For example
the byte read on my ts-7300 is 0x23 and the detection then fails.
Cc: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (32 commits)
ARM: mmp: Change the way we use timer 0 as clockevent timer.
ARM: mmp: Switch to using timer 1 as clocksource timer.
ARM: mmp: Also start timer 1 on boot.
ARM: pxa168/gplugd: free correct GPIO
ARM: pxa168/gplugd: get rid of mfp-gplugd.h
ARM: pxa: fix logic error in PJ4 iWMMXt handling
mach-sa1100: fix PCI build problem
omap: timer: Set dmtimer used as clocksource in autoreload mode
OMAP3: am3517crane: remove NULL board_mux from board file
arm: mach-omap2: mux: use kstrdup()
arch:arm:plat-omap:iovmm: remove unused variable 'va'
Update Nook Color machine 3284 to common Encore name
am3505/3517: Various platform defines for UART4
OMAP: hwmod: fix build break on non-OMAP4 multi-OMAP2 builds
OMAP: Fix linking error in twl-common.c for OMAP2/3/4 only builds
iMX: Fix build for iMX53
ARM: mx5: board-cpuimx51.c fixup irq_to_gpio() usage
OMAP2+: PM: SmartReflex: use put_sync_suspend for IRQ-safe disabling
OMAP3: beagle: don't touch omap_device internals
OMAP1: enable GENERIC_IRQ_CHIP
...
The current cache detection code does not check for an aliasing
I-cache if the D-cache is found to be VIPT aliasing.
This patch fixes the problem by always checking for an aliasing
I-cache on v6 and later.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The smp_twd clockevents driver currently enables the local timer PPI
before the clockevents device is registered. This can lead to a kernel
panic if a spurious timer interrupt is generated before registration
has completed since the kernel will treat it as an IPI timer.
This patch moves the clockevents device registration before the IRQ
unmasking so that we can always handle timer interrupts once they can
occur.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The various reset routines in mach-realview rely on an FPGA to
power-cycle the board after writing some magic runes to memory-mapped
registers.
This patch adds a dsb() following the writes, so that they become
visible before we mdelay(1000) in the arch_reset code. Without this
patch, the timeout would expire sporadically, causing the reset to fail.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit f12482c9 ("ARM: 6974/1: pmu: refactor reservation") changed
{release,reserve}_pmu to take an enum arm_pmu_type as a parameter, but
inconsistently named the parameter `type' or `device'. It would be nice
if these were consistent.
This patch makes use of enum arm_pmu_type consistent, always using
`type'. Related printks are updated, explicitly mentioning `type' also.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit f12482c9 ("ARM: 6974/1: pmu: refactor reservation") changed the
prototype of release_pmu, but missed the stub for when
CONFIG_CPU_HAS_PMU is not selected by the platform.
This patch changes the prototype of the stub, preventing possible build
failures when CONFIG_CPU_HAS_PMU is not selected.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Instead of setting up a match interrupt for 'current_time + delta'
on ->set_next_event(), program timer 0 to count down from 'delta - 1'
and trigger an interrupt when it reaches zero.
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Currently, arch-mmp/time.c uses timer 0 both as a clocksource timer
and as a clockevent timer, the latter by setting up a comparator
interrupt to match on 'current_time + delta'. This is problematic
if delta is small enough, as that can lead to 'current_time + delta'
already being in the past when comparator setup has finished, leading
to the requested event not triggering.
As there is also a silicon issue that requires stopping a timer's
counter while writing to one of its match registers, we'll switch to
using two separate timers -- timer 0 as clockevent timer, which we'll
start and stop on every invocation of ->set_next_event(), and timer 1
as clocksource timer, which will be free-running.
This first patch enables timer 1 on boot, so that we can use it as
clocksource timer.
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Move definitions from mfp-gplugd.h to mfp-pxa168.h as they aren't
gplugD specific.
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: drop experimental status for ARM_PATCH_PHYS_VIRT
ARM: 7008/1: alignment: Make SIGBUS sent to userspace POSIXly correct
ARM: 7007/1: alignment: Prevent ignoring of faults with ARMv6 unaligned access model
ARM: 7010/1: mm: fix invalid loop for poison_init_mem
ARM: 7005/1: freshen up mm/proc-arm946.S
dmaengine: PL08x: Fix trivial build error
ARM: Fix build error for SMP=n builds
The PCI nanoengine driver in the SA1100 machine probably has not
been building for some time. It probably dragged hardware.h
in implicitly and now it doesn't anymore. After this an SA1100
build selecting all system variants will build successfully.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If CONFIG_OMAP_32K_TIMER is not selected and dmtimer is used as clocksource, the
timer stops counting once overflow occurs as it was not set in autoreload mode.
This results into timekeeping failure: for example, 'sleep 1' at the shell after
the timer counter overflow would hang.
This patch sets up autoreload when starting the clocksource timer which fixes
the above issue.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since 7203f8a48b (arm: mach-omap2: remove
NULL board_mux from board files) NULL board_mux is defined in mux.h.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use kstrdup rather than duplicating its implementation
The semantic patch that makes this output is available
in scripts/coccinelle/api/kstrdup.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pointer "va" returned from "phys_to_virt(pa)" is never used in
"sgtable_fill_kmalloc()".So,it is safe to remove this set-but-unused variable.
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing definitions for the AM3505/3517 UART4 such
as DMAs, INTs and base address.
Signed-of-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This has now been well tested, and several platforms are now selecting
this directly. It's time to drop its experimental status.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Builds for multi-OMAP2 (e.g., OMAP2420 with OMAP2430) with
CONFIG_ARCH_OMAP4=n fail with the following errors:
arch/arm/mach-omap2/built-in.o: In function `_enable_module':
arch/arm/mach-omap2/omap_hwmod.c:701: undefined reference to `omap4_cminst_module_enable'
arch/arm/mach-omap2/built-in.o: In function `_disable_module':
arch/arm/mach-omap2/omap_hwmod.c:726: undefined reference to `omap4_cminst_module_disable'
arch/arm/mach-omap2/built-in.o: In function `_wait_target_disable':
arch/arm/mach-omap2/omap_hwmod.c:1179: undefined reference to `omap4_cminst_wait_module_idle'
This is probably due to the preprocessor directives in
arch/arm/plat-omap/include/plat/cpu.h that convert some cpu_is_omap*()
expressions from preprocessor directives into something that is only
resolvable during runtime, if multiple OMAP2 build targets are
selected.
Thanks to Tony Lindgren <tony@atomide.com> for reporting.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit b22f954 (OMAP4: Move common twl6030 configuration to twl-common)
caused compile failures for code for OMAP arch which is not selected by
the config.
Fixes issues like:
With CONFIG_ARCH_OMAP3=y and CONFIG_ARCH_OMAP4=n, I'm getting this:
arch/arm/mach-omap2/built-in.o:(.data+0xf99c): undefined reference to `omap4430_phy_init'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a0): undefined reference to `omap4430_phy_exit'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a4): undefined reference to `omap4430_phy_power'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a8): undefined reference to `omap4430_phy_set_clk'
arch/arm/mach-omap2/built-in.o:(.data+0xf9ac): undefined reference to `omap4430_phy_suspend'
Fix the problem by moving the code to ifdef sections for omap3 and omap4.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the UM_SIGNAL alignment fault mode, no siginfo structure is
passed to userspace.
POSIX specifies how siginfo_t should be populated for alignment
faults, so this patch does just that:
* si_signo = SIGBUS
* si_code = BUS_ADRALN
* si_addr = misaligned data address at which access was attempted
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, it's possible to set the kernel to ignore alignment
faults when changing the alignment fault handling mode at runtime
via /proc/sys/alignment, even though this is undesirable on ARMv6
and above, where it can result in infinite spins where an un-fixed-
up instruction repeatedly faults.
In addition, the kernel clobbers any alignment mode specified on
the command-line if running on ARMv6 or above.
This patch factors out the necessary safety check into a couple of
new helper functions, and checks and modifies the fault handling
mode as appropriate on boot and on writes to /proc/cpu/alignment.
Prior to ARMv6, the behaviour is unchanged.
For ARMv6 and above, the behaviour changes as follows:
* Attempting to ignore faults on ARMv6 results in the mode being
forced to UM_FIXUP instead. A warning is printed if this
happened as a result of a write to /proc/cpu/alignment. The
user's UM_WARN bit (if present) is still honoured.
* An alignment= argument from the kernel command-line is now
honoured, except that the kernel will modify the specified mode
as described above. This is allows modes such as UM_SIGNAL and
UM_WARN to be active immediately from boot, which is useful for
debugging purposes.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
poison_init_mem() used a loop of:
while ((count = count - 4))
which has 2 problems - an off by one error so that we do one less word
than we should, and the other is that if count == 0 then we loop forever
and poison too much. On a platform with HAVE_TCM=y but nothing in the
TCM's, this caused corruption and the platform failed to boot.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The file mm/proc-arm946.S contains a typo and is missing a structure
member in __arm946_proc_info. The former prevents compilation
and the latter causes problems during boot. It is likely this
file was manually copied from a similar file and not tested, then
later updates to the *_proc_info structures missed this file.
This patch will apply (with offset) with or without the
recent macro unification work that has been done in this directory.
This was verified against linux-next/stable last week.
See arm-linux-kernel thread:
http://lists.arm.linux.org.uk/lurker/message/20110718.103237.0106d468.en.html
Signed-off-by: Brian S. Julin <bri@abrij.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch use channel0 as Tx, and channel1 as Rx
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This corrects a logic-error that I made in the original implementation.
An alternate patch would be to just remove these lines and
leave the clock running as it is reconfigured later on during
boot anyway.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit fad107086d fixed the wrong test for MX51
as the MX51 addresses are wrong for MX50 and MX53 but now it's MX51 only,
UART_PADDR is not defined anymore when building for MX50/MX53.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Steev Klimaszewski <steev@genesi-usa.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
irq_to_gpio() is being called on a GPIO so change to using
gpio_to_irq() instead.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The generic library code already exports the generic function, this was
left-over from the ARM-specific version that just got removed.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 1eb19a12bd ("lib/sha1: use the git implementation of
SHA-1"), the ARM SHA1 routines no longer work. The reason? They
depended on the larger 320-byte workspace, and now the sha1 workspace is
just 16 words (64 bytes). So the assembly version would overwrite the
stack randomly.
The optimized asm version is also probably slower than the new improved
C version, so there's no reason to keep it around. At least that was
the case in git, where what appears to be the same assembly language
version was removed two years ago because the optimized C BLK_SHA1 code
was faster.
Reported-and-tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
omap_sr_disable_reset_volt is called with irqs off in omapx_enter_sleep,
as part of idle sequence, this eventually calls sr_disable and
pm_runtime_put_sync. pm_runtime_put_sync calls rpm_idle, which will
enable interrupts in order to call the callback. In this short interval
when interrupts are enabled, scenarios such as the following can occur:
while interrupts are enabled, the timer interrupt that is supposed to
wake the device out of idle occurs and is acked, so when the CPU finally
goes to off, the timer is already gone, missing a wakeup event.
Further, as the documentation for runtime states:"
However, subsystems can use the pm_runtime_irq_safe() helper function
to tell the PM core that a device's ->runtime_suspend() and ->runtime_resume()
callbacks should be invoked in atomic context with interrupts disabled
(->runtime_idle() is still invoked the default way)."
Hence, replace pm_runtime_put_sync with pm_runtime_put_sync_suspend
to invoke the suspend handler and shut off the fclk for SmartReflex
module instead of using the idle handler in interrupt disabled context.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Colin Cross <ccross@google.com>
[khilman@ti.com: minor Subject edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
Board code should not touch omap_device internals. To get the MPU/IVA devices,
use existing APIs: omap2_get_mpu_device(), omap2_get_iva_device().
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP1 needs this also since GPIO driver (common for all OMAPs) is
being converted to use generic IRQ chip.
Signed-off-by: Kevin Hilman <khilman@ti.com>
SmartReflex should be disabled while entering low power mode due to
a) SmartReflex values are not defined for retention voltage, further
b) with SmartReflex enabled, if CPU enters lower c-states, FSM will try
to bump the voltage to current OPP's voltage for which it has entered c-state;
hence SmartReflex needs to be disabled for MPU, CORE and IVA voltage
domains in idle path before enabling auto retention voltage achievement
on the device.
However, since the current pm_runtime setup for SmartReflex devices are
setup to allow callbacks to be invoked with interrupts enabled, calling
SmartReflex enable/disable from other contexts such as idle paths
where preemption is disabled causes warnings such as the following
indicating of a potential race.
[ 82.023895] [<c04d079c>] (__irq_svc+0x3c/0x120) from [<c04d0484>] (_raw_spin_unlock_irq+0x28/0x2c)
[ 82.023895] [<c04d0484>] (_raw_spin_unlock_irq+0x28/0x2c) from [<c0323234>] (rpm_callback+0x4c/0x68)
[ 82.023956] [<c0323234>] (rpm_callback+0x4c/0x68) from [<c0323f7c>] (rpm_resume+0x338/0x53c)
[ 82.023956] [<c0323f7c>] (rpm_resume+0x338/0x53c) from [<c03243f4>] (__pm_runtime_resume+0x48/0x60)
[ 82.023986] [<c03243f4>] (__pm_runtime_resume+0x48/0x60) from [<c008aee0>] (sr_enable+0xa8/0x19c)
[ 82.023986] [<c008aee0>] (sr_enable+0xa8/0x19c) from [<c008b2fc>] (omap_sr_enable+0x50/0x90)
[ 82.024017] [<c008b2fc>] (omap_sr_enable+0x50/0x90) from [<c00888c0>] (omap4_enter_sleep+0x138/0x168)
Instead, we use pm_runtime_irq_safe to tell the PM core that callbacks can be
invoked in interrupt disabled contexts.
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
CONFIG_PM is no longer a user-selectable Kconfig option. Rather it is
automatically enabled if either CONFIG_SUSPEND or CONFIG_RUNTIME_PM is
enabled, so having a 'select PM' here is redunant when 'select
CONFIG_PM_RUNTIME' is present.
Signed-off-by: Kevin Hilman <khilman@ti.com>
If the DPLL is already enabled, don't try to enable it again.
Since write to the DPLL control register will make the DPLL
reset and which will cause some issues when some child module
are sourced from this DPLL.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit a0bfa13738 mispells
cpuidle_idle_call() on ARM and SH code. Fix this to be consistent.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: x86@kernel.org
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
[ Also done by Mark Brown - th ebug has been around forever, and was
noticed in -next, but the idle tree never picked it up. Bad bad bad ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
cpuidle: stop depending on pm_idle
x86 idle: move mwait_idle_with_hints() to where it is used
cpuidle: replace xen access to x86 pm_idle and default_idle
cpuidle: create bootparam "cpuidle.off=1"
mrst_pmu: driver for Intel Moorestown Power Management Unit
Unfortunately, the module fixups cause the kernel to fail to build
when SMP is not enabled. Fix this by removing the reference to
fixup_smp on non-SMP fixup kernels, but ensuring that if we do have
the SMP fixup section, we refuse to load the module.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cpuidle users should call cpuidle_call_idle() directly
rather than via (pm_idle)() function pointer.
Architecture may choose to continue using (pm_idle)(),
but cpuidle need not depend on it:
my_arch_cpu_idle()
...
if(cpuidle_call_idle())
pm_idle();
cc: Kevin Hilman <khilman@deeprootsystems.com>
cc: Paul Mundt <lethal@linux-sh.org>
cc: x86@kernel.org
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Migrate the driver for the v7-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I810db5b50b71cdca4e869aa0d0310f7f48781a55
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Migrate the driver for the v6-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I03ba597b95b4d62b42da112a8efac88d67aa40f9
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
No need to have a separate header file containing only register
definitions that are used by a single driver. Fold these into the
gpio driver.
Signed-off-by: David Brown <davidb@codeaurora.org>
The gpiomux.h header contains some SOC ifdefs. However, the API that
is actually used by the GPIO driver only uses two functions that are
general. Move these general definitions into a public header file.
Change-Id: Ia5df8af87dba268225598d56908e523bcfc24ef6
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Select the GPIO register configuration at runtime rather than through
idefs.
Change-Id: I02ea0a3d61bc81669f32097c32420f0688552231
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Put an SOC prefix on each GPIO register definition, eliminating the
need to have SOC ifdefs around the definitions.
Change-Id: I5a01fd328a89ce1be610847934d6e118f5465e42
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The two GPIO controllers are always mapped to the same virtual address
across all MSM devices. Instead of selecting this at compile time,
determine the physical address at runtime, eliminating yet something
else preventing multiple MSM targets from being compiled into the same
kernel.
Change-Id: I1672219d978ab6243526adeda6badf49472baa27
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The MSM7x25 and MSM7x27 devices are not yet supported in the kernel.
Remove #ifdef-based tables supporting these chips for now.
Change-Id: I4d9f5abc4cc0942ce75a067097b072489493c1b8
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Request for comment and commit.
From: T. Mehnert <t.mehnert@eckelmann.de>
Date: Mon, 4 Jul 2011 15:53:30 +0200
Subject: [PATCH] i.MX25 GPT clock fix: ensure correct the clock source
This patch ensures, that Linux will take the correct clock source (AHB_DIV)
for gpt in the ARM i.MX25 implementation. The currect code depends on the reset
defaults of the CCM_MCR register. So on some boards it could happen that the
UPLL is used for clock source, which results in faulty time behavior in Linux.
In this case all delays or sleeps will will be faktor 1.8 too long.
Signed-off-by: Torsten Mehnert <t.mehnert@eckelmann.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
* 'at91/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
at91: add arch specific ioremap support
at91: factorize sram init
at91: move register clocks to soc generic init
at91: move clock subsystem init to soc generic init
at91: use structure to store the current soc
at91: remove AT91_DBGU offset from dbgu register macro
at91: factorize at91 interrupts init to soc
at91: introduce commom AT91_BASE_SYS
* 'next/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (21 commits)
arm/dt: tegra devicetree support
arm/versatile: Add device tree support
dt/irq: add irq_domain_generate_simple() helper
irq: add irq_domain translation infrastructure
dmaengine: imx-sdma: add device tree probe support
dmaengine: imx-sdma: sdma_get_firmware does not need to copy fw_name
dmaengine: imx-sdma: use platform_device_id to identify sdma version
mmc: sdhci-esdhc-imx: add device tree probe support
mmc: sdhci-pltfm: dt device does not pass parent to sdhci_alloc_host
mmc: sdhci-esdhc-imx: get rid of the uses of cpu_is_mx()
mmc: sdhci-esdhc-imx: do not reference platform data after probe
mmc: sdhci-esdhc-imx: extend card_detect and write_protect support for mx5
net/fec: add device tree probe support
net: ibm_newemac: convert it to use of_get_phy_mode
dt/net: add helper function of_get_phy_mode
net/fec: gasket needs to be enabled for some i.mx
serial/imx: add device tree probe support
serial/imx: get rid of the uses of cpu_is_mx1()
arm/dt: Add dtb make rule
arm/dt: Add skeleton dtsi file
...
My previous commit left the file empty and present in the
Makefile, which is a bit dirty and caused problems with
'make distclean', as pointed out by David Howells.
This hopefully cleans it up the right way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: John Linn <john.linn@xilinx.com>
instead of reading the registers everytime
the current implementation respect the following constrain:
- allow 1 to n soc to be enabled
- allow to have a virtual cpu type and subtype
- always detect the cpu type and subtype and report it
- detect if the soc support is enabled
- prepare for sysfs export support
- drop soc specific code via compiler when the soc not enabled
(via cpu_is_xxx)
Today if we read the exid we will have the same value for 9g35 and 9m11
and we will need to check the cidr too
with the new implementation we just need to check the soc subtype
this will also allow to have specific virtual subtype for rm9200 which the
board will have to specify via at91rm9200_set_type(int) as we have no way to
detect it.
this implementation is inspired by the SH cpu detection support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
they are the same except the default priority
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
On all at91 except rm9200 and x40 have the System Controller starts
at address 0xffffc000 and has a size of 16KiB.
On rm9200 it's start at 0xfffe4000 of 111KiB with non reserved data starting
at 0xfffff000
This patch removes the individual definitions of AT91_BASE_SYS and
replaces them with a common version at base 0xfffffc000 and size 16KiB
and map the same memory space
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Everything required to populate NVIDIA Tegra devices from the device
tree. This patch adds a new DT_MACHINE_DESC() which matches against
a tegra20 device tree. So far it only registers the on-chip devices,
but it will be refined in follow on patches to configure clocks and
pin IO from the device tree also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For testing the dt work, define a dt-enabled versatile platform.
This patch adds a new versatile platform for when using the device
tree. Add platform and amba devices are discovered and registered by
parsing the device tree. Clocks and initial io mappings are still
configured statically.
This patch still depends on some static platform_data for a few devices
which is passed via the auxdata structure to of_platform_populate(),
but it is a viable starting point until the drivers can get all
configuration data out of the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds irq_domain infrastructure for translating from
hardware irq numbers to linux irqs. This is particularly important
for architectures adding device tree support because the current
implementation (excluding PowerPC and SPARC) cannot handle
translation for more than a single interrupt controller. irq_domain
supports device tree translation for any number of interrupt
controllers.
This patch converts x86, Microblaze, ARM and MIPS to use irq_domain
for device tree irq translation. x86 is untested beyond compiling it,
irq_domain is enabled for MIPS and Microblaze, but the old behaviour is
preserved until the core code is modified to actually register an
irq_domain yet. On ARM it works and is required for much of the new
ARM device tree board support.
PowerPC has /not/ been converted to use this new infrastructure. It
is still missing some features before it can replace the virq
infrastructure already in powerpc (see documentation on
irq_domain_map/unmap for details). Followup patches will add the
missing pieces and migrate PowerPC to use irq_domain.
SPARC has its own method of managing interrupts from the device tree
and is unaffected by this change.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Now that v4l2 subdevices have got their own device objects, having
one more device in soc-camera clients became redundant and confusing.
This patch removes those devices and the soc-camera bus, they used to
reside on.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This moves us one more step closer to eliminating the soc-camera bus
and devices on it. Besides, as a side effect, CSI-2 runtime PM on
sh-mobile secomes finer grained now: we only have to power on the
interface, when the device nodes are open.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The RX-51 uses the CSIb IO complex for camera operation. The
board file is missing definition for the regulator supplying
the CSIb complex, so this is added for better power
management.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It might be not good to use software defined version to identify sdma
device type, when hardware does not define such version. Instead,
soc name is stable enough to define the device type.
The patch uses platform_device_id rather than version number passed
by platform data to identify sdma device type/version.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>
The patch removes all the uses of cpu_is_mx(). Instead, it utilizes
platform_device_id to distinguish the esdhc differences among SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
The patch extends card_detect and write_protect support to get mx5
family and more scenarios supported. The changes include:
* Turn platform_data from optional to mandatory
* Add cd_types and wp_types into platform_data to cover more use
cases
* Remove the use of flag ESDHC_FLAG_GPIO_FOR_CD
* Adjust some machine codes to adopt the platform_data changes
* Work around the issue that software reset will get card detection
circuit stop working
With this patch, card_detect and write_protect gets supported on
mx5 based platforms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Chris Ball <cjb@laptop.org>
On the recent i.mx (mx25/50/53), there is a gasket inside fec
controller which needs to be enabled no matter phy works in MII
or RMII mode.
The current code enables the gasket only when phy interface is RMII.
It's broken when the driver works with a MII phy. The patch uses
platform_device_id to distinguish the SoCs that have the gasket and
enables it on these SoCs for both MII and RMII mode.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reported-by: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
The patch removes all the uses of cpu_is_mx1(). Instead, it uses
the .id_table of platform_driver to distinguish the uart device type,
IMX1_UART and IMX21_UART. The IMX21_UART type runs on all i.mx
except i.mx1.
A couple of !cpu_is_mx1 logic gets turned into is_imx21_uart,
as the codes wrapped there are really IMX21 type uart specific.
It also removes macro MX1_UCR3_REF25 and MX1_UCR3_REF30 which are
not used anywhere.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
* 'next/board' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: S3C64XX: Configure backup battery charger on Cragganmore
ARM: S3C64XX: Fix WM8915 IRQ polarity on Cragganmore
ARM: S3C64XX: Configure supplies for all Cragganmore regulators
ARM: S3C64XX: Refresh Cragganmore support
ARM: S3C64XX: Initial support for Wolfson/Simtec Cragganmore/Banff
OMAP4: Keyboard: Mux changes in the board file
omap: blaze: add mmc5/wl1283 device support
omap: 4430SDP: Register the card detect GPIO properly
arm: omap3: cm-t35: add support for cm-t3730
OMAP3: beagle: add support for beagleboard xM revision C
OMAP3: rx-51: Add full regulator definitions
omap: rx51: Platform support for lp5523 led chip
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
* 'next/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
MAINTAINERS: add maintainer of CSR SiRFprimaII machine
ARM: CSR: initializing L2 cache
ARM: CSR: mapping early DEBUG_LL uart
ARM: CSR: Adding CSR SiRFprimaII board support
OMAP4: clocks: Update the clock tree with 4460 clock nodes
OMAP4: PRCM: OMAP4460 specific PRM and CM register bitshifts
OMAP4: ID: add omap_has_feature for max freq supported
OMAP: ID: introduce chip detection for OMAP4460
ARM: Xilinx: merge board file into main platform code
ARM: Xilinx: Adding Xilinx board support
Fix up conflicts in arch/arm/mach-omap2/cm-regbits-44xx.h
After changing all consumers of atomics to include <linux/atomic.h>, we
ran into some compile time errors due to this dependency chain:
linux/atomic.h
-> asm/atomic.h
-> asm-generic/atomic-long.h
where atomic-long.h could use funcs defined later in linux/atomic.h
without a prototype. This patches moves the code that includes
asm-generic/atomic*.h to linux/atomic.h.
Archs that need <asm-generic/atomic64.h> need to select
CONFIG_GENERIC_ATOMIC64 from now on (some of them used to include it
unconditionally).
Compile tested on i386 and x86_64 with allnoconfig.
Signed-off-by: Arun Sharma <asharma@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is in preparation for more generic atomic primitives based on
__atomic_add_unless.
Signed-off-by: Arun Sharma <asharma@fb.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The majority of architectures implement ext2 atomic bitops as
test_and_{set,clear}_bit() without spinlock.
This adds this type of generic implementation in ext2-atomic-setbit.h and
use it wherever possible.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Andreas Dilger <adilger@dilger.ca>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On MX51 Babbage board the RTS/CTS pins are not used on UART2 port.
Fix the registration of this port.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code is assuming that gpio_get_value() is returning 0 or 1 but it
should be checking if the value is 0 or not. Not doing it properly is breaking
the detection of the board (and thus the reboot of efika mx to2) when using
the new mxc gpio driver, which relies on basic mmio gpio.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While testing the keys, I only checked that the key were generating an input
event but unfortunately, they were not generating the right event. Fix that.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mx51_initialize_usb_hw() support introduced a small error. The usbh1 has
pdev->id equal to 1 not 0, so use pdev->id to make things less error-prone and
to fix that.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
I2C signals SDA/SCL are a bit different, they need to be pull-up and
open-drain (so to support multiple I2C devices).
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix the following section mismatches:
WARNING: vmlinux.o(.text+0x1026c): Section mismatch in reference from the function lilly1131_usb_init() to the variable .init.rodata:imx31_mxc_ehci_hs_data
The function lilly1131_usb_init() references
the variable __initconst imx31_mxc_ehci_hs_data.
This is often because lilly1131_usb_init lacks a __initconst
annotation or the annotation of imx31_mxc_ehci_hs_data is wrong.
WARNING: vmlinux.o(.text+0x10270): Section mismatch in reference from the function lilly1131_usb_init() to the (unknown reference) .init.rodata:(unknown)
The function lilly1131_usb_init() references
the (unknown reference) __initconst (unknown).
This is often because lilly1131_usb_init lacks a __initconst
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.text+0x10274): Section mismatch in reference from the function lilly1131_usb_init() to the (unknown reference) .init.data:(unknown)
The function lilly1131_usb_init() references
the (unknown reference) __initdata (unknown).
This is often because lilly1131_usb_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix the following section mismatches:
WARNING: vmlinux.o(.text+0x101cc): Section mismatch in reference from the function mxc_init_i2c() to the (unknown reference) .init.data:(unknown)
The function mxc_init_i2c() references
the (unknown reference) __initdata (unknown).
This is often because mxc_init_i2c lacks a __initdata
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.text+0x101d8): Section mismatch in reference from the function mxc_init_i2c() to the variable .init.rodata:imx31_imx_i2c_data
The function mxc_init_i2c() references
the variable __initconst imx31_imx_i2c_data.
This is often because mxc_init_i2c lacks a __initconst
annotation or the annotation of imx31_imx_i2c_data is wrong.
WARNING: vmlinux.o(.text+0x10200): Section mismatch in reference from the function mxc_init_audio() to the variable .init.rodata:imx31_imx_ssi_data
The function mxc_init_audio() references
the variable __initconst imx31_imx_ssi_data.
This is often because mxc_init_audio lacks a __initconst
annotation or the annotation of imx31_imx_ssi_data is wrong.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without this platform data the aic32x4 audio
codec in the Visstrim_M10 won't work properly.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (741 commits)
staging:iio:meter:ade7753 should be 16 bit read not 8 bit for mode register.
staging:iio:kfifo_buf fix double initialization of the ring device structure.
staging:iio:accel:lis3l02dq: fix incorrect pointer passed to spi_set_drvdata.
staging:iio:imu fix missing register table index for some channels
spectra: enable device before poking it
staging: rts_pstor: Fix a miswriting
staging/lirc_bt829: Return -ENODEV when no hardware is found.
staging/lirc_parallel: remove pointless prototypes.
staging/lirc_parallel: fix panic on rmmod
staging:iio:adc:ad7476: Incorrect pointer into spi_set_drvdata.
Staging: zram: Fix kunmapping order
Revert "gma500: Fix dependencies"
gma500: Add medfield header
gma500: wire up the mrst i2c bus from chip_info
gma500: Fix DPU build
gma500: Clean up the DPU config and make it runtime
gma500: resync with Medfield progress
gma500: Use the mrst helpers and power control for mode commit
gma500@ Fix backlight range error
gma500: More Moorestown muddle meddling means MM maybe might modeset
...
Fix up fairly trivial conflicts all over, mostly due to header file
cleanup conflicts, but some deleted files and some just context changes:
- Documentation/feature-removal-schedule.txt
- drivers/staging/bcm/headers.h
- drivers/staging/brcm80211/brcmfmac/dhd_linux.c
- drivers/staging/brcm80211/brcmfmac/dhd_sdio.c
- drivers/staging/brcm80211/brcmfmac/wl_cfg80211.h
- drivers/staging/brcm80211/brcmfmac/wl_iw.c
- drivers/staging/et131x/et131x_netdev.c
- drivers/staging/rtl8187se/ieee80211/ieee80211_softmac.c
- drivers/staging/rtl8192e/r8192E.h
- drivers/staging/usbip/userspace/src/utils.h
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (115 commits)
EHCI: fix direction handling for interrupt data toggles
USB: serial: add IDs for WinChipHead USB->RS232 adapter
USB: OHCI: fix another regression for NVIDIA controllers
usb: gadget: m66592-udc: add pullup function
usb: gadget: m66592-udc: add function for external controller
usb: gadget: r8a66597-udc: add pullup function
usb: renesas_usbhs: support multi driver
usb: renesas_usbhs: inaccessible pipe is not an error
usb: renesas_usbhs: care buff alignment when dma handler
USB: PL2303: correctly handle baudrates above 115200
usb: r8a66597-hcd: fixup USB_PORT_STAT_C_SUSPEND shift
usb: renesas_usbhs: compile/config are rescued
usb: renesas_usbhs: fixup comment-out
usb: update email address in ohci-sh and r8a66597-hcd
usb: r8a66597-hcd: add function for external controller
EHCI: only power off port if over-current is active
USB: mon: Allow to use usbmon without debugfs
USB: EHCI: go back to using the system clock for QH unlinks
ehci: add pci quirk for Ordissimo and RM Slate 100 too
ehci: refactor pci quirk to use standard dmi_check_system method
...
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
From: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
platform data for simple backlight driver for LM3530
in the u5500 platform
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: take the ACL checks to common code
bury posix_acl_..._masq() variants
kill boilerplates around posix_acl_create_masq()
generic_acl: no need to clone acl just to push it to set_cached_acl()
kill boilerplate around posix_acl_chmod_masq()
reiserfs: cache negative ACLs for v1 stat format
xfs: cache negative ACLs if there is no attribute fork
9p: do no return 0 from ->check_acl without actually checking
vfs: move ACL cache lookup into generic code
CIFS: Fix oops while mounting with prefixpath
xfs: Fix wrong return value of xfs_file_aio_write
fix devtmpfs race
caam: don't pass bogus S_IFCHR to debugfs_create_...()
get rid of create_proc_entry() abuses - proc_mkdir() is there for purpose
asus-wmi: ->is_visible() can't return negative
fix jffs2 ACLs on big-endian with 16bit mode_t
9p: close ACL leaks
ocfs2_init_acl(): fix a leak
VFS : mount lock scalability for internal mounts
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
ARM: S3C24XX: Use generic s3c_set_platdata for devices
ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
ARM: SAMSUNG: Use generic s3c_set_platdata for FB
ARM: SAMSUNG: Use generic s3c_set_platdata for TS
ARM: S3C64XX: Add PWM backlight support on SMDK6410
ARM: S5P64X0: Add PWM backlight support on SMDK6450
ARM: S5P64X0: Add PWM backlight support on SMDK6440
ARM: S5PC100: Add PWM backlight support on SMDKC100
ARM: S5PV210: Add PWM backlight support on SMDKV210
ARM: EXYNOS4: Add PWM backlight support on SMDKC210
ARM: EXYNOS4: Add PWM backlight support on SMDKV310
ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
...
Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
Add a make rule to compile dt blobs for ARM.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Tested-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds a DT_MACHINE_START macro to use instead of
MACHINE_START when creating a machine_desc that supports using the
device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SDHI block on the ag5evm requires waiting for idle
before writing to some registers.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initialize get_context_loss_count in the DSS board data to
omap_pm_get_dev_context_loss_count, so that omapdss driver can use it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function to get device's context loss count has changed from
omap_pm_get_last_off_on_transaction_id() to
omap_pm_get_dev_context_loss_count()
Change name of the function pointer in omapdss.h accordingly, and use
the term "context loss count" instead of "context id" in the code.
Restructure the context loss count functions to handle errors properly,
and ensure that context is always considered lost if an error happens.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] s5pv210: make needlessly global symbols static
[CPUFREQ] exynos4210: make needlessly global symbols static
[CPUFREQ] S3C6410: Add some lower frequencies for 800MHz base clock operation
[CPUFREQ] S5PV210: Add reboot notifier to prevent system hang
[CPUFREQ] S5PV210: Adjust udelay prior to voltage scaling down
[CPUFREQ] S5PV210: Lock a mutex while changing the cpu frequency
[CPUFREQ] S5PV210: Add pm_notifier to prevent system unstable
[CPUFREQ] S5PV210: Add arm/int voltage control support
[CPUFREQ] S5PV210: Add additional symantics for "relation" in cpufreq with pm
[CPUFREQ] S3C64xx: Notify transition complete as soon as frequency changed
[CPUFREQ] S3C6410: Support 800MHz operation in cpufreq
[CPUFREQ] s5pv210-cpufreq.c: Add missing clk_put
[CPUFREQ] Move compile for S3C64XX cpufreq to /drivers/cpufreq
[CPUFREQ] Remove some vi noise that escaped into the Makefile.
[CPUFREQ] Move ARM Samsung cpufreq drivers to drivers/cpufreq/
[CPUFREQ/S3C64xx] Move S3C64xx CPUfreq driver into drivers/cpufreq
[CPUFREQ] Handle CPUs with different capabilities in acpi-cpufreq
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
This patch removes all the module loader hook implementations in the
architecture specific code where the functionality is the same as that
now provided by the recently added default hooks.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
* 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mips: Fix i8253 clockevent fallout
i8253: Cleanup outb/inb magic
arm: Footbridge: Use common i8253 clockevent
mips: Use common i8253 clockevent
x86: Use common i8253 clockevent
i8253: Create common clockevent implementation
i8253: Export i8253_lock unconditionally
pcpskr: MIPS: Make config dependencies finer grained
pcspkr: Cleanup Kconfig dependencies
i8253: Move remaining content and delete asm/i8253.h
i8253: Consolidate definitions of PIT_LATCH
x86: i8253: Consolidate definitions of global_clock_event
i8253: Alpha, PowerPC: Remove unused asm/8253pit.h
alpha: i8253: Cleanup remaining users of i8253pit.h
i8253: Remove I8253_LOCK config
i8253: Make pcsp sound driver use the shared i8253_lock
i8253: Make pcspkr input driver use the shared i8253_lock
i8253: Consolidate all kernel definitions of i8253_lock
i8253: Unify all kernel declarations of i8253_lock
i8253: Create linux/i8253.h and use it in all 8253 related files
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (123 commits)
perf: Remove the nmi parameter from the oprofile_perf backend
x86, perf: Make copy_from_user_nmi() a library function
perf: Remove perf_event_attr::type check
x86, perf: P4 PMU - Fix typos in comments and style cleanup
perf tools: Make test use the preset debugfs path
perf tools: Add automated tests for events parsing
perf tools: De-opt the parse_events function
perf script: Fix display of IP address for non-callchain path
perf tools: Fix endian conversion reading event attr from file header
perf tools: Add missing 'node' alias to the hw_cache[] array
perf probe: Support adding probes on offline kernel modules
perf probe: Add probed module in front of function
perf probe: Introduce debuginfo to encapsulate dwarf information
perf-probe: Move dwarf library routines to dwarf-aux.{c, h}
perf probe: Remove redundant dwarf functions
perf probe: Move strtailcmp to string.c
perf probe: Rename DIE_FIND_CB_FOUND to DIE_FIND_CB_END
tracing/kprobe: Update symbol reference when loading module
tracing/kprobes: Support module init function probing
kprobes: Return -ENOENT if probe point doesn't exist
...
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
iommu/core: Fix build with INTR_REMAP=y && CONFIG_DMAR=n
iommu/amd: Don't use MSI address range for DMA addresses
iommu/amd: Move missing parts to drivers/iommu
iommu: Move iommu Kconfig entries to submenu
x86/ia64: intel-iommu: move to drivers/iommu/
x86: amd_iommu: move to drivers/iommu/
msm: iommu: move to drivers/iommu/
drivers: iommu: move to a dedicated folder
x86/amd-iommu: Store device alias as dev_data pointer
x86/amd-iommu: Search for existind dev_data before allocting a new one
x86/amd-iommu: Allow dev_data->alias to be NULL
x86/amd-iommu: Use only dev_data in low-level domain attach/detach functions
x86/amd-iommu: Use only dev_data for dte and iotlb flushing routines
x86/amd-iommu: Store ATS state in dev_data
x86/amd-iommu: Store devid in dev_data
x86/amd-iommu: Introduce global dev_data_list
x86/amd-iommu: Remove redundant device_flush_dte() calls
iommu-api: Add missing header file
Fix up trivial conflicts (independent additions close to each other) in
drivers/Makefile and include/linux/pci.h
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (51 commits)
PM: Improve error code of pm_notifier_call_chain()
PM: Add "RTC" to PM trace time stamps to avoid confusion
PM / Suspend: Export suspend_set_ops, suspend_valid_only_mem
PM / Suspend: Add .suspend_again() callback to suspend_ops
PM / OPP: Introduce function to free cpufreq table
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
...
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/imx: add device tree probe support
spi/imx: copy gpio number passed by platform data into driver private data
spi/imx: use soc name in spi device type naming scheme
spi/imx: merge type SPI_IMX_VER_0_7 into SPI_IMX_VER_0_4
spi/imx: do not use spi_imx2_3 to name SPI_IMX_VER_2_3 function and macro
spi/imx: use mx21 to name SPI_IMX_VER_0_0 function and macro
spi/imx: do not make copy of spi_imx_devtype_data
spi/dw: Add spi number into spi irq desc
spi/tegra: Use engineering names in DT compatible property
spi/fsl_spi: fix CPM spi driver
mach-s3c2410: remove unused spi-gpio.h file
spi: remove obsolete spi-s3c24xx-gpio driver
mach-gta2: remove unused spi-gpio.h include
mach-qt2410: convert to spi_gpio
mach-jive: convert to spi_gpio
spi/pxa2xx: Remove unavailable ssp_type from documentation
spi/bfin_spi: uninline fat queue funcs
spi/bfin_spi: constify pin array
spi/bfin_spi: use structs for accessing hardware regs
spi/topcliff-pch: Support new device ML7223 IOH
...
Fix up trivial conflict in arch/arm/mach-ep93xx/Makefile
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1287 commits)
icmp: Fix regression in nexthop resolution during replies.
net: Fix ppc64 BPF JIT dependencies.
acenic: include NET_SKB_PAD headroom to incoming skbs
ixgbe: convert to ndo_fix_features
ixgbe: only enable WoL for magic packet by default
ixgbe: remove ifdef check for non-existent define
ixgbe: Pass staterr instead of re-reading status and error bits from descriptor
ixgbe: Move interrupt related values out of ring and into q_vector
ixgbe: add structure for containing RX/TX rings to q_vector
ixgbe: inline the ixgbe_maybe_stop_tx function
ixgbe: Update ATR to use recorded TX queues instead of CPU for routing
igb: Fix for DH89xxCC near end loopback test
e1000: always call e1000_check_for_link() on e1000_ce4100 MACs.
netxen: add fw version compatibility check
be2net: request native mode each time the card is reset
ipv4: Constrain UFO fragment sizes to multiples of 8 bytes
virtio_net: Fix panic in virtnet_remove
ipv6: make fragment identifications less predictable
ipv6: unshare inetpeers
can: make function can_get_bittiming static
...
Kukjin Kim