HMT support is currently broken and needs to be reworked to play nicely
with the SMT scheduler. Remove the bit rotten bits for the time being.
I also updated an incorrect comment, we enter __secondary_hold with the
physical cpu id in r3.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The runlatch SPR can take a lot of time to write. My original runlatch
code would set it on every exception entry even though most of the time
this was not required. It would also continually set it in the idle
loop, which is an issue on an SMT capable processor.
Now we cache the runlatch value in a threadinfo bit, and only check for
it in decrementer and hardware interrupt exceptions as well as the idle
loop. Boot on POWER3, POWER5 and iseries, and compile tested on pmac32.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For UP to SMP kexec to work we need to jump into pSeries_secondary_smp_init
event on a UP + KEXEC kernel. The secondary cpus will not find their hw_cpu_id
in the paca and so they'll jump into kexec_wait, ready for a kexec.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since 404849bbd2 we've been using
LOAD_REG_ADDRBASE, which uses the toc pointer, in decrementer_iSeries_masked.
This can explode if we take the decrementer interrupt while we're in a module,
because the toc pointer in r2 will be the module's toc pointer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present the lppaca - the structure shared with the iSeries
hypervisor and phyp - is contained within the PACA, our own low-level
per-cpu structure. This doesn't have to be so, the patch below
removes it, making a separate array of lppaca structures.
This saves approximately 500*NR_CPUS bytes of image size and kernel
memory, because we don't need aligning gap between the Linux and
hypervisor portions of every PACA. On the other hand it means an
extra level of dereference in many accesses to the lppaca.
The patch also gets rid of several places where we assign the paca
address to a local variable for no particular reason.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch consolidates the variety of macros used for loading 32 or
64-bit constants in assembler (LOADADDR, LOADBASE, SET_REG_TO_*). The
idea is to make the set of macros consistent across 32 and 64 bit and
to make it more obvious which is the appropriate one to use in a given
situation. The new macros and their semantics are described in the
comments in ppc_asm.h.
In the process, we change several places that were unnecessarily using
immediate loads on ppc64 to use the GOT/TOC. Likewise we cleanup a
couple of places where we were clumsily subtracting PAGE_OFFSET with
asm instructions to use assemble-time arithmetic or the toreal() macro
instead.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't set CONFIG_PPC_MULTIPLATFORM on iSeries (yet). Avoid
compiling in the prom_init stuff on iSeries.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove a comment in head.S which is no longer relevant.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a few places where we need to fix things up for the kernel to work
if it's linked at 32MB:
- platforms/powermac/smp.c
To start secondary cpus on pmac we patch the reset vector, which is fine.
Except if we're above 32MB we don't have enough bits for an absolute branch,
it needs to relative.
- kernel/head_64.s
- A few branches in the cpu hold code need to load the full target address
and do a bctr.
- after_prom_start needs to load PHYSICAL_START as the dest address, not 0.
- The exception prolog needs to load the low word of the target adddress,
not just the low halfword.
- Fixup handling of the initial stab address.
- kernel/setup_64.c
smp_release_cpus() needs to write 1 to the spinloop flag near 0, not 32 MB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The fwnmi vectors can be anywhere < 32 MB, so we need to use a trampoline
for them. The kdump kernel will register the trampoline addresses, which will
then jump up to the real code above 32 MB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes several unnecessary fields from the paca:
- next_jiffy_update_tb was simply unused. Remove trivially.
- The exdsi exception save area was not used. There were plans to use
it, but they never seem to have gone anywhere. If they ever do, we
can put it back. Remove from the paca, and from asm-offsets.c
- The default_decr field was used from asm, but was only ever assigned
the value of tb_ticks_per_jiffy. Just access tb_ticks_per_jiffy from
asm directly instead.
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges platform codes. systemcfg->platform is no longer used,
systemcfg use in general is deprecated as much as possible (and renamed
_systemcfg before it gets completely moved elsewhere in a future patch),
_machine is now used on ppc64 along as ppc32. Platform codes aren't gone
yet but we are getting a step closer. A bunch of asm code in head[_64].S
is also turned into C code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds a new CONFIG_PPC_64K_PAGES which, when enabled, changes the kernel
base page size to 64K. The resulting kernel still boots on any
hardware. On current machines with 4K pages support only, the kernel
will maintain 16 "subpages" for each 64K page transparently.
Note that while real 64K capable HW has been tested, the current patch
will not enable it yet as such hardware is not released yet, and I'm
still verifying with the firmware architects the proper to get the
information from the newer hypervisors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no reason for smp_release_cpus() to be asm, and most people can make
more sense of C code. Add an extern declaration to smp.h and remove the custom
one in machine_kexec.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This brings in a lot of changes from arch/ppc64/kernel/pmac_*.c to
arch/powerpc/platforms/powermac/*.c and makes various minor tweaks
elsewhere. On the powermac we now initialize ppc_md by copying
the whole pmac_md structure into it, which required some changes in
the ordering of initializations of individual fields of it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge ppc32 and ppc64 versions of thread_info.h. They were pretty
similar already, the chief changes are:
- Instead of inline asm to implement current_thread_info(),
which needs to be different for ppc32 and ppc64, we use C with an
asm("r1") register variable. gcc turns it into the same asm as we
used to have for both platforms.
- We replace ppc32's 'local_flags' with the ppc64
'syscall_noerror' field. The noerror flag was in fact the only thing
in the local_flags field anyway, so the ppc64 approach is simpler, and
means we only need a load-immediate/store instead of load/mask/store
when clearing the flag.
- In readiness for 64k pages, when THREAD_SIZE will be less
than a page, ppc64 used kmalloc() rather than get_free_pages() to
allocate the kernel stack. With this patch we do the same for ppc32,
since there's no strong reason not to.
- For ppc64, we no longer export THREAD_SHIFT and THREAD_SIZE
via asm-offsets, thread_info.h can now be safely included in asm, as
on ppc32.
Built and booted on G4 Powerbook (ARCH=ppc and ARCH=powerpc) and
Power5 (ARCH=ppc64 and ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a bunch of mostly small fixes that are needed to get
ARCH=powerpc to compile for 64-bit. This adds setup_64.c from
arch/ppc64/kernel/setup.c and locks.c from arch/ppc64/lib/locks.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Although both ppc32 and ppc64 have a reloc_offset function, the ppc64
one produced the opposite sign to the ppc32 one. This standardizes
on the ppc32 sign and fixes the merged 64-bit code to account for that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes symbols like HID0, SPRG3, SRR0, SRR1 etc. that refer to
special purpose registers to SPRN_HID0, SPRN_SPRG3, etc. Using the
SPRN_ symbols clutters the namespace less, and the forthcoming merge
of asm/processor.h and asm/reg.h is going to remove the non-SPRN_
versions.
Signed-off-by: Paul Mackerras <paulus@samba.org>
These macros help in writing assembly code that works for both ppc32
and ppc64. With this we now have a common fpu.S. This takes out
load_up_fpu from head_64.S.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Anton Blanchard