If a QP has separate send and receive CQs, then the send CQ will never
have receive completions from that QP in it. So when cleaning the
send CQ, there's no need to pass in an SRQ pointer, even if the QP is
attached to an SRQ.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Trigger device remove and then add when a catastrophic error is
detected in hardware. This, in turn, will cause a device reset, which
we hope will recover from the catastrophic condition.
Since this might interefere with debugging the root cause, add a
module option to suppress this behaviour.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Modifications to the existing rdma header files, core files, drivers,
and ulp files to support iWARP, including:
- Hook iWARP CM into the build system and use it in rdma_cm.
- Convert enum ib_node_type to enum rdma_node_type, which includes
the possibility of RDMA_NODE_RNIC, and update everything for this.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove some trailing whitespace that has snuck in despite the best
efforts of whitespace=error-all. Also fix a few other whitespace
bogosities.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Incorrect number of bits was taken for static_rate field.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
port_num was not being returned for unconnected QPs.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When default static rate is returned for Tavor, need to translate it
to an ib rate value.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Pass a struct ib_udata to the low-level driver's ->modify_srq() and
->modify_qp() methods, so that it can get to the device-specific data
passed in by the userspace driver.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make kernel use UAR2 instead of UAR1 for hardware access: this adds
sanity checking from the hardware side, without any performance cost.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The SM LID used to send traps to is incorrectly set to port LID. This
is a regression from 2.6.17 -- after a PortInfo MAD is received, no
traps are sent to the SM LID. The traps go to the loopback interface
instead, and are dropped there. The SM LID should be taken from the
sm_lid of the PortInfo response.
The bug was introduced by commit 12bbb2b7be7f5564952ebe0196623e97464b8ac5:
IB/mthca: Add client reregister event generation
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It is supposed to be OK to call mthca_create_ah() and mthca_destroy_ah()
from any context. However, for mem-full HCAs, these functions use the
mthca_alloc() and mthca_free() bitmap helpers, and those helpers use
non-IRQ-safe spin_lock() internally. Lockdep correctly warns that
this could lead to a deadlock. Fix this by changing mthca_alloc() and
mthca_free() to use spin_lock_irqsave().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Update the driver's list of HCA firmware revisions to make sure people
running Sinai firmware older than 1.1.0 get a message suggesting a
firmware upgrade. Update the Arbel versions as well while we are at it.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Leave all SRQ methods out of the device's uverbs_cmd_mask if the
device doesn't have SRQ support (because of ancient firmware) so that
we don't allow userspace to call the driver's create_srq method. This
fixes a userspace-triggerable oops caused by ib_uverbs_create_srq()
following the device's ->create_srq function pointer, which will be
NULL if the device doesn't support SRQs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When destroying a QP, mthca locks both the QP's send CQ and receive
CQ. However, the following scenario is perfectly valid:
QP_a: send_cq == CQ_x, recv_cq == CQ_y
QP_b: send_cq == CQ_y, recv_cq == CQ_x
The old mthca code simply locked send_cq and then recv_cq, which in
this case could lead to an AB-BA deadlock if QP_a and QP_b were
destroyed simultaneously.
We can fix this by changing the locking code to lock the CQ with the
lower CQ number first, which will create a consistent lock ordering.
Also, the second CQ is locked with spin_lock_nested() to tell lockdep
that we know what we're doing with the lock nesting.
This bug was found by lockdep.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The fence bit needs to be set in the doorbell too, not just the WQE.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Define a constant MTHCA_ARRAY_MASK to replace repeated uses of
(PAGE_SIZE / sizeof (void *) - 1) in mthca array code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_array_clear() does not clear the slot if the used count is
positive. This leads to crashes in mthca_qp_event() since that uses
mthca_array_get() to check that the qp is valid.
Discovered by Ali Ayoub.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Read the max_cmds value from the response to the QUERY_FW command
before printing out the value, so that the real value goes into the
debug output.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Mem-free HCAs always keep one spare SRQ WQE, so the SRQ limit cannot
be set beyond srq->max - 1.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After recent changes, mthca_wq_init does not actually initialize the WQ as it
used to - it simply resets all index fields to their initial values. So,
let's rename it to mthca_wq_reset.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Acked-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mthca_ah_query returs the static rate of the address handle in internal mthc
format. fix it to use rate encoding from enum ib_rate, which is what users
expect.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mthca: initialize send and receive queue locks separately
lockdep identifies a lock by the call site of its initialization. By
initializing the send and receive queue locks in mthca_wq_init() we confuse
lockdep. It warns that that the ordered acquiry of both locks in
mthca_modify_qp() is recursive acquiry of one lock:
=============================================
[ INFO: possible recursive locking detected ]
---------------------------------------------
modprobe/1192 is trying to acquire lock:
(&wq->lock){....}, at: [<f892b4db>] mthca_modify_qp+0x60/0xa7b [ib_mthca]
but task is already holding lock:
(&wq->lock){....}, at: [<f892b4ce>] mthca_modify_qp+0x53/0xa7b [ib_mthca]
Initializing the locks separately in mthca_alloc_qp_common() stops the
warning and will let lockdep enforce proper ordering on paths that acquire
both locks.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/infiniband/core_locking.txt says:
All of the methods in struct ib_device exported by a low-level
driver must be fully reentrant. The low-level driver is required to
perform all synchronization necessary to maintain consistency, even
if multiple function calls using the same object are run
simultaneously.
However, mthca's modify_qp, modify_srq and resize_cq methods are
currently not reentrant. Add a mutex to the QP, SRQ and CQ structures
so that these calls can be properly serialized.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some error paths after the mthca_alloc_mailbox() call in mthca_modify_qp()
just do a "return -EINVAL" without freeing the mailbox. Convert these
returns to "goto out" to avoid leaking the mailbox storage.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Report the true max_map_per_fmr value from mthca_query_device(),
taking into account the change in FMR remapping introduced by the
Sinai performance optimization.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change the mthca snoop of MADs that set PortInfo to check if the SM
has set the client reregister bit, and if it has, generate a client
reregister event. If the bit is not set, just generate a LID change
event as usual.
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The kernel has had wait_for_completion_timeout() for a long time now.
mthca should use it to handle FW commands timing out, instead of
implementing the same thing in a much more complicated way by using
wait_for_completion() along with a timer that does complete().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Memfree firmware is in rare cases reporting WQE index == base - 1 in
receive completion with error, instead of (rq size - 1); base is 0 in
mthca. Here is a patch to avoid kernel crash and report a correct WR
id in this case.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca does not restore the following PCI-X/PCI Express registers after reset:
PCI-X device: PCI-X command register
PCI-X bridge: upstream and downstream split transaction registers
PCI Express : PCI Express device control and link control registers
This causes instability and/or bad performance on systems where one of
these registers is set to a non-default value by BIOS.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If we post a list of length exactly a multiple of 256, nreq in
doorbell gets set to 256 which is wrong: it should be encoded by 0.
This is because we only zero it out on the next WR, which may not be
there. The solution is to ring the doorbell after posting a WQE, not
before posting the next one.
This is the same bug that we just fixed for QPs with non-shared RQ.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If we post a list of length 256 exactly, nreq in doorbell gets set to
256 which is wrong: it should be encoded by 0. This is because we
only zero it out on the next WR, which may not be there. The solution
is to ring the doorbell after posting a WQE, not before posting the
next one.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Setting fw_cmd_doorbell allows FW command to be queued using posted
writes instead of requiring polling on a "go" bit, so it should be a
performance boost. However, the option causes problems with at least
some device/firmware combinations, so set the default to 0 until we
understand what's going on better.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Addresses for ioremap must be calculated off of pci_resource_start;
we can't directly use the bus address as seen by the HCA. Fix the
code that remaps device memory for FMR access.
Based on patch by Klaus Smolin.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix races in in destroying various objects. If a destroy routine
waits for an object to become free by doing
wait_event(&obj->wait, !atomic_read(&obj->refcount));
/* now clean up and destroy the object */
and another place drops a reference to the object by doing
if (atomic_dec_and_test(&obj->refcount))
wake_up(&obj->wait);
then this is susceptible to a race where the wait_event() and final
freeing of the object occur between the atomic_dec_and_test() and the
wake_up(). And this is a use-after-free, since wake_up() will be
called on part of the already-freed object.
Fix this in mthca by replacing the atomic_t refcounts with plain old
integers protected by a spinlock. This makes it possible to do the
decrement of the reference count and the wake_up() so that it appears
as a single atomic operation to the code waiting on the wait queue.
While touching this code, also simplify mthca_cq_clean(): the CQ being
cleaned cannot go away, because it still has a QP attached to it. So
there's no reason to be paranoid and look up the CQ by number; it's
perfectly safe to use the pointer that the callers already have.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
GuidInfo records have 8 byte GUIDs in them, so an index should be
multiplied by 8 to get an offset. mthca_query_gid() was incorrectly
multiplying by 16.
Noticed by Leonid Keller <leonid@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes the needlessly global mthca_update_rate() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver allocates SRQ WQEs size with a power of 2 size both for
Tavor and for memfree. For Tavor, however, the hardware only requires
the WQE size to be a multiple of 16, not a power of 2, and the max
number of scatter-gather allowed is reported accordingly by the
firmware (and this is the value currently returned by
ib_query_device() and ibv_query_device()).
If the max number of scatter/gather entries reported by the FW is used
when creating an SRQ, the creation will fail for Tavor, since the
required WQE size will be increased to the next power of 2, which
turns out to be larger than the device permitted max WQE size (which
is not a power of 2).
This patch reduces the reported SRQ max wqe size so that it can be used
successfully in creating an SRQ on Tavor HCAs.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PCI spec recommends against drivers playing with a device's PCI
read burst size, and says that systems software should configure it.
And we actually have users that report that changing it from the
default set by BIOS hurts performance and/or stability for them. On
the other hand, the Mellanox Programmer's Reference Manual recommends
turning it up all the way to the maximum value. Some tests conducted
here in the lab do not show performance improvement from this tuning,
but this might be just me.
As a work-around, make this tuning an option, off by default (safe
value), with an eye towards removing it completely one day if no one
complains.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Push translation of static rate to HCA format into low-level drivers,
where it belongs. For static rate encoding, use encoding of rate
field from IB standard PathRecord, with addition of value 0, for
backwards compatibility with current usage. The changes are:
- Add enum ib_rate to midlayer includes.
- Get rid of static rate translation in IPoIB; just use static rate
directly from Path and MulticastGroup records.
- Update mthca driver to translate absolute static rate into the
format used by hardware. This also fixes mthca's static rate
handling for HCAs that are capable of 4X DDR.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change the mthca debugging trace output code so that it can enabled
and disabled at runtime with the debug_level module parameter in
sysfs. Also, don't allow CONFIG_INFINIBAND_MTHCA_DEBUG to be disabled
unless CONFIG_EMBEDDED is selected. We want users (and especially
distros) to have this turned on unless they really need to save space,
because by the time we want debugging output, it's usually too late to
rebuild a kernel.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Quite a few cleanup functions in mthca were marked as __devexit.
However, they could also be called from error paths during
initialization, so they cannot be marked that way. Just delete all of
the incorrect annotations.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The previous patch for Tavor broke MemFree logic.
The driver should perform limit check only for Tavor. For MemFree,
the check is incorrect, since ds (WQE stride) is always a power-of-2
(although the max_desc_size may not be).
In Tavor, however, WQE stride and desc_size are the same, and are not
necessarily power-of-2. The check was really for the WQE stride (and
it Tavor, we use max_desc_size for the stride).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the call to mthca_MODIFY_QP() failed, then mthca_modify_qp() would
still do some things it shouldn't, such as store away attributes for
special QPs. Fix this, and simplify the code, by simply jumping to
the exit path if mthca_MODIFY_QP() fails.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_alloc_sqp() by mthca_set_qp_size() need to set qp->transport
before calling mthca_set_qp_size(), since the value is used there.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When setting the shared receive queue (SRQ) watermark in a modify SRQ
operation, make sure that the supplied value is not larger than the
full size of the SRQ.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Guarantee the calculated work queue entry size does not exceed the max
allowable WQE size when creating an SRQ. This is a problem with Arbel
in Tavor-compatibility mode because the current WQE size computation
method rounds up to next power of 2.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a check that the modify QP parameters sgid_index and path_mtu are
valid, since they might come from userspace.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix endianness handling of srq_limit: it is big-endian in the context
structure, so we need to swab it before returning it.
Also add support for srq_limit query for Tavor (non-MemFree) HCAs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
MemFree devices need to reserve one shared receive queue (SRQ) work
request for internal use, so the capacity returned from the create_srq
and query_srq methods should be srq->max - 1.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix bug found by coverity: the loop body never executed, because it
was doing for (i = 0; i < MTHCA_EQ_CMD; ++i), but MTHCA_EQ_CMD is 0.
The correct loop bound is MTHCA_NUM_EQ, to loop over all EQs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Sinai (one-port PCI Express) HCAs get improved throughput for messages
bigger than 80 KB in DDR mode if memory keys are formatted in a
specific way. The enhancement only works if the memory key table is
smaller than 2^24 entries. For larger tables, the enhancement is off
and a warning is printed (to avoid silent performance loss).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use a named enum for the HCA's internal page size, rather than having
magic values of 4096 and shifts by 12 all over the code. Also, fix
one minor bug in EQ handling: only one HCA page is mapped to the HCA
during initialization, but a full kernel page is unmapped during
cleanup. This might cause problems when PAGE_SIZE != 4096.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check that the alternate P_Key index is in range when setting the
alternate path for a QP. Also make a cosmetic touch up to the debug
message printed when the main P_Key index is out of range.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for IB_SEND_FENCE flag in post_send methods.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement query_ah (except for AVs which are in HCA memory). This is
needed to implement RMPP duplicate session detection on sending side
(extraction of DGID/DLID and GRH flag from address handle).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch is checks whether the HCA supports posting FW commands
through a doorbell page (user access region 0, or "UAR0"). If this is
supported, the driver maps UAR0 and uses it for FW commands. This can
be controlled by the value of a writable module parameter
fw_cmd_doorbell. When the parameter is 0, the commands are posted
through HCR using the old method; otherwise if HCA is capable commands
go through UAR0.
This use of UAR0 to post commands eliminates the need for polling the
"go" bit prior to posting a new command. Since reading from a PCI
device is much more expensive then issuing a posted write, it is
expected that issuing FW commands this way will provide better CPU
utilization.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Have mthca's create_srq method return the actual capacity of the SRQ
that gets created. Also update comments in <rdma/ib_verbs.h> to
clarify that this is what is expected from ib_create_srq().
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use ib_modify_qp_is_ok() in mthca, and delete the big table of
attributes for queue pair state transitions.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add low-level driver support to ib_mthca so that consumers can request
a "send queue drained" event be generated when a transiton to the SQD
state completes.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch allows the consumer to set the page size of "pages" mapped
by the pool FMRs, which is a feature already existing in the base
verbs API. On the cosmetic side it changes ib_fmr_attr.page_size field
to be named page_shift.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a modify_device method to mthca, which implements setting the node
description. This makes the writable "node_desc" sysfs attribute work
for Mellanox HCAs.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The might_sleep() annotations in mthca are silly -- they all occur
shortly before calls that will end up in core functions like kmalloc()
that will print the same warning in an unsafe context anyway. In
fact, beyond cluttering the source, we're actually bloating text with
CONFIG_DEBUG_SPINLOCK_SLEEP and/or CONFIG_PREEMPT_VOLUNTARY set.
With both options set, getting rid of the might_sleep()s saves a lot:
add/remove: 0/0 grow/shrink: 0/7 up/down: 0/-171 (-171)
function old new delta
mthca_pd_alloc 132 109 -23
mthca_init_cq 969 946 -23
mthca_mr_alloc 592 568 -24
mthca_pd_free 67 42 -25
mthca_free_mr 219 194 -25
mthca_free_cq 570 545 -25
mthca_fmr_alloc 742 716 -26
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The function mthca_free_err_wqe() can never fail, so get rid of its
return value. That means handle_error_cqe() doesn't have to check
what mthca_free_err_wqe() returns, which means it can't fail either
and doesn't have to return anything either. All this results in
simpler source code and a slight object code improvement:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-10 (-10)
function old new delta
mthca_free_err_wqe 83 81 -2
mthca_poll_cq 1758 1750 -8
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When debugging is enabled, the mthca_QUERY_DEV_LIM() firmware command
function prints out some of the device limits that it queries.
However the debugging prints happen before all of the fields are
extracted from the firmware response, so some of the values that get
printed are uninitialized junk. Move the prints to the end of the
function to fix this.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert semaphores to mutexes in mthca. Leave firmware command
interface poll_sem and event_sem as semaphores.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have run into the following problem: if a task receives a signal
while in the process of e.g. destroying a resource (which could be
because the relevant file was closed) mthca could bail out from trying
to take a command interface semaphore without performing the
appropriate command to tell hardware that the resource is being
destroyed.
As a result we see messages like
ib_mthca 0000:04:00.0: HW2SW_CQ failed (-4)
In this case, hardware could access the resource after the memory has
been freed, possibly causing memory corruption.
A simple solution is to replace down_interruptible() by down() in
command interface activation.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
[ It's also not safe to bail out on multicast table operations, since
they may be invoked on the cleanup path too. So use down() for
mcg_table.sem too. ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are some cards around that have UAR (user access region) size
different from 8 MB. Relax our sanity check to make sure that the PCI
BAR is big enough to access the UAR size reported by the device
firmware instead.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_create_ah() includes the port number in the GID index. The reverse
needs to be done in mthca_read_ah().
Noted by Hal Rosenstock.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
build_mlx_header() was using sqp->ud_header.grh_present before it was
initialized by mthca_read_ah(). Furthermore, header->grh_present is
set by ib_ud_header_init, so there's no need to set it again in
mthca_read_ah().
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the ALIGN macro to simplify some rounding code.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix memory leaks in mthca_create_qp() and mthca_create_srq()
error handling.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert "/ (1 << lg)" to ">> lg" for a slight code size reduction.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-24 (-24)
function old new delta
mthca_map_cmd 613 589 -24
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a node_guid field to struct ib_device. It is the responsibility
of the low-level driver to initialize this field before registering a
device with the midlayer. Convert everyone to looking at this field
instead of calling ib_query_device() when all they want is the node
GUID, and remove the node_guid field from struct ib_device_attr.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out common code for initializing MAD packets, which is shared
by many query routines in mthca_provider.c, into init_query_mad().
add/remove: 1/0 grow/shrink: 0/4 up/down: 16/-44 (-28)
function old new delta
init_query_mad - 16 +16
mthca_query_port 521 518 -3
mthca_query_pkey 301 294 -7
mthca_query_device 648 641 -7
mthca_query_gid 453 426 -27
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I am seeing EQ overruns in SDP stress tests: if the CQ completion
handler arms a CQ, this could generate more EQEs, so that EQ will
never get empty and consumer index will never get updated.
This is similiar to what we have with command interface:
/*
* cmd_event() may add more commands.
* The card will think the queue has overflowed if
* we don't tell it we've been processing events.
*/
However, for completion events, we *don't* want to update the consumer
index on each event. So, perform EQ doorbell coalescing: allocate EQs
with some spare EQEs, and update once we run out of them.
The value 0x80 was selected to avoid any performance impact.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For all pages except possibly the last one, the byte beyond the buffer
end must be page aligned. Therefore, when computing the page shift to
use, OR the end addresses of the buffers as well as the start
addresses into the mask we check.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add code to modify QP operation to handle setting alternate paths for
connected QPs.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fill vendor_err field in completion with error.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Multicast group management fixes:
. Fix leak of mailbox memory in error handling on multicast group operations.
. Free AMGM indices at detach and in attach error handling.
. Fix amount to shift for aligning next_gid_index in mailbox: it
starts at bit 6, not bit 5.
. Allocate AMGM index after end of MGM table, in the range num_mgms to
multicast table size - 1. Add some BUG_ON checks to catch cases
where the index falls in the MGM hash area.
. Initialize the list of QPs in a newly-allocated group from AMGM to 0
This is necessary since when a group is moved from AMGM to MGM (in the
case where the MGM entry has been emptied of QPs), the AMGM entry is
not reset to 0 (and we don't want an extra command to do that).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
PKEY_INDEX is not a legal parameter in the RTR->RTS transition.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixes to SQEr->RTS transition in modify_qp:
1. The flag IB_QP_ACCESS_FLAGS is optional for UC qps
2. The SQEr state is not supported for RC qps
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a case where copying max_inline_data from a successful create_qp
capabilities output to create_qp input could cause EINVAL error:
mthca_set_qp_size must check max_inline_data directly against
max_desc_sz; checking qp->sq.max_gs is wrong since max_inline_data
depends on the qp type and does not involve max_sg.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix mthca_create_eq for when the EQ size is not a power of 2.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Modify_qp should check that the physical port number provided
is a legal value.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check error return on call to mthca_dev_lim for Tavor
(as is done for memfree).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Thinko: 64 bytes is the minimum SRQ WQE size (not the maximum).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
sae and sre bits should only be set when setting sra_max. Further, in
the old code, if the caller specifies max_rd_atomic = 0, the sre and
sae bits are still set, with the result that the QP ends up with
max_rd_atomic = 1 in effect.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch corrects some corner cases in managing the RAE/RRE bits in
the mthca qp context. These bits need to be zero if the user requests
max_dest_rd_atomic of zero. The bits need to be restored to the value
implied by the qp access flags attribute in a previous (or the
current) modify-qp command if the dest_rd_atomic variable is changed
to non-zero.
In the current implementation, the following scenario will not work:
RESET-to-INIT set QP access flags to all disabled (zeroes)
INIT-to-RTR set max_dest_rd_atomic=10, AND
set qp_access_flags = IB_ACCESS_REMOTE_READ | IB_ACCESS_REMOTE_ATOMIC
The current code will incorrectly take the access-flags value set in
the RESET-to-INIT transition.
We can simplify, and correct, this IB_QP_ACCESS_FLAGS handling: it is
always safe to set qp access flags in the firmware command if either
of IB_QP_MAX_DEST_RD_ATOMIC or IB_QP_ACCESS_FLAGS is set, so let's
just set it to the correct value, always.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When cleaning up a CQ for a QP attached to SRQ, need to free an SRQ
WQE only if the CQE is a receive completion.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
break only escapes from the innermost loop, and we want to escape both
loops and return an answer. Noticed by Ishai Rabinovitch.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only change the driver's copy of the QP attributes in modify QP after
checking the modify QP command completed successfully.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix thinko in rd_atomic calculation: ffs(x) - 1 does not find the next
power of 2 -- it should be fls(x - 1).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add limit checking on rd_atomic and dest_rd_atomic attributes:
especially for max_dest_rd_atomic, a value that is larger than HCA
capability can cause RDB overflow and corruption of another QP.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Free the memory allocated in mthca_init_user_db_tab() when releasing
the db_tab in mthca_cleanup_user_db_tab().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Unlike tavor, the max work queue size is an exact power of 2 for arbel
mode, despite what the documentation (of the QUERY_DEV_LIM firmware
command) says. Without this patch, on Arbel, we can start with a QP
of a valid size and get above the reported limit after rounding to the
next power of two.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On mem-free HCAs, when posting a long list of send requests, a
doorbell must be rung every 255 requests. Add code to handle this.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
last pointer is not updated when QP is modified to reset state. This
causes data corruption if WQEs are already posted on the queue.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Calculation of QP capabilities still isn't exactly right in mthca:
max_send_sge/max_recv_sge fields returned in create_qp can exceed the
handware supported limits.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Responder resources are only required to handle RDMA reads and atomic
operations, not RDMA writes. So the driver should allow RDMA writes
even if responder resources are set to 0. This is especially
important for the UC transport -- with the old code, it was impossible
to enable RDMA writes for UC QPs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In Tavor mode, when posting a long list of receive work requests, a
doorbell must be rung every 256 requests. Add code to do this when
required.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Handle case where prod_index has wrapped around and become less than
cq->cons_index by checking that their difference as a signed int is
positive rather than comparing directly.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The size of work requests for atomic operations was computed
incorrectly in mthca: all sizeofs need to be divided by 16.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the computation of QP capabilities (max scatter/gather entries,
max inline data, etc) into the kernel, and have the uverbs module
return the values as part of the create QP response. This keeps
precise knowledge of device limits in the low-level kernel driver.
This requires an ABI bump, so while we're making changes, get rid of
the max_sge parameter for the modify SRQ command -- it's not used and
shouldn't be there.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a typo in the rearming of the catastrophic error polling timer: we
should rearm the timer as long as the stop flag is _not_ set.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Report the device's real page size capability in mthca_query_device().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make sure that the P_Key index passed into mthca_modify_qp() is
within the device's P_Key table.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Mellanox has decided that the components of the firmware version are
really meant to be displayed in decimal, e.g. 0x000400070190 is
version 4.7.400. Change the format we use from "%x.%x.%x" to
"%d.%d.%d" to match this convention.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace kmalloc()+memset(,0,) with kzalloc(), for a net savings of 35
source lines and about 500 bytes of text.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix wqe_to_link() to use a structure field that we know is definitely
always unused for receive work requests, so that it really avoids the
free list corruption bug that the comment claims it does.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement reporting asynchronous CQ events in Mellanox HCA driver.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add some initial support for detecting and reporting catastrophic
errors reported by Mellanox HCAs. We start a periodic timer which
polls the catastrophic error reporting buffer in device memory. If an
error is detected, we dump the contents of the buffer for port-mortem
debugging, and report a fatal asynchronous error to higher levels.
In the future we can try to recover from these errors by resetting the
device, but this will require some work in higher-level code as well.
Let's get this in now, so that we at least get catastrophic errors
reported in logs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The UC transport does not support RDMA reads or atomic operations, so
we shouldn't require or even allow the consumer to set attributes
relating to these operations for UC QPs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The MAD layer was violating the DMA API by touching data buffers used
for sends after the DMA mapping was done. This causes problems on
non-cache-coherent architectures, because the device doing DMA won't
see updates to the payload buffers that exist only in the CPU cache.
Fix this by having all MAD consumers use ib_create_send_mad() to
allocate their send buffers, and moving the DMA mapping into the MAD
layer so it can be done just before calling send (and after any
modifications of the send buffer by the MAD layer).
Tested on a non-cache-coherent PowerPC 440SPe system.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We should always re-arm an event queue's interrupt in
mthca_tavor_interrupt() if the corresponding bit is set in the event cause
register (ECR), even if we didn't find any entries in the EQ. If we don't,
then there's a window where we miss an EQ entry and then get stuck because
we don't get another EQ event.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should always re-arm an event queue's interrupt in
mthca_tavor_interrupt() if the corresponding bit is set in the event
cause register (ECR), even if we didn't find any entries in the EQ.
If we don't, then there's a window where we miss an EQ entry and then
get stuck because we don't get another EQ event.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Avoid entering a QP as member of a multicast group multiple times.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make the type parameter of mthca_alloc_db() be an enum mthca_db_type
instead of an int. This doesn't have any practical effect but
documents the functions a little better.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Give each device a uverbs_cmd_mask, so that a low-level driver can
control which methods may be called on behalf of userspace.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check the sizes of CQs, QPs and SRQs when creating objects, and fail
instead of creating too-big queues. Also return real limits instead
of just plausible-sounding values from mthca_query_device().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hardware relies on us keeping one extra work request that never
gets used in SRQs. Add checks to the SRQ work request posting
functions so that they fail when someone is about to use up that extra
work request, rather than when someone uses the very last work request.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Our hardware supports generating an event when the number of receives
posted to a shared receive queue (SRQ) falls below a user-specified
limit. Implement mthca_modify_srq() to arm the limit, and add code to
handle dispatching SRQ events when they occur.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add code to fill in the bad_pkey_cntr, max_mtu, active_mtu and
subnet_timeout fields in mthca_query_port().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add abi_version attribute to uverbs class devices to allow for
ABI versioning of device-specific interfaces.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Return correct atomic capability flag from mthca query function.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remember to free the multicast group context memory table.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB spec defines the field to be 32 bits, not 16 bits.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When allocating a table for mem-free HCA context, don't assume that
obj_size * nobj is an even multiple of MTHCA_TABLE_CHUNK_SIZE. In
particular, make sure we allocate at least one slot even if the table
is smaller than MTHCA_TABLE_CHUNK_SIZE.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The loop in mthca_map_cmd() would fill one entry past the end of the
mailbox buffer before calling the firmware command.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We should use the first word of the clear interrupt register if
the bit we're after is < 32, not < 31.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If we allocate a bunch of doorbell records and then free them, we'll
end up with completely empty pages, which we then free. However, when
we come back to allocate more doorbell pages, we have to reallocate
those empty pages rather than always trying to take a slot that we've
never used. If we don't, we eventually use up every slot and fail to
allocate a doorbell record, even though we have plenty of free space.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Userspace SRQs don't have a buffer allocated for them in the kernel, so
it doesn't make sense to set srq->last during initialization. In fact,
this can crash trying to follow a nonexistent buffer pointer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error handling paths in mthca_tavor_post_srq_recv() and
mthca_arbel_post_srq_recv() are quite bogus, the result of a
screwed up merge. Fix them so they work as intended.
Pointed out by Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mthca_create_eq(), we call get_eqe() before setting eq->nent. This
is wrong, because get_eqe() uses eq->nent. Fix this, and clean up the
code a little while we're at it. (We got lucky with the current code,
because eq->nent was cleared to 0, which get_eqe() made happen to do
the right thing)
Pointed out by Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix posting first WQE for mem-free HCAs: we need to link to previous
WQE even in that case. While we're at it, simplify code for
Tavor-mode HCAs. We don't really need the conditional test there
either; we can similarly always link to the previous WQE.
Based on Michael S. Tsirkin's analogous fix for userspace libmthca.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hardware reads the ACK timeout field from the most significant 5
bits of struct mthca_qp_path's ackto field, not the least significant
bits. This fix has the driver put the timeout in the right place.
Without this, we get a timeout that is 2^8 times too small.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When we modify a QP to the RESET state, completely clean up the QP
so that it is really and truly reset.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the InfiniBand headers from drivers/infiniband/include to include/rdma.
This allows InfiniBand-using code to live elsewhere, and lets us remove the
ugly EXTRA_CFLAGS include path from the InfiniBand Makefiles.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When creating a table in context memory where the table is smaller
than our chunk size, we don't want to allocate and map a full chunk.
Instead, allocate just enough memory to cover the table.
This can be pretty simple because all tables are a power-of-2 size, so
either the table is a multiple of the chunk size, or it's smaller than
one chunk.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the definitions of the WQE structures from mthca_qp.c into
mthca_wqe.h, so that we'll be able to share them when we add the
SRQ code in mthca_srq.c.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Mem-free HCAs never generate error CQEs that complete multiple WQEs,
so just skip the call to mthca_free_err_wqe() for them rather than
having logic to handle the mem-free case in mthca_free_err_wqe().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up the allocation of memory for queues by factoring out the
common code into mthca_buf_alloc() and mthca_buf_free(). Now CQs and
QPs share the same queue allocation code, which we'll also use for SRQs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the max_msg_sz port property correctly in mthca's port_query
function. Also zero out the attr struct so that we don't leave
any other members uninitialized.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When we call the INIT_IB firmware command to bring up a port, use
the actual port width capability returned by the QUERY_DEV_LIM
command instead of always trying to enable both 1X and 4X. This
fixes breakage seen when the firmware is build to allow 4X only.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
changing CONFIG_LOCALVERSION rebuilds too much, for no appearent reason.
Remove unneeded includes of <linux/version.h>.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the generic key_to_hw_index() function instead of the Arbel-specific
version in mthca_free_region().
Signed-off-by: Guy German <guyg@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for reporting HCA board ID returned from QUERY_ADAPTER
firmware command through sysfs.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make some lawyers happy and add copyright notices for people who
forgot to include them when they actually touched the code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Update FW versions in mthca according to July 05 Mellanox release
Signed-off-by: Tziporet Koren <tziporet@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use io_remap_pfn_range to remap IO pages (remap_pfn_range is for memory).
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix handling of error CQ entries on mem-free HCAs: the doorbell count
is never valid so we shouldn't look at it. This fixes problems exposed
by new HCA firmware.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for userspace queue pairs (QPs) to mthca.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for userspace completion queues (CQs) to mthca.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for userspace memory regions (MRs) to mthca.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for userspace protection domains (PDs) to mthca.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for mmap() method to mthca, so that userspace can get access to
doorbell registers. This allows userspace to get direct access to the HCA for
data path operations.
Each userspace context gets its own copy of the doorbell registers and is only
allowed to use resources that the kernel has given it access to. In other
words, this is safe.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for managing userspace contexts to mthca.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for userspace doorbell records to mthca.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the mthca_user.h header file, which defines the device-specific ABI used
by the mthca low-level driver for kernel/user communication.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update mthca to compile against the updated API for low-level drivers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's about time for a version bump.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Future versions of Mellanox HCA firmware will require command mailboxes to be
aligned to 4K. Support this by using a pci_pool to allocate all mailboxes.
This has the added benefit of shrinking the source and text of mthca.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Free page_list buffer on error path of mthca_reg_phys_mr().
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Split allocation of MTT range from creation of MR. This will be useful for
implementing shared memory regions and userspace verbs.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make mthca_table_put() and mthca_table_put_range() NOPs if the device is not
mem-free, so that we don't have to have "if (mthca_is_memfree())" tests in the
callers of these functions. This makes our code more readable and
maintainable, and saves a couple dozen bytes of text in ib_mthca.ko as well.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix memset to use sizeof *props instead of just sizeof props.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for unreliable connected (UC) transport to mthca driver:
- Add attributes for UC to modify QP table.
- Add support for posting UC work requests.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mthca apparently had the meanings of the max_rd_atomic and max_dest_rd_atomic
QP attributes backwards. max_rd_atomic limits the maximum number of
outstanding RDMA/atomic requests as an initiator (on a send queue), and
max_dest_rd_atomic specifies the resources allocated to handle RMDA/atomic
requests from the remote end of the connection. We were programming our QP
context with these values swapped.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix offset of static_rate in QP context. Pointed out by Dror Goldenberg.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roland Dreier