PS3 EHCI HC errata fix 244. The SCC EHCI HC will not correctly perform QH
reads that occur near or span a micro-frame boundry. This is due to a problem
in the Nak Count Reload Control logic (EHCI Specification 1.0 Section 4.9.1).
The work-around for this problem is for the HC driver to set I=1 (inactive) for
QHs with H=1 (list head).
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The EHCI USB controller of the Cell Super Companion Chip used in the PS3
will stop the root hub after all root hub ports are suspended. When in
this condition the ehci-hcd handshake routine will return -ETIMEDOUT and
the USB runtime suspend sequence will fail. The STS_HLT bit will not be
set, so inspection of the frame index is used to test for the condition.
Add a new routine handshake_for_broken_root_hub() that is called after
an unsuccessful -ETIMEDOUT handshake. On PS3 handshake_for_broken_root_hub()
will test for the condition, and if found will return success to allow the
USB suspend to complete. For all other platforms
handshake_for_broken_root_hub() will return -ETIMEDOUT
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Remove the ehci_reset() call done in the ehci_run() routine of the
USB EHCI host controller driver and add an ehci_reset() call to the
probe processing of all EHCI platform drivers that do not already call
ehci_reset().
The call to ehci_reset() from ehci_run() was problematic for several
platform drivers, and unnecessary for others. This change moves the
decision to call ehci_reset() at driver startup to the platform
driver code.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Use CONFIG_CPU_XLR instead of CONFIG_NLM_XLR, the NLM_XLR config
option is redundant and is being removed.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch (as1489) works around a hardware bug in MosChip EHCI
controllers. Evidently when one of these controllers increments the
frame-index register, it changes the three low-order bits (the
microframe counter) before changing the higher order bits (the frame
counter). If the register is read at just the wrong time, the value
obtained is too low by 8.
When the appropriate quirk flag is set, we work around this problem by
reading the frame-index register a second time if the first value's
three low-order bits are all 0. This gives the hardware a chance to
finish updating the register, yielding the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jason N Pitt <jpitt@fhcrc.org>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI_SHRINK_JIFFIES should be 5ms, which was just used originally,
and not 200ms, so fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1483) improves the ehci-hcd driver family by getting rid
of the reliance on the hcd->state variable. It has no clear owner and
it isn't protected by the usual HCD locks. In its place, the patch
adds a new, private ehci->rh_state field to record the state of the
root hub.
Along the way, the patch removes a couple of lines containing
redundant assignments to the state variable. Also, the QUIESCING
state simply gets changed to the RUNNING state, because the driver
doesn't make any distinction between them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add supprt for on-chip USB controller for Netlogic XLS MIPS64
SoC processor family.
Changes are:
- update ehci-hcd.c and ohci-hcd.c to add XLS hcds
- add ehci-xls.c: EHCI support for Netlogic XLS.
- add ohci-xls.c: OHCI support for Netlogic XLS.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (115 commits)
EHCI: fix direction handling for interrupt data toggles
USB: serial: add IDs for WinChipHead USB->RS232 adapter
USB: OHCI: fix another regression for NVIDIA controllers
usb: gadget: m66592-udc: add pullup function
usb: gadget: m66592-udc: add function for external controller
usb: gadget: r8a66597-udc: add pullup function
usb: renesas_usbhs: support multi driver
usb: renesas_usbhs: inaccessible pipe is not an error
usb: renesas_usbhs: care buff alignment when dma handler
USB: PL2303: correctly handle baudrates above 115200
usb: r8a66597-hcd: fixup USB_PORT_STAT_C_SUSPEND shift
usb: renesas_usbhs: compile/config are rescued
usb: renesas_usbhs: fixup comment-out
usb: update email address in ohci-sh and r8a66597-hcd
usb: r8a66597-hcd: add function for external controller
EHCI: only power off port if over-current is active
USB: mon: Allow to use usbmon without debugfs
USB: EHCI: go back to using the system clock for QH unlinks
ehci: add pci quirk for Ordissimo and RM Slate 100 too
ehci: refactor pci quirk to use standard dmi_check_system method
...
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
This patch (as1477) fixes a problem affecting a few types of EHCI
controller. Contrary to what one might expect, these controllers
automatically stop their internal frame counter when no ports are
enabled. Since ehci-hcd currently relies on the frame counter for
determining when it should unlink QHs from the async schedule, those
controllers run into trouble: The frame counter stops and the QHs
never get unlinked.
Some systems have also experienced other problems traced back to
commit b963801164 (USB: ehci-hcd unlink
speedups), which made the original switch from using the system clock
to using the frame counter. It never became clear what the reason was
for these problems, but evidently it is related to use of the frame
counter.
To fix all these problems, this patch more or less reverts that commit
and goes back to using the system clock. But this can't be done
cleanly because other changes have since been made to the scan_async()
subroutine. One of these changes involved the tricky logic that tries
to avoid rescanning QHs that have already been seen when the scanning
loop is restarted, which happens whenever an URB is given back.
Switching back to clock-based unlinks would make this logic even more
complicated.
Therefore the new code doesn't rescan the entire async list whenever a
giveback occurs. Instead it rescans only the current QH and continues
on from there. This requires the use of a separate pointer to keep
track of the next QH to scan, since the current QH may be unlinked
while the scanning is in progress. That new pointer must be global,
so that it can be adjusted forward whenever the _next_ QH gets
unlinked. (uhci-hcd uses this same trick.)
Simplification of the scanning loop removes a level of indentation,
which accounts for the size of the patch. The amount of code changed
is relatively small, and it isn't exactly a reversion of the
b963801164 commit.
This fixes Bugzilla #32432.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Tested-by: Matej Kenda <matejken@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are cases, when 80% max isochronous bandwidth is too limiting.
For example I have two USB video capture cards which stream uncompressed
video, and to stream full NTSC + PAL videos we'd need
NTSC 640x480 YUV422 @30fps ~17.6 MB/s
PAL 720x576 YUV422 @25fps ~19.7 MB/s
isoc bandwidth.
Now, due to limited alt settings in capture devices NTSC one ends up
streaming with max_pkt_size=2688 and PAL with max_pkt_size=2892, both
with interval=1. In terms of microframe time allocation this gives
NTSC ~53us
PAL ~57us
and together
~110us > 100us == 80% of 125us uframe time.
So those two devices can't work together simultaneously because the'd
over allocate isochronous bandwidth.
80% seemed a bit arbitrary to me, and I've tried to raise it to 90% and
both devices started to work together, so I though sometimes it would be
a good idea for users to override hardcoded default of max 80% isoc
bandwidth.
After all, isn't it a user who should decide how to load the bus? If I
can live with 10% or even 5% bulk bandwidth that should be ok. I'm a USB
newcomer, but that 80% set in stone by USB 2.0 specification seems to be
chosen pretty arbitrary to me, just to serve as a reasonable default.
NOTE 1
~~~~~~
for two streams with max_pkt_size=3072 (worst case) both time
allocation would be 60us+60us=120us which is 96% periodic bandwidth
leaving 4% for bulk and control. Alan Stern suggested that bulk then
would be problematic (less than 300*8 bittimes left per microframe), but
I think that is still enough for control traffic.
NOTE 2
~~~~~~
Sarah Sharp expressed concern that maxing out periodic bandwidth
could lead to vendor-specific hardware bugs on host controllers, because
> It's entirely possible that you'll run into
> vendor-specific bugs if you try to pack the schedule with isochronous
> transfers. I don't think any hardware designer would seriously test or
> validate their hardware with a schedule that is basically a violation of
> the USB bus spec (more than 80% for periodic transfers).
So far I've only tested this patch on my HP Mini 5103 with N10 chipset
kirr@mini:~$ lspci
00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge
00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller
00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 02)
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02)
01:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8059 PCI-E Gigabit Ethernet Controller (rev 11)
and the system works stable with 110us/uframe (~88%) isoc bandwith allocated for
above-mentioned isochronous transfers.
NOTE 3
~~~~~~
This feature is off by default. I mean max periodic bandwidth is set to
100us/uframe by default exactly as it was before the patch. So only those of us
who need the extreme settings are taking the risk - normal users who do not
alter uframe_periodic_max sysfs attribute should not see any change at all.
NOTE 4
~~~~~~
I've tried to update documentation in Documentation/ABI/ thoroughly, but
only "TBD" was put into Documentation/usb/ehci.txt -- the text there seems
to be outdated and much needing refreshing, before it could be amended.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only sysfs attr implemented so far is "companion" from ehci-hub.c,
but in the next patch we are going to add another sysfs file, so prior
to that let's structure things and move already-in-there sysfs code to
separate file.
NOTE: All the code I'm moving into this new file was written by Alan
Stern (in 57e06c11 "EHCI: force high-speed devices to run at full
speed"; Jan 16 2007), that's why I'm putting
Copyright (C) 2007 by Alan Stern
there after explicit request from the author.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Following the loss of David Brownell, I volunteer to maintain the
ohci-hcd and ehci-hcd drivers. This patch (as1472) makes it official.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need to have a "\n" on a MODULE_PARM_DESC, remove it
Signed-off-by: Niels de Vos <ndevos@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1467) removes the last usages of hcd->state from
usbcore. We no longer check to see if an interrupt handler finds that
a controller has died; instead we rely on host controller drivers to
make an explicit call to usb_hc_died().
This fixes a regression introduced by commit
9b37596a2e (USB: move usbcore away from
hcd->state). It used to be that when a controller shared an IRQ with
another device and an interrupt arrived while hcd->state was set to
HC_STATE_HALT, the interrupt handler would be skipped. The commit
removed that test; as a result the current code doesn't skip calling
the handler and ends up believing the controller has died, even though
it's only temporarily stopped. The solution is to ignore HC_STATE_HALT
following the handler's return.
As a consequence of this change, several of the host controller
drivers need to be modified. They can no longer implicitly rely on
usbcore realizing that a controller has died because of hcd->state.
The patch adds calls to usb_hc_died() in the appropriate places.
The patch also changes a few of the interrupt handlers. They don't
expect to be called when hcd->state is equal to HC_STATE_HALT, even if
the controller is still alive. Early returns were added to avoid any
confusion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Manuel Lauss <manuel.lauss@googlemail.com>
CC: Rodolfo Giometti <giometti@linux.it>
CC: Olav Kongas <ok@artecdesign.ee>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the GRLIB GRUSBHC EHCI controller from
Aeroflex Gaisler. The controller is typically found on LEON/GRLIB
SoCs.
Tested on GR-LEON4-ITX with with little endian interface and on
LEON3 system on GR-PCI-XC5V development board for big endian
controller.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.
This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Atheros AR71XX/AR91XX SoCs have a built-in EHCI controller.
This patch adds the necessary glue code to make the generic EHCI
driver usable for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds host USB high speed driver for samsung S5P series. This
is initial driver and we need additional implementation to support some
functions like power management.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.
The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SH EHCI/OHCI driver hardcoded the CPU type in {ehci,ohci}-hcd.c.
So if we will add the new CPU, we had to add to the hcd driver each time.
The patch adds the CONFIG_USB_{EHCI,OHCI}_SH configuration. So if we
want to use the SH EHCI/OHCI, we only enable the configuration.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.
AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:
1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.
Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:
1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
make them cleaner;
2. AMD chipset information will be probed only once and then stored.
Currently they're probed during every OHCI/EHCI initialization, move
the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
code, every host controller enable/disable PLL only according to
its own status, and may enable PLL while there is still isoc transfer on
other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of users of of_platform_driver in drivers/usb. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch add bus glue for USB controller commonly found in PMC-Sierra MSP71xx family of SoC's.
Signed-off-by: Anoop P A <anoop.pa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
TDI driver does the ehci_reset in their reset callback.
Don't reset in ehci_run because configuration settings done in
platform driver will be reset.
This will allow to make msm use ehci_run.
Signed-off-by: Matthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1440) fixes a bug in ehci-hcd. ehci->periodic_size is
used to compute the size in a dma_alloc_coherent() call, but then it
gets changed later on. As a result, the corresponding call to
dma_free_coherent() passes a different size from the original
allocation. Fix the problem by adjusting ehci->periodic_size before
carrying out any of the memory allocations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
CC: David Brownell <david-b@pacbell.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
This patch adds support for EHCI compliant HSUSB Host controller found
on MSM chips. The root hub has a single port and TT is built into it.
This driver depends on OTG driver for PHY initialization, clock
management and powering up VBUS.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When ASPM PM Feature is enabled on UMI link, devices that use ISOC stream of
data transfer may be exposed to longer latency causing less than optimal per-
formance of the device. The longer latencies are normal and are due to link
wake time coming out of low power state which happens frequently to save
power when the link is not active.
The following code will make exception for certain features of ASPM to be by
passed and keep the logic normal state only when the ISOC device is connected
and active. This change will allow the device to run at optimal performance
yet minimize the impact on overall power savings.
Signed-off-by: Alex He <alex.he@amd.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'sh/ehci' of master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Convert to USB_ARCH_HAS_OHCI/EHCI selects.
usb: ehci-sh: Add missing ehci helpers.
usb: ehci-sh: Fix up fault in shutdown path.
sh: Add EHCI support for SH7786.
usb: ehci-hcd: Add support for SuperH EHCI.
usb: ohci-sh: Set IRQ as shared.
Introduce the CONFIG_USB_EHCI_HCD_OMAP option to select
EHCI support on OMAP3 and later chips. This scales better
than having a long line of dependencies for each new OMAP
with EHCI support.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
The CNS3XXX SOC has include USB EHCI and OHCI compatible controllers.
This patch adds the necessary glue logic to allow ehci-hcd and ohci-hcd
drivers to work on CNS3XXX
The EHCI and OHCI controllers share a common clock control and reset
bit, therefore additional check for the timming of enabling and disabling
is required. The USB bit of PLL Power Down Control is also shared by OTG,
24MHzUART clock, Crypto clock, PCIe reference clock, and Clock Scale
Generator. Therefore we only ensure it is enabled, while not disabling it.
Signed-off-by: Mac Lin <mkl0301@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch adds support for ehci and ohci controller in the SPEAr platform.
Changes since V2:
added clear_tt_buffer_complete in ehci_spear_hc_driver
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1435) fixes an obscure and unlikely race in ehci-hcd.
When an async URB is unlinked, the corresponding QH is removed from
the async list. If the QH's endpoint is then disabled while the URB
is being given back, ehci_endpoint_disable() won't find the QH on the
async list, causing it to believe that the QH has been lost. This
will lead to a memory leak at best and quite possibly to an oops.
The solution is to trust usbcore not to lose track of endpoints. If
the QH isn't on the async list then it doesn't need to be taken off
the list, but the driver should still wait for the QH to become IDLE
before disabling it.
In theory this fixes Bugzilla #20182. In fact the race is so rare
that it's not possible to tell whether the bug is still present.
However, adding delays and making other changes to force the race
seems to show that the patch works.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
CC: David Brownell <david-b@pacbell.net>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
VIA and WonderMedia Systems-on-Chip feature a standard EHCI host
controller. This adds necessary glue to use the standard driver
with these systems.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OCTEON II SOC has USB EHCI and OHCI controllers connected directly
to the internal I/O bus. This patch adds the necessary 'glue' logic
to allow ehci-hcd and ohci-hcd drivers to work on OCTEON II.
The OCTEON normally runs big-endian, and the ehci/ohci internal
registers have host endianness, so we need to select
USB_EHCI_BIG_ENDIAN_MMIO.
The ehci and ohci blocks share a common clocking and PHY
infrastructure. Initialization of the host controller and PHY clocks
is common between the two and is factored out into the
octeon2-common.c file.
Setting of USB_ARCH_HAS_OHCI and USB_ARCH_HAS_EHCI is done in
arch/mips/Kconfig in a following patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1675/
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
tdi_reset is already taking care of setting host mode for tdi devices.
Don't duplicate code in platform driver.
Make ehci_halt a nop if the controller is not in host mode (otherwise it
will fail), and let's ehci_reset do the tdi_reset.
We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt
knows we are a tdi device.
Before the setup routine was doing :
- put controller in host mode
- ehci_halt
- ehci_init
- hcd->has_tt = 1;
- ehci_reset
Now we do :
- hcd->has_tt = 1;
- ehci_halt
- ehci_init
- ehci_reset
PS : now we handle correctly the device -> host transition.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1407) fixes a bug in ehci-hcd's isochronous scheduler.
All its calculations should be done in terms of microframes, but for
full-speed devices, sched->span is stored in frames. It needs to be
converted.
This fix is liable to expose problems in other drivers. The old code
would accept URBs that should not have been accepted, so drivers have
had no reason to avoid submitting URBs that exceeded the maximum
schedule length. In an attempt to partially compensate for this, the
patch also adjusts the schedule length from a minimum of 256 frames up
to a minimum of 512 frames.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we use the HCD_LOCAL_MEM flag and dma_declare_coherent_memory() to
enforce the host controller's local memory utilization we also need to
disable native scatter-gather support, otherwise hcd_alloc_coherent() in
map_urb_for_dma() is called with urb->transfer_buffer == NULL, that
triggers a NULL pointer dereference.
We can also consider to add a WARN_ON() and return an error code to
better catch this problem in the future.
At the moment no driver seems to hit this bug, so I should
consider this a low-priority fix.
Signed-off-by: Andrea Righi <arighi@develer.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1393) converts several of the single-bit fields in
struct usb_hcd to atomic flags. This is for safety's sake; not all
CPUs can update bitfield values atomically, and these flags are used
in multiple contexts.
The flag fields that are set only during registration or removal can
remain as they are, since non-atomic accesses at those times will not
cause any problems.
(Strictly speaking, the authorized_default flag should become atomic
as well. I didn't bother with it because it gets changed only via
sysfs. It can be done later, if anyone wants.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch will enable Per-port event feature defined in EHCI 1.1
addendum. This feature addresses an issue where HCD is currently
required to read and parse PORTSC for all enabled root hub ports. With
this patch, the overhead will be reduced.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With this patch, the LPM capable EHCI host controller can put device
into L1 sleep state which is a mode that can enter/exit quickly, and
reduce power consumption.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI 1.1 addendum introduced several energy efficiency extensions for
EHCI USB host controllers:
1. LPM (link power management)
2. Per-port change
3. Shorter periodic frame list
4. Hardware prefetching
This patch is intended to define the HW bits and debug interface for
EHCI 1.1 addendum. The LPM and Per-port change patches will be sent out
after this patch.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg prefers this to go through the trivial tree.
http://lkml.org/lkml/2010/6/24/1
There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.
Standardize them a bit.
Moved a statement down a line in drivers/usb/host/u132-hcd.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes the driver to allow both CONFIG_USB_EHCI_HCD_PPC_OF and
CONFIG_USB_ECHI_HCD_XILINX to be selected.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: John Linn <john.linn@xilinx.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1369) fixes a problem in ehci-hcd. Some controllers
occasionally run into trouble when the driver reclaims siTDs too
quickly. This can happen while streaming audio; it causes the
controller to crash.
The patch changes siTD reclamation to work the same way as iTD
reclamation: Completed siTDs are stored on a list and not reused until
at least one frame has passed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Nate Case <ncase@xes-inc.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The EHCI driver stores in usb_host_endpoint.hcpriv a pointer to either
an ehci_qh or an ehci_iso_stream structure, and uses the contents of the
hw_info1 field to distinguish the two cases.
After ehci_qh was split into hw and sw parts, ehci_iso_stream must also
be adjusted so that it again looks like an ehci_qh structure.
This fixes a NULL pointer access in ehci_endpoint_disable() when it
tries to access qh->hw->hw_info1.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1330) fixes a bug in khbud's handling of remote
wakeups. When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes. At
this point the port's SUSPEND feature is automatically turned off.
However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec). Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup. This patch adds the missing
delay to the remote-wakeup path.
It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes). The extra time appears to help some
devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1300) adds native scatter-gather support to ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Freescale MX27 and MX31 SoCs have a EHCI controller onboard.
The controller is capable of USB on the go. This patch adds
a driver to support all three of them.
Users have to pass details about serial interface configuration in the
platform data.
The USB OTG core used here is the ARC core, so the driver should
be renamed and probably be merged with ehci-fsl.c eventually.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The EHCI specification says that an EHCI host controller may cache part of
the isochronous schedule. The EHCI controller must advertise how much it
caches in the schedule through the HCCPARAMS register isochronous
scheduling threshold (IST) bits.
In theory, adding new iTDs within the IST should be harmless. The HW will
follow the old cached linked list and miss the new iTD. SW will notice HW
missed the iTD and return 0 for the transfer length.
However, Intel ICH9 chipsets (and some later chipsets) have issues when SW
attempts to schedule a split transaction within the IST. All transfers
will cease being sent out that port, and the drivers will see isochronous
packets complete with a length of zero. Start of frames may or may not
also disappear, causing the device to go into auto-suspend. This "bus
stall" will continue until a control or bulk transfer is queued to a
device under that roothub.
Most drivers will never cause this behavior, because they use multiple
URBs with multiple packets to keep the bus busy. If you limit the number
of URBs to one, you may be able to hit this bug.
Make sure the EHCI driver does not schedule full-speed transfers within
the IST under an Intel chipset. Make sure that when we fall behind the
current microframe plus IST, we schedule the new transfer at the next
periodic interval after the IST.
Don't change the scheduling for new transfers, since the schedule slop will
always be greater than the IST. Allow high speed isochronous transfers to
be scheduled within the IST, since this doesn't trigger the Intel chipset
bug.
Make sure that if the host caches the full frame, the EHCI driver's
internal isochronous threshold (ehci->i_thresh) is set to
8 microframes + 2 microframes wiggle room. This is similar to what is done in
the case where the host caches less than the full frame.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this driver has been sitting in linux-omap tree for quite
some time. It adds support for omap's ehci controller.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add bus glue driver for Xilinx USB host controller. The controller can be
configured as HS only or HS/FS hybrid. The driver uses the device tree file
to configure the driver according to the setting in the hardware system.
This driver has been tested with usbtest using the NET2280 PCI card.
Signed-off-by: Julie Zhu <julie.zhu@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the EHCI debug port is initialized and in use, the EHCI host
controller driver must follow two rules.
1) If the EHCI host driver issues a controller reset, the debug
controller driver re-initialization must get called after the reset
is completed.
2) The EHCI host driver should ignore any requests to the physical
EHCI debug port when the EHCI debug port is in use.
The code to check for the debug port was moved from ehci_pci_reinit()
to ehci_pci_setup because it must get called prior to ehci_reset()
which will clear the debug port registers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: dbrownell@users.sourceforge.net
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1281) changes the way ehci-hcd deschedules interrupt
QHs, copying the approach used for async QHs. The caller is no longer
responsible for rescheduling the QH if its queue is non-empty; instead
the reschedule is done directly by intr_deschedule(), after calling
qh_completions(). This is exactly the same as how end_unlink_async()
works.
ehci_urb_dequeue() and intr_deschedule() now correctly handle the case
where they are called while another interrupt URB for the same QH is
being given back. This was a surprisingly large blind spot. And
scan_periodic() now respects the new needs_rescan flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1280) fixes an obscure bug in ehci-hcd's dequeuing logic
for async URBs. If a later URB is unlinked and the completion
routine unlinks an earlier URB, then the earlier URB won't be given
back in a timely manner because the endpoint queue isn't rescanned as
it should be.
Similar bugs occur if an endpoint is reset or a halt is cleared while
a completion routine is running, because the subroutines don't test
for the COMPLETING state.
All these problems are solved by adding a new needs_rescan flag to the
ehci_qh structure. If the flag is set while scanning through an idle
QH, the scan will be repeated. If the QH isn't idle then an unlink
cycle will be initiated, and the proper action will be taken when it
becomes idle.
Also, an unnecessary test is removed from qh_link_async(): That
routine is never called if the QH's state isn't IDLE.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add host USB High speed driver for at91sam9g45 series.
The host driver is an EHCI with its companion OHCI. EHCI is
handled by the new ehci-atmel.c whereas the OHCI is always
handled by ohci-at91.c.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
The Intel Moorestown EHCI controller supports non-standard HOSTPCx register
extension. This register controls the LPM behaviour and controls the behaviour
of each USB port.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ehci_qh structure merged hw and sw together which is not good:
1. More and more items are being added into ehci_qh, the ehci_qh software
part are unnecessary to be allocated in DMA qh_pool.
2. If HCD has local SRAM, the sw part will consume it too, and it won't
bring any benefit.
3. For non-cache-coherence system, the entire ehci_qh is uncachable, actually
we only need the hw part to be uncacheable. Spliting them will let the sw
part to be cacheable.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Basically the io watchdog is only useful for those quirk HCDs. For most
good ones, it only brings unnecessary wakeups. At least, I know the
Intel EHCI HCDs should turn off the flag.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ehci support for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1273) fixes two(!) bugs introduced by the new
Clear-TT-Buffer implementation in ehci-hcd.
It is now possible for an idle QH to have some URBs on its
queue -- this will happen if a Clear-TT-Buffer is pending for
the QH's endpoint. Consequently we should not issue a warning
when someone tries to unlink an URB from an idle QH; instead
we should process the request immediately.
The refcounts for QHs could get messed up, because
submit_async() would increment the refcount when calling
qh_link_async() and qh_link_async() would then refuse to link
the QH into the schedule if a Clear-TT-Buffer was pending.
Instead we should increment the refcount only when the QH
actually is added to the schedule. The current code tries to
be clever by leaving the refcount alone if an unlink is
immediately followed by a relink; the patch changes this to an
unconditional decrement and increment (although they occur in
the opposite order).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Tested-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1256) changes ehci-hcd and all the other drivers in the
EHCI family to make use of the new clear_tt_buffer callbacks. When a
Clear-TT-Buffer request is in progress for a QH, the QH is not allowed
to be linked into the async schedule until the request is finished.
At that time, if there are any URBs queued for the QH, it is linked
into the async schedule.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is an update to the "usb-ehci-update-toggle-state-for-linked-qhs"
patch. Since an HCD's endpoint_reset method can be called in
interrupt context, it mustn't assume that interrupts are enabled or
that it can sleep.
So we revert to the original way of refreshing QHs' toggle bits. Now
the endpoint_reset method merely clears the toggle flag in the device
structure (as was done before) and starts an async QH unlink. When the
QH is linked again, after the unlink finishes and an URB is queued,
the qh_refresh() routine will update the QH's toggle bit.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: David <david@unsolicited.net>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1245) fixes a bug in ehci-hcd. When an URB is queued
for an endpoint whose QH is already in the LINKED state, the QH
doesn't get refreshed. As a result, if usb_clear_halt() was called
during the time that the QH was linked but idle, the data toggle value
in the QH doesn't get reset.
The symptom is that after a clear_halt, data gets lost and transfers
time out. This problem is starting to show up now because the
"ehci-hcd unlink speedups" patch causes QHs with no queued URBs to
remain linked for a suitable time.
The patch utilizes the new endpoint_reset mechanism to fix the
problem. When an endpoint is reset, the new method forcibly unlinks
the QH (if necessary) and safely updates the toggle value. This
allows qh_update() to be simplified and avoids using usb_device's
toggle bits in a rather unintuitive way.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: David <david@unsolicited.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1205) moves timer_action() from ehci.h to ehci-hcd.c and
makes it out-of-line. Over the years it has grown too big to be inline
any more.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently ITDs are immediately recycled whenever their URB completes.
However, EHCI hardware can sometimes remember some ITD state. This
means that when the ITD is reused before end-of-frame it may sometimes
cause the hardware to reference bogus state.
This patch defers reusing such ITDs by moving them into a new ehci member
cached_itd_list. ITDs resting in cached_itd_list are moved back into their
stream's free_list once scan_periodic() detects that the active frame has
elapsed.
This makes the snd_usb_us122l driver (in kernel since .28) work right
when it's hooked up through EHCI.
[ dbrownell@users.sourceforge.net: comment fixups ]
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Tested-by: Philippe Carriere <philippe-f.carriere@wanadoo.fr>
Tested-by: Federico Briata <federicobriata@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1165) makes a few small changes in the logic used by
ehci-hcd when it encounters a controller error:
Instead of printing out the masked status, it prints the
original status as read directly from the hardware.
It doesn't check for the STS_HALT status bit before taking
action. The mere fact that the STS_FATAL bit is set means
that something bad has happened and the controller needs to
be reset. With the old code this test could never succeed
because the STS_HALT bit was masked out from the status.
I anticipate that this will prevent the occasional "irq X: nobody cared"
problem people encounter when their EHCI controllers die.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This gets rid of an annoying warning in ehci-hcd.c when DEBUG isn't
enabled:
warning: label 'err_debug' defined but not used
by moving it inside the already-existing #ifdef DEBUG, so that it
matches the goto. And now my regular build is warning-free again.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1147) fixes the remote-wakeup support for EHCI
controllers using the ARC/TDI "embedded-TT" core. These controllers
turn off the RESUME bit by themselves when a port resume is complete;
hence we need to keep separate track of which ports are suspended or
in the process of resuming.
The patch also makes a couple of small improvements in ehci_irq(),
replacing reads of the command register with the value already stored
in a local variable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Thomas Reitmayr <treitmayr@devbase.at>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1139) adds a warning to the system log whenever ehci-hcd
is loaded after ohci-hcd or uhci-hcd. Nowadays most distributions are
pretty good about not doing this; maybe the warning will help convince
anyone still doing it wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.27]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1145) removes the essentially useless driver-version
strings from ehci-hcd, ohci-hcd, and uhci-hcd. It also unifies the
form of the banner lines they display upon loading and adds a missing
test for usb_disabled() to ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore remove
the dead code associated with !CONFIG_PPC_MERGE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is based on the following ideas:
1. Some usb devices (such as usb video class) have endpoints of high
interval attribute, so reading "periodic" file need more debug buffer
to accommodate the qh or itd schedule information. For example, 4KB
buffer is not enough for a single interrupt qh of 2ms period.
2. print a %p need 16 byte buffer on 64-bits arch, but 8 byte on 32-bits
arch. Add a extra bonus for 64-bits arch.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that the "Refactor "if (handshake()) state = HC_STATE_HALT"
patch from earlier this year perpetuated a potential problem: it can
mark the controller as halted when it's still running (but not acting
as, perhaps wrongly, expected).
That caused some hangs and crashes, rather than more polite failure
modes of a truly halted controller. This patch forces a true halt,
and emits a (previously missing) diagnostic.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes some performance bugs observed with some workloads
when unlinking EHCI queue header (QH) descriptors from the async ring
(control/bulk schedule).
The mechanism intended to defer unlinking an empty QH (so there is no
penalty in common cases where it's quickly reused) was not working as
intended. Sometimes the unlink was scheduled:
- too quickly ... which can be a *strong* negative effect, since
that QH becomes unavailable for immediate re-use;
- too slowly ... wasting DMA cycles, usually a minor issue except
for increased bus contention and power usage;
Plus there was an extreme case of "too slowly": a logical error in the
IAA watchdog-timer conversion meant that sometimes the unlink never
got scheduled.
The fix replaces a simple counter with a timestamp derived from the
controller's 8 KHz microframe counter, and adjusts the timer usage
for some issues associated with HZ being less than 8K.
(Based on a patch originally by Alan Stern, and good troubleshooting
from Leonid.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Leonid <leonidv11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch refactors some shutdown code so it can be shared between
ehci_stop() and ehci_shutdown().
This also fixes a couple potential bugs:
- ehci_shutdown() was not locking ehci->lock before halting the HC.
- ehci_shutdown() didn't disable the watchdog and IAA timers.
- ehci_stop() was resetting the host controller when it may have been
running, which the EHCI spec says "may result in undefined behavior".
ehci_stop() was calling port_power() to turn off the ports, which waited
20ms after applying the port change. The msleep was for the case where
the HC might take 20ms to turn the ports on; since we're shutting them
off, we can avoid the msleep and just use ehci_turn_off_ports().
ehci_stop() doesn't need to clear the intr_enable register or revert
ownership of the companion controllers to the BIOS, because the host
controller reset should have done that. There might be a buggy host
controller that doesn't follow the reset rules, but for now we assume
it's redundant code and remove it.
[ A subsequent patch will cancel the timers later ... this version
carries forward existing bugs where timers could get re-armed
after they're canceled. ]
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some EHCI fault paths with large control transfers aren't coded. Avoid
problems by rejecting transfers that may need two qTDs (16+ KB). This is
mostly paranoia; even 4 KB transfers are rare, and most HCDs use lower
limits (so it's unlikely anyone would ever try such a thing).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was pointed out that we found and fixed the cause of the "bogus"
fatal IRQ reports some time ago ... this patch removes the code
which was working around that bug ("status" got clobbered), and a
comment which needlessly confused folk reading this code.
This also includes a minor cleanup to the code which fixed that bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor the EHCI "if (handshake()) state = HC_STATE_HALT" idiom,
which appears 4 times, by replacing it with calls to a new function
called handshake_on_error_set_halt(). Saves a few bytes too.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanups to the EHCI code: revision history is what source
code repositories should have. Switch to a more standard way to
kick in verbose debugging -- don't be EHCI-specific.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Geoff Levand