devm_* APIs are device managed and make code simpler.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to have versioning beyond that for the kernel, especially
when the version number never gets updated.
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1701 has 12 pins that can be configured depending on the system
configuration. Allow settting the corresponding registers from DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The hardware I/O has to be open-coded due to registers of unequal sizes.
Other than that, the transition is straight forward.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1701 has 2 hardware pins to configure the PLL mode in accordance
to the MCLK-to-LRCLK ratio. These pins have to be stable before the chip
is released from reset, and a full reset cycle, including a new firmware
download is needed whenever they change.
This patch adds GPIO properties to the DT bindings of the Codec, and
implements makes the set_sysclk memorize the configured sysclk.
Because the run-time parameters are unknown at probe time, the first
firmware download is postponed to the first hw_params call, when the
driver can determine the mclk/lrclk divider. Subsequent downloads
are only issued when the divider configuration changes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The chip needs a new download after each reset, so the code to do that
needs to live in adau1701_reset().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two alternative modes to start its PWM channels, Mid-Z
and Low-Z. Which one to use depends on how the PWM power stages are
connected to the TAS5086.
This patch adds 6 optional boolean properties to the DT bindings of the
driver which allow the user to configure each individual channel to the
Mid-Z scheme, and leaves all the others to the default (Low-Z).
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two muxes, one for connecting I2S inputs to internal
channels, and another one for selecting which internal channel should
be routed to which PWM output pin.
This patch adds DAPM widgets and routes for this driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add register definitions for input and output mux registers, and rewrite
the tas5086_accessible_reg() function.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to support registers of unequal sizes, the I2C I/O has to be
open-coded.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
To reduce pop noise during playback stream start and stop the codec needs
to have the digital_mute callback implemented.
The codec need to be muted before the CPU dai has been stopped (McPDM).
Stopping the McPDM will generate a pop on the codec since no signal on the
PDM bus means full negative amplitude.
By managing the mute/unmute state of the outputs we can decrease the amount
of pop noise when playback starts or stops.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We need to free the irq at twl6040_remove() which is called when the machine
driver has been removed (the card has been removed).
If we fail to do that, next time when the machine driver is loaded the
codec's probe will fail since the irq has been already requested.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replace the leftover CONFIG_SND_SOC_OMAP_HDMI_CODEC in
sound/soc/omap/Kconfig with CONFIG_SND_SOC_HDMI_CODEC, which was
forgotten in the commit bf7c6e6c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This pull request moves DaVinci EDMA library to
arch/arm/common so it can be used by OMAP based AM335x.
This is a temporary step until all drivers are converted
to use the dmaengine driver in drivers/dma/edma.c.
Several drivers like SPI, MMC/SD have already been converted.
Some like audio are pending.
The other two patches in the pull request are cleanup in nature.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=BH9M
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori:
DaVinci SoC changes for v3.11
This pull request moves DaVinci EDMA library to
arch/arm/common so it can be used by OMAP based AM335x.
This is a temporary step until all drivers are converted
to use the dmaengine driver in drivers/dma/edma.c.
Several drivers like SPI, MMC/SD have already been converted.
Some like audio are pending.
The other two patches in the pull request are cleanup in nature.
* tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: edma: remove unused transfer controller handlers
ARM: davinci: move private EDMA API to arm/common
ARM: davinci: remove __init atrribute from function declaration
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move mach-davinci/dma.c to common/edma.c so it can be used
by OMAP (specifically AM33xx) as well.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Chris Ball <cjb@laptop.org> # davinci_mmc.c
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
[nsekhar@ti.com: dropped davinci sffsdr changes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Commit 75096579c3 ("lib: devres: Introduce devm_ioremap_resource()")
introduced devm_ioremap_resource() and deprecated the use of
devm_request_and_ioremap().
devm_request_mem_region is called in devm_ioremap_resource(). Hence that
part can also be removed.
Since devm_ioremap_resource prints error message on failure, there is
no need to print an explicit warning message.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: alsa-devel@alsa-project.org
CC: Liam Girdwood <lgirdwood@gmail.com>
CC: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
sffsdr machine support does not build since at least v2.6.36
(~3 years). There is little hope of it being fixed, so remove
the support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
support for the DMA40. Now with MUSB and some platform
data removal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=rn7t
-----END PGP SIGNATURE-----
Merge tag 'ux500-dma40-for-arm-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
From Linus Walleij:
Second set of DMA40 changes: refactorings and device tree
support for the DMA40. Now with MUSB and some platform
data removal.
* tag 'ux500-dma40-for-arm-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
dmaengine: ste_dma40: Fetch disabled channels from DT
dmaengine: ste_dma40: Fetch the number of physical channels from DT
ARM: ux500: Stop passing DMA platform data though AUXDATA
dmaengine: ste_dma40: Allow memcpy channels to be configured from DT
dmaengine: ste_dma40_ll: Replace meaningless register set with comment
dmaengine: ste_dma40: Convert data_width from register bit format to value
dmaengine: ste_dma40_ll: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove recently unused stedma40_xfer_dir enums
dmaengine: ste_dma40: Replace ST-E's home-brew DMA direction defs with generic ones
ARM: ux500: Replace ST-E's home-brew DMA direction definition with the generic one
dmaengine: ste_dma40: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove empty function u8500_of_init_devices()
ARM: ux500: Remove ux500-musb platform registation when booting with DT
usb: musb: ux500: add device tree probing support
usb: musb: ux500: attempt to find channels by name before using pdata
usb: musb: ux500: harden checks for platform data
usb: musb: ux500: take the dma_mask from coherent_dma_mask
usb: musb: ux500: move the MUSB HDRC configuration into the driver
usb: musb: ux500: move channel number knowledge into the driver
Reported-by: Dennis May <dennis.may@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This part of bias settings are essential for WM8962 to power up. Without it
"wm8962 0-001a: DC servo timed out" might be prompted due to power-up failure
that happens to FLL if being used.
The driver's also bringing the bias down in the suspend path so it needs to be
powered up in the resume path for symmetry.
According to dapm_pre_sequence_async(), DAPM would call pm_runtime_get_sync()
to let driver finish the bias settings in pm_runtime_resume() before the bias
level being set to STANDBY. So no need to worry about disordered settings for
VMID of WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The power up/down sequence order for DAPM switch widgets is not explicitly
initialized, causing them to be run always as the first widget type for both
power up and down. Move it to the same position in the sequence as other mixer
widget types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 85762e71 ("ASoC: dapm: Implement mixer control sharing") the
long_name field of the snd_soc_dapm_path struct is unused. All of the name
handling now happens entirely in dapm_create_or_share_mixmux_kcontrol(). So we
can remove the long_name field from the snd_soc_dapm_path struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have the same code for freeing a DAPM path in three different locations.
Introduce a new helper function to take care of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The condition 'i == item' is only true when, well, 'i' equals 'item'.
So just use 'item' directly as the index into the array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The private data containing the widget list that is a assigned to a DAPM
kcontrol is never freed. Setup the private_free for DAPM kcontrols to take care
of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The individual component drivers are only useful with a machine driver and
should be selected by the machine drivers so shouldn't have help text of
their own in order to hide them in interactive configuration.
Signed-off-by: Mark Brown <broonie@linaro.org>
In struct snd_soc_card zylonite .owner is assigned THIS_MODULE
twice, remove one of them.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Also fix return values for headphone switch updates.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This fixes:
975:9: sparse: Using plain integer as NULL pointer
1917:24: sparse: symbol 'rt5640_aif_dai_ops' was not declared. Should it be static?
1924:27: sparse: symbol 'rt5640_dai' was not declared. Should it be static?
2079:19: sparse: symbol 'rt5640_i2c_driver' was not declared. Should it be static?
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch that resulted in
bfcc74e (ASoC: SPEAr spdif_{in,out}: use devm for clk and a few
more cleanups)
was broken and applied on a newer tree than it was created for. So
bfcc74e introduced unbalanced clk handling, two warnings about unused
variables and passed 3 arguments to a function only taking 2. This
commit fixes that.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Initially, this binding and driver only describe/support playback to
headphones and speakers.
This driver will support Beaver and Dalmore.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Modify the RT5640 driver to parse platform data from device tree. Write
a DT binding document to describe those properties.
Slight re-ordering of rt5640_i2c_probe() to better fit the DT parsing.
Since ldo1_en is optional, guard usage of it with gpio_is_valid(), rather
than open-coding an if (gpio) check.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Certain use cases may require specific DRE settings so expose control
of these.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the ALC5640 codec driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Implement a DMA slave config prepare routine, as until now the MSP
driver depended on the DMA controller completing the channel
configuration on its own, but this is not the case anymore since the
recent DMA driver updates.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a field with the tx/rx register address to the DMA parameters
structure, and set it to the correct address during device
initialization.
This address used to be hardcoded in the DMA controller driver, it now
needs to be explicitly figured out by the device driver.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move struct ux500_msp_dma_params declaration from ux500_msp_i2s_drvdata
to ux500_msp, this saves some confusing pointer passing and allows to
access all DMA configuration fields from ux500_msp_i2s.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds Kconfig and Makefile to support SPEAr Audio driver.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver is useless if both SPI and I2C are not configured.
Thus don't build this driver if both SPI and I2C are not configured.
This patch silences below build warning if both SPI and I2C are not configured.
CC sound/soc/codecs/adav80x.o
sound/soc/codecs/adav80x.c:842:12: warning: 'adav80x_bus_probe' defined but not used [-Wunused-function]
sound/soc/codecs/adav80x.c:863:12: warning: 'adav80x_bus_remove' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown