Pull ARM fix from Russell King:
"It was noticed that one of Julien's patches contained an error, this
fixes that up"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8810/1: vfp: Fix wrong assignement to ufp_exc
In vfp_preserve_user_clear_hwstate, ufp_exc->fpinst2 gets assigned to
itself. It should actually be hwstate->fpinst2 that gets assigned to the
ufp_exc field.
Fixes commit 3aa2df6ec2 ("ARM: 8791/1:
vfp: use __copy_to_user() when saving VFP state").
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
Use __copy_to_user() rather than __put_user_error() for individual
members when saving VFP state.
This has the benefit of disabling/enabling PAN once per copied struct
intead of once per write.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
__get_user_error() is used as a fast accessor to make copying structure
members in the signal handling path as efficient as possible. However,
with software PAN and the recent Spectre variant 1, the efficiency is
reduced as these are no longer fast accessors.
In the case of software PAN, it has to switch the domain register around
each access, and with Spectre variant 1, it would have to repeat the
access_ok() check for each access.
Use __copy_from_user() rather than __get_user_err() for individual
members when restoring VFP state.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Since commit 799c434154 ("kbuild: thin archives make default for
all archs"), $(AR) is used instead of $(LD) to combine object files.
The following code in arch/arm/vfp/Makefile:
LDFLAGS +=--no-warn-mismatch
... is no longer used.
Also, arch/arm/Makefile already guards arch/arm/vfp/ by a boolean
symbol, CONFIG_VFP, like this:
core-$(CONFIG_VFP) += arch/arm/vfp/
So, $(CONFIG_VFP) is always evaluated to y in arch/arm/vfp/Makefile.
There is no point to use pseudo object, vfp.o, which never becomes
a module. Add all objects to obj-y directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull siginfo updates from Eric Biederman:
"This set of changes close the known issues with setting si_code to an
invalid value, and with not fully initializing struct siginfo. There
remains work to do on nds32, arc, unicore32, powerpc, arm, arm64, ia64
and x86 to get the code that generates siginfo into a simpler and more
maintainable state. Most of that work involves refactoring the signal
handling code and thus careful code review.
Also not included is the work to shrink the in kernel version of
struct siginfo. That depends on getting the number of places that
directly manipulate struct siginfo under control, as it requires the
introduction of struct kernel_siginfo for the in kernel things.
Overall this set of changes looks like it is making good progress, and
with a little luck I will be wrapping up the siginfo work next
development cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
signal/sh: Stop gcc warning about an impossible case in do_divide_error
signal/mips: Report FPE_FLTUNK for undiagnosed floating point exceptions
signal/um: More carefully relay signals in relay_signal.
signal: Extend siginfo_layout with SIL_FAULT_{MCEERR|BNDERR|PKUERR}
signal: Remove unncessary #ifdef SEGV_PKUERR in 32bit compat code
signal/signalfd: Add support for SIGSYS
signal/signalfd: Remove __put_user from signalfd_copyinfo
signal/xtensa: Use force_sig_fault where appropriate
signal/xtensa: Consistenly use SIGBUS in do_unaligned_user
signal/um: Use force_sig_fault where appropriate
signal/sparc: Use force_sig_fault where appropriate
signal/sparc: Use send_sig_fault where appropriate
signal/sh: Use force_sig_fault where appropriate
signal/s390: Use force_sig_fault where appropriate
signal/riscv: Replace do_trap_siginfo with force_sig_fault
signal/riscv: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_mceerr where appropriate
signal/openrisc: Use force_sig_fault where appropriate
signal/nios2: Use force_sig_fault where appropriate
...
Commit 7771c66457 ("signal/arm: Document conflicts with SI_USER and
SIGFPE") broke the siginfo structure for userspace triggered signals,
causing the strace testsuite to regress. Fix this by eliminating
the FPE_FIXME definition (which is at the root of the breakage) and
use FPE_FLTINV instead for the case where the hardware appears to be
reporting nonsense.
Fixes: 7771c66457 ("signal/arm: Document conflicts with SI_USER and SIGFPE")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Call clear_siginfo to ensure every stack allocated siginfo is properly
initialized before being passed to the signal sending functions.
Note: It is not safe to depend on C initializers to initialize struct
siginfo on the stack because C is allowed to skip holes when
initializing a structure.
The initialization of struct siginfo in tracehook_report_syscall_exit
was moved from the helper user_single_step_siginfo into
tracehook_report_syscall_exit itself, to make it clear that the local
variable siginfo gets fully initialized.
In a few cases the scope of struct siginfo has been reduced to make it
clear that siginfo siginfo is not used on other paths in the function
in which it is declared.
Instances of using memset to initialize siginfo have been replaced
with calls clear_siginfo for clarity.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Commit 384b38b669 ("ARM: 7873/1: vfp: clear vfp_current_hw_state
for dying cpu") fixed the cpu dying notifier by clearing
vfp_current_hw_state[]. However commit e5b61bafe7 ("arm: Convert VFP
hotplug notifiers to state machine") incorrectly used the original
vfp_force_reload() function in the cpu dying notifier.
Fix it by going back to clearing vfp_current_hw_state[].
Fixes: e5b61bafe7 ("arm: Convert VFP hotplug notifiers to state machine")
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Setting si_code to 0 results in a userspace seeing an si_code of 0.
This is the same si_code as SI_USER. Posix and common sense requires
that SI_USER not be a signal specific si_code. As such this use of 0
for the si_code is a pretty horribly broken ABI.
Further use of si_code == 0 guaranteed that copy_siginfo_to_user saw a
value of __SI_KILL and now sees a value of SIL_KILL with the result
that uid and pid fields are copied and which might copying the si_addr
field by accident but certainly not by design. Making this a very
flakey implementation.
Utilizing FPE_FIXME, siginfo_layout will now return SIL_FAULT and the
appropriate fields will be reliably copied.
Possible ABI fixes includee:
- Send the signal without siginfo
- Don't generate a signal
- Possibly assign and use an appropriate si_code
- Don't handle cases which can't happen
Cc: Russell King <rmk@flint.arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Ref: 451436b7bbb2 ("[ARM] Add support code for ARM hardware vector floating point")
History Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is good for consistency even if there is no difference in compiled
code. LTO might rely on this eventually. No need to preserve the extern
attribute as it is the default with function prototypes.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Straight forward conversion plus commentary why code which is executed
in hotplug callbacks needs to be invoked before installing them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153335.713612993@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We need to call exit_thread from copy_process in a fail path. So make it
accept task_struct as a parameter.
[v2]
* s390: exit_thread_runtime_instr doesn't make sense to be called for
non-current tasks.
* arm: fix the comment in vfp_thread_copy
* change 'me' to 'tsk' for task_struct
* now we can change only archs that actually have exit_thread
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some platforms might not be able to fully utilize VFP when e.g: one CPU
out of two in a SMP complex lacks a VFP unit. Adding code to migrate
task to the CPU which has a VFP unit would be cumbersome and not
performant, instead, just add the ability to disable VFP.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Convert many (but not all) printk(KERN_* to pr_* to simplify the code.
We take the opportunity to join some printk lines together so we don't
split the message across several lines, and we also add a few levels
to some messages which were previously missing them.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stephen Rothwell reports that commit 3f4c9f8f0a20 ("ARM: 8197/1:
vfp: Fix VFPv3 hwcap detection on CPUID based cpus") introduced a
variable unused warning.
arch/arm/vfp/vfpmodule.c: In function 'vfp_init':
arch/arm/vfp/vfpmodule.c:725:6: warning: unused variable 'mvfr0'
[-Wunused-variable]
u32 mvfr0;
Silence this warning by using IS_ENABLED instead of ifdefs.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The subarchitecture field in the fpsid register is 7 bits wide on
ARM CPUs using the CPUID identification scheme, spanning bits 22
to 16. The topmost bit is used to designate that the
subarchitecture designer is not ARM when it is set to 1. On
non-CPUID scheme CPUs the subarchitecture field is only 4 bits
wide and the higher bits are used to indicate no double precision
support (bit 20) and the FTSMX/FLDMX format (bits 21-22).
The VFP support code only looks at bits 19-16 to determine the
VFP version. On Qualcomm's processors (Krait and Scorpion) we
should see that we have HWCAP_VFPv3 but we don't because bit 22
is set to 1 to indicate that the subarchitecture is not
implemented by ARM and the rest of the bits are left as 0 because
this is the first subarchitecture that Qualcomm has designed.
Unfortunately we can't just widen the FPSID subarchitecture
bitmask to consider all the bits on a CPUID scheme because there
may be CPUs without the CPUID scheme that have VFP without double
precision support and then the version would be a very wrong and
large number. Instead, update the version detection logic to
consider if the CPU is using the CPUID scheme.
If the CPU is using CPUID scheme, use the MVFR registers to
determine what version of VFP is supported. We already do this
for VFPv4, so do something similar for VFPv3 and look for single
or double precision support in MVFR0. Otherwise fall back to
using FPSID to detect VFP support on non-CPUID scheme CPUs. We
know that VFPv3 is only present in CPUs that have support for the
CPUID scheme so this should be equivalent.
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Certain ARM CPU implementations (e.g. Cortex-A15) may not raise a
floating- point exception whenever deprecated short-vector VFP
instructions are executed. Instead these instructions are treated
as UNALLOCATED. Change the VFP exception handling code to emulate
short-vector instructions even if FPEXC exception bits are not
set.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARMv6 and greater introduced a new instruction ("bx") which can be used
to return from function calls. Recent CPUs perform better when the
"bx lr" instruction is used rather than the "mov pc, lr" instruction,
and this sequence is strongly recommended to be used by the ARM
architecture manual (section A.4.1.1).
We provide a new macro "ret" with all its variants for the condition
code which will resolve to the appropriate instruction.
Rather than doing this piecemeal, and miss some instances, change all
the "mov pc" instances to use the new macro, with the exception of
the "movs" instruction and the kprobes code. This allows us to detect
the "mov pc, lr" case and fix it up - and also gives us the possibility
of deploying this for other registers depending on the CPU selection.
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Stephen Warren <swarren@nvidia.com> # Tegra Jetson TK1
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> # mioa701_bootresume.S
Tested-by: Andrew Lunn <andrew@lunn.ch> # Kirkwood
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Tested-by: Tony Lindgren <tony@atomide.com> # OMAPs
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> # Armada XP, 375, 385
Acked-by: Sekhar Nori <nsekhar@ti.com> # DaVinci
Acked-by: Christoffer Dall <christoffer.dall@linaro.org> # kvm/hyp
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> # PXA3xx
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> # Xen
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # ARMv7M
Tested-by: Simon Horman <horms+renesas@verge.net.au> # Shmobile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Undef abort handler in the kernel reads the undefined instruction
from user space. If the page table was modified from another CPU, the
user access could fail and do_page_fault() will be executed with
interrupts disabled. This can potentially deadlock on ARM11MPCore or on
Cortex-A15 with erratum 798181 workaround enabled (both implying IPI for
TLB maintenance with page table lock held).
This patch enables the IRQs in __und_usr before attempting to read the
instruction from user space.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Arun KS <getarunks@gmail.com>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The emulation for single and double precision multiply accumulate
instructions correctly normalised any denormal values in the operand
registers, but failed to normalise the destination (accumulator)
register.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=70501
Signed-off-by: Jay Foad <jay.foad@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch adds asm macros for inc_preempt_count and dec_preempt_count_ti
(which also gets the current thread_info) instead of open-coding them in
arch/arm/vfp/*.S files.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Arun KS <getarunks@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/assembler.h is a better place for this macro since it is used by
asm files outside arch/arm/kernel/
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Arun KS <getarunks@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPU_DYING notifier is called by cpu stopper task which
does not own the context held in the VFP hardware. Calling
vfp_force_reload() has no effect.
Replace it with clearing vfp_current_hw_state.
Signed-off-by: Yuanyuan Zhong <zyy@motorola.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In order to safely support the use of NEON instructions in
kernel mode, some precautions need to be taken:
- the userland context that may be present in the registers (even
if the NEON/VFP is currently disabled) must be stored under the
correct task (which may not be 'current' in the UP case),
- to avoid having to keep track of additional vfpstates for the
kernel side, disallow the use of NEON in interrupt context
and run with preemption disabled,
- after use, re-enable preemption and re-enable the lazy restore
machinery by disabling the NEON/VFP unit.
This patch adds the functions kernel_neon_begin() and
kernel_neon_end() which take care of the above. It also adds
the Kconfig symbol KERNEL_MODE_NEON to enable it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
The support code in vfp_support_entry does not care whether the
exception that caused it to be invoked occurred in kernel mode or
in user mode. However, neither condition that could trigger this
exception (lazy restore and VFP bounce to support code) is
currently allowable in kernel mode.
In either case, print a message describing the condition before
letting the undefined instruction handler run its course and trigger
an oops.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
In order to use the NEON unit in the kernel, we should
initialize it a bit earlier in the boot process so NEON users
that like to do a quick benchmark at load time (like the
xor_blocks or RAID-6 code) find the NEON/VFP unit already
enabled.
Replaced late_initcall() with core_initcall().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Commit d3f79584a8 ("ARM: cleanup undefined instruction entry code")
improved the register scheduling when handling undefined instructions.
A side effect of this is that r5 is now used as a temporary, whilst the
VFP probing code relies on r5 containing a non-zero value when VFP is
not supported.
This patch fixes the VFP detection code so that we don't rely on the
contents of r5. Without this patch, Linux dies loudly on CPUs without
VFP support.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 0cc41e4a21 (arch: remove direct definitions of KERN_<LEVEL>
uses) is broken - not enough thought was put into changing:
.asciz "string"
to
.asciz "string1" "string2"
The problem is that each string gets _separately_ NUL terminated, so
the result is a string containing:
"string1\0string2\0"
rather than:
"string1string2\0"
With our new printk levels, this ends up as - eg, KERN_DEBUG "string":
0x01 0x00 0x07 0x00 "string" 0x00
which produces lots of \x01 in the kernel log.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Martin Storsjö reports that the sequence:
ee312ac1 vsub.f32 s4, s3, s2
ee702ac0 vsub.f32 s5, s1, s0
e59f0028 ldr r0, [pc, #40]
ee111a90 vmov r1, s3
on Raspberry Pi (implementor 41 architecture 1 part 20 variant b rev 5)
where s3 is a denormal and s2 is zero results in incorrect behaviour -
the instruction "vsub.f32 s5, s1, s0" is not executed:
VFP: bounce: trigger ee111a90 fpexc d0000780
VFP: emulate: INST=0xee312ac1 SCR=0x00000000
...
As we can see, the instruction triggering the exception is the "vmov"
instruction, and we emulate the "vsub.f32 s4, s3, s2" but fail to
properly take account of the FPEXC_FP2V flag in FPEXC. This is because
the test for the second instruction register being valid is bogus, and
will always skip emulation of the second instruction.
Cc: <stable@vger.kernel.org>
Reported-by: Martin Storsjö <martin@martin.st>
Tested-by: Martin Storsjö <martin@martin.st>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patrik Kluba reports that the preempt count becomes invalid due
to the preempt_enable() call being unbalanced with a
preempt_disable() call in the vfp assembly routines. This happens
because preempt_enable() and preempt_disable() update preempt
counts under PREEMPT_COUNT=y but the vfp assembly routines do so
under PREEMPT=y. In a configuration where PREEMPT=n and
DEBUG_ATOMIC_SLEEP=y, PREEMPT_COUNT=y and so the preempt_enable()
call in VFP_bounce() keeps subtracting from the preempt count
until it goes negative.
Fix this by always using PREEMPT_COUNT to decided when to update
preempt counts in the ARM assembly code.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reported-by: Patrik Kluba <pkluba@dension.com>
Tested-by: Patrik Kluba <pkluba@dension.com>
Cc: <stable@vger.kernel.org> # 2.6.30
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After commit 846a136881 ("ARM: vfp: fix
saving d16-d31 vfp registers on v6+ kernels"), the OMAP 2430SDP board
started crashing during boot with omap2plus_defconfig:
[ 3.875122] mmcblk0: mmc0:e624 SD04G 3.69 GiB
[ 3.915954] mmcblk0: p1
[ 4.086639] Internal error: Oops - undefined instruction: 0 [#1] SMP ARM
[ 4.093719] Modules linked in:
[ 4.096954] CPU: 0 Not tainted (3.6.0-02232-g759e00b #570)
[ 4.103149] PC is at vfp_reload_hw+0x1c/0x44
[ 4.107666] LR is at __und_usr_fault_32+0x0/0x8
It turns out that the context save/restore fix unmasked a latent bug
in commit 5aaf254409 ("ARM: 6203/1: Make
VFPv3 usable on ARMv6"). When CONFIG_VFPv3 is set, but the kernel is
booted on a pre-VFPv3 core, the code attempts to save and restore the
d16-d31 VFP registers. These are only present on non-D16 VFPv3+, so
this results in an undefined instruction exception. The code didn't
crash before commit 846a136 because the save and restore code was
only touching d0-d15, present on all VFP.
Fix by implementing a request from Russell King to add a new HWCAP
flag that affirmatively indicates the presence of the d16-d31
registers:
http://marc.info/?l=linux-arm-kernel&m=135013547905283&w=2
and some feedback from Måns to clarify the name of the HWCAP flag.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <dave.martin@linaro.org>
Cc: Måns Rullgård <mans.rullgard@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VFPv4 support depends on the VFPv3 context save/restore code, so only
advertise support in the hwcaps if the kernel can actually handle it.
Cc: <stable@vger.kernel.org> # 3.1+
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM fixes from Russell King:
"This fixes various issues found during July"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7479/1: mm: avoid NULL dereference when flushing gate_vma with VIVT caches
ARM: Fix undefined instruction exception handling
ARM: 7480/1: only call smp_send_stop() on SMP
ARM: 7478/1: errata: extend workaround for erratum #720789
ARM: 7477/1: vfp: Always save VFP state in vfp_pm_suspend on UP
ARM: 7476/1: vfp: only clear vfp state for current cpu in vfp_pm_suspend
ARM: 7468/1: ftrace: Trace function entry before updating index
ARM: 7467/1: mutex: use generic xchg-based implementation for ARMv6+
ARM: 7466/1: disable interrupt before spinning endlessly
ARM: 7465/1: Handle >4GB memory sizes in device tree and mem=size@start option
While trying to get a v3.5 kernel booted on the cubox, I noticed that
VFP does not work correctly with VFP bounce handling. This is because
of the confusion over 16-bit vs 32-bit instructions, and where PC is
supposed to point to.
The rule is that FP handlers are entered with regs->ARM_pc pointing at
the _next_ instruction to be executed. However, if the exception is
not handled, regs->ARM_pc points at the faulting instruction.
This is easy for ARM mode, because we know that the next instruction and
previous instructions are separated by four bytes. This is not true of
Thumb2 though.
Since all FP instructions are 32-bit in Thumb2, it makes things easy.
We just need to select the appropriate adjustment. Do this by moving
the adjustment out of do_undefinstr() into the assembly code, as only
the assembly code knows whether it's dealing with a 32-bit or 16-bit
instruction.
Cc: <stable@vger.kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
vfp_pm_suspend should save the VFP state in suspend after
any lazy context switch. If it only saves when the VFP is enabled,
the state can get lost when, on a UP system:
Thread 1 uses the VFP
Context switch occurs to thread 2, VFP is disabled but the
VFP context is not saved
Thread 2 initiates suspend
vfp_pm_suspend is called with the VFP disabled, and the unsaved
VFP context of Thread 1 in the registers
Modify vfp_pm_suspend to save the VFP context whenever
vfp_current_hw_state is not NULL.
Includes a fix from Ido Yariv <ido@wizery.com>, who pointed out that on
SMP systems, the state pointer can be pointing to a freed task struct if
a task exited on another cpu, fixed by using #ifndef CONFIG_SMP in the
new if clause.
Cc: Barry Song <bs14@csr.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ido Yariv <ido@wizery.com>
Cc: Daniel Drake <dsd@laptop.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
vfp_pm_suspend runs on each cpu, only clear the hardware state
pointer for the current cpu. Prevents a possible crash if one
cpu clears the hw state pointer when another cpu has already
checked if it is valid.
Cc: stable@vger.kernel.org
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add #include <linux/kern_levels.h> so that the #define KERN_<LEVEL> macros
don't have to be duplicated.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kay Sievers <kay@vrfy.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ff9a184c ("ARM: 7400/1: vfp: clear fpscr length and stride bits
on entry to sig handler") flushes the VFP state prior to entering a
signal handler so that a VFP operation inside the handler will trap and
force a restore of ABI-compliant registers. Reflushing and disabling VFP
on the sigreturn path is predicated on the saved thread state indicating
that VFP was used by the handler -- however for SMP platforms this is
only set on context-switch, making the check unreliable and causing VFP
register corruption in userspace since the register values are not
necessarily those restored from the sigframe.
This patch unconditionally flushes the VFP state after a signal handler.
Since we already perform the flush before the handler and the flushing
itself happens lazily, the redundant flush when VFP is not used by the
handler is essentially a nop.
Reported-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The vfp_enable function enables access to the VFP co-processor register
space (cp10 and cp11) on the current CPU and must be called with
preemption disabled. Unfortunately, the vfp_init late initcall does not
disable preemption and can lead to an oops during boot if thread
migration occurs at the wrong time and we end up attempting to access
the FPSID on a CPU with VFP access disabled.
This patch fixes the initcall to call vfp_enable from a non-preemptible
context on each CPU and adds a BUG_ON(preemptible) to ensure that any
similar problems are easily spotted in the future.
Cc: stable@vger.kernel.org
Reported-by: Hyungwoo Yang <hwoo.yang@gmail.com>
Signed-off-by: Hyungwoo Yang <hyungwooy@nvidia.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is mainly to get rid of the "vfp_pm_suspend: saving vfp state"
message flooding the kernel message ring by default.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM PCS mandates that the length and stride bits of the fpscr are
cleared on entry to and return from a public interface. Although signal
handlers run asynchronously with respect to the interrupted function,
the handler itself expects to run as though it has been called like a
normal function.
This patch updates the state mirroring the VFP hardware before entry to
a signal handler so that it adheres to the PCS. Furthermore, we disable
VFP to ensure that we trap on any floating point operation performed by
the signal handler and synchronise the hardware appropriately. A check
is inserted after the signal handler to avoid redundant flushing if VFP
was not used.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds