Based on the previous patches from Jesper Dangaard Brouer <hawk@comx.dk>
Implement reading the per queue drop stats register
RQDPC (Receive Queue Drop Packet Count). It counts the number of
packets dropped by a queue due to lack of descriptors available.
Notice RQDPC (Receive Queue Drop Packet Count) stats only gets
incremented, if the DROP_EN bit it set (in the SRRCTL register
for that queue). If DROP_EN bit is NOT set, then the some what
equivalent count is stored in RNBC (not per queue basis).
The RQDPC register is only 12 bit, thus the precision might
suffer due to overrun in-netween the watchdog polling interval.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver is re-registering the DCA requester after every reset.
Instead of doing this we should only be updating the on board DCA registers
and not unregistering/re-registering our requester.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
after the recent changes to wired drivers to use only
netif_carrier_off the driver can have outstanding tx work to
complete that will never complete once link is down. Since the
intel hardware will hold this tx work forever, the driver
notices a tx timeout condition internally and might try
to instigate printk and reset of the part with a
netif_stop_queue, which doesn't work because link is down.
Don't bother arming to tx hang detection when link is down.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup_rctl call was making a call into the ring structure after it had
been freed. This was causing a panic on shutdown. This call wasn't
necessary since it is possible to get the needed index from
adapter->vfs_allocated_count.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An issue was found in which rx checksum could not be enabled without
resetting the interface. The issue was the hardware enable was not being
done via ethtool. To resolve this issue and prevent conflicts with VF
configuration we will leave the feature always enabled in hardware, and
then in software we will choose to ignore the results via a sw flag.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally from: Vlad Yasevich <vladislav.yasevich@hp.com>
This patch, both the driver portion and the sctp code was
modified by Jesse Brandeburg and is
Copyright(c) 2009 Intel Corporation.
Thanks go to Vlad for starting this work.
Intel 82576 chipset supports SCTP checksum offloading. This
patch enables this functionality in the driver. A new NETIF
feature is introduced for SCTP checksum offload. If the driver
supports CRC32c checksum, it can set this feature flag. The
hardware can offload both transmit and receive.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both of these drivers do a check to verify ip_summed is set to
CHECKSUM_UNNECESSARY prior to passing the packet to GRO. GRO itself
already does such a check so it is redundant and can be removed as this
will likely cause out of order issues when receiving a packet that didn't
pass checksum validation.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb driver was being incorrectly setup to only allow disabling receive
checksum if multiqueue was disabled. This change corrects that so that
RXCSUM is configured regardless of queue configuration.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the timeout logic so that it is not possible to have a
sucessful check for message and still return an error if countdown = 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reported-by: Juha Leppanen <juha_motorsportscom@luukku.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb driver was switching between adapter->itr containing the EITR value
and the number of interrupts per second. This resulted in high latencies
being seen after brining the interface down and then back up. To resolve
the issue the itr value will now only contain the value that should be
programmed into EITR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out that the Intel wired ethernet drivers do not need to
wake the tx queue since netif_carrier_on/off will take care of the qdisc
management in order to guarantee the correct handling of the transmit
routine enable state.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is currently dumping a message in the log about failing to
allocate vf data when max_vfs is equal to 0. This change makes it so the
error message is only displayed if we set max_vfs to a non zero value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several unused external references added with the sr-iov
enablement changes. This patch changes all those references to static
local references.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the sysfs entry num_vfs which was added to support
enabling pci virtual functions for 82576.
To prevent VFs from loading automatically a module parameter "max_vfs" was
added so that the number of VFs per PF can be limited. This is especially
useful when 4 or more 82576 ports are on the system because otherwise to
load all VFs would result in 8 interface per physical port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: Fix
Yinghai Lu found one system with 82575EB where, in the kernel that is
kexeced, probe igb failed with -2, the reason being that the adapter
could not be brought back from D3 by the kexec kernel, most probably
due to quirky hardware (it looks like the same behavior happened on
forcedeth).
Prevent igb from putting the adapter into D3 during shutdown except
when we going to power off the system. For this purpose, seperate
igb_shutdown() from igb_suspend() and use the appropriate PCI PM
callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code path for setting up phy loopback testing was out of date and was
setting bits it didn't need to. This change cleans up the code path and
removes some code that has no effect on teh driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the delay for copper phy init from 15ms to 100ms. This is to
address issues seen in which ethtool -t was failing in some cases on 82576
based adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An issue was seen on suspend in which the system reported a page fault. This
was due to the new reg_idx code being called after the queues were freed.
This update prevents any for loops from going through the queues by setting
the number of queues to 0 when they are freed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is on PCIe link trained as x2 the driver is currently reporting
link width as "unknown". The original patch provided by Myron adds the x2
link support and my changes are cosmetic to clean up the readability of the
conditional operators.
Based on work by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb driver was using map_single to map the skbs and then unmap_page to
unmap them. This update changes that so instead uses skb_dma_map and
skb_dma_unmap.
In addition the next_to_watch member of the buffer_info struct was being
set uneccesarily. I removed the spots where it was set without being needed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if there are no multicast addresses programmed into the PF then
the VFs cannot have their multicast filters reset. This change makes it so
the code path that updates vf multicast is always called along with the pf
updates.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb was previously setting up all of the timer members itself. It is
easier to just call setup_timer and reduce the calls to one line.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes IGB_DESC_UNUSED and replaces it with a function call
instead in order to cleanup some of the ugliness introduced by the macro.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the 82575 is fed 802.1q packets, it chokes with
an error of the form:
igb 0000:08:00.1 partial checksum but proto=81!
As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.
There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out with the correct hardware checksum.
Thanks to Kand Ly <kand@riverbed.com> for discovering the
issue and the coming up with a solution. This patch is
based upon his work.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L0s workaround should be moved into a pci quirk and so it is not
necessary in the driver. This update removes the L0s workaround from the
igb driver.
This was the second half of the PCI quirk patch that Matthew Wilcox did
not pick up when he picked up the quirk patch.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 82576 copper adapter and necessary code to restrict wol for
quad port adapter to first port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding device id to support 82576NS dual port copper
NIC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a typo that was doing a less than comparison instead of
a left shift due to the fact that I didn't get enough <'s in there.
This resolves an issue in which vlans were not functioning correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Pf to pool if adding a VLVF register value and the VFTA bit is
already set.
This patch addresses the unlikely situation that the PF adds a vlan
entry when the vlvf is full, and a vf later adds the vlan to the vlvf.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to support wol on the second port for situations such as when the
lan ports are on the motherboard itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DCA is undefined then the adapter struct becomes unnecessary. To
resolve this issue the DCA calls can simply make a call to the adapter
struct through the rx_ring adapter struct member.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_running check in igb poll is a hold over from the use of fake
netdevs to use multiple queues with NAPI prior to 2.6.24. It is no longer
necessary to have the call there and it currently can cause errors if
work_done == budget.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new DCA API, the driver should use dca3_get_tag() instead of
the obsolete dca_get_tag().
Signed-off-by: Maciej Sosnowski < maciej.sosnowski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove skb_orphan call from igb driver as it can cause multiple issues due
to the fact that it is calling the desctructor and removing the skb from
the socket prior to transmission.
The call was added to improve performance but did so by allowing the skb to
be removed from the socket which gave the socket more window space to
transmit. The performance gain is not worth the extra problems that this
kind of workaround can introduce as this could lead to a potential DoS if a
UDP stream decided to monopolize the transmit path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code adds a module parameter called num_vfs which defines if the
driver should attempt to use sr-iov and if so how many VFs should be
enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support to handle requests from the VF to perform
operations such as completing resets, setting/reading mac address, adding
vlans, adding multicast addresses, setting rlpml, and general
communications between the PF and all VFs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the pf portion of vmdq support. This provides enough support so that
VMDq is enabled, and the pf is functional without enabling vfs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first step in supporting sr-iov. The vf_allocated_count value
will be 0 until we actually have vfs present. In the meantime it
represents an offset value for the start of the queues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb is currently not returning the correct values for napi. In addition it
is doing more work than necessary since it will not exit polling until
work_done is equal to zero.
This patch makes the following changes:
1. Consolidates msi-x and non-msi polling routines.
2. Corrects return values for polling routines.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Move variable declaration as far inner as possible.
Fix this sparse warning:
drivers/net/igb/igb_main.c:1895:21: warning: symbol 'j' shadows an earlier one
drivers/net/igb/igb_main.c:1855:16: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To match ixgbe GRO functionality, we remove the LRO (which is now GRO)
Kconfig option which enables GRO by default.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver uses advanced descriptors for its main functionality,
but then uses legacy when testing. This patch changes this so that
advanced descriptors are used throughout and all mentions of legacy
descriptors are removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all of the unused defines from the .h files contained in
igb. For some defines there was a use and so I plugged them into the correct
locations.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch combines a pair of if statements into one.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP Checksum enable doesn't need packet split in order to function. It only
requires the use of advanced descriptors which the current igb driver does.
So we can enable it always without any issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Adaptive Interrupt Moderation algorithm so that the low latency
state is triggered less easily to prevent high interrupt loads.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is intended to hold several whitespace, formatting, and
comment cleanups that have been found while cleaning up the igb driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both TX and RX hardware time stamping are implemented. Due to
hardware limitations it is not possible to verify reliably which
packet was time stamped when multiple were pending for sending; this
could be solved by only allowing one packet marked for hardware time
stamping into the queue (not implemented yet).
RX time stamping relies on the flag in the packet descriptor which
marks packets that were time stamped. In "all packet" mode this flag
is not set. TODO: also support that mode (even though it'll suffer
from race conditions).
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the register definitions and code to read the time
register.
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the version number to 1.3.16 and update copyright dates for 2009.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses two minor items I found while cleaning up the igb
driver for our sourceforge version.
The first clears the context index if we don't flag that we need it.
The second item is that eims_other should be used instead of bit defines
when setting all of the EICS bits prior to reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was seen with repeated interface up/down testing that there was a large
stray between the stats reported by the queues and the stats reported by the
HW. It was found to be an issue in that hw stats were being reset without
first being recorded. This change records the stats before wiping them from
the system via the reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the setting of ring->count variables from igb_probe as they are
duplicating the same configuration that is done igb_alloc_queues.
Remove the err_hw_init tag as it can be replaced by err_sw_init.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The disable_av variable is never used by the driver and provides no value as
it is likely a leftover debugging variable. I have removed it and replaced
the one spot that checked for it with a check for a valid address.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As additional hardware is added to the igb driver it is easier to support
the expansion via switch statements instead of using nested ifs. For
this reason I am changing this to a switch statement.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move igb_get_hw_control up so that it is called just after the reset in
igb_resume. This notifies the HW sooner that the driver is reassuming
control of the device.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt handler was reading eicr and then doing nothing with the
result. I have removed the variable and the register read since they
provide no value to the legacy interrupt handler.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several spots in the code making calls to adapter->hw when they
could have just been accessing hw-> directly. I cleaned up the spots where
this was visibly apparent.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't much point in having the _82575 hanging off the end of this
function since there aren't any other version of this function running
around within this driver. This also allows for a bit of whitespace
cleanup due to a shorter function name.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb watchdog task is modifying the watchdog timer twice duing a single
run. It only needs to be called once to reschedule itself for 2 seconds from
the last time it ran.
In addition I removed the allocation of the mac_info structure since it is
only called twice and is easier to access via the e1000_hw struct.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up igb_netpoll so that it is more friendly with both the
current napi and newly introduced GRO features.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a counter for dma out of sync errors reported via interrupt.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the code for the testing has pretty much become stale at this point
and is need of update. This update just streamlines most of the code,
widens the range of interrupt testing.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is currently using HW_CSUM which is not correct. Update this
to use the IP_CSUM and IPV6_CSUM flags. In addition consolidate the TSO
flag setting.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This statistic is not used and so it is safe to remove
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the nvm ops have the tag _nvm added to the end which is redundant
since all of the calls to the ops have to go through the nvm ops struct
anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames write_phy_reg to write_reg and read_phy_reg to read_reg.
It seems redundant to call out phy in an operation that is part of the
phy_ops struct.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of pulling the mac address from EEPROM it is easier to pull it from
the RAL/RAH registers and then just copy it into the address structures.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes dev_spec a union and simplifies it so that it does not
require dynamic allocation and freeing in the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a link check function to contain all activities related to verifying
that the link is present. The current approach is a bit cludgy and needs
to be cleaned up.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since igb supports only pci-e nics and there is no plan to support any
legacy pci parts in the driver there isn't really much need for checking to
see if an io port is needed.
In the unlikely event that we do begin supporting legacy pci parts then we
can see about adding this code back to the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the initialization of the number of queues into
set_interrupt_capability. This allows the number of queues to increase in
the unlikely event that the system initially fails to allocate enough msi-x
interrupts, does a suspend/resume, and then can allocate enough interrupts
on resume.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
buffsz is being repeatedly set when allocaing buffers. Since this value
should only need to be set once in the function I am moving it out of the
looped portion of the path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While cleaning up the skb_over panic with small frames I found there was
room for improvement in the ordering of operations within the rx receive
flow. These changes will place the prefetch for the next descriptor to a
point earlier in the rx path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using sgmii the link was not being properly passed up to the driver
from the underlying link management functions. This change corrects it so
that get_link_status is cleared when a link has been found.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A panic has been observed with frame sizes smaller than 1K. This has been
root caused to the hardware spanning larger frames across multiple buffers
and then reporting the original frame size in the first descriptor. To
prevent this we can enable set the LPE bit which in turn will restrict
packet sizes to those set in the RLPML register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82576 was being incorrectly flagged as needing a context index. It does not as
each ring has it's own table of 2 contexts.
Driver was registering after registering the driver instead of the other way around.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that a step was missed in the initialization of 82576 fiber nics
that resulted in it not powering on the optics.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igb has flags enabling lltx but this is a holdover from the earlier
e1000 driver which the igb driver was based off of.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes igb invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
Three things of note:
1) I've kept the LRO Kconfig option until we decide to enable
GRO across the board at which point it can also be killed.
2) The poll_controller stuff is broken in igb as it tries to do
the same work as the normal poll routine. Since poll_controller
can be called in the middle of a poll, this can't be good.
I noticed this because poll_controller can invoke the GRO hooks
without flushing held GRO packets.
However, this should be harmless (assuming the poll_controller
bug above doesn't kill you first :) since the next ->poll will
clear the backlog. The only time when we'll have a problem is
if we're already executing the GRO code on the same ring, but
that's no worse than what happens now.
3) I kept the ip_summed check before calling GRO so that we're
on par with previous behaviour.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using "min()", the types of both sides should match. With the cpu
mask changes, the type of num_online_cpus() will now depend on config
options. Use "min_t()" with an explicit type instead.
And make the rx/tx case look the same too, just for sanity.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 82576 adapter orders the queues in pairs when virtualization is in use.
The queue ordering previously conflicted with the ordering when sr-iov was
enabled. This new ordering allows a PF to allocate 2 queues without using
any VF resources.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes tx head writeback as it was found to not provide a
significant improvement in tx performance and on some systems has been seen
to cause a performance degredation due to partial cache line writes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this warning:
drivers/net/igb/e1000_mac.c:54: warning: 'igb_read_pci_cfg' defined but not used
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on Peter Waskiewicz patch for ixgbe. Add error handling based on
Hemminger's recommendation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a virtual environment the ports of an 82575/6 can appear to
be single function devices which is not correct. To resolve this we rely
on the function number stored in the status register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we begin to move into virtualization the use of a global value for
buffer sizes becomes undesirable. This change makes it so only 256 and 512
byte buffers require use of the RCTL register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change interrupt vector naming to match recent changes from Robert Olsson.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the calls necessary to enable advanced error reporting for igb on
systems with AER enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change forces the bits to 0 by using an &= operation with an inverted
mask of all options instead of using an |= with a value of 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a reference to a Buffer Size extention bit that is unneded by
82575/82576 hardware. Since it is not needed it should be removed from the
code.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant argument comments in files of drivers/net/*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the igb driver is experiencing a panic due to a null function
pointer being used during the cleanup of the ethtool looback test on
fiber/serdes parts. This patch prevents that and adds a check prior to
calling any phy function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When suspending the device the ring structure is freed which causes it to
loose track of the count. To resolve this we need to move the ring count
outside of the ring structure and store it in the adapter struct.
In addition to resolving the suspend/resume issue this patch also addresses
issues seen in the event of memory allocation errors causing uneven ring
sizes on multiple queues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This update replaces the xchg calls that were added with a pair of
assignments as there is no need for the xchg calls and they were found to
cause issues on some architectures.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new network device ops interface. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_printk() instead of printk() to give a little more context
and use consistent format.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
igb_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a bool IGB_DCA defined to y if IGB and DCA are enabled, but IGB isn't y while DCA=m. And thus remove the need to select INTEL_IOATDMA when IGB is enabled, so that non-x86 architectures can build the igb driver.
Based on work/patch from Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 82575 has an issue in which the DMA will go out of sync if the link
partner goes into an L0s state. To prevent this we set the pci-e link
partner capability bits to disable the L0s transition on the hw.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove code that was in place to support fake netdev
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The cleaned variable can be replaced by the count of packets cleaned during
the tx interrupt routine so it can be removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Disable support for device 8086:10E8. Currently the result of loading the
driver with the device present causes system instability.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The real_num_tx_queues was not being set when in MSI-X only mode. This patch
corrects that path so all interrupt types are correctly configured.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ethtool -d is reading the EICR and ICR registers which is currently
clearing these registers and masking off interrupts. To prevent this we
read the EICS and ICS equivilents as they can be read without clearing or
masking.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set the EICS bit for each of the RX queues at least once every 2 seconds to
prevent the rx queues from stalling.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
igb_init_managability does not actually perform any function as the two
registers it attempts to write are both read only on the host. This patch
removes the function and all references to it from the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Three functions were left in the code that are no longer used. I am removing
these functions just to keep the code clean.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The igb_mta_set function was not being correctly used
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch changes the PCS configuration for serdes so that the flow
control options change be set via the ethtool -A option.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With a fiber or serdes NIC installed the driver was causing a null pointer
dereference on driver unload.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The internal name was used in comments, replaced with silicon part number.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/net/igb/igb_main.c:388:20: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With the recent changes to tx mutiqueue, igb/ixgbe/e1000e was not calling
netif_tx_start_all_queues() before calling netif_tx_wake_all_queues().
This causes an issue during loading of the driver.
In addition, updated e1000e to use the updated tx mutliqueue api.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This effectively "flips the switch" by making the core networking
and multiqueue-aware drivers use the new TX multiqueue structures.
Non-multiqueue drivers need no changes. The interfaces they use such
as netif_stop_queue() degenerate into an operation on TX queue zero.
So everything "just works" for them.
Code that really wants to do "X" to all TX queues now invokes a
routine that does so, such as netif_tx_wake_all_queues(),
netif_tx_stop_all_queues(), etc.
pktgen and netpoll required a little bit more surgery than the others.
In particular the pktgen changes, whilst functional, could be largely
improved. The initial check in pktgen_xmit() will sometimes check the
wrong queue, which is mostly harmless. The thing to do is probably to
invoke fill_packet() earlier.
The bulk of the netpoll changes is to make the code operate solely on
the TX queue indicated by by the SKB queue mapping.
Setting of the SKB queue mapping is entirely confined inside of
net/core/dev.c:dev_pick_tx(). If we end up needing any kind of
special semantics (drops, for example) it will be implemented here.
Finally, we now have a "real_num_tx_queues" which is where the driver
indicates how many TX queues are actually active.
With IGB changes from Jeff Kirsher.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for a feature bit for something that
can be tested by simply checking the TX queue count.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently VLAN filtering is enabled when the first VLAN is added.
Obviously before that there's no point in receiving any VLAN packets.
Now that we disable VLAN filtering in promiscous mode, we can keep
the VLAN filters enabled the remaining time.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed in this thread:
http://www.mail-archive.com/netdev@vger.kernel.org/msg53976.html
promiscous mode means to disable *all* filters. Currently only unicast
and multicast filtering is disabled. This patch changes all Intel
drivers to also disable VLAN filtering.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve multiqueue performance
Change itr_val to reflect ITR timer value instead of ints/sec
Cleaned up AIM algorithms in general
Based on work by Mitch Williams
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Wrap hw variable declaration in DCA flags to prevent unused variable
warning during compilation.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Updates the suspend and resume to better handle the possibility of MSIX
vector changes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for the use of the inet_lro module to provide
software LRO support.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for page recycling by splitting the page into two
usable portions and tracking the reference count.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change igb from using a series of boolean operators to using a single flags
value that contains a number of different bit flags for all the different
features of the adapter.
This patch also adds WOL support for quad port adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We can remove a clunky workaround for not having the hardware
strip the CRC. 82575 silicon as well as the older PCI Express
e1000e hardware all work OK in this respect.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add DCA support in the similar method that it was added to the ixgbe
driver recently. DCA allows the network device to put data in the
CPU cache and notify the chipset of that event. This reduces cache
misses during receives.
Signed-off-by: Jeb Cramer <cramerj@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Addesses problems seen earlier with igb driver not correctly reporting rx
and tx stats.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This code adds multiple Tx queue infrastructure much like we
previously did in ixgbe. The MSI-X vector mapping is the bulk of
the change.
IAM can now be safely enabled and we've verified that it does
work correctly. We can also eliminate the tx ring lock.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The vlan_hwaccel_{rx,receive_skb} functions expect the full TCI field
for priority mappings, don't truncate the upper 4 bits.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the NAPI implementation to use the new napi_struct infrstructure.
This removes the need of multiple net_device structs to implement a
multiqueue NAPI.
Signed-off-by: PJ Waskiewicz <peter.p.waskiewicz.jr.@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch resolves an issue seen on 82575 adapters with managability
pass-thru enabled, which could cause the system to panic.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Various cosmetic cleanups. Comment fixes. Eliminate the hw part out
of the hw_dbg macro since it's always used.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently there are items in the driver to support parameters, but there
are no parameters being added to the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Function header comments do not match function name.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Simplify a bunch of calls to these functions by moving the adapter
struct out of the function arguments since that is not needed.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
EEPROM access beyond the base eeprom page is unsupported.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes igb driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
EEH is not recovering in a reasonable amount of time on PPC during
igb_down().
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using the new interface for propagating device feature flags into VLAN
deivces, turn on TSO and CSUM offload on VLAN devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To enable EEH support for pci-express network adapters, pcie/msi state
needs to be saved and restored for that adapter.
[after similar patches for ixgbe and e1000e from Wendy Xiong]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We can't look at the socket to get protocol information. We should
instead look directly at the packet, and hope there are no IPv6
option headers.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch eliminates a kernel panic with the igb driver in 2.6.25-rc2 when
running on a Intel 82575 Ethernet controller with a 1000BASE-SX PHY. The
panic does not happen with the 1000BASE-T PHY, only with a SX connection.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I booted an igb kernel with the option pci=nomsi and instantly noticed
that interrupts no longer worked on my igb device. I took a look at the
interrupt initialization and quickly discovered a comment stating:
"DO NOT USE EIAME or IAME in legacy mode"
It seemed a bit odd that bits to enable IAM were being set in legacy
interrupt mode, so I dropped out the following parts and interrupts
began working fine again.
[Updated code flow and a nitpick spelling error --Auke]
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Users reported that ARP's were lost with igb. The problem
is fixed by not enabling this manageability configuration
bit.
None of the release_manageability code is actually needed as the
normal device reset during a shutdown returns everthing to
the right condition automatically.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This removes a sparse warning.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are pleased to announce a new Gigabit Ethernet product and its
driver to the linux community. This product is the Intel(R) 82575
Gigabit Ethernet adapter family. Physical adapters will be available
to the public soon. These adapters come in 2- and 4-port versions
(copper PHY) currently. Other variants will be available later.
The 82575 chipset supports significantly different features that
warrant a new driver. The descriptor format is (just like the
ixgbe driver) different. The device can use multiple MSI-X vectors
and multiple queues for both send and receive. This allows us to
optimize some of the driver code specifically as well compared to
the e1000-supported devices.
This version of the igb driver no lnger uses fake netdevices and
incorporates napi_struct members for each ring to do the multi-
queue polling. multi-queue is enabled by default and the driver
supports NAPI mode only.
All the namespace collisions should be gone in this version too. The
register macro's have been condensed to improve readability.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer