* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - touchpad driver miss-recognising logitech mice
Input: synaptics - ensure we reset the device on resume
Input: usbtouchscreen - fix eGalax HID ignoring
Input: ambakmi - fix timeout handling in amba_kmi_write()
Input: pxa930_trkball - fix write timeout handling
Input: struct device - replace bus_id with dev_name(), dev_set_name()
Input: bf54x-keys - fix debounce time validation
Input: spitzkbd - mark probe function as __devinit
Input: omap-keypad - mark probe function as __devinit
Input: corgi_ts - mark probe function as __devinit
Input: corgikbd - mark probe function as __devinit
Input: uvc - the button on the camera is KEY_CAMERA
Input: psmouse - make MOUSE_PS2_LIFEBOOK depend on X86
Input: atkbd - make forced_release_keys[] static
Input: usbtouchscreen - allow reporting calibrated data
This patch updates the maple bus to support asynchronous block reads
and writes as well as generally improving the quality of the code and
supporting concurrency (all needed to support the Dreamcast visual
memory unit - a driver will also be posted for that).
Changes in the bus driver necessitate some changes in the two maple bus
input drivers that are currently in mainline.
As well as supporting block reads and writes this code clean up removes
some poor handling of locks, uses an atomic status variable to serialise
access to devices and more robusly handles the general performance
problems of the bus.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
X86_PC is the only remaining 'sub' architecture, so we dont need
it anymore.
This also cleans up a few spurious references to X86_PC in the
driver space - those certainly should be X86.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A pointer to spitzkbd_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
[dtor@mail.ru: fixed some more section markups]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A pointer to omap_kp_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
[dtor@mail.ru: fixed some more section markups]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A pointer to corgikbd_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
[dtor@mail.ru: fixed some more section markups]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: i8042 - add Dell Vostro 1510 to nomux list
Input: gtco - use USB endpoint API
Input: add support for Maple controller as a joystick
Input: atkbd - broaden the Dell DMI signatures
Input: HIL drivers - add MODULE_ALIAS()
Input: map_to_7segment.h - convert to __inline__ for userspace
Input: add support for enhanced rotary controller on pxa930 and pxa935
Input: add support for trackball on pxa930 and pxa935
Input: add da9034 touchscreen support
Input: ads7846 - strict_strtoul takes unsigned long
Input: make some variables and functions static
Input: add tsc2007 based touchscreen driver
Input: psmouse - add module parameters to control OLPC touchpad delays
Input: i8042 - add Gigabyte M912 netbook to noloop exception table
Input: atkbd - Samsung NC10 key repeat fix
Input: atkbd - add keyboard quirk for HP Pavilion ZV6100 laptop
Input: libps2 - handle 0xfc responses from devices
Input: add support for Wacom W8001 penabled serial touchscreen
Input: synaptics - report multi-taps only if supported by the device
Input: add joystick driver for Walkera WK-0701 RC transmitter
...
It is always "an" if there is a vowel _spoken_ (not written).
So it is:
"an hour" (spoken vowel)
but
"a uniform" (spoken 'j')
Signed-off-by: Frederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
Some Dells need the dell input quirk applied but have a different vendor
string in their DMI tables. Add an extra entry to cover these machines as
well.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add MODULE_ALIAS() to the HIL keyboard (hil_kbd.c) and HIL mouse
(hil_ptr.c) drivers to make kernel module autoloader functional.
Report HIL port number ID in serio id.id field.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add clock framework support to the sh_mobile keysc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the key repeat issue with the Fn+F? keys on the new
Samsung NC10 Netbook, so that the keys can be defined and used within
ACPID correctly, otherwise the keys repeat indefinately.
This solves part of http://bugzilla.kernel.org/show_bug.cgi?id=12021
Signed-off-by: Stuart Hopkins <stuart@dodgy-geeza.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add quirk for misbehaving volume buttons on HP Pavilion ZV6100 laptop which
are not sending keyrelease events, as reported by Aaron Pickett.
Signed-off-by: Rikard Ljungstrand <lrikard@student.chalmers.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Have most uses of OMAP_GPIO_IRQ() use gpio_to_irq() instead.
Calls used for table initialization are left alone, at least
this time around.
(This patch is for code in both the OMAP tree and mainline.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add support for new USB Tablet PCs
Input: replace spin_lock_bh with spin_lock_irqsave in ml_ff_playback
Input: i8042 - add Compal Hel80 laptop to nomux blacklist
Input: cm109 - add keymap for ATCom AU-100 phone
Input: fix the example of an input device driver
Input: psmouse - fix incorrect validate_byte check in OLPC protocol
Input: atkbd - cancel delayed work before freeing its structure
Input: atkbd - add keymap quirk for Inventec Symphony systems
Input: i8042 - add Dell XPS M1530 to nomux list
Input: elo - fix format string in elo driver
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pointed out by Oleg Nesterov. Since delayed work is used here, use of
flush_scheduled_work() is not sufficient in atkbd_disconnect(). It does
not wait for scheduled delayed work to finish. This patch prevents
delayed work to be processed after freeing atkbd structure (used struct
delayed_work is part of atkbd) by cancelling this delayed work.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Zepto 6615WD laptop (rebranded Inventec Symphony system) needs a
key release quirk for its volume keys to work. The attached patch adds
the quirk to the atkbd driver.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=460237
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is no reason to limit the GPIO rows to 6 for OMAP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The GPIO interrupts are disabled several times after the first key press.
No need to disable - again - the interrupts in the omap_kp_scan_keypad
function on OMAP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a flag to gpio-key driver to turn on the input subsystems
auto repeat feature if needed.
Signed-off-by: Dominic Curran <dcurran@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (32 commits)
Input: wm97xx - update email address for Liam Girdwood
Input: i8042 - add Thinkpad R31 to nomux list
Input: move map_to_7segment.h to include/linux
Input: ads7846 - fix cache line sharing issue
Input: cm109 - add missing newlines to messages
Input: document i8042.debug in kernel-parameters.txt
Input: keyboard - fix potential out of bound access to key_map
Input: psmouse - add OLPC touchpad driver
Input: psmouse - tweak PSMOUSE_DEFINE_ATTR to support raw set callbacks
Input: psmouse - add psmouse_queue_work() for ps/2 extension to make use of
Input: psmouse - export psmouse_set_state for ps/2 extensions to use
Input: ads7846 - introduce .gpio_pendown to get pendown state
Input: ALPS - add signature for DualPoint found in Dell Latitude E6500
Input: serio_raw - allow attaching to translated (SERIO_I8042XL) ports
Input: cm109 - don't use obsolete logging macros
Input: atkbd - expand Latitude's force release quirk to other Dells
Input: bf54x-keys - add power management support
Input: atmel_tsadcc - improve accuracy
Input: convert drivers to use strict_strtoul()
Input: appletouch - handle geyser 3/4 status bits
...
This updates most of the OMAP drivers which are in mainline to switch to
using the cross-platform GPIO calls instead of the older OMAP-specific
ones.
This is all fairly brainless/obvious stuff. Probably the most interesting
bit is to observe that the omap-keypad code seems to now have a portable
core that could work with non-OMAP matrix keypads. (That would improve
with hardware IRQ debouncing enabled, of course...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dell laptops fail to send key up events for several of their special
keys. There's an existing quirk in the kernel to handle this, but it's
limited to the Latitude range. This patch extends it to cover all
portable Dells.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix Bug: does nor properply resume after suspend mem
Fix for PM_SUSPEND_MEM: Save and restore peripheral base registers
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
strict_strtoul() allows newline character at the end of the the input
string and therefore is more user-friendly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: evdev - fix printf() format for sizeof
Input: remove version.h from drivers that don't need it
Input: cobalt_btns - add missing MODULE_LICENSE
If a driver dies not use LINUX_VERSION_CODE nor KERNEL_VERSION
then it does not need to include version.h
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xilinx_ps2 - fix warning
Input: bcm5974 - implement autosuspend support
Input: bcm5974 - add driver for Macbook Air and Pro Penryn touchpads
Input: paper over a bug in Synaptics X driver
Input: evdev - split EVIOCGBIT handlig into a separate function
Input: i8042 - Add Dritek quirk for Acer TravelMate 4280
Input: xpad - add Pelican Eclipse D-Pad to the list of devices
Input: gpio-keys - make gpio_keys_device_driver static
Input: gpio-keys - fix possible NULL pointer dereference
Input: wm97xx - enable sub-drivers by default
For now this only saves a few instructions (for gpio_keys_report_event,
gpio_keys_isr and gpio_check_button one instraction each on ARM using
arm-linux-gnu-gcc 4.2.3---I assume this is similar for other arch/compiler
combinations).
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
By passing a gpio_button_data structure to the handler instead of the
whole platform_device the search for the right button can go away.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We can simply wrap in to the dev_set/get_drvdata(), there's no reason
to track an extra level of private data on top of the struct device.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were completely inconsistent. Clean these up to take a maple_driver
pointer directly for consistency.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Have a single probe function instead of a probe and a connect function.
Also tidy a comment.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Allow the removal (and subsequent reinsertion) of the maple_keyb (maple
keyboard) driver by adding a working removal function.
Also tidy long lines.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes the sparse warning
symbol 'gpio_keys_device_driver' was not declared. Should it be static?
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
bdata->button is used in gpio_check_button but never initialized. Having a
device with debounce_interval != 0 without this patch resulted on an oops on
my machine.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove request_mem_region() and release_mem_region() from sh_keysc driver.
Those functions can find resource conflict, but it is already checked in
platform_device_add().
Signed-off-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These files use semaphores but don't include semaphore.h
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
According to the tests in do_initcalls(), the proper error code in case no
device is found is -ENODEV, not -ENXIO or -EIO.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Video switch key on HP 2133 doesn't send release event, so we
have to create workaround similar to what we do for Dell Latitude,
i.e. perform DMI match for the system and generate 'false' release
event ourselves, so that userspace doesn't think that the key is
stuck forever.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since some of the keycodes defined in input.h have values greater
than 255 we should use unsigned shorts in keymaps.
Tested-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. Set input bits for direct keys codes
2. Set input bits for rotary encoder codes only if rotary
encoder is enabled
3. Enable EV_REL only if rotary encoder is enabled and rel_codes
are set up
Signed-off-by: Antonio Ospite <ao2@openezx.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
... and we have few enough places using the latter to make it
simpler to do search and replace...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some input drivers do not check whether they're actually running on the
correct platform, causing multi-platform kernels to crash if they are not.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since 43cc71eed1, the platform modalias
is prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable
"input" platform drivers, to re-enable auto loading.
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
of the PXA register definitions
2. this is actually a temporary move in the transition of PXA2xx to
use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid double free situation from happening by removing input_free_device()
after input_unregister_device(). Suggested by Dmitry Torokhov.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a platform driver for the SuperH KEYSC block. The driver expects to get
mode, timing information and keypad layout from the board code as platform
data. The board code is resonsible for pin configuration.
Both sh7343 and sh7722 should be supported, but only the sh7722 processor has
been tested so far. SH_KEYSC_MODE_3 is yet to be tested.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the following build warning:
drivers/input/keyboard/omap-keypad.c: In function 'omap_kp_probe':
drivers/input/keyboard/omap-keypad.c:418: warning: 'row_idx' is used uninitialized in this function
drivers/input/keyboard/omap-keypad.c:421: warning: 'col_idx' is used uninitialized in this function
These variables are useful when cpu_is_omap24xx(), and otherwise just
for useless cleanup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cleanup IRQ handling in gpio_keys: bail after handling the IRQ, and
report IRQ_NONE if we never handle it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Enables the Sharp Zaurus Collie and Poodle devices to be turned off
by pressing the "Cancel" button for a few seconds (as designed by
Sharp).
Additional small cleanups:
- removal of unused #defines and variables
- add missing __devinit/__devexit/__devinitconst annotations
- reorganized copyright notice
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We want to mask (key_number - 1), not key_number. The current
implementation works fine for all values but the maximum one,
i.e. 8.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, only one debounce_interval is introduced for both direct and
matrix keys. This is true in most cases, although the keypad controller
supports different debounce for direct/matrix keys.
Some platforms do require this to be tuned, instead of the default
reset value of 100ms.
Rotary encoder will always use zero debounce time for now to achieve
certain sensitivity.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. use ioremap() for registers access, this improves the portability
of the driver (e.g. same IP on different processor with different
I/O memory range), and make it possible to remove those registers
definition in pxa-regs.h as PXA is undergoing a clean-up of that
header file
2. use device specific IRQ instead of hardcoded IRQ_KEYPAD, same
reason as above
3. clean up the error handling path in _probe()
4. remove DRIVER_NAME and use pdev->name when necessary, we don't
actually need a constant string literals
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. Rotary encoder events can be configured either as relative events
as the legacy code does or as any specified key code, this is
useful on some platform which uses the rotary keys as
KEY_{UP/DOWN/LEFT/RIGHT}
2. Add support for direct keys, the corresponding keycodes for each
direct key can now be specified within the platform data
3. Remove the direct/rotary key detection code from the IRQ handler
to dedicated functions to improve readability
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Introduce pxa27x_keypad_config() for keypad registers configuration
and remove the reg_kpc, reg_kprec from platform data structure
so that configurations of keypad registers can be centralized to a
single function.
It can also be re-used when resuming.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. Introduce the "struct pxa27x_keypad" structure for driver specific
information, such as "struct clk", generated matrix key codes and
so on
2. Use KEY() macro to define matrix keys, instead of original 8x8 map
this makes definition easier with keypad where keys are sparse
3. Keep a generated array in "struct pxa27x_keypad" for fast lookup
4. Separate the matrix scan into a dedicated function for readability
and report only those keys whose state has been changed, instead
of report all states
5. Make use of KPAS to decide the faster path if only one key has been
detected
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The pin configurations will slowly be moved to the board specific code
at initialization thus to make the driver more generic.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The controller should really be called keypad, and also align
the naming of functions and structures to use "pxa27x_keypad"
as prefix, instead of "pxakbd".
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add keyboard support on tosa (Sharp Zaurus SL-6000x).
Largely based on patches by Dirk Opfer.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Drop #include <linux/moduleparam.h> in files that also include
linux/module.h, since module.h includes moduleparam.h already.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Most of Fn+F? special keys on (at least) the Dell Latitude laptops don't
generate a hardware key release event so the driver has to generate one.
Signed-off-by: Giel de Nijs <giel@caffeinetrip.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The spitz keyboard driver reports KEY_SUSPEND events but doesn't
register its use of this event in the keybit bitfield, breaking
input events for this key. This patch fixes that by registering
the key in the keybit bitfield.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes the HP Jornada 6xx keyboard default keymap which had some
bad keymap values. This resulted in wrong key being returned when pressed
(for example, key 'y' returned 'r').
Also, while we are at it lets arrange the include files in alphabetical order.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, gpio_keys.c assumes the GPIOs to be already properly configured;
this patch changes gpio-keys to perform explicit calls to gpio_request() and
gpio_configure_input().
This matches the behaviour of leds-gpio.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
get rid of input BIT* duplicate defines
use newly global defined macros for input layer. Also remove includes of
input.h from non-input sources only for BIT macro definiton. Define the
macro temporarily in local manner, all those local definitons will be
removed further in this patchset (to not break bisecting).
BIT macro will be globally defined (1<<x)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: <dtor@mail.ru>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: <lenb@kernel.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: <perex@suse.cz>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <vernux@us.ibm.com>
Cc: <malattia@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (95 commits)
[ARM] 4578/1: CM-x270: PCMCIA support
[ARM] 4577/1: ITE 8152 PCI bridge support
[ARM] 4576/1: CM-X270 machine support
[ARM] pxa: Avoid pxa_gpio_mode() in gpio_direction_{in,out}put()
[ARM] pxa: move pxa_set_mode() from pxa2xx_mainstone.c to mainstone.c
[ARM] pxa: move pxa_set_mode() from pxa2xx_lubbock.c to lubbock.c
[ARM] pxa: Make cpu_is_pxaXXX dependent on configuration symbols
[ARM] pxa: PXA3xx base support
[NET] smc91x: fix PXA DMA support code
[SERIAL] Fix console initialisation ordering
[ARM] pxa: tidy up arch/arm/mach-pxa/Makefile
[ARM] Update arch/arm/Kconfig for drivers/Kconfig changes
[ARM] 4600/1: fix kernel build failure with build-id-supporting binutils
[ARM] 4599/1: Preserve ATAG list for use with kexec (2.6.23)
[ARM] Rename consistent_sync() as dma_cache_maint()
[ARM] 4572/1: ep93xx: add cirrus logic edb9307 support
[ARM] 4596/1: S3C2412: Correct IRQs for SDI+CF and add decoding support
[ARM] 4595/1: ns9xxx: define registers as void __iomem * instead of volatile u32
[ARM] 4594/1: ns9xxx: use the new gpio functions
[ARM] 4593/1: ns9xxx: implement generic clockevents
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
Input: use full RCU API
Input: remove tsdev interface
Input: add support for Blackfin BF54x Keypad controller
Input: appletouch - another fix for idle reset logic
HWMON: hdaps - switch to using input-polldev
Input: add support for SEGA Dreamcast keyboard
Input: omap-keyboard - don't pretend we support changing keymap
Input: lifebook - fix X and Y axis range
Input: usbtouchscreen - add support for GeneralTouch devices
Input: fix open count handling in input interfaces
Input: keyboard - add CapsShift lock
Input: adbhid - produce all CapsLock key events
Input: ALPS - add signature for ThinkPad R61
Input: jornada720_kbd - send MSC_SCAN events
Input: add support for the HP Jornada 7xx (710/720/728) touchscreen
Input: add support for HP Jornada 7xx onboard keyboard
Input: add support for HP Jornada onboard keyboard (HP6XX)
Input: ucb1400_ts - use schedule_timeout_uninterruptible
Input: xpad - fix dependancy on LEDS class
Input: auto-select INPUT for MAC_EMUMOUSEBTN option
...
Resolved conflicts manually in drivers/hwmon/applesmc.c: converting from
a class device to a device and converting to use input-polldev created a
few apparently trivial clashes..
Atari keyboard: incorporate additional review comments:
o Kill reference to source file name
o Return error value from input_register_device() instead of -ENOMEM
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Michael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver's keymap is a mix of hardware codes and keycodes and so
may not be used with default implementations of getkeycode() and
setkeycode().
Also some whitespace cleanup.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds suspend/resume support and enables wakeup from
gpio_keys buttons.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As David Brownell pointed out, gpio_keys driver does not check
return code of gpio_to_irq().
This patch adds the gpio_to_irq return code check to gpio_keys
and moves the IRQ edge type setting to request_irq flags to avoid
changing the irq type before we have confirmed we can use it.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
WWW/Homepage key on Microsoft-compatible keyboards generates KEY_WWW
when connected via PS/2 port but KEY_HOMEPAGE when connected via USB.
This patch changes mapping in atkbd to match one in HID driver.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: document some of keycodes
Input: add a new EV_SW SW_RADIO event, for radio switches on laptops
Input: serio - take drv_mutex in serio_cleanup()
Input: atkbd - use printk_ratelimit for spurious ACK messages
Input: atkbd - throttle LED switching
Input: i8042 - add HP Pavilion ZT1000 to the MUX blacklist
On some boxes keyboard controllers are too slow to withstand
continuous flow of requests to turn keyboard LEDs on and off
and start losing some keypresses or even all of them.
Delay executing of LED switching request if we had another one
within 50 ms thus easing load on the controller.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Not directly related to x86, but I got tired of seeing these warnings on every
kconfig update when building on a non m68k box:
drivers/input/keyboard/Kconfig:170:warning: 'select' used by config symbol 'KEYBOARD_ATARI' refers to undefined symbol 'ATARI_KBD_CORE'
drivers/input/mouse/Kconfig:182:warning: 'select' used by config symbol 'MOUSE_ATARI' refers to undefined symbol 'ATARI_KBD_CORE'
I moved the definition of ATARI_KBD_CORE into drivers/input/keyboard/Kconfig
so it's always seen by Kconfig.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CKEN macro definitions no longer contains the bit number; remove it
from usages in the pxa27x keyboard driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input: (65 commits)
Input: gpio_keys - add support for switches (EV_SW)
Input: cobalt_btns - convert to use polldev library
Input: add skeleton for simple polled devices
Input: update some documentation
Input: wistron - fix typo in keymap for Acer TM610
Input: add input_set_capability() helper
Input: i8042 - add Fujitsu touchscreen/touchpad PNP IDs
Input: i8042 - add Panasonic CF-29 to nomux list
Input: lifebook - split into 2 devices
Input: lifebook - add signature of Panasonic CF-29
Input: lifebook - activate 6-byte protocol on select models
Input: lifebook - work properly on Panasonic CF-18
Input: cobalt buttons - separate device and driver registration
Input: ati_remote - make button repeat sensitivity configurable
Input: pxa27x - do not use deprecated SA_INTERRUPT flag
Input: ucb1400 - make delays configurable
Input: misc devices - switch to using input_dev->dev.parent
Input: joysticks - switch to using input_dev->dev.parent
Input: touchscreens - switch to using input_dev->dev.parent
Input: mice - switch to using input_dev->dev.parent
...
Fixed up conflicts with core device model removal of "struct subsystem" manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Atari keyboard and mouse support.
(reformating and Kconfig fixes by Roman Zippel)
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IRQF_DISABLED is the proper name.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_keys driver is wrongly ARM-specific; it can't build on
other platforms with GPIO suport. This fixes that problem.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ben Nizette <ben.nizette@iinet.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.
So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing. Currently that's a bunch of
ARMs, and AVR32; more are on the way.
It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: <raph@8d.com>
Cc: <msvoboda@ra.rockwell.com>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- mark some structures const or __read_mostly
- hilkbd.c: fix uninitialized spinlock in HIL keyboard driver
- hil_mlc.c: use USEC_PER_SEC instead of 1000000
- hp_sdc: bugfix for request_irq()/free_irq() parameters, this prevented
multiple load/unload cycles as module
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not call release_region() if the code has been compiled
without CONFIG_HP300 support.
Signed-off-by: Cyrill V. Gorcunov <gorcunov@gmail.com>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds support for at least SA1100 and S3C24xx CPUs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The obsolete SA_xxx interrupt flags have been used despite the scheduled
removal. Fixup the remaining users in -mm.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also some whitespace cleanup.
Signed-off-by: Cyrill V. Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is an interrupt-driven keyboard driver for simple buttons
connected directly to CPU GPIO lines of embedded ARM systems.
It supports pxa architectures and is used by a number of PDAs
and PocketPC phones in the handhelds.org kernel. Support for
other architectures, such as sa11xx and sc2410, will be added
once generic GPIO API is available.
Signed-off-by: Paul Sokolovsky <pmiscml@gmail.com>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
"sunkbd_enable(sunkbd, 0);" has no effect. Adding "sunkbd->enabled =
enable" in sunkbd_enable (obvious)
Signed-off-by: Fabrice Knevez <nuxdoors@cegetel.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that it's built on m68k too...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The bus for this was removed entirely some time ago, as well as most
of the drivers that referenced it. maple_keyb seems to have been the
odd one out, and was still sitting in the source tree (though not
actually part of the build system). Kill off the rest of it..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The keyboard is connected via GPIOs to the processor, and scanned
using a column sample register. The hardware provides no debouncing
mechanism, so the state of the keys is read KBDSCAN_STABLE_COUNT
times before being reported to the input layer.
The status of the keys needs to be polled because there is no
interrupt hooked to the lines. A workqueue is used for this.
Signed-off-by: Nicolas Bellido Y Ortega <ml@acolin.be>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.
For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.
To make this work, an extra flag is introduced into the management side of the
work_struct. This governs auto-release of the structure upon execution.
Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function. This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated.. This is a
problem if the auxiliary data is taken away (as done by the last patch).
However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems. But then the work function must itself release the
work_struct by calling work_release().
In most cases, automatic release is fine, so this is the default. Special
initiators exist for the non-auto-release case (ending in _NAR).
Signed-Off-By: David Howells <dhowells@redhat.com>
I moved to a different town and my old snail-mail address is invalid
now. Also, there's no need at all to have any address like that in
the sources, so remove it completely.
Signed-off-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
The Zaurii drivers were partially fixed up for the IRQ register
changes, but unfortunately missed some bits, resulting in build
errors. Fix these.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many users seems to be annoyed by this warning so kill the message
and implement a counter exported as a sysfs attribute so we still
know what is going on. Make atkbd use attribute groups while we are
at it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Enable HIL configuration options on HP300
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: wistron - add support for Acer TravelMate 2424NWXCi
Input: wistron - fix setting up special buttons
Input: add KEY_BLUETOOTH and KEY_WLAN definitions
Input: add new BUS_VIRTUAL bus type
Input: add driver for stowaway serial keyboards
Input: make input_register_handler() return error codes
Input: remove cruft that was needed for transition to sysfs
Input: fix input module refcounting
Input: constify input core
Input: libps2 - rearrange exports
Input: atkbd - support Microsoft Natural Elite Pro keyboards
Input: i8042 - disable MUX mode on Toshiba Equium A110
Input: i8042 - get rid of polling timer
Input: send key up events at disconnect
Input: constify psmouse driver
Input: i8042 - add Amoi to the MUX blacklist
Input: logips2pp - add sugnature 56 (Cordless MouseMan Wheel), cleanup
Input: add driver for Touchwin serial touchscreens
Input: add driver for Touchright serial touchscreens
Input: add driver for Penmount serial touchscreens
...
This patch adds support for keypad driver running on different TI
OMAP(http://www.ti.com/omap) processor based boards like OSK, H2, H3, H4,
Persuas and Nokia 770.
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for stowaway and stowaway compatible (eg. dicota inutPDA)
serial keyboards. Reported to work on palm zire71 and palm tungsten T3.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Microsoft Natural Elite Pro keyboard produces unisual response to
the GET ID command - single byte 0xaa (normally keyboards produce
2-byte response). Fail GET ID command so atkbd gets a change to
do alternate probe.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This was introduced in commit 3d0f0fa0cb554541e10cb8cb84104e4b10828468:
bounds checking is performed against period[32] while indexing delay[4].
Spotted by Coverity, CID 1376.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make atkbd report HANGEUL/HANJA keys by default and use correct scan
codes for these keys (they were swapped). Also make sure their scancodes
reported as EV_MSC/MSC_SCAN events.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix a mispelling of the korean alphabet name in the input subsystem.
See http://en.wikipedia.org/wiki/Hangeul#Names for more details.
KEY_HANGUEL left to not break people
Signed-off-by: Jerome Pinot <ngc891@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dump the extra mapping in the amikbd interrupt handler, so old Amiga keymaps
work again. Amigas need a special keymap anyway, standard keymaps are not
usable and recreating all keymaps is simply not worth the trouble.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the numbered SW_* entries from the input system and assign names
to the existing users.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On Thu, Mar 30, 2006 at 08:31:02AM -0500, Dmitry Torokhov wrote:
> Don't do that, its double free. input_unregister_device() normally
> causes release() to be called and free the device. input_free_device
> is only to be called when input_register_device has not been called or
> failed.
>
> Plus you might want to unregister device after closing serio port,
> otherwise your interrupt routine might be referencing already freed
> memory.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
* Change the scan interval from 100ms to 50ms. This stops the key
repeat from triggering on double letter presses.
* Remove unneeded stale hinge code from corgikbd
* Change unneeded corgi GPIO pins to inputs when suspended
* Add support for the headphone jack switch for both corgi and spitz
(as switch SW_2)
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allow disabling atkbd driver if CONFIG_EMBEDDED is enabled. Previously
it was impossible to disable atkbd on X86_PC.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not activate softrepeat by default on dumb keyboards as it clashes
with their own hardware repeat (for example Dell DRAC3). Softrepeat
can still be activated manually via module parameter or sysfs.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix bat_xl and err_xl logic causing atkbd to complain about 'unknown
key 0x7f'. Noted by Ben LaHaise.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
98kbd{,-io} and 98spkr all went out with PC98 subarch. Remove stale Makefile
entries that remained.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
These haven't worked in some time, and we've dropped support for the bus
from the SH tree until someone shows some interest in maintaining it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call serio_reconnect() instead of serio_rescan() when detecting that
a new keyboard was plugged in. This should help KVM uses losing custom
keymap settings when switching between boxes.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Changing led state is pretty slow operation; when there are multiple
requests coming at a high rate they may interfere with normal typing.
Try optimize (skip) changing hardware state when multiple requests
are coming back-to-back.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
* Hide debugging code into #ifdef, which allows to simplify
the large switch statement
* Update macros to not reference variables not given as
arguments
Signed-off-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PC is left-over cruft after the introduction of CONFIG_X86_PC with
the subarch split. Remove it, and fixup the remaining users to depend on
CONFIG_X86_PC instead.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update drivers to new input layer changes.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Reorder code in gscps2_interrupt() and only enable ports when opened.
This fixes issues with hangs booting an SMP kernel on my C360.
Previously serio_interrupt() could be called before the lock in
struct serio was initialised.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Fix up users of ->hpa to use ->hpa.start instead.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make /sys/bus/parisc/drivers look better by cleaning up parisc_driver
names.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This fixes depenencies of collie keyboard.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Correct the right shift key entry in the spitz keyboard driver.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a input driver for the keyboard found on the Zaurus Cxx00 series (Spitz,
Akita, Borzoi). Its based on corgikbd but there are enough subtle differences
to justify a separate driver.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The corgi keyboard has need of a switch event type with slightly type to the
input system as recommended by the input maintainer.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The input system handles key state tracking so there's no need for the driver
to do so as well. Also tidy up some comment formatting and remove a now
unneeded function.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add some power management code to the corgi keyboard driver so that only one
power event gets reported within any reasonable time frame and the driver
doesn't enter an infinte loop due to key repeat.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a couple of compile errors in the corgi keyboard driver.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend bat_xl handling to do err_xl handling, so that
keyboards using 0x7f scancode for regular keys can work.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch disables the scroll feature on AT keyboards by default, because
it causes the numbers of mouse devices to shift, breaking user setups.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
as function keys instead of special keys.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes two possible off by one errors found by the Coverity
checker (look at the period[i] and delay[j] in the two first unchanged
lines).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Daniel Mierswa