Driver must assign the user supplied compare/swap values in
the wqe to successfully complete the atomic compare and
swap operation.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Once a cmd to FW times out(after 20s) it is reasonable to
assume the FW or atleast the control path is dead.
No point issuing further cmds to the FW as each subsequent cmd
with another 20s timeout will cascade resulting in unnecessary
traces and/or NMI Lockups.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The MTU value in the qplib_qp.mtu should be
consistent with whatever mtu was set during
INIT to RTR.The Next PSN and number of packets
are calculated based on this member in the qplib_qp structure.
Signed-off-by: Narender Reddy <narender.reddy@broadcom.com>
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit 24587380f6 ("parisc: Add MADV_HWPOISON and MADV_SOFT_OFFLINE") added
the necessary constants to handle hardware-poisoning. Those were needed to
support the page deallocation feature from firmware.
But I completely missed to add the relevant fault handler code. This now
showed up when I ran the madvise07 testcase from the Linux Test Project,
which failed with a kernel BUG at arch/parisc/mm/fault.c:320.
With this patch the parisc kernel now behaves like other platforms and
gives the same kernel syslog warnings when poisoning pages.
Signed-off-by: Helge Deller <deller@gmx.de>
While scanning the PDT for reported broken memory modules, warn if the
initrd was coincidentally loaded into bad memory.
Signed-off-by: Helge Deller <deller@gmx.de>
According to the programming note at page 1-31 of the PA 1.1 Firmware
Architecture document, one should use the PDC_INSTR firmware function to
get the instruction that invokes a PDCE_CHECK in the HPMC handler. This
patch follows this note and sets the instruction which has been a nop up
until now.
Testing on a C3000 and C8000 showed that this firmware call isn't
implemented on those machines, so maybe it's only needed on older ones.
Signed-off-by: Helge Deller <deller@gmx.de>
Check stack pointer if we are reaching the stack end and stop unwinding
if we do. This fixes early backtraces and avoids showing unrealistic
call stacks.
Signed-off-by: Helge Deller <deller@gmx.de>
The parisc architecture has larger stack frames than most other
architectures on 32-bit kernels.
Increase the maximum allowed stack frame to 1280 bytes for parisc to
avoid warnings in the do_sys_poll() and pat_memconfig() functions.
Signed-off-by: Helge Deller <deller@gmx.de>
During OpenMPI scale up testing, we observe rdma_connect
failures if ports are reused on multiple connections.
This is because the Control Queue-Pair (CQP) command to add
the reused port to Accelerated Port Bit VectorTable (APBVT)
fails as there already exists an entry.
Check for duplicate port before invoking the CQP command
to add APBVT entry and delete the entry only if the port
is not in use.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the VLAN priority which is in the upper 3 bits of the VLAN
tag field in the QP context.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If QP modify to closing/terminate/error fails, connection is
not torn down as there is no corresponding asynchronous
event that will initiate the teardown.
Add explicit call to i40iw_cm_disconn if not waiting in
modify QP, otherwise schedule it in CM timer.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Check number of available MSI-X vectors for i40iw.
If there are no available vectors, fail the open.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Reduce stack size by dynamically allocating memory instead
of declaring large struct on the stack:
drivers/infiniband/hw/bnxt_re/ib_verbs.c: In function ‘bnxt_re_query_qp’:
drivers/infiniband/hw/bnxt_re/ib_verbs.c:1600:1: warning: the frame size of 1216 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If delay_drop_debugfs_init() fails in any of the operations to create
debugfs, it is calling delay_drop_debugfs_cleanup() as part of its
cleanup. But delay_drop_debugfs_cleanup() checks for 'dbg' and since
we have not yet pointed 'dbg' to the debugfs we need to cleanup, the
cleanup fails and we are left with stray debugfs elements and also a
memory leak.
Fixes: 4a5fd5d296 ("IB/mlx5: Add necessary delay drop assignment")
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the case where mbox_status is OCRDMA_MBX_STATUS_FAILED and
add_status is OCRDMA_MBX_STATUS_FAILED err_num is assigned -EAGAIN
however the case OCRDMA_MBX_STATUS_FAILED is missing a break and
falls through to the default case which then re-assigns err_num
to -EFAULT. Fix this so that err_num is assigned to -EAGAIN
for the add_status OCRDMA_MBX_STATUS_FAILED case and -EFAULT
otherwise.
Detected by CoverityScan CID#703125 ("Missing break in switch")
Fixes: fe2caefcdf ("RDMA/ocrdma: Add driver for Emulex OneConnect IBoE RDMA adapter")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
IPoIB doesn't support transport/rnr retry schemes as per
RFC so those errors are expected. No need to flood the
log files with them.
Tested-by: Michael Nowak <michael.nowak@oracle.com>
Tested-by: Rafael Alejandro Peralez <rafael.peralez@oracle.com>
Tested-by: Liwen Huang <liwen.huang@oracle.com>
Tested-by: Hong Liu <hong.x.liu@oracle.com>
Reviewed-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Reported-by: Rajiv Raja <rajiv.raja@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The original 20ms delay is only marginally enough delay after a block write
operation during firmware update. Let's increase the delay to ensure that
the controller finishes up storing the page to avoid failures in the
firmware updates.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a listen create fails, then the server tid (stid) is incorrectly left
in the stid idr table, which can cause a touch-after-free if the stid
is looked up and the already freed endpoint is touched. So make sure
and remove it in the error path.
Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the thread waiting for a CLOSE_LISTSRV_RPL times out and bails,
then we need to handle a subsequent CPL if it arrives and the stid has
been released. In this case silently drop it.
Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The listening endpoint should always be dereferenced at the end of
pass_accept_req().
Fixes: f86fac79af ("RDMA/iw_cxgb4: atomic find and reference for listening endpoints")
Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJZxSV8AAoJELDendYovxMvf5YH/jUEgeFVgP0KRjNsvgp4gu88
4BW7nWYtFt4gGE1KnrKEPbg5Je0OwkpW7vUXxvLwDGWymtHMzVuuB2xxwzkePyzS
17Kzmb/JiuaNpVF4+5v3JvAw3b9iHrZ7T6cXOQgm28agd3m/y+9FSyzoMoNNRdGG
xURwUyK1idRqtkQV5VsQAK0Z1lVF7YhhaxWXBtClsqnKWoeLBLc8fpRJmUNruA33
E2Sdi06mNNN3xudu1s2edC5hAO4EgVKmonnmyHRYonIYwuqSND8fhEXj+PRdHj7s
lLVRQixd3raBiSscLASaQ7I/66frBm+TXzmoHAVtYkdlXBJlisTIvQlMPtAwu60=
=c3HX
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.14b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"A fix for a missing __init annotation and two cleanup patches"
* tag 'for-linus-4.14b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen, arm64: drop dummy lookup_address()
xen: don't compile pv-specific parts if XEN_PV isn't configured
xen: x86: mark xen_find_pt_base as __init
Four fixes for the new instruction emulation code. A fix for CPU offline on bare
metal machines when certain idle states are not supported, and a fix for a
device_node refcounting oops during CPU hotplug, caused by recent changes.
Going to stable are a fix for an oops during core dump on machines that have TM
(Transactional Memory) disabled. Reordering some EEH initialisation to avoid
trashing memory, and another device_node refcounting fix.
And a few other minor things.
Thanks to:
Anton Blanchard, Benjamin Herrenschmidt, Cyril Bur, Gautham R. Shenoy, Gustavo
Romero, Kamalesh Babulal, Matthew Weber, Matt Weber, Naveen N. Rao, Nicholas
Piggin, Pavithra Prakash, Ravi Bangoria, Ronak Desai, Scott Wood, Tyrel
Datwyler.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Eiyz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"It turns out our single-fix pull from last week was too good to be
true. I missed a few fixes in that pull that had already come in
because I was on leave, but also we hadn't found the bugs yet. So this
week it's a bit bigger, though not ridiculous. Hopefully things will
settle down from here on.
Four fixes for the new instruction emulation code. A fix for CPU
offline on bare metal machines when certain idle states are not
supported, and a fix for a device_node refcounting oops during CPU
hotplug, caused by recent changes.
Going to stable are a fix for an oops during core dump on machines
that have TM (Transactional Memory) disabled. Reordering some EEH
initialisation to avoid trashing memory, and another device_node
refcounting fix.
And a few other minor things.
Thanks to: Anton Blanchard, Benjamin Herrenschmidt, Cyril Bur, Gautham
R. Shenoy, Gustavo Romero, Kamalesh Babulal, Matthew Weber, Matt Weber,
Naveen N. Rao, Nicholas Piggin, Pavithra Prakash, Ravi Bangoria, Ronak
Desai, Scott Wood, Tyrel Datwyler"
* tag 'powerpc-4.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Fix parent_dn reference leak in add_dt_node()
powerpc/pseries: Fix "OF: ERROR: Bad of_node_put() on /cpus" during DLPAR
powerpc/eeh: Create PHB PEs after EEH is initialized
powerpc/kprobes: Update optprobes to use emulate_update_regs()
powerpc/powernv: Clear LPCR[PECE1] via stop-api only for deep state offline
powerpc/sstep: mullw should calculate a 64 bit signed result
powerpc/sstep: Fix issues with mcrf
powerpc/sstep: Fix issues with set_cr0()
powerpc/tm: Flush TM only if CPU has TM feature
powerpc/sysrq: Fix oops whem ppmu is not registered
powerpc/configs: Update for CONFIG_SND changes
powerpc/e6500: Update machine check for L1D cache err
Pull MIPS fixes from Ralf Baechle:
- Fix a build error on MSP71xx which used to rely on somehow magically
<asm/setup.h> being pulled in which no longer happens.
- Fix the __write_64bit_c0_split inline assembler where there was the
theoretical possibility of GCC interpret the constraints such that
bad code could result.
- A __init was causing section mismatch errors on Alchemy. Just to be
on the safe side, Manuel's patch does away with all of them.
- Fix perf event init.
* '4.14-fixes' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: PCI: fix pcibios_map_irq section mismatch
MIPS: Fix input modify in __write_64bit_c0_split()
MIPS: MSP71xx: Include asm/setup.h
MIPS: Fix perf event init
Pull s390 fixes from Martin Schwidefsky:
- A couple of bug fixes: memory management, perf, cio, dasd and
scm_blk.
- A larger change in regard to the CPU topology to improve performance
for systems running under z/VM or KVM.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/topology: enable / disable topology dynamically
s390/topology: alternative topology for topology-less machines
s390/mm: fix write access check in gup_huge_pmd()
s390/mm: make pmdp_invalidate() do invalidation only
s390/cio: recover from bad paths
s390/scm_blk: consistently use blk_status_t as error type
s390/dasd: fix race during dasd initialization
s390/perf: fix bug when creating per-thread event
Free memory region, if arm_pmu_acpi_probe is not successful.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
of_pci_iommu_init() tries to be clever and stop its alias walk at the
device represented by master_np, in case of weird PCI topologies where
the bridge to the IOMMU and the rest of the system is not at the root.
It turns out this is a bit short-sighted, since there are plenty of
other callers of pci_for_each_dma_alias() which would also need the same
behaviour in that situation, and the only platform so far with such a
topology (Cavium ThunderX2) already solves it more generally via a PCI
quirk. As this check is effectively redundant, and returning a boolean
value as an int is a bit broken anyway, let's just get rid of it.
Reported-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Fixes: d87beb7492 ("iommu/of: Handle PCI aliases properly")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some Intel host controllers (e.g. CNP) use an ACPI device-specific method
to ensure correct voltage switching. Fix voltage switch for those, by
adding a call to the DSM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some change for v4.14 broke the debug output for TMIO. But since it was
not helpful to me and too noisy for my taste anyhow, let's just remove
it instead of fixing it. We'll find something better if we'd need it...
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In linux-4.13, Wei worked hard to convert dst to a traditional
refcounted model, removing GC.
We now want to make sure a dst refcount can not transition from 0 back
to 1.
The problem here is that input path attached a not refcounted dst to an
skb. Then later, because packet is forwarded and hits skb_dst_force()
before exiting RCU section, we might try to take a refcount on one dst
that is about to be freed, if another cpu saw 1 -> 0 transition in
dst_release() and queued the dst for freeing after one RCU grace period.
Lets unify skb_dst_force() and skb_dst_force_safe(), since we should
always perform the complete check against dst refcount, and not assume
it is not zero.
Bugzilla : https://bugzilla.kernel.org/show_bug.cgi?id=197005
[ 989.919496] skb_dst_force+0x32/0x34
[ 989.919498] __dev_queue_xmit+0x1ad/0x482
[ 989.919501] ? eth_header+0x28/0xc6
[ 989.919502] dev_queue_xmit+0xb/0xd
[ 989.919504] neigh_connected_output+0x9b/0xb4
[ 989.919507] ip_finish_output2+0x234/0x294
[ 989.919509] ? ipt_do_table+0x369/0x388
[ 989.919510] ip_finish_output+0x12c/0x13f
[ 989.919512] ip_output+0x53/0x87
[ 989.919513] ip_forward_finish+0x53/0x5a
[ 989.919515] ip_forward+0x2cb/0x3e6
[ 989.919516] ? pskb_trim_rcsum.part.9+0x4b/0x4b
[ 989.919518] ip_rcv_finish+0x2e2/0x321
[ 989.919519] ip_rcv+0x26f/0x2eb
[ 989.919522] ? vlan_do_receive+0x4f/0x289
[ 989.919523] __netif_receive_skb_core+0x467/0x50b
[ 989.919526] ? tcp_gro_receive+0x239/0x239
[ 989.919529] ? inet_gro_receive+0x226/0x238
[ 989.919530] __netif_receive_skb+0x4d/0x5f
[ 989.919532] netif_receive_skb_internal+0x5c/0xaf
[ 989.919533] napi_gro_receive+0x45/0x81
[ 989.919536] ixgbe_poll+0xc8a/0xf09
[ 989.919539] ? kmem_cache_free_bulk+0x1b6/0x1f7
[ 989.919540] net_rx_action+0xf4/0x266
[ 989.919543] __do_softirq+0xa8/0x19d
[ 989.919545] irq_exit+0x5d/0x6b
[ 989.919546] do_IRQ+0x9c/0xb5
[ 989.919548] common_interrupt+0x93/0x93
[ 989.919548] </IRQ>
Similarly dst_clone() can use dst_hold() helper to have additional
debugging, as a follow up to commit 44ebe79149 ("net: add debug
atomic_inc_not_zero() in dst_hold()")
In net-next we will convert dst atomic_t to refcount_t for peace of
mind.
Fixes: a4c2fd7f78 ("net: remove DST_NOCACHE flag")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Reported-by: Paweł Staszewski <pstaszewski@itcare.pl>
Bisected-by: Paweł Staszewski <pstaszewski@itcare.pl>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given NR_IRQS is 2048 on sparc64, and even 32784 on alpha, 3 digits is
not enough to represent interrupt numbers on all architectures. Hence
PHY interrupt numbers may be truncated during printing.
Increase the buffer size from 4 to 8 bytes to fix this.
Fixes: 5e369aefdc ("net: stmmac: Delete dead code for MDIO registration")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull libnvdimm fixes from Dan Williams:
"A crash fix and corresponding regression test enabling for the crash
scenario. The unit test for this crash is available in ndctl-v58.2.
This branch has received a build success notification from the
0day-kbuild robot over 148 configs. The fix is tagged for -stable /
backport to 4.13"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, namespace: fix btt claim class crash
tools/testing/nvdimm: disable labels for nfit_test.1
The clock-cell size is 1 on stm32h7 plaform.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Fixes: 3e4d618b07 ("clk: stm32h7: Add stm32h743 clock driver")
Signed-off-by: Rob Herring <robh@kernel.org>
Normally, when input device supporting force feedback effects is being
destroyed, we try to "flush" currently playing effects, so that the
physical device does not continue vibrating (or executing other effects).
Unfortunately this does not work well for uinput as flushing of the effects
deadlocks with the destroy action:
- if device is being destroyed because the file descriptor is being closed,
then there is noone to even service FF requests;
- if device is being destroyed because userspace sent UI_DEV_DESTROY,
while theoretically it could be possible to service FF requests,
userspace is unlikely to do so (they'd need to make sure FF handling
happens on a separate thread) even if kernel solves the issue with FF
ioctls deadlocking with UI_DEV_DESTROY ioctl on udev->mutex.
To avoid lockups like the one below, let's install a custom input device
flush handler, and avoid trying to flush force feedback effects when we
destroying the device, and instead rely on uinput to shut off the device
properly.
NMI watchdog: Watchdog detected hard LOCKUP on cpu 3
...
<<EOE>> [<ffffffff817a0307>] _raw_spin_lock_irqsave+0x37/0x40
[<ffffffff810e633d>] complete+0x1d/0x50
[<ffffffffa00ba08c>] uinput_request_done+0x3c/0x40 [uinput]
[<ffffffffa00ba587>] uinput_request_submit.part.7+0x47/0xb0 [uinput]
[<ffffffffa00bb62b>] uinput_dev_erase_effect+0x5b/0x76 [uinput]
[<ffffffff815d91ad>] erase_effect+0xad/0xf0
[<ffffffff815d929d>] flush_effects+0x4d/0x90
[<ffffffff815d4cc0>] input_flush_device+0x40/0x60
[<ffffffff815daf1c>] evdev_cleanup+0xac/0xc0
[<ffffffff815daf5b>] evdev_disconnect+0x2b/0x60
[<ffffffff815d74ac>] __input_unregister_device+0xac/0x150
[<ffffffff815d75f7>] input_unregister_device+0x47/0x70
[<ffffffffa00bac45>] uinput_destroy_device+0xb5/0xc0 [uinput]
[<ffffffffa00bb2de>] uinput_ioctl_handler.isra.9+0x65e/0x740 [uinput]
[<ffffffff811231ab>] ? do_futex+0x12b/0xad0
[<ffffffffa00bb3f8>] uinput_ioctl+0x18/0x20 [uinput]
[<ffffffff81241248>] do_vfs_ioctl+0x298/0x480
[<ffffffff81337553>] ? security_file_ioctl+0x43/0x60
[<ffffffff812414a9>] SyS_ioctl+0x79/0x90
[<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71
Reported-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Reported-by: Clément VUCHENER <clement.vuchener@gmail.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=193741
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Ursula Braun says:
====================
net/smc: bug fixes 2017-09-20
here is a collection of small smc-patches built for net fixing
smc problems in different areas.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Usually socket closing is delayed if there is still data available in
the send buffer to be transmitted. If a process is killed, the delay
should be avoided.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of outstanding work requests is limited. If all work
requests are in use, tx processing is postponed to another scheduling
of the tx worker. Switch to a delayed worker to have a gap for tx
completion queue events before the next retry.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An out-of-sync condition can just be detected by the client.
If the server receives a CLC DECLINE message indicating an out-of-sync
condition for the link groups, the server must clean up the out-of-sync
link group.
There is no need for an extra third parameter in smc_clc_send_decline().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Client link group creation always follows the server linkgroup creation.
If peer creates a new server link group, client has to create a new
client link group. If peer reuses a server link group for a new
connection, client has to reuse its client link group as well. This
patch introduces a longer delay for client link group removal to make
sure this link group still exists, once the peer decides to reuse a
server link group. This avoids out-of-sync conditions for link groups.
If already scheduled, modify the delay.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The solicited flag is meaningful for the receive completion queue.
Ask for next work completion of any type on the send queue.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc_pnet_fill_entry() uses dev_get_by_name() adding a refcount to ndev.
The following smc_pnet_enter() has to reduce the refcount if the entry
to be added exists already in the pnet table.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc_netinfo_by_tcpsk() looks up the routing cache. Such a lookup requires
protection by an RCU read lock.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMC receive function currently lacks a timeout check under the
condition that no data were received and no data are available. This
patch adds such a check.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devesh Sharma