Durations can never be negative, so it makes sense to consistently use
unsigned int for LIRC transmission. Contrary to the initial impression,
this shouldn't actually change the userspace API.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Solve the ./scripts/checkpatch.pl compliants for the patches
that added xc4000 support, including a few changes at dib0700.
While here, remove a few printk noise by converting some msgs
into debug ones.
Cc: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed the use of 'card_type' from the tuner configuration structure, and
replaced it with separate parameters to set board-specific configuration.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enabled code to check if the version of the firmware reported by the hardware
is correct after uploading it.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Automatically select the xc4000 module for dib0700 if the tuner selection is
not customized.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Various coding style changes:
- removed unused / commented out code
- changed C++ style comments to C format
- renamed functions and variables that included upper case letters in the name
- removed tabs from module parameter descriptions
- replaced the use of XC_RESULT_* with standard error codes
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added code to detect the XC4100 chip, which is presumably an analog-only
"value" version of the XC4000. It is not sure, however, if any devices
using this have actually been produced and sold, so the patch may be
unneeded.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch causes the tuner reset command to be ignored in the firmware
code, since this only happens when the BASE/INIT1 firmware is loaded by
check_firmware(), and in that case check_firmware() already calls the
reset callback before starting to load the firmware.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Minor coding changes related to the xc_tune_channel() function.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch implements support for analog TV and FM radio.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'audio_std' module parameter makes it possible to fine tune
some audio related aspects of the driver, like setting the exact
audio standard (NICAM, A2, etc.) to be used for some video standards.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements setting the registers in xc4000_set_params()
and xc4000_set_analog_params(). A new register is defined which enables
filtering of the composite video output (this is needed to avoid bad
picture quality with some boards).
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch makes a few minor changes to the printing
of debug messages, and reporting the tuner status. The 'debug'
module parameter can now be set from 0 to 2 to control the
verbosity of debug messages.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes/cleans up the loading of the firmware file when the
driver is loaded and initialized.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch implements the xc4000_sleep() function.
The 'no_powerdown' module parameter is now interpreted differently:
- 0 uses a device-specific default
- 1 disables power management like before
- 2 enables power management
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for selecting a card type in struct
xc4000_config, to allow for implementing some card specific code
in the driver.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes the following fixes in check_firmware():
- there is only one BASE and INIT1 firmware for XC4000
- loading SCODE is needed also for FM radio
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed unused code from load_scode() (all SCODE firmwares are
assumed to have the HAS_IF bit set).
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The firmware_name module parameter makes it possible to set the firmware
file name. It defaults to "xc4000.fw" if not specified.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc_get_frequency_error() function reported the frequency error
incorrectly. The data read from the hardware is a signed integer, in
15625 Hz units. The attached patch fixes the bug.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a mutex to xc4000_priv, to protect the driver
from being accessed by multiple processes at the same time.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch implements support for DVB-T with 7 MHz bandwidth.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes the following changes to the standards table:
- added 'u16 int_freq' to struct XC_TV_STANDARD (needed for analog TV
and radio, 0 for DVB-T)
- added new standard for SECAM-D/K video with PAL-D/K audio
- the 'int_freq' values are now specified in the table
- changed VideoMode for NTSC and PAL-B/G standards
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the first of a set of patches that update the original xc4000
sources to my modified version. It removes some unused code, and makes
a few minor formatting changes.
[mchehab@redhat.com: re-add XC_TUNE_ANALOG/XC_TUNE_DIGITAL constants, to avoid compilation breakage]
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove some inline comments I had written from when I was computing the proper
dib7000p configuration to work with the xc4000.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove some printk() calls added during driver development, and demote some
other messages to debug only (to reduce dmesg chatter).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Give the xc4000 firmware filename a filename that makes more sense for public
release.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't dump debug into to dmesg by default (something I had enabled during
bringup of the xc4000 driver).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixup the PLL and AGC configs so that the 340e works (correcting errors I made
when I did the original config blindly).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove a hack I had put in to force the firmware to be 8MHz, now setting
the firmware properly based on the target standard.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on a reference trace under Windows, reverse engineer the PLL config.
Note that the xtal is not yet setup, and the timf cannot be determined yet
because my reference trace doesn't actually achieve a signal lock.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was confirmed by DibCom that i2c stretching is broken in the i2c master
on the dib7700. So we need to put a hack into the xc4000 driver to not
complain in certain very specific cases where we know i2c stretching occurs.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setup a proper AGC config for the 340e, based on the Windows USB trace
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove hard-coded references to 5400, using the value passed in when the
xc4000 is attached.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly setup the standard firmware loading and scode loading, as well as
getting rid of a ton of dead code. Note that I am getting a single i2c
error when the standard firmware sets the video standard, but everything else
seems to be loading properly now.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code to handle firmware blobs for the standard and scode. Note there
appears to be some issue with loading the DTV8 standard firmware, probably
related to direct/indirect mode.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we use the xc3028 version of the firmware file parsing routine (which
includes support for scodes and separate blobs), we can drop the xc5000
version of the code.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc4000 driver is based on the original xc5000 driver, and while the
xc5000 supports the XREG_BUSY register, the xc4000 does not. So remove the
code in question.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to set the firmware type properly in order to locate the init1
firmware.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc3028 version does i2c splitting in a different manner than xc4000 and
xc5000, so reuse the xc5000 version of the routine (the key here being that
xc4000 expects the first *two* bytes to be the same for splitting transactions.
Doing it the xc3028 way was resulting in i2c errors partially through the
firmware load. With this change, it would appear that the entire base firmware
is being loaded successfully (product id now properly shows 0x0FA0).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch over to using the firmware management routines from the tuner-xc2028,
since that has support for scodes, etc.
This code still requires signficant cleanup, and at this point the base
firmware does not load properly (i2c write errors about 300 bytes in).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to set the dev.parent member on the dib7000p on its i2c master, or
else calls to request_firmware() will hit an oops in 2.6.31.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a sleep since in some cases the dib7000p wasn't online when being probed.
The optimal timing has not yet been determined.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the correct i2c bus to communicate with the tuner, and properly setup the
reset GPIO and i2c address.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide a frontend setup routine for the PCTV 340e which takes into account
the specific GPIO setup of the board.
Note that this patch does *not* take into account the xc4000 reset pin, which
is attached to the dib7000.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the board profile for the PCTV 340eSE, since that's what I have here
for development.
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver. I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Davide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The implementation of the gain calculation for this sensor is incorrect.
It is only working for the first 127 values.
The reason is, that the gain cannot be set directly by writing a value
into the gain registers of the sensor. The gain register work this way
(see datasheet page 24): bits 0 to 6 are called "initial gain". These
are linear. But bits 7 and 8 ("analog multiplicative factors") and bits
9 and 10 ("digital multiplicative factors") work completely different:
Each of these bits increase the gain by the factor 2. So if the bits
7-10 are 0011, 0110, 1100 or 0101 for example, the gain from bits 0-6 is
multiplied by 4. The order of the bits 7-10 is not important for the
resulting gain. (But there are some recommended values for low noise)
The current driver doesn't do this correctly: If the current gain is 000
0111 1111 (127) and the gain is increased by 1, you would expect the
image to become brighter. But the image is completly dark, because the
new gain is 000 1000 0000 (128). This means: Initial gain of 0,
multiplied by 2. The result is 0.
This patch adds a new function which does the gain calculation and also
fixes the same bug for red_balance and blue_balance. Additionally, the
driver follows the recommendation from the datasheet, which says, that
the gain should always be above 0x0020.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are problems when you use this camera/sensor in a very bright room
or outside. The image is completely white, because it is overexposed.
The driver uses a default value which is not suitable for all
environments.
This patch makes it possible to adjust the exposure time by youself. I
found out by logging the i2c-data, that the windows driver for this
sensor is doing this, too. I tested the camera on a sunny day and after
adjusting the exposure time, I was able to see a very good image.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the datasheet (page 8), the first optical clear
pixel-column is not at position 14. The correct/recommended value is 20.
Without this patch there is a dark line on the left side of the image.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The conversion of winbond-cir to use rc-core seems to have missed a
a few bits and pieces which were in my local tree. Kudos to
Juan Jesús García de Soria Lucena <skandalfo@gmail.com> for noticing.
[mchehab@redhat.com: fix two UTF-8 violations]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the original code, if the allocation failed we dereference "rr3"
when it was NULL.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If change_protocol() fails and we goto out_raw, then it calls unlock
twice. I noticed that the other time we called change_protocol() we
held the &dev->lock, so I changed it to hold it here too.
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Otherwise they clutter the dmesg buffer even on a production kernel.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function "rc5_scan" in "dvb_usb.h" is returning invalid value.
The value should be returned "u16" but is returning "u8".
See example below in "drivers/media/dvb/dvb-usb/opera1.c":
send_key = (send_key & 0xffff) | 0x0100;
for (i = 0; i < ARRAY_SIZE(rc_map_opera1_table); i++) {
if (rc5_scan(&rc_map_opera1_table[i]) == (send_key & 0xffff)) {
*state = REMOTE_KEY_PRESSED;
*event = rc_map_opera1_table[i].keycode;
opst->last_key_pressed =
rc_map_opera1_table[i].keycode;
break;
}
opst->last_key_pressed = 0;
}
Signed-off-by: Manoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert radio-sf16fmr2 to use generic TEA575x implementation. Most of the
driver code goes away as SF16-FMR2 is basically just a TEA5757 tuner
connected to ISA bus.
The card can optionally be equipped with PT2254A volume control (equivalent
of TC9154AP) - the volume setting is completely reworked (with balance control
added) and tested.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The info and err macros are already defined by the USB stack. Rename
these macros to avoid macro redefinition warnings.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dbg, warn and info macros are already defined by the USB stack.
Rename these macros to avoid macro redefinition warnings.
Refactor lineshift in printouts.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
radio->int_in_urb is not deallocated on error paths in si470x_usb_driver_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On function videobuf_pages_to_sg the statement sg_set_page(&sglist[0],
pages[0], PAGE_SIZE - offset, offset) will fail if size is less than
PAGE_SIZE.
Signed-off-by: Newson Edouard <newsondev@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
list_first_entry() always returns non-null here. I think the intent was
to test whether there were any entries in the used list.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All boards use EM28xxx_BOARD, to identify that the macro
refers to a card entry. So:
EM2874_LEADERSHIP_ISDBT -> EM2874_BOARD_LEADERSHIP_ISDBT
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some reason it repeats rather slowly, around 800ms intervals,
two RC5 remotes tested.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Basically it is just same device as Anysee E7 S2 but made for
internal PCI(e) slot and motherboard USB connector.
Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Basically it is just same device as Anysee E7 TC but made for
internal PCI(e) slot and motherboard USB connector.
Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sensor was found in a webcam 8020:ef04 (SVC - SVU2-1.3MV PCCam).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Align unfenced buffers on older hardware to the power-of-two object
size. The docs suggest that it should be possible to align only to a
power-of-two tile height, but using the already computed fence size is
easier and always correct. We also have to make sure that we unbind
misaligned buffers upon tiling changes.
In order to prevent a repetition of this bug, we change the interface
to the alignment computation routines to force the caller to provide
the requested alignment and size of the GTT binding rather than assume
the current values on the object.
Reported-and-tested-by: Sitosfe Wheeler <sitsofe@yahoo.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36326
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
pppoe: Must flush connections when MAC address changes too.
include/linux/sdla.h: remove the prototype of sdla()
tulip: dmfe: Remove old log spamming pr_debugs
Commit 726b65ad44 ("tulip: Convert uses of KERN_DEBUG") enabled
some old previously inactive uses of pr_debug converted by
commit dde7c8ef16 ("tulip/dmfe.c: Use dev_<level> and pr_<level>").
Remove these pr_debugs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While compiling it with Fedora 15, I noticed this issue:
inlined from ‘si4713_write_econtrol_string’ at drivers/media/radio/si4713-i2c.c:1065:24:
arch/x86/include/asm/uaccess_32.h:211:26: error: call to ‘copy_from_user_overflow’ declared with attribute error: copy_from_user() buffer size is not provably correct
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spi_sync call uses its spi_message parameter to keep completion information,
using a drvdata structure is not thread-safe. Use a mutex to prevent
multiple access to shared driver data.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Cyril Hrubis <metan@ucw.cz>
Tested-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
A copy-and-paste error caused it87_attributes_vid to be referenced
where it87_attributes_label should be. Thankfully the group is only
used for attribute removal, not attribute creation, so the effects of
this bug are limited, but let's fix it still.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The object returned by atk_gitm is dynamically allocated and must be
freed.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
hpwdt is a PCI driver so it should depend on PCI.
Fixes these build errors:
drivers/watchdog/hpwdt.c:762: error: implicit declaration of function 'pci_iomap'
drivers/watchdog/hpwdt.c:762: warning: assignment makes pointer from integer without a cast
drivers/watchdog/hpwdt.c:797: error: implicit declaration of function 'pci_iounmap'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Thomas Mingarelli <thomas.mingarelli@hp.com>
Remove Kconfig regression caused by commit
a4616153de "watchdog: hpwdt: build hpwdt as
module by default with NMI_DECODING enabled"
With the above change applied, hpwdt will be enabled unconditionally by just
entering the Watchdog subscreen in menuconfig. Since this driver is not
essential to boot any box it should remain disabled until it gets manually
enabled, just like all other drivers.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Only let the rx parser be enabled if it is necessary (if VLAN extraction,
IP or TCP checksumming or the rx queue filer are enabled). Otherwise
disable it.
The new routine gfar_check_rx_parser_mode should be run after every
change on this features and will enable/disable the parser as necessary.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (adm1275) Fix coefficients per datasheet revision B
hwmon: (pmbus) Use long variables for register to data conversions
When receiving the first RX interrupt before the internal call
to napi_schedule_prep is successful the RX interrupt gets disabled
and is never enabled again as the poll function never gets executed.
Signed-off-by: Michael Thalmeier <Michael.Thalmeier@sigmatek.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coefficients to convert chip register values to voltage/current have been
slightly changed in revision B of the chip datasheet. Update driver coefficients
to match the coefficients in the datasheet.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
There is no software fallback implemented for SCTP or FCoE checksumming,
and so it should not be passed on by software devices like bridge or bonding.
For VLAN devices, this is different. First, the driver for underlying device
should be prepared to get offloaded packets even when the feature is disabled
(especially if it advertises it in vlan_features). Second, devices under
VLANs do not get replaced without tearing down the VLAN first.
This fixes a mess I accidentally introduced while converting bonding to
ndo_fix_features.
NETIF_F_SOFT_FEATURES are removed from BOND_VLAN_FEATURES because they
are unused as of commit 712ae51afd.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've tried several times to make this machine 'just work', but every
patch that does causes many other machines to fail. This adds a quirk
which special cases this hardware and forces ssc to be
disabled. There's no way to override this from the command line; that
would be a significantly more invasive change.
This patch fixes#36656 on fdo bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=36656
Signed-off-by: Keith Packard <keithp@keithp.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36656
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The firmware on some machine will report duplicated hardware error
source ID in HEST. This is considered a firmware bug. To provide
better warning message, this patch adds duplicated hardware error
source ID detecting and corresponding printk.
This patch fixes#37412 on kernel bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=37412
Reported-by: marconifabio@ubuntu-it.org
Signed-off-by: Huang Ying <ying.huang@intel.com>
Tested-by: Mathias <janedo.spam@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As Simon reported, digital TV broke with mt20xx tuner due to
commit ad020dc2fe.
The mt20xx tuner passes V4L2_TUNER_DIGITAL_TV to tuner core. However, the
check_mode code now doesn't handle it well. Change the logic there to
avoid the breakage, and fix a test for analog-only at g_tuner.
Reported-by: Simon Arlott <simon@fire.lp0.eu>
Tested-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Attached is a patch which addresses a race condition in the DVB core
related to closing/reopening the DVB frontend device in quick
succession. This is the reason that devices such as the HVR-1300,
HVR-3000, and HVR-4000 have been failing to scan properly under MythTV
and w_scan.
The gory details of the race are described in the patch.
Devin
There is a race condition exhibited when channel scanners such as w_scan and
MythTV quickly close and then reopen the frontend device node.
Under normal conditions, the behavior is as follows:
1. Application closes the device node
2. DVB frontend ioctl calls dvb_frontend_release which sets
fepriv->release_jiffies
3. DVB frontend thread *eventually* calls dvb_frontend_is_exiting() which
compares fepriv->release_jiffies, and shuts down the thread if timeout has
expired
4. Thread goes away
5. Application opens frontend device
6. DVB frontend ioctl() calls ts_bus_ctrl(1)
7. DVB frontend ioctl() creates new frontend thread, which calls
dvb_frontend_init(), which has demod driver init() routine setup initial
register state for demod chip.
8. Tuning request is issued.
The race occurs when the application in step 5 performs the new open() call
before the frontend thread is shutdown. In this case the ts_bus_ctrl() call
is made, which strobes the RESET pin on the demodulator, but the
dvb_frontend_init() function never gets called because the frontend thread
hasn't gone away yet. As a result, the initial register config for the demod
is *never* setup, causing subsequent tuning requests to fail.
If there is time between the close and open (enough for the dvb frontend
thread to be torn down), then in that case the new frontend thread is created
and thus the dvb_frontend_init() function does get called.
The fix is to set the flag which forces reinitialization if we did in fact
call ts_bus_ctrl().
This problem has been seen on the HVR-1300, HVR-3000, and HVR-4000, and is
likely occuring on other designs as well where ts_bus_ctrl() actually strobes
the reset pin on the demodulator.
Note that this patch should supercede any patches submitted for the
1300/3000/4000 which remove the code that removes GPIO code in
cx8802_dvb_advise_acquire(), which have been circulating by users for some
time now...
Canonical tracking this issue in Launchpad 439163:
Thanks to Jon Sayers from Hauppauge and Florent Audebert from Anevia S.A. for
providing hardware to test/debug with.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jon Sayers <j.sayers@hauppauge.co.uk>
Cc: Florent Audebert <florent.audebert@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When CONFIG_SND is not enabled, radio-sf16fmr2 build fails with:
so make this driver depend on SND.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/evergreen: emit SQ_LDS_RESOURCE_MGMT for blits
agp/intel: Fix typo in G4x_GMCH_SIZE_VT_2M
drm/radeon/kms: fix typo in read_disabled vbios code
drm/radeon/kms: use correct BUS_CNTL reg on rs600
drm/radeon/kms: fix backend map typo on juniper
drm/radeon/kms: fix regression in hotplug
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
slip: fix wrong SLIP6 ifdef-endif placing
natsemi: fix another dma-debug report
sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
net: Fix default in docs for tcp_orphan_retries.
hso: fix a use after free condition
net/natsemi: Fix module parameter permissions
XFRM: Fix memory leak in xfrm_state_update
sctp: Enforce retransmission limit during shutdown
mac80211: fix TKIP replay vulnerability
mac80211: fix ie memory allocation for scheduled scans
ssb: fix init regression of hostmode PCI core
rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
carl9170: add NEC WL300NU-AG usbid
cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
ath5k: fix incorrect use of drvdata in PCI suspend/resume code
ath5k: fix incorrect use of drvdata in sysfs code
Bluetooth: Fix memory leak under page timeouts
Bluetooth: Fix regression with incoming L2CAP connections
Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
...
On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.
On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.
This fixes a regression introduced in 3.0-rc1 by 08ee80cc39
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All ACPICA locks are allocated by the same function,
acpi_os_create_lock(), with the help of a local variable called
"lock". Thus, when lockdep is enabled, it uses "lock" as the
name of all those locks and regards them as instances of the same
lock, which causes it to report possible locking problems with them
when there aren't any.
To work around this problem, define acpi_os_create_lock() as a macro
and make it pass its argument to spin_lock_init(), so that lockdep
uses it as the name of the new lock. Define this macron in a
Linux-specific file, to minimize the resulting modifications of
the OS-independent ACPICA parts.
This change is based on an earlier patch from Andrea Righi and it
addresses a regression from 2.6.39 tracked as
https://bugzilla.kernel.org/show_bug.cgi?id=38152
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Tested-by: Andrea Righi <andrea@betterlinux.com>
Reviewed-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Compute drivers may change this, so make sure to emit it to
avoid errors in bo blits.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=39119
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Konstantin Belousov found an error in the define of G4x_GMCH_SIZE_VT_2M
relative to the GMCH specs, and confirmed that indeed one of his users
with a Q45 reports 0xb not 0xc for a 2/2MiB GATT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Konstantin Belousov <kostikbel@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
sound/isa/es18xx.c: In function ‘snd_es18xx_playback1_prepare’:
sound/isa/es18xx.c:501:9: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/es18xx.c: In function ‘snd_es18xx_playback_pointer’:
sound/isa/es18xx.c:818:3: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [sound/isa/es18xx.o] Error 1
sound/isa/sscape.c: In function ‘upload_dma_data’:
sound/isa/sscape.c:481:3: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [sound/isa/sscape.o] Error 1
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_playback_prepare’:
sound/isa/ad1816a/ad1816a_lib.c:244:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_playback_pointer’:
sound/isa/ad1816a/ad1816a_lib.c:302:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_free’:
sound/isa/ad1816a/ad1816a_lib.c:544:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/ad1816a/ad1816a_lib.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/ad1816a] Error 2
sound/isa/es1688/es1688_lib.c: In function ‘snd_es1688_playback_prepare’:
sound/isa/es1688/es1688_lib.c:417:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/es1688/es1688_lib.c: In function ‘snd_es1688_playback_pointer’:
sound/isa/es1688/es1688_lib.c:509:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/es1688/es1688_lib.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/es1688] Error 2
sound/isa/gus/gus_dma.c: In function ‘snd_gf1_dma_program’:
sound/isa/gus/gus_dma.c:79:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/gus/gus_dma.c: In function ‘snd_gf1_dma_done’:
sound/isa/gus/gus_dma.c:177:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/gus/gus_dma.o] Error 1
sound/isa/gus/gus_pcm.c: In function ‘snd_gf1_pcm_capture_prepare’:
sound/isa/gus/gus_pcm.c:591:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/gus/gus_pcm.c: In function ‘snd_gf1_pcm_capture_pointer’:
sound/isa/gus/gus_pcm.c:619:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/gus/gus_pcm.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/gus] Error 2
sound/isa/sb/sb16_csp.c: In function ‘snd_sb_csp_ioctl’:
sound/isa/sb/sb16_csp.c:228:227: error: case label does not reduce to an integer constant
make[3]: *** [sound/isa/sb/sb16_csp.o] Error 1
sound/isa/sb/sb16_main.c: In function ‘snd_sb16_playback_prepare’:
sound/isa/sb/sb16_main.c:276:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/sb/sb16_main.c: In function ‘snd_sb16_playback_pointer’:
sound/isa/sb/sb16_main.c:456:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/sb/sb16_main.o] Error 1
sound/isa/sb/sb8_main.c: In function ‘snd_sb8_playback_prepare’:
sound/isa/sb/sb8_main.c:172:3: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/sb/sb8_main.c: In function ‘snd_sb8_playback_pointer’:
sound/isa/sb/sb8_main.c:425:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/sb/sb8_main.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/sb] Error 2
sound/isa/wss/wss_lib.c: In function ‘snd_wss_playback_prepare’:
sound/isa/wss/wss_lib.c:1025:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/wss/wss_lib.c: In function ‘snd_wss_playback_pointer’:
sound/isa/wss/wss_lib.c:1160:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
sound/isa/wss/wss_lib.c: In function ‘snd_wss_free’:
sound/isa/wss/wss_lib.c:1695:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/wss/wss_lib.o] Error 1
warning: (RADIO_MIROPCM20) selects SND_ISA which has unmet direct dependencies (SOUND && !M68K && SND && ISA && ISA_DMA_API)
A build with ISA && ISA_DMA && !ISA_DMA_API results in:
CC sound/isa/es18xx.o
CC sound/isa/sscape.o
CC sound/isa/ad1816a/ad1816a_lib.o
CC sound/isa/es1688/es1688_lib.o
CC sound/isa/gus/gus_dma.o
CC sound/isa/gus/gus_pcm.o
CC sound/isa/sb/sb16_csp.o
CC sound/isa/sb/sb16_main.o
CC sound/isa/sb/sb8_main.o
CC sound/isa/wss/wss_lib.o
The root cause for this is hidden in this Kconfig warning:
Adding a dependency on ISA_DMA_API to RADIO_MIROPCM20 fixes these issues.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix memory_block_size_bytes() for non-pseries
mm: Move definition of MIN_MEMORY_BLOCK_SIZE to a header
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
Revert "drm/i915: enable rc6 by default"
drm/i915: Clean up i915_driver_load failure path
drm/i915: Enable GPU reset on Ivybridge.
drm/i915/dp: manage sink power state if possible
drm/i915/dp: consolidate AUX retry code
drm/i915/dp: remove DPMS mode tracking from DP
drm/i915/dp: try to read receiver capabilities 3 times when detecting
drm/i915/dp: read more receiver capability bits on hotplug
drm/i915/dp: use DP DPCD defines when looking at DPCD values
drm/i915/dp: retry link status read 3 times on failure
...which is measured by the size and not the amount of space remaining.
Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:
[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
This reverts commit a51f7a66fb.
We still have a few Ironlake and Sandybridge machines which fail when
RC6 is enabled. Better luck next release?
Signed-off-by: Keith Packard <keithp@keithp.com>
i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.
i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.
i915_driver_load also has some incorrect gotos in the error cleanup
paths:
* After failing to initialize the GTT (which cannot happen, btw,
intel_gtt_get returns a fixed (non-NULL) value), it tries to
free the uninitialized WC IO mapping. Fixed this by changing the
target from out_iomapfree to out_rmmap
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Lin Ming <ming.m.lin@intel.com>
Using integer variable types for register to data conversions can cause
overflows especially for power calculations, which are in microwatt.
Use long variables instead.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+
BUS_CNTL reg and bits moved between pre-PCIE and PCIE asics.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Skip connectors that do not have an HPD pin.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=39027
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
SLIP6 have nothing to do with CSLIP so placing a block of
SLIP6-related code within a CSLIP ifdef-endif block is incorrect.
Signed-off-by: Ilya Matvejchikov <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro MIN_MEMORY_BLOCK_SIZE is currently defined twice in two .c
files, and I need it in a third one to fix a powerpc bug, so let's
first move it into a header
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
The nuvoton-cir inherited an insanely low idle timeout value from the
mceusb driver. We're fixing mceusb, should fix this driver too.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This matches the typical timeout advertised by hardware, once we're
actually interpreting it correctly.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unit missmatch in mceusb_handle_command. It should be converting to us,
not 1/10th of ms.
mceusb_dev_printdata 100us/ms -> 1000us/ms
Alter format of fix slightly and update comment to match proper reality.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit e38030f3ff.
MSI flat-out doesn't work right on cx2388x devices yet. There are now
multiple reports of cards that hard-lock systems when MSI is enabled,
including my own HVR-1250 when trying to use its built-in IR receiver.
Disable MSI and it works just fine. Similar for another user's HVR-1270.
Issues have also been reported with the HVR-1850 when MSI is enabled,
and the 1850 behavior sounds similar to an as-yet-undiagnosed issue I've
seen with an 1800.
CC: stable@kernel.org
CC: Steven Toth <stoth@kernellabs.com>
CC: Kusanagi Kouichi <slash@ac.auone-net.jp>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] msp3400: fill in v4l2_tuner based on vt->type field
[media] tuner-core.c: don't change type field in g_tuner or g_frequency
[media] cx18/ivtv: fix g_tuner support
[media] tuner-core: power up tuner when called with s_power(1)
[media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
[media] tuner-core: simplify the standard fixup
[media] tuner-core/v4l2-subdev: document that the type field has to be filled in
[media] v4l2-subdev.h: remove unused s_mode tuner op
[media] feature-removal-schedule: change in how radio device nodes are handled
[media] bttv: fix s_tuner for radio
[media] pvrusb2: fix g/s_tuner support
[media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
[media] tuner-core: fix tuner_resume: use t->mode instead of t->type
[media] tuner-core: fix s_std and s_tuner
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
hp-wmi: fix use after free
dell-laptop - using buffer without mutex_lock
Revert: "dell-laptop: Toggle the unsupported hardware killswitch"
platform-drivers-x86: set backlight type to BACKLIGHT_PLATFORM
thinkpad-acpi: handle HKEY 0x4010, 0x4011 events
drivers/platform/x86: Fix memory leak
thinkpad-acpi: handle some new HKEY 0x60xx events
acer-wmi: fix bitwise bug when set device state
acer-wmi: Only update rfkill status for associated hotkey events
[ 191.310008] WARNING: kmemcheck: Caught 32-bit read from freed memory (f0d25f14)
[ 191.310011] c056d2f088000000105fd2f00000000050415353040000000000000000000000
[ 191.310020] i i i i f f f f f f f f f f f f f f f f f f f f f f f f f f f f
[ 191.310027] ^
[ 191.310029]
[ 191.310032] Pid: 737, comm: modprobe Not tainted 3.0.0-rc5+ #268 Hewlett-Packard HP Compaq 6005 Pro SFF PC/3047h
[ 191.310036] EIP: 0060:[<f80b3104>] EFLAGS: 00010286 CPU: 0
[ 191.310039] EIP is at hp_wmi_perform_query+0x104/0x150 [hp_wmi]
[ 191.310041] EAX: f0d25601 EBX: f0d25f00 ECX: 000121cf EDX: 000121ce
[ 191.310043] ESI: f0d25f10 EDI: f0f97ea8 EBP: f0f97ec4 ESP: c173f34c
[ 191.310045] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 191.310046] CR0: 8005003b CR2: f540c000 CR3: 30f30000 CR4: 000006d0
[ 191.310048] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 191.310050] DR6: ffff4ff0 DR7: 00000400
[ 191.310051] [<f80b317b>] hp_wmi_dock_state+0x2b/0x40 [hp_wmi]
[ 191.310054] [<f80b6093>] hp_wmi_init+0x93/0x1a8 [hp_wmi]
[ 191.310057] [<c10011f0>] do_one_initcall+0x30/0x170
[ 191.310061] [<c107ab9f>] sys_init_module+0xef/0x1a60
[ 191.310064] [<c149f998>] sysenter_do_call+0x12/0x28
[ 191.310067] [<ffffffff>] 0xffffffff
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This reverts commit a3d77411e8,
as it causes a mess in the wireless rfkill status on some models.
It is probably a bad idea to toggle the rfkill for all dell models
without the respect to the claim that it is hardware-controlled.
Cc: stable@kernel.org
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Patch 2e711c04db
(PM: Remove sysdev suspend, resume and shutdown operations)
deleted sysdev_suspend(), which was being relied on to call
check_wakeup_irqs() in suspend. If check_wakeup_irqs() is not
called, wake interrupts that are pending when suspend is
entered may be lost. It also breaks IRQCHIP_MASK_ON_SUSPEND,
which is handled in check_wakeup_irqs().
This patch adds a call to check_wakeup_irqs() in syscore_suspend(),
similar to what was deleted in sysdev_suspend().
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
I came across a memory leak during a cyclic cpu-online-offline test.
Signed-off-by: Yu Luming <luming.yu@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (pmbus) Improve auto-detection of temperature status register
hwmon: (lm95241) Fix negative temperature results
hwmon: (lm95241) Fix chip detection code
It is possible that a PMBus device supports the READ_TEMPERATURE2 and/or
READ_TEMPERATURE3 registers but does not support READ_TEMPERATURE1.
Improve temperature status register detection to address this condition.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+
Negative temperatures were returned in degrees C instead of milli-Degrees C.
Also, negative temperatures were reported for remote temperature sensors even
if the chip was configured for positive-only results.
Fix by detecting temperature modes, and by treating negative temperatures
similar to positive temperatures, with appropriate sign extension.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+
David Härdeman