The device is configured to insert hardware timestamps into all
received packets. The RX timestamps are extracted from the padding
alingment bytes during the clean_rx_ring operation and copied into the
skb_shared_hwtstamps struct of the skb. This extraction only happens if
the rx_filter was set to something else than HWTSTAMP_FILTER_NONE with
the SIOCSHWTSTAMP ioctl command.
Hardware timestamping is only supported for eTSEC devices. To indicate
device support the new FSL_GIANFAR_DEV_HAS_TIMER flag was introduced.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for using the LL TEMAC Ethernet driver on
non-Virtex 5 platforms by adding support for accessing the Soft DMA
registers as if they were memory mapped instead of solely through the
DCR's (available on the Virtex 5).
The patch also updates the driver so that it runs on the MicroBlaze.
The changes were tested on the PowerPC 440, PowerPC 405, and the
MicroBlaze platforms.
Signed-off-by: John Tyner <jtyner@cs.ucr.edu>
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The virt_to_bus call should not be used any longer as it's
considered illegal. The driver has the physical address of
the buffer in the descriptor such that it's not necessary
anyway.
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for SJA1000 based PCI CAN interface cards
from electronic system design gmbh.
Some changes have been done on the common code:
- esd boards must not have the 2nd local interupt enabled (PLX9030/9050)
- a new path for PLX9056/PEX8311 chips has been added
- new plx9056 reset function has been implemented
- struct plx_card_info got a reset function entry
In detail the following additional boards are now supported:
CAN-PCI/200 (PCI)
CAN-PCI/266 (PCI)
CAN-PMC266 (PMC module)
CAN-PCIe/2000 (PCI Express)
CAN-CPCI/200 (Compact PCI, 3U)
CAN-PCI104 (PCI104)
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- max_config_dev loadable parameter is set to 0xFF by default. Pass correct
number of VFs value to pci_sriov_enable() if max_config_dev is set to its
default value.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Allow all instances of the driver be loaded when multiple pci functions are
enumerated. The max_config_dev driver loadable option limits the driver
load instances if required. The X3100's function configuration of single/multi
function, SR and MR IOV allows the user to select the number of pci functions.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix a possible memory leak in vxge_hw_device_initialize(). Free hldev if
vxge_hw_device_reg_addr_get() fails.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix rx_pause management in myri10ge_set_pauseparam().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable BIG bit in the network configuration register, so the MAC
doesn't reject big frames (E.G. when vlans are used).
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resource size should be calculated as end - start + 1 because we start
counting at zero. I changed the code to resource_size() to do the
calculation.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API is preferred.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Vladislav Zolotarov <vladz@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move sg structure off stack and into virtnet_info structure.
This helps remove extra sg_init_table calls as well as reduce
stack usage.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
benet driver wrongly assumes that zero is an invalid dma address
(calls dma_unmap_page for only non zero dma addresses). Zero is a
valid dma address on some architectures. The dma length can be used
here.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API is preferred.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver attempts to select an IRQ for the NIC automatically by
testing which of the supported IRQs are available and then probing
each available IRQ with probe_irq_{on,off}(). There are obvious race
conditions here, besides which:
1. The test for availability is done by passing a NULL handler, which
now always returns -EINVAL, thus the device cannot be opened:
<http://bugs.debian.org/566522>
2. probe_irq_off() will report only the first ISA IRQ handled,
potentially leading to a false negative.
There was another bug that meant it ignored all error codes from
request_irq() except -EBUSY, so it would 'succeed' despite this
(possibly causing conflicts with other ISA devices). This was fixed
by ab08999d60 'WARNING: some
request_irq() failures ignored in el2_open()', which exposed bug 1.
This patch:
1. Replaces the use of probe_irq_{on,off}() with a real interrupt handler
2. Adds a delay before checking the interrupt-seen flag
3. Disables interrupts on all failure paths
4. Distinguishes error codes from the second request_irq() call,
consistently with the first
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
cnic_service_bnx2x() irq handler can be called during chip reset from
MTU change. Need to check that the cnic's device state is up before
handling the irq.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If interface is down, mac address request are not sent to fw
but it is getting add in driver mac list.
Driver mac list should be in sync with fw i.e addresses communicated
to fw.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported in <https://bugzilla.kernel.org/show_bug.cgi?id=15355>, r6040_
multicast_list currently crashes. This is due a wrong maximum of multicast
entries. This patch fixes the following issues with multicast:
- number of maximum entries if off-by-one (4 instead of 3)
- the writing of the hash table index is not necessary and leads to invalid
values being written into the MCR1 register, so the MAC is simply put in a non
coherent state
- when we exceed the maximum number of mutlticast address, writing the
broadcast address should be done in registers MID_1{L,M,H} instead of
MID_O{L,M,H}, otherwise we would loose the adapter's MAC address
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't think this can be abused in this case but do things properly.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
write is optional for a tty device. Check that we have a write op rather
than calling NULL.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
{set,get}_msglevel is required to use netif_{err,dbg} macros.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes multiple errors reported by checkpatch:
- else not on the ending brace of an if { }
- multiple occurences of for( instead of for (
- c99 comments
- assignment and tests on the same line
- test and statements on the same line
- macro with complex value not between parenthesis
- static variable with initialization value
No functionnal change.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid namespace clashes, prefix all internal driver functions
with au1000_.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the au1000-eth driver to be compiled as a module.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds setting of the urb transfer flag URB_ZERO_PACKET before
submitting an urb for drivers that have requested it (by advertising flag
FLAG_SEND_ZLP).
The modification is in usbnet.c function usbnet_start_xmit().
This patch only adds the zero length flag.
A subsequent patch will address the buggy code we found when devices do not
advertise FLAG_SEND_ZLP in which case there is a possibility of transferring
packets with non-deterministic length.
This patch has been tested on kernel-2.6.34-rc3.
This patch has been checked against net-2.6 tree.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Rory Filer <rfiler@sierrawireless.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is very simple driver for SuperH Mobile IrDA
which support SIR/MIR/FIR.
This patch add only SIR support for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sh_sir_probe function, there was a possibility that
iounmap is executed even though self->membase was NULL when error case.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sh_sir_open function, there was a possibility that
err variable didn't have value even though it is return value.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for using the LL TEMAC Ethernet driver on
non-Virtex 5 platforms by adding support for accessing the Soft DMA
registers as if they were memory mapped instead of solely through the
DCR's (available on the Virtex 5).
The patch also updates the driver so that it runs on the MicroBlaze.
The changes were tested on the PowerPC 440, PowerPC 405, and the
MicroBlaze platforms.
Signed-off-by: John Tyner <jtyner@cs.ucr.edu>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registers and their bits from mii.h. Courtesy from ed.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
smc91c92_cs: fix the problem of "Unable to find hardware address"
r8169: clean up my printk uglyness
net: Hook up cxgb4 to Kconfig and Makefile
cxgb4: Add main driver file and driver Makefile
cxgb4: Add remaining driver headers and L2T management
cxgb4: Add packet queues and packet DMA code
cxgb4: Add HW and FW support code
cxgb4: Add register, message, and FW definitions
netlabel: Fix several rcu_dereference() calls used without RCU read locks
bonding: fix potential deadlock in bond_uninit()
net: check the length of the socket address passed to connect(2)
stmmac: add documentation for the driver.
stmmac: fix kconfig for crc32 build error
be2net: fix bug in vlan rx path for big endian architecture
be2net: fix flashing on big endian architectures
be2net: fix a bug in flashing the redboot section
bonding: bond_xmit_roundrobin() fix
drivers/net: Add missing unlock
net: gianfar - align BD ring size console messages
net: gianfar - initialize per-queue statistics
...
This patch updates the tg3 version to 3.109.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_dump_state() function is commented out and doesn't get used much
when debugging efforts are underway. The chip architecture has also
changed enough that any debugging effort that might use it would have to
tailor it to the capabilities of the hardware. This patch just removes
the function entirely.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the code style as it pertains to if statements.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes checkpatch errors related to switch statements.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manfred Rudigier