IP_MULTICAST_IF fails if sk_bound_dev_if is already set and the new index
does not match it. e.g.,
ntpd[15381]: setsockopt IP_MULTICAST_IF 192.168.1.23 fails: Invalid argument
Relax the check in setsockopt to allow setting mc_index to an L3 slave if
sk_bound_dev_if points to an L3 master.
Make a similar change for IPv6. In this case change the device lookup to
take the rcu_read_lock avoiding a refcnt. The rcu lock is also needed for
the lookup of a potential L3 master device.
This really only silences a setsockopt failure since uses of mc_index are
secondary to sk_bound_dev_if if it is set. In both cases, if either index
is an L3 slave or master, lookups are directed to the same FIB table so
relaxing the check at setsockopt time causes no harm.
Patch is based on a suggested change by Darwin for a problem noted in
their code base.
Suggested-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require different maximal
number of remembered connection requests.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require fast recycling
TIME-WAIT sockets independently of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Socket cmsg IP(V6)_RECVORIGDSTADDR checks that port range lies within
the packet. For sockets that have transport headers pulled, transport
offset can be negative. Use signed comparison to avoid overflow.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Reported-by: Nisar Jagabar <njagabar@cloudmark.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e2d118a1cb ("net: inet: Support UID-based routing in IP
protocols.") made ip_do_redirect call sock_net(sk) to determine
the network namespace of the passed-in socket. This crashes if sk
is NULL.
Fix this by getting the network namespace from the skb instead.
Fixes: e2d118a1cb ("net: inet: Support UID-based routing in IP protocols.")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin reported crashes happening in tcp_tasklet_func() on powerpc64
Before TSQ_QUEUED bit is cleared, we must ensure the changes done
by list_del(&tp->tsq_node); are committed to memory, otherwise
corruption might happen, as an other cpu could catch TSQ_QUEUED
clearance too soon.
We can notice that old kernels were immune to this bug, because
TSQ_QUEUED was cleared after a bh_lock_sock(sk)/bh_unlock_sock(sk)
section, but they could have missed a kick to write additional bytes,
when NIC interrupts for a given flow are spread to multiple cpus.
Affected TCP flows would need an incoming ACK or RTO timer to add more
packets to the pipe. So overall situation should be better now.
Fixes: b223feb9de ("tcp: tsq: add shortcut in tcp_tasklet_func()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Madalin Bucur <madalin.bucur@nxp.com>
Tested-by: Madalin Bucur <madalin.bucur@nxp.com>
Tested-by: Xing Lei <xing.lei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an inconsistent conditional judgement in __ip_append_data and
ip_finish_output functions, the variable length in __ip_append_data just
include the length of application's payload and udp header, don't include
the length of ip header, but in ip_finish_output use
(skb->len > ip_skb_dst_mtu(skb)) as judgement, and skb->len include the
length of ip header.
That causes some particular application's udp payload whose length is
between (MTU - IP Header) and MTU were fragmented by ip_fragment even
though the rst->dev support UFO feature.
Add the length of ip header to length in __ip_append_data to keep
consistent conditional judgement as ip_finish_output for ip fragment.
Signed-off-by: Zheng Li <james.z.li@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
A user may call listen with binding an explicit port with the intent
that the kernel will assign an available port to the socket. In this
case inet_csk_get_port does a port scan. For such sockets, the user may
also set soreuseport with the intent a creating more sockets for the
port that is selected. The problem is that the initial socket being
opened could inadvertently choose an existing and unreleated port
number that was already created with soreuseport.
This patch adds a boolean parameter to inet_bind_conflict that indicates
rather soreuseport is allowed for the check (in addition to
sk->sk_reuseport). In calls to inet_bind_conflict from inet_csk_get_port
the argument is set to true if an explicit port is being looked up (snum
argument is nonzero), and is false if port scan is done.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_csk_get_port is called with port number (snum argument) that may be
zero or nonzero. If it is zero, then the intent is to find an available
ephemeral port number to bind to. If snum is non-zero then the caller
is asking to allocate a specific port number. In the latter case we
never want to perform the scan in ephemeral port range. It is
conceivable that this can happen if the "goto again" in "tb_found:"
is done. This patch adds a check that snum is zero before doing
the "goto again".
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs updates from Al Viro:
- more ->d_init() stuff (work.dcache)
- pathname resolution cleanups (work.namei)
- a few missing iov_iter primitives - copy_from_iter_full() and
friends. Either copy the full requested amount, advance the iterator
and return true, or fail, return false and do _not_ advance the
iterator. Quite a few open-coded callers converted (and became more
readable and harder to fuck up that way) (work.iov_iter)
- several assorted patches, the big one being logfs removal
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
logfs: remove from tree
vfs: fix put_compat_statfs64() does not handle errors
namei: fold should_follow_link() with the step into not-followed link
namei: pass both WALK_GET and WALK_MORE to should_follow_link()
namei: invert WALK_PUT logics
namei: shift interpretation of LOOKUP_FOLLOW inside should_follow_link()
namei: saner calling conventions for mountpoint_last()
namei.c: get rid of user_path_parent()
switch getfrag callbacks to ..._full() primitives
make skb_add_data,{_nocache}() and skb_copy_to_page_nocache() advance only on success
[iov_iter] new primitives - copy_from_iter_full() and friends
don't open-code file_inode()
ceph: switch to use of ->d_init()
ceph: unify dentry_operations instances
lustre: switch to use of ->d_init()
In flood situations, keeping sk_rmem_alloc at a high value
prevents producers from touching the socket.
It makes sense to lower sk_rmem_alloc only at the end
of udp_rmem_release() after the thread draining receive
queue in udp_recvmsg() finished the writes to sk_forward_alloc.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If udp_recvmsg() constantly releases sk_rmem_alloc
for every read packet, it gives opportunity for
producers to immediately grab spinlocks and desperatly
try adding another packet, causing false sharing.
We can add a simple heuristic to give the signal
by batches of ~25 % of the queue capacity.
This patch considerably increases performance under
flood by about 50 %, since the thread draining the queue
is no longer slowed by false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In UDP RX handler, we currently clear skb->dev before skb
is added to receive queue, because device pointer is no longer
available once we exit from RCU section.
Since this first cache line is always hot, lets reuse this space
to store skb->truesize and thus avoid a cache line miss at
udp_recvmsg()/udp_skb_destructor time while receive queue
spinlock is held.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Idea of busylocks is to let producers grab an extra spinlock
to relieve pressure on the receive_queue spinlock shared by consumer.
This behavior is requested only once socket receive queue is above
half occupancy.
Under flood, this means that only one producer can be in line
trying to acquire the receive_queue spinlock.
These busylock can be allocated on a per cpu manner, instead of a
per socket one (that would consume a cache line per socket)
This patch considerably improves UDP behavior under stress,
depending on number of NIC RX queues and/or RPS spread.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under UDP flood, many softirq producers try to add packets to
UDP receive queue, and one user thread is burning one cpu trying
to dequeue packets as fast as possible.
Two parts of the per packet cost are :
- copying payload from kernel space to user space,
- freeing memory pieces associated with skb.
If socket is under pressure, softirq handler(s) can try to pull in
skb->head the payload of the packet if it fits.
Meaning the softirq handler(s) can free/reuse the page fragment
immediately, instead of letting udp_recvmsg() do this hundreds of usec
later, possibly from another node.
Additional gains :
- We reduce skb->truesize and thus can store more packets per SO_RCVBUF
- We avoid cache line misses at copyout() time and consume_skb() time,
and avoid one put_page() with potential alien freeing on NUMA hosts.
This comes at the cost of a copy, bounded to available tail room, which
is usually small. (We might have to fix GRO_MAX_HEAD which looks bigger
than necessary)
This patch gave me about 5 % increase in throughput in my tests.
skb_condense() helper could probably used in other contexts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, icmp_rcv() always return zero on a packet delivery upcall.
To make its behavior more compliant with the way this API should be
used, this patch changes this to let it return NET_RX_SUCCESS when the
packet is proper handled, and NET_RX_DROP otherwise.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains a large Netfilter update for net-next,
to summarise:
1) Add support for stateful objects. This series provides a nf_tables
native alternative to the extended accounting infrastructure for
nf_tables. Two initial stateful objects are supported: counters and
quotas. Objects are identified by a user-defined name, you can fetch
and reset them anytime. You can also use a maps to allow fast lookups
using any arbitrary key combination. More info at:
http://marc.info/?l=netfilter-devel&m=148029128323837&w=2
2) On-demand registration of nf_conntrack and defrag hooks per netns.
Register nf_conntrack hooks if we have a stateful ruleset, ie.
state-based filtering or NAT. The new nf_conntrack_default_on sysctl
enables this from newly created netnamespaces. Default behaviour is not
modified. Patches from Florian Westphal.
3) Allocate 4k chunks and then use these for x_tables counter allocation
requests, this improves ruleset load time and also datapath ruleset
evaluation, patches from Florian Westphal.
4) Add support for ebpf to the existing x_tables bpf extension.
From Willem de Bruijn.
5) Update layer 4 checksum if any of the pseudoheader fields is updated.
This provides a limited form of 1:1 stateless NAT that make sense in
specific scenario, eg. load balancing.
6) Add support to flush sets in nf_tables. This series comes with a new
set->ops->deactivate_one() indirection given that we have to walk
over the list of set elements, then deactivate them one by one.
The existing set->ops->deactivate() performs an element lookup that
we don't need.
7) Two patches to avoid cloning packets, thus speed up packet forwarding
via nft_fwd from ingress. From Florian Westphal.
8) Two IPVS patches via Simon Horman: Decrement ttl in all modes to
prevent infinite loops, patch from Dwip Banerjee. And one minor
refactoring from Gao feng.
9) Revisit recent log support for nf_tables netdev families: One patch
to ensure that we correctly handle non-ethernet packets. Another
patch to add missing logger definition for netdev. Patches from
Liping Zhang.
10) Three patches for nft_fib, one to address insufficient register
initialization and another to solve incorrect (although harmless)
byteswap operation. Moreover update xt_rpfilter and nft_fib to match
lbcast packets with zeronet as source, eg. DHCP Discover packets
(0.0.0.0 -> 255.255.255.255). Also from Liping Zhang.
11) Built-in DCCP, SCTP and UDPlite conntrack and NAT support, from
Davide Caratti. While DCCP is rather hopeless lately, and UDPlite has
been broken in many-cast mode for some little time, let's give them a
chance by placing them at the same level as other existing protocols.
Thus, users don't explicitly have to modprobe support for this and
NAT rules work for them. Some people point to the lack of support in
SOHO Linux-based routers that make deployment of new protocols harder.
I guess other middleboxes outthere on the Internet are also to blame.
Anyway, let's see if this has any impact in the midrun.
12) Skip software SCTP software checksum calculation if the NIC comes
with SCTP checksum offload support. From Davide Caratti.
13) Initial core factoring to prepare conversion to hook array. Three
patches from Aaron Conole.
14) Gao Feng made a wrong conversion to switch in the xt_multiport
extension in a patch coming in the previous batch. Fix it in this
batch.
15) Get vmalloc call in sync with kmalloc flags to avoid a warning
and likely OOM killer intervention from x_tables. From Marcelo
Ricardo Leitner.
16) Update Arturo Borrero's email address in all source code headers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, if fib lookup fail, *dest will be filled with garbage value,
so reverse path filtering will not work properly:
# nft add rule x prerouting fib saddr oif eq 0 drop
Fixes: f6d0cbcf09 ("netfilter: nf_tables: add fib expression")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acctually ntohl and htonl are identical, so this doesn't affect
anything, but it is conceptually wrong.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
instead of allocating each xt_counter individually, allocate 4k chunks
and then use these for counter allocation requests.
This should speed up rule evaluation by increasing data locality,
also speeds up ruleset loading because we reduce calls to the percpu
allocator.
As Eric points out we can't use PAGE_SIZE, page_allocator would fail on
arches with 64k page size.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Keeps some noise away from a followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On SMP we overload the packet counter (unsigned long) to contain
percpu offset. Hide this from callers and pass xt_counters address
instead.
Preparation patch to allocate the percpu counters in page-sized batch
chunks.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_defrag modules for ipv4 and ipv6 export an empty stub function.
Any module that needs the defragmentation hooks registered simply 'calls'
this empty function to create a phony module dependency -- modprobe will
then load the defrag module too.
This extends netfilter ipv4/ipv6 defragmentation modules to delay the hook
registration until the functionality is requested within a network namespace
instead of module load time for all namespaces.
Hooks are only un-registered on module unload or when a namespace that used
such defrag functionality exits.
We have to use struct net for this as the register hooks can be called
before netns initialization here from the ipv4/ipv6 conntrack module
init path.
There is no unregister functionality support, defrag will always be
active once it was requested inside a net namespace.
The reason is that defrag has impact on nft and iptables rulesets
(without defrag we might see framents).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Neal Cardwell says:
If I am reading the code correctly, then I would have two concerns:
1) Has that been tested? That seems like an extremely dramatic
decrease in cwnd. For example, if the cwnd is 80, and there are 40
ACKs, and half the ACKs are ECE marked, then my back-of-the-envelope
calculations seem to suggest that after just 11 ACKs the cwnd would be
down to a minimal value of 2 [..]
2) That seems to contradict another passage in the draft [..] where it
sazs:
Just as specified in [RFC3168], DCTCP does not react to congestion
indications more than once for every window of data.
Neal is right. Fortunately we don't have to complicate this by testing
vs. current rtt estimate, we can just revert the patch.
Normal stack already handles this for us: receiving ACKs with ECE
set causes a call to tcp_enter_cwr(), from there on the ssthresh gets
adjusted and prr will take care of cwnd adjustment.
Fixes: 4780566784 ("dctcp: update cwnd on congestion event")
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been some reports lately about TCP connection stalls caused
by NIC drivers that aren't setting gso_size on aggregated packets on rx
path. This causes TCP to assume that the MSS is actually the size of the
aggregated packet, which is invalid.
Although the proper fix is to be done at each driver, it's often hard
and cumbersome for one to debug, come to such root cause and report/fix
it.
This patch amends this situation in two ways. First, it adds a warning
on when this situation occurs, so it gives a hint to those trying to
debug this. It also limit the maximum probed MSS to the adverised MSS,
as it should never be any higher than that.
The result is that the connection may not have the best performance ever
but it shouldn't stall, and the admin will have a hint on what to look
for.
Tested with virtio by forcing gso_size to 0.
v2: updated msg per David's suggestion
v3: use skb_iif to find the interface and also log its name, per Eric
Dumazet's suggestion. As the skb may be backlogged and the interface
gone by then, we need to check if the number still has a meaning.
v4: use helper tcp_gro_dev_warn() and avoid pr_warn_once inside __once, per
David's suggestion
Cc: Jonathan Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to commit c0371da604 ("put iov_iter into msghdr") in v3.19, there
was no check that the iovec contained enough bytes for an ICMP header,
and the read loop would walk across neighboring stack contents. Since the
iov_iter conversion, bad arguments are noticed, but the returned error is
EFAULT. Returning EINVAL is a clearer error and also solves the problem
prior to v3.19.
This was found using trinity with KASAN on v3.18:
BUG: KASAN: stack-out-of-bounds in memcpy_fromiovec+0x60/0x114 at addr ffffffc071077da0
Read of size 8 by task trinity-c2/9623
page:ffffffbe034b9a08 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x0()
page dumped because: kasan: bad access detected
CPU: 0 PID: 9623 Comm: trinity-c2 Tainted: G BU 3.18.0-dirty #15
Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT)
Call trace:
[<ffffffc000209c98>] dump_backtrace+0x0/0x1ac arch/arm64/kernel/traps.c:90
[<ffffffc000209e54>] show_stack+0x10/0x1c arch/arm64/kernel/traps.c:171
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffc000f18dc4>] dump_stack+0x7c/0xd0 lib/dump_stack.c:50
[< inline >] print_address_description mm/kasan/report.c:147
[< inline >] kasan_report_error mm/kasan/report.c:236
[<ffffffc000373dcc>] kasan_report+0x380/0x4b8 mm/kasan/report.c:259
[< inline >] check_memory_region mm/kasan/kasan.c:264
[<ffffffc00037352c>] __asan_load8+0x20/0x70 mm/kasan/kasan.c:507
[<ffffffc0005b9624>] memcpy_fromiovec+0x5c/0x114 lib/iovec.c:15
[< inline >] memcpy_from_msg include/linux/skbuff.h:2667
[<ffffffc000ddeba0>] ping_common_sendmsg+0x50/0x108 net/ipv4/ping.c:674
[<ffffffc000dded30>] ping_v4_sendmsg+0xd8/0x698 net/ipv4/ping.c:714
[<ffffffc000dc91dc>] inet_sendmsg+0xe0/0x12c net/ipv4/af_inet.c:749
[< inline >] __sock_sendmsg_nosec net/socket.c:624
[< inline >] __sock_sendmsg net/socket.c:632
[<ffffffc000cab61c>] sock_sendmsg+0x124/0x164 net/socket.c:643
[< inline >] SYSC_sendto net/socket.c:1797
[<ffffffc000cad270>] SyS_sendto+0x178/0x1d8 net/socket.c:1761
CVE-2016-8399
Reported-by: Qidan He <i@flanker017.me>
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tsq_flags being in the same cache line than sk_wmem_alloc
makes a lot of sense. Both fields are changed from tcp_wfree()
and more generally by various TSQ related functions.
Prior patch made room in struct sock and added sk_tsq_flags,
this patch deletes tsq_flags from struct tcp_sock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a likely() in tcp_mtu_probe() moves its code which used to
be inlined in front of tcp_write_xmit()
We still have a cache line miss to access icsk->icsk_mtup.enabled,
we will probably have to reorganize fields to help data locality.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always allow the two first skbs in write queue to be sent,
regardless of sk_wmem_alloc/sk_pacing_rate values.
This helps a lot in situations where TX completions are delayed either
because of driver latencies or softirq latencies.
Test is done with no cache line misses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under high load, tcp_wfree() has an atomic operation trying
to schedule a tasklet over and over.
We can schedule it only if our per cpu list was empty.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under high stress, I've seen tcp_tasklet_func() consuming
~700 usec, handling ~150 tcp sockets.
By setting TCP_TSQ_DEFERRED in tcp_wfree(), we give a chance
for other cpus/threads entering tcp_write_xmit() to grab it,
allowing tcp_tasklet_func() to skip sockets that already did
an xmit cycle.
In the future, we might give to ACK processing an increased
budget to reduce even more tcp_tasklet_func() amount of work.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of atomically clear TSQ_THROTTLED and atomically set TSQ_QUEUED
bits, use one cmpxchg() to perform a single locked operation.
Since the following patch will also set TCP_TSQ_DEFERRED here,
this cmpxchg() will make this addition free.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cleanup, to ease code review of following patches.
Old 'enum tsq_flags' is renamed, and a new enumeration is added
with the flags used in cmpxchg() operations as opposed to
single bit operations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that update_suffix can be expensive when it is called
on a large node in which most of the suffix lengths are the same. The time
required to add 200K entries had increased from around 3 seconds to almost
49 seconds.
In order to address this we need to move the code for updating the suffix
out of resize and instead just have it handled in the cases where we are
pushing a node that increases the suffix length, or will decrease the
suffix length.
Fixes: 5405afd1a3 ("fib_trie: Add tracking value for suffix length")
Reported-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Robert Shearman <rshearma@brocade.com>
Tested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It wasn't necessary to pass a leaf in when doing the suffix updates so just
drop it. Instead just pass the suffix and work with that.
Since we dropped the leaf there is no need to include that in the name so
the names are updated to node_push_suffix and node_pull_suffix.
Finally I noticed that the logic for pulling the suffix length back
actually had some issues. Specifically it would stop prematurely if there
was a longer suffix, but it was not as long as the original suffix. I
updated the code to address that in node_pull_suffix.
Fixes: 5405afd1a3 ("fib_trie: Add tracking value for suffix length")
Suggested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Robert Shearman <rshearma@brocade.com>
Tested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes use of nf_ct_netns_get/put added in previous patch.
We add get/put functions to nf_conntrack_l3proto structure, ipv4 and ipv6
then implement use-count to track how many users (nft or xtables modules)
have a dependency on ipv4 and/or ipv6 connection tracking functionality.
When count reaches zero, the hooks are unregistered.
This delays activation of connection tracking inside a namespace until
stateful firewall rule or nat rule gets added.
This patch breaks backwards compatibility in the sense that connection
tracking won't be active anymore when the protocol tracker module is
loaded. This breaks e.g. setups that ctnetlink for flow accounting and
the like, without any '-m conntrack' packet filter rules.
Followup patch restores old behavour and makes new delayed scheme
optional via sysctl.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
so that conntrack core will add the needed hooks in this namespace.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
MASQUERADE, S/DNAT and REDIRECT already call functions that depend on the
conntrack module.
However, since the conntrack hooks are now registered in a lazy fashion
(i.e., only when needed) a symbol reference is not enough.
Thus, when something is added to a nat table, make sure that it will see
packets by calling nf_ct_netns_get() which will register the conntrack
hooks in the current netns.
An alternative would be to add these dependencies to the NAT table.
However, that has problems when using non-modular builds -- we might
register e.g. ipv6 conntrack before its initcall has run, leading to NULL
deref crashes since its per-netns storage has not yet been allocated.
Adding the dependency in the modules instead has the advantage that nat
table also does not register its hooks until rules are added.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
currently aliased to try_module_get/_put.
Will be changed in next patch when we add functions to make use of ->net
argument to store usercount per l3proto tracker.
This is needed to avoid registering the conntrack hooks in all netns and
later only enable connection tracking in those that need conntrack.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
since adf0516845 ("netfilter: remove ip_conntrack* sysctl compat code")
the only user (ipv4 tracker) sets this to an empty stub function.
After this change nf_ct_l3proto_pernet_register() is also empty,
but this will change in a followup patch to add conditional register
of the hooks.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_UDPLITE is no more a tristate. When set to y,
connection tracking support for UDPlite protocol is built-in into
nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_udplite,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| udplite| ipv4 | ipv6 |nf_conntrack
---------++--------+--------+--------+--------------
none || 432538 | 828755 | 828676 | 6141434
UDPlite || - | 829649 | 829362 | 6498204
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_SCTP is no more a tristate. When set to y, connection
tracking support for SCTP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_sctp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| sctp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 498243 | 828755 | 828676 | 6141434
SCTP || - | 829254 | 829175 | 6547872
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David Ahern