Multiple Discovery Fixes:
- Fix race on discovery due to link events coinciding with vport_delete.
- Use NLP_FABRIC state to filter out switch-based pseudo initiators that
reuse the same WWNs.
- Correct erroneous setting of DID=0 in lpfc_matchdid()
- Correct extra reference count that was in the lookup path for the
remoteid from an unsolicited ELS.
- Correct double-free bug in els abort path.
- Correct FDMI server discovery logic for switch that return a WWN of 0.
- Fix bugs in ndlp mgmt when a node changes address
- Correct bug that did not delete RSCNs for vports upon link transitions
- Fix "0216 Link event during NS query" error which pops up when vports
are swapped to different switch ports.
- Add sanity checks on ndlp structures
- Fix devloss log message to dump WWN correctly
- Hold off mgmt commands that were interferring with discovery mailbox cmds
- Remove unnecessary FC_ESTABLISH_LINK logic.
- Correct some race conditions in the worker thread, resulting in devloss:
- Clear the work_port_events field before handling the work port events
- Clear the deferred ring event before handling a deferred ring event
- Hold the hba lock when waking up the work thread
- Send an acc for the rscn even when we aren't going to handle it
- Fix locking behavior that was not properly protecting the ACTIVE flag,
thus allowing mailbox command order to shift.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous fixes:
- Fix ERRATT flag which was overlapping
- Allow RESTART mbx commands through when stopped.
- Accept incoming PLOGI when connected to an N_Port.
- Fix NPort to NPort pt2pt problems: ADISC and reg_vpi issues
- Fix vport unloading error that erroneously cleaned up RSCN buffers
- Fix memory leak during repeated unloads - in mbox handling
- Fix link bounce vs FLOGI race conditions
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct ndlp referencing issues:
- Fix ndlp kref issues due to race conditions between threads
- Fix cancel els delay retry event which missed an ndlp reference count
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Based on a patch from Ingo Molnar <mingo@elte.hu> as he pointed out that
I wrongly missed this.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts users of pci_enable_device_bars() to the new
pci_enable_device_{io,mem} interface.
The new API fits nicely, except maybe for the QLA case where a bit of
code re-organization might be a good idea but I prefer sticking to the
simple patch as I don't have hardware to test on.
I'll also need some feedback on the cs5520 change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch written by Tomohiro Kusumi and submitted to
linux-scsi:
http://marc.info/?l=linux-scsi&m=118673720712152&w=2
The original patch comment:
This patch makes Emulex lpfc driver legacy I/O port free.
It has already been acked quite long time ago.
So I resubmit the patch.
http://lkml.org/lkml/2006/11/22/28
Current lpfc driver is already using pci_select_bars()
and pci_enable_device_bars() when the PCI bus has been reset.
So I think this patch should also be acked.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com>
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Fixes:
- Fix a couple of sparse complaints
- Reset the FCP recovery flag when the node is not a FCP2 device.
- Speed up offline prep delays
- Fixed a memory leak in lpfc_mem_alloc failure path
- Fixed external loopback test.
- Fixed error code returned from the driver when HBA is over heated.
- Correct Max NPIV vport to limits read from adapter
- Add missing locks around fc_flag and FC_NEEDS_REG_VPI
- Add missing hba ids for device identification
- Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands
- Changed all temperature event messages from warning to error
- Fix reporting of link speed when link is down
- Added support for MBX_WRITE_WWN mailbox command
- Change del_timer_sync() in ISR to del_timer() in interrupt handler
- Correct instances of beXX_to_cpu() that should be cpu_to_beXX()
- Perform target flush before releasing node references on module unload
- Avoid bogus devloss_tmo messages when driver unloads
- Fix panic when HBA generates ERATT interupt
- Fix mbox race condition and a workaround on back-to-back mailbox commands
- Force NPIV off for pt2pt mode between 2 NPorts
- Stop worker thread before removing fc_host.
- Fix up discovery timeout error case due to missing clear_la
- Tighten mailbox polling code to speed up detection of fast completions
- Only allow DUMP_MEMORY if adapter offline due to overtemp errors
- Added extended error information to the log messages in chip init.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add parameters to enable and disable heartbeat and hba resets
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Discovery/ELS Fixes:
- Delay free's of ELS requests if adapter reject conditions
- Fix concurrent PLOGI vs ADISC state handling
- Add retry mechanism for GFF_ID
- Correct some illegal state transitions around RSCN timeouts
- Fix missing return in FAN handling
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Temperature handling fix - return proper error code indicator for applications
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Small Fixes - part 2
- Fix ndlp left in PLOGI state after link up
- Fix cannot rcv unsol ELS frames after running HBA resets for a few minutes
- Fix HBQ buffer_count implemention
- Fix RPI leak
- Fix crash while deleting vports while HBA is reset
- Revert the FCP Fbits offset back to 7
- Fix panic when deleting vports
- Remove unused code in switch statement outside of a case
- Reject PLOGI from invalid PName or NName of 0
- Ignore PLOGI responses from WWPName or WWNName of 0
- Fix debugfs hbqinfo display for ppc
- Added 8G to list of supported speeds for sysfs parameter
- Defer ndlp cleanup to dev-loss timeout handler
- Added support for WRITE_VPARMS mailbox command by applications
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
FC Discovery Fixes:
- Fix up lpfc_drop_node() vs lpfc_nlp_not_used() usage
- Clear ADISC flag when unregistering RPI and REMOVE ndlps if in recovery.
- Fix usage of UNUSED list and ndlps
- Fix PLOGI race conditions
- Reset link if NameServer PLOGI errors occur
- Synchronize GID_FT queries with PLOGI receptions
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Small Fixes - part 1
- Fix typo kmzlloc -> kzalloc
- Fix discovery ndlp use after free panic
- Fix link event causing flood of 0108 messages
- Relieve some mbox congestion on link up with 100 vports
- Fix broken vport parameters
- Prevent lock recursion in logo_reglogin_issue
- Split uses of error variable in lpfc_pci_probe_one into retval and error
- Remove completion code related to dev_loss_tmo
- Remove unused LPFC_MAX_HBQ #define
- Don't compare pointers to 0 for sparse
- Make 2 functions static for sparse
- Fix default rpi cleanup code causing rogue ndlps to remain on the NPR list
- Remove annoying ELS messages when driver is unloaded
- Fix Cannot issue Register Fabric login problems on link up
- Remove LPFC_EVT_DEV_LOSS_DELAY
- Fix FC port swap test leads to device going offline
- Fix vport CT flags to only be set when accepted
- Add code to handle signals during vport_create
- Fix too many retries in FC-AL mode
- Pull lpfc_port_link_failure out of lpfc_linkdown_port
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
NPIV bug fixes:
- Remove vport params on physical hba when npiv is disabled
- Implement new DA_ID CT command to remove vport information from
the switch after delete. Some switches didn't clean this up unless
the physical link dropped.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for ASICs that report temperature. Temperature notices are
reported as events and logged. Temperature can be read via sysfs.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Clean up all instances of mixed tab-space indentation
- Clean up sparse build errors
- Add appropriate static's
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Fix vport ndlp ref counting errors
- Fix use after free of ndlp structure
- Use the correct flag to check for LOADING setting.
- Fix driver unload bugs (related to shost references) after link down or rscn
- Fix up HBQ initialization
- Fix port_list locking around driver unload.
- Fix references to hostdata as a phba
- Fix GFFID type offset to work correctly with big endian structure.
- Only call pci_disable_msi if the pci_enable_msi succeeded
- Fix vport_delete wait/fail if in discovery
- Put a reference on the nameservers ndlp when performing CT traffic.
- Remove unbalanced hba unlock.
- Fix up HBQ processing
- Fix lpfc debugfs discovery trace output for ELS rsp cmpl
- Send ADISC when rpi is 0
- Stop FDISC retrying forever
- Unable to retrieve correct config parameter for vport
- Fix sli_validate_fcp_iocb, sli_sum_iocb, sli_abort_iocb to be vport-aware.
- Fix index-out-of-range error in iocb. Spotted by Coverity.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rework the lpfc_printf_log() macro so that logging is enabled on a
per-vport basis. Used to be on a physical-port basis, thus logging
with large numbers of vports became a mess. Required redefinition of
the macro, and an update of every use.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Split attributes up into vport and non-vport attributes.
- Move vport specific cfg params to vport
Many of the vport-specific behaviors were still global attributes
on the physical port. Move them to the vport itself.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleans up a lot of bad behaviors that have been in this area a while
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_create_port':
drivers/scsi/lpfc/lpfc_init.c:1573: error: 'struct kobject' has no member named 'dentry'
Just remove the if check on this ... lpfc shouldn't be poking around
in kobject structures.
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_pci_probe_one':
drivers/scsi/lpfc/lpfc_init.c:1723: warning: unused variable 'retval'
And remove the unused variable.
Cc: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As suggested by Andrew, add pci_try_set_mwi(), which does not require
return-value checking.
- add pci_try_set_mwi() without __must_check
- make it return 0 on success, errno if the "try" failed or error
- review callers
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Following the NPIV support, the following changes have been accumulated
in the testing and qualification of the driver:
- Fix affinity of ELS ring to slow/deferred event processing
- Fix Ring attention masks
- Defer dev_loss_tmo timeout handling to worker thread
- Consolidate link down error classification for better error checking
- Remove unused/deprecated nlp_initiator_tmr timer
- Fix for async scan - move adapter init code back into pci_probe_one
context. Fix async scan interfaces.
- Expand validation of ability to create vports
- Extract VPI resource cnt from firmware
- Tuning of Login/Reject policies to better deal with overwhelmned targets
- Misc ELS and discovery fixes
- Export the npiv_enable attribute to sysfs
- Mailbox handling fix
- Add debugfs support
- A few other small misc fixes:
- wrong return values, double-frees, bad locking
- Added adapter failure heartbeat
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NPIV support is added to the driver. It utilizes the interfaces of
the fc transport for the creation and deletion of vports. Within the
driver, a new Scsi_Host is created for each NPIV instance, and is
paired with a new instance of a FC port. This allows N FC Port
elements to share a single Adapter.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NPIV support is only available via new adapter interface extensions,
termed SLI-3. This interface changes some of the basic behaviors such
as command and response ring element sizes and data structures, as
well as a change in buffer posting. Note: the new firmware extensions
are found only on our mid-range and enterprise 4Gig adapters - so NPIV
support is available only on these newer adapters. The latest firmware
can be downloaded from the Emulex support page.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver is reorganized to separate the handling of the adapter from
the handling of the FC port. Adapter handling includes submissions of
command requests, receiving responses, and managing adapter resources.
The FC port includes the discovery engine, login handling, and the
mapping of a Scsi_Host on the "port". Although not a large functional
change, as it touches core structures and functions, resulting in a
large text delta.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Added support for 8G speed and new HBAs.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for async scanning
Notes: This is the async scan patch to our driver from Matthew Wilcox.
The async scan logic is still subject to errors in insmod/rmmod, as
the async scan threads don't get shutdown when the module unloads
underneath them. See http://marc.info/?l=linux-scsi&m=117551999925582&w=2
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Collapse discovery lists to a single node list.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve diagnostic messages and change local loopback message to KERN_INFO
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Round 2 of Miscellaneous fixes:
- Ensure we don't prematurely re-enable IRQs in lpfc_sli_abort_fcp_cmpl().
- Prevent freeing of iocb after IOCB_TIMEDOUT error.
- Added code to cleanup REG_LOGIN mailbox command when a LOGO is received.
- Fix offline window where more work can sneak in after clearing work_ha
- Use target reset instead of LU reset in bus_device_reset_handler
- Fixed system hangs due to leaked host_lock.
- Fixed NULL pointer dereference during I/O with LIP.
- Fixed false iocb timeout.
- Fixed name server query response handling.
- Change rport dev_loss_tmo value when user change lpfc HBA's dev_loss_tmo.
- Fixed a memory leak in lpfc_sli_wake_mbox_wait.
- Fixed check for dropped frames.
- Removed hba queue depth calculation based on device PCI IDs
- Change min cr_count value specified in comment to agree with setting
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Reorganize lpfc_nlp_list() and callers to prepare for nodelist simplification.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc bug fixes and code cleanup:
- Fix system hang while running on systems with IOMMU
- Fix use after free issues with rports
- Don't free mailbox structure if it's still on the mboxq list
- Decrement txq_cnt rather than txcmplq_cnt when parsing the txq list
- Use msleep for long delays to prevent soft lockup bug check
- Don't remove node during dev_loss_tmo if discovery is active
- Fix memory leaks in get/reset statistics and link attention paths
- Fixed lpfc_ns_rsp to handle entire GID_FT response.
- mbox interface should use MAILBOX_CMD_SIZE rather than sizeof(MAILBOX_t)
- Fixed bug check in add_timer.
- Fixup messages 0116, 0117, and 0128 to report ELS I/O tag.
- Remove unused parameter to lpfc_cleanup.
- Change mailbox timeout handling.
- Remove unused buflist. Code cleanup.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have seen two cases where VPD on an emulex card has been incorrect
and we end up walking off the end of memory. It looks like someone made
an update (increased the length of a string) without increasing the
Length field. Then we do:
Length -= (3+i);
And since Length is unsigned it becomes very large and we loop forever
in the encapsulating:
while (Length > 0) {
If we make Length signed then we fall out of the loop and proceed on.
Its important to note we have only seen this in the lab and it may be
the only two cases of this in existence, but since the rest of the code
has been written to be resilient against bad VPD we may as well fix this
too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a PCI error is detected that cannot be recovered from, there
will be a double call of lpfc_pci_remove_one(), with the second call
resulting in a null-pointer dereference. The first call occurs in
lpfc_io_error_detected(), and the second call during pci device
remove. This patch eliminates the first call; its un-needed.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds PCI Error recovery support to the
Emulex Lightpulse Fibrechannel (lpfc) SCSI device driver.
Lightly tested at this point, works.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Bino.Sebastian@Emulex.Com
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc Fixes:
- Prevent references to NULL node list element in reset routines.
- Add missing IOCB types to switch tables
- Reset the card on Port Error 5
- Fix infinite loop in LUN reset
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver now allows both wwpn and wwnn to be set.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
To avoid continually updating the driver for new subsystem ids
(as adapter modules are proliferating), remove this 2nd level decode.
Genericize the reported Adapter names to be consistent across
Emulex product line.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add MSI (Message Signalled Interrupts) support
Actual use must be enabled via the new module parameter "lpfc_use_msi"
Defaults to no use
Many thanks to Frederic Temporelli who implemented the initial patch.
Signed-off-by: Frederic Temporelli <frederic.temporelli@ext.bull.net>
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It was not accounted for in the fast/slow rings.
Genericize the implementation and control it via sysfs
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for a new lpfc soft_wwpn sysfs attribute
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support to post events via new FC event interfaces
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc Bug Fixes:
- Cap MBX_DOWN_LINK command timeout to 60 seconds
- Fix double free of ndlp object
- Don't free mbox structures on error. The completion handlers expect to do so.
- Clear host attention work items when going offline
- Fixed discovery issues in multi-initiator environments.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Short bug fixes:
- Fix iocbq list corruption due to missing list_del's in ct handling
- Missing unlock in lpfc_sli_next_iotag()
- Fix initialization of can_queue value
- Differentiate sysfs mailbox errors with different codes.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc Fixes:
- Fix some sparse warnings - casts of address space
- Fix handling of the adapter registration string. Each invocation
was byteswapping, so every other adapter init attempt failed.
- Correct comments and default value for the lpfc_max_luns parameter
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add lpfc_sli_flush_mbox_queue() function and use it in lpfc_offline() call
to avoid deadlock on thread block.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct the wait in attachment that delays for topology discovery
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix txcmplq related panics on heavy IO while downloading firmware
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/nsp32.c
drivers/scsi/pcmcia/nsp_cs.c
Removal of randomness flag conflicts with SA_ -> IRQF_ global
replacement.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This removes the duplicate functionality which had been added to
the lpfc driver.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix sparse warnings: use NULL instead of 0 for pointers:
drivers/scsi/lpfc/lpfc_els.c:827:56: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_els.c:2781:18: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_els.c:2782:18: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_init.c:951:21: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_init.c:956:20: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Contains the following misc fixes:
- Fix build warnings
- Race condition in lpfc_workq_post_event() could corrupt phba->work_list.
- nlp_sid was not being initialized properly
- Fix some RSCN handling during the re-discovery after Link Up event.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix cleanup code in the lpfc_pci_probe_one() error code path.
This changes the original patch by:
- hardsetting the return value from lpfc_pci_probe_one() to
-ENODEV (negative value) if we fail attach
- removes the checks from lpfc_pci_remove_one() validating the
host and phba pointers as it's no longer needed.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use asynchronous ABTS completion to speed up abort completions
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce lpfc_reset_barrier() function for resets on dual channel adapters
Workaround for a hardware errata on dual channel asics. There is a
potential for the chip to lock up on a reset if a shared dma engine is in
use. The (ugly) work around requires a reset process which uses a mailbox
command to synchronize the independent channels prior to the reset to
avoid the issue. Unfortunately, the timing windows required to ensure this
workaround succeeds are very specific, meaning we can't release the cpu
during the barrier.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
PCI hrd_type should be obtained with pci_read_config_byte() macro
Driver keys off of this field to report the proper adapter type.
The pci subsystem explicitly clears the multiport bit in the copy of
the field given the driver. Thus, to properly name the card, obtain it
from config space.
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Derive supported speeds from LMT field in the READ_CONFIG
Driver was keying off internal cores. Use what the firmware reports instead.
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct use of the hostdata field in scsi_host
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed system panic in lpfc_sli_brdreset during dynamic add of LP11K
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Add functionality to run in polled mode only. Includes run time
attribute to enable mode.
- Enable runtime writable hba settings for coallescing and delay parameters
Customers have requested a mode in the driver to run strictly polled.
This is generally to support an environment where the server is extremely
loaded and is looking to reclaim some cpu cycles from adapter interrupt
handling.
This patch adds a new "poll" attribute, and the following behavior:
if value is 0 (default):
The driver uses the normal method for i/o completion. It uses the
firmware feature of interrupt coalesing. The firmware allows a
minimum number of i/o completions before an interrupt, or a maximum
time delay between interrupts. By default, the driver sets these
to no delay (disabled) or 1 i/o - meaning coalescing is disabled.
Attributes were provided to change the coalescing values, but it was
a module-load time only and global across all adapters.
This patch allows them to be writable on a per-adapter basis.
if value is 1 :
Interrupts are left enabled, expecting that the user has tuned the
interrupt coalescing values. When this setting is enabled, the driver
will attempt to service completed i/o whenever new i/o is submitted
to the adapter. If the coalescing values are large, and the i/o
generation rate steady, an interrupt will be avoided by servicing
completed i/o prior to the coalescing thresholds kicking in. However,
if the i/o completion load is high enough or i/o generation slow, the
coalescion values will ensure that completed i/o is serviced in a timely
fashion.
if value is 3 :
Turns off FCP i/o interrupts altogether. The coalescing values now have
no effect. A new attribute "poll_tmo" (default 10ms) exists to set
the polling interval for i/o completion. When this setting is enabled,
the driver will attempt to service completed i/o and restart the
interval timer whenever new i/o is submitted. This behavior allows for
servicing of completed i/o sooner than the interval timer, but ensures
that if no i/o is being issued, then the interval timer will kick in
to service the outstanding i/o.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Release task management command before counting outstanding commands.
TMF was being erroneously counted as an active outstanding command.
- Serialize EH calls and block requests when EH function is running.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cause: Link bounces were causing discovery ELS's to be killed.
Driver was not properly flushing ELS commands upon the subsequent
link bounces. Thus, processing of ELS post link bounce erroneously
assumed discovery failure and device loss.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Miscellaneous Cleanups:
- Remove ProgType READ_REV mailbox command value check in lpfc_config_port_prep.
- Convert simple printk to an lpfc_printf_log in queuecommand.
- Modify lpfc_abort_handler message 0749 to display more accurate text and data.
- Minor style cleanup: fix 3 long lines in lpfc_hw.h
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Current upstream 'allmodconfig' build is broken. This is the obvious
patch...
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the drivers/scsi/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/scsi/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Return FAILED from eh_ routines if command(s) is(are) not completed
There were scenarios where we may have returned from the error
handlers prior to all affected commands being flushed to the midlayer.
Add changes to ensure this doesn't happen.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: James Smart <James.Smart@emulex.com>
There were scenarios where the error handlers could reuse an iotag
value of an active io. Remove all possibility of this by
pre-assigning iotag resources to command resources.
Signed-off-by: James Smart <James.Smart@emulex.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix for "Unknown IOCB command Data: x0 x3 x0 x0" messages and
inability to see devices
On some platforms, the host-memory based ring mgmt area was not
zero. Also, driver wasn't manipulating the entire 32bits of the ring
pointers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update adapter names to match Emulex naming conventions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).
It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.
So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions. Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.
One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance. However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Acked-by: Smart, James <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace use of lpfc_put_lun with midlayer's int_to_scsilun
Remove driver's local definition of lpfc_put_lun (which converts an
int back to a 64-bit LUN) and replace it's use with the recently added
int_to_scsilun function provided by the midlayer.
Note: Embedding midlayer structure in our structure caused
need for more files to include midlayer headers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix panic in lpfc_get_stats()
Symptoms: Panic on sysfs stats access
Cause: In lpfc_get_stats() we are writing to memory that we do not
own.
Fix: Fix our stats structure allocation. Embed phba->link_stats in
struct lpfc_hba and stop treating it like rogue structure.
Note: Embedding midlayer/transport structure in our structure caused
need for more files to include midlayer/transport headers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update copyright notice text and include year 2005.
Add Copyright notice for Christoph Hellwig to several files: lpfc.h
lpfc_attr.c lpfc_els.c lpfc_hbadisc.c lpfc_init.c lpfc_mbox.c
lpfc_mem.c lpfc_nportdisc.c lpfc_scsi.c lpfc_sli.c
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix driver not seeing LP6000. Fix: add PCI id to the pci_device_id
table and a short description for the HBA in get_hba_model_desc().
Also add a default clause to the switch statement that parses the
various PCI ID's.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Smart