Add idr_destroy() calls to the module_exit() functions of the four IB
driver modules that use idrs, so we don't leak idr_layer_cache objects
when these modules are unloaded.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We should always re-arm an event queue's interrupt in
mthca_tavor_interrupt() if the corresponding bit is set in the event cause
register (ECR), even if we didn't find any entries in the EQ. If we don't,
then there's a window where we miss an EQ entry and then get stuck because
we don't get another EQ event.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should always re-arm an event queue's interrupt in
mthca_tavor_interrupt() if the corresponding bit is set in the event
cause register (ECR), even if we didn't find any entries in the EQ.
If we don't, then there's a window where we miss an EQ entry and then
get stuck because we don't get another EQ event.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add missing "break" in switch statement. Without the break, the
CM ended up always falling through and setting every connection
request to use RC transport, which meant that UC connections
didn't work.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Avoid entering a QP as member of a multicast group multiple times.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We keep IB device structures around until the last sysfs reference is
gone, but we shouldn't ask the low-level driver to do anything after
the LLD unregisters the device. To handle this, check the reg_state
field and just fail sysfs show() requests if the device has already
been unregistered.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make the type parameter of mthca_alloc_db() be an enum mthca_db_type
instead of an int. This doesn't have any practical effect but
documents the functions a little better.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use jiffies_to_msecs() so we print a human-readable time so
we don't have to worry about what HZ is configured to, and
print out a few values to make post-mortem analysis easier.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Bind communication identifiers to a device to support device removal.
Export per HCA CM devices to userspace.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Add kernel support for userspace calling poll CQ, request CQ
notification, post send, post receive, post SRQ receive, create AH and
destroy AH commands. These commands allow us to support userspace
verbs for devices that can't perform these operations directly from
userspace (eg the PathScale HCA).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Give each device a uverbs_cmd_mask, so that a low-level driver can
control which methods may be called on behalf of userspace.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the SA query module's initialization fails for a device, then that
device won't have a struct ib_sa_device associated. We should fail SA
queries in that case, rather than blindly dereferencing the NULL
pointer we get back from ib_get_client_data().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_create_qp() no longer creates IPoIB's QP, so it shouldn't
destroy the QP on failure -- that unwinding happens elsewhere, so the
current code can cause a double free. While we're at it, the
function's name should match what it actually does, so rename it to
ipoib_init_qp().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check the sizes of CQs, QPs and SRQs when creating objects, and fail
instead of creating too-big queues. Also return real limits instead
of just plausible-sounding values from mthca_query_device().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a bug in ib_mad_init_device(): if ib_agent_port_open() fails
for a given port, then the current code doesn't call ib_mad_port_close()
for that port.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hardware relies on us keeping one extra work request that never
gets used in SRQs. Add checks to the SRQ work request posting
functions so that they fail when someone is about to use up that extra
work request, rather than when someone uses the very last work request.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Our hardware supports generating an event when the number of receives
posted to a shared receive queue (SRQ) falls below a user-specified
limit. Implement mthca_modify_srq() to arm the limit, and add code to
handle dispatching SRQ events when they occur.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reject userspace memory registrations with invalid permission flags:
"local write" is required if "remote write" or "remote atomic" is also
requested.
Pointed out by Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add code to fill in the bad_pkey_cntr, max_mtu, active_mtu and
subnet_timeout fields in mthca_query_port().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add abi_version attribute to uverbs class devices to allow for
ABI versioning of device-specific interfaces.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
By waiting to add resources to our lists until after the last
operation that can fail, we don't have to remove them from their lists
in the error path. Also, we should hold the idr mutex until we know
whether resource creation has succeed or failed, to avoid someone
finding a resource in our table before we're ready.
Loosely based on work by Robert Walsh <rjwalsh@pathscale.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Introduce new userspace verbs ABI version 3. This eliminates some
unneeded commands, and adds support for user-created completion
channels. This cleans up problems with file leaks on error paths, and
also makes sure that file descriptors are always installed into the
correct process.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Return correct atomic capability flag from mthca query function.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add checks so that we only allow multicast attach/detach with
a valid multicast GID and the correct QP type.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remember to free the multicast group context memory table.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rename IPoIB driver's path_lookup() to ipoib_path_lookup() to avoid a
clashes with the kernel global path_lookup(). We don't hit this with
the current kernel source, but some external patches seem to trigger
this, and it's cleaner to avoid clashing with global names anyway.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
refs/heads/for-linus
The IB spec defines the field to be 32 bits, not 16 bits.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When allocating a table for mem-free HCA context, don't assume that
obj_size * nobj is an even multiple of MTHCA_TABLE_CHUNK_SIZE. In
particular, make sure we allocate at least one slot even if the table
is smaller than MTHCA_TABLE_CHUNK_SIZE.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Al Viro pointed out that the current IB userspace verbs interface
allows userspace to cause mischief by closing file descriptors before
we're ready, or issuing the same command twice at the same time. This
patch closes those races, and fixes other obvious problems such as a
module reference leak.
Some other interface bogosities will require an ABI change to fix
properly, so I'm deferring those fixes until 2.6.15.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The loop in mthca_map_cmd() would fill one entry past the end of the
mailbox buffer before calling the firmware command.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We should use the first word of the clear interrupt register if
the bit we're after is < 32, not < 31.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If we allocate a bunch of doorbell records and then free them, we'll
end up with completely empty pages, which we then free. However, when
we come back to allocate more doorbell pages, we have to reallocate
those empty pages rather than always trying to take a slot that we've
never used. If we don't, we eventually use up every slot and fail to
allocate a doorbell record, even though we have plenty of free space.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Based on simplification idea from Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up code by using enums instead of hard-coded magic numbers.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_mcast_restart_task() is always called from within the
single-threaded IPoIB workqueue, so flushing the workqueue from within
the function can lead to a recursion overflow. But since we're
running in a single-threaded workqueue, we're already synchronized
against other items in the workqueue, so just get rid of the flush in
ipoib_mcast_restart_task().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to subtract off the header length from our payload
length when sending multi-packet SA messages.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Userspace SRQs don't have a buffer allocated for them in the kernel, so
it doesn't make sense to set srq->last during initialization. In fact,
this can crash trying to follow a nonexistent buffer pointer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error handling paths in mthca_tavor_post_srq_recv() and
mthca_arbel_post_srq_recv() are quite bogus, the result of a
screwed up merge. Fix them so they work as intended.
Pointed out by Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mthca_create_eq(), we call get_eqe() before setting eq->nent. This
is wrong, because get_eqe() uses eq->nent. Fix this, and clean up the
code a little while we're at it. (We got lucky with the current code,
because eq->nent was cleared to 0, which get_eqe() made happen to do
the right thing)
Pointed out by Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We got a little mixed up with what the backoff member holds in the
IPoIB multicast group structure: sometimes it was used as a number of
seconds, and sometimes it was used as a number of jiffies. Fix the
code so that backoff is always in seconds.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix posting first WQE for mem-free HCAs: we need to link to previous
WQE even in that case. While we're at it, simplify code for
Tavor-mode HCAs. We don't really need the conditional test there
either; we can similarly always link to the previous WQE.
Based on Michael S. Tsirkin's analogous fix for userspace libmthca.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hardware reads the ACK timeout field from the most significant 5
bits of struct mthca_qp_path's ackto field, not the least significant
bits. This fix has the driver put the timeout in the right place.
Without this, we get a timeout that is 2^8 times too small.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since ipoib uses queue_delayed_work to run flush task on port state events,
it must flush scheduled work after unregistering the event handler.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the CM REQ handling function gets to error2, then it frees
cm_id_priv->timewait_info. But the next line goes through
ib_destroy_cm_id() -> ib_send_cm_rej() -> cm_reset_to_idle(),
which ends up calling cm_cleanup_timewait(), which dereferences the
pointer we just freed. Make sure we clear cm_id_priv->timewait_info
after freeing it, so that doesn't happen.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Changes to CM to support CM and port redirection (REJ reason 24).
Signed-off-by: John Kingman <kingman <at> storagegear.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
completion events after destroying a CQ, QP or SRQ. We do this by
sweeping the event lists before returning from a destroy calls, and
then return the number of events already reported before the destroy
call. This allows userspace wait until it has processed all events
for an object returned from the kernel before it frees its context for
the object.
The ABI of the destroy CQ, destroy QP and destroy SRQ commands has to
change to return the event count, so bump the ABI version from 1 to 2.
The userspace libibverbs library has already been updated to handle
both the old and new ABI versions.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SA: Move SA attributes to ib_sa.h so are accessible to more than
sa_query.c. Also, remove deprecated attributes and add one missing one.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new config option INFINIBAND_USER_MAD to control whether we
build ib_umad. Change INFINIBAND_USER_VERBS to INFINIBAND_USER_ACCESS,
and have it control ib_ucm and ib_uat as well as ib_uverbs.
Signed-off-by: James Lentini <jlentini@netapp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Fix payload length of middle RMPP sent segments. Middle payload
lengths should be 0 on the send side.
(This is perhaps a compliance and should not be an interop issue as
middle payload lengths are supposed to be ignored on receive).
- Fix length in first segment of multipacket sends
(This is a compliance issue but does not affect at least OpenIB to
OpenIB RMPP transfers).
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When we modify a QP to the RESET state, completely clean up the QP
so that it is really and truly reset.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Add user specified context to all uCM events. Users will not retrieve
any events associated with the context after destroying the corresponding
cm_id.
- Provide the ib_cm_init_qp_attr() call to userspace clients of the CM.
This call may be used to set QP attributes properly before modifying the QP.
- Fixes some error handling synchonization and cleanup issues.
- Performs some minor code cleanup.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Using ib_get_client_data in SA event handler performs a list scan.
It's better to use container_of to get the sa device directly.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the InfiniBand headers from drivers/infiniband/include to include/rdma.
This allows InfiniBand-using code to live elsewhere, and lets us remove the
ugly EXTRA_CFLAGS include path from the InfiniBand Makefiles.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently we may have work scheduled in default kernel workqueue when
the device is going down. The device could get freed before this
workqueue gets serviced. I am actually seeing this causing system
hangs.
The following patch fixes this by using ipoib_workqueue which gets
flushed when the device is going down.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix deadlock condition resulting from trying to destroy a cm_id
from the context of a CM thread. The synchronization around the
ucm context structure is simplified as a result, and some simple
code cleanup is included.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Always make sure that the full membership bit is set in the P_Keys
that IPoIB uses. This makes sure that all hosts join the correct
multicast groups so that hosts that are partial partition members
can talk to the rest of the network.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When creating a table in context memory where the table is smaller
than our chunk size, we don't want to allocate and map a full chunk.
Instead, allocate just enough memory to cover the table.
This can be pretty simple because all tables are a power-of-2 size, so
either the table is a multiple of the chunk size, or it's smaller than
one chunk.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the definitions of the WQE structures from mthca_qp.c into
mthca_wqe.h, so that we'll be able to share them when we add the
SRQ code in mthca_srq.c.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Mem-free HCAs never generate error CQEs that complete multiple WQEs,
so just skip the call to mthca_free_err_wqe() for them rather than
having logic to handle the mem-free case in mthca_free_err_wqe().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up the allocation of memory for queues by factoring out the
common code into mthca_buf_alloc() and mthca_buf_free(). Now CQs and
QPs share the same queue allocation code, which we'll also use for SRQs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add SRQ support to userspace verbs module. This adds several commands
and associated structures, but it's OK to do this without bumping the
ABI version because the commands are added at the end of the list so
they don't change the existing numbering. There are two cases to
worry about:
1. New kernel, old userspace. This is OK because old userspace simply
won't try to use the new SRQ commands. None of the old commands are
changed.
2. Old kernel, new userspace. This works perfectly as long as
userspace doesn't try to use SRQ commands. If userspace tries to
use SRQ commands, it will get EINVAL, which is perfectly
reasonable: the kernel doesn't support SRQs, so we couldn't do any
better.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the max_msg_sz port property correctly in mthca's port_query
function. Also zero out the attr struct so that we don't leave
any other members uninitialized.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When we call the INIT_IB firmware command to bring up a port, use
the actual port width capability returned by the QUERY_DEV_LIM
command instead of always trying to enable both 1X and 4X. This
fixes breakage seen when the firmware is build to allow 4X only.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
changing CONFIG_LOCALVERSION rebuilds too much, for no appearent reason.
Remove unneeded includes of <linux/version.h>.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change ib_mad_thread_completion_handler to conform to ib_comp_handler
declaration.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the generic key_to_hw_index() function instead of the Arbel-specific
version in mthca_free_region().
Signed-off-by: Guy German <guyg@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make sure that all FMRs are unmapped before we deallocate them so that
we don't leak references to our protection domain when destroying an
FMR pool. (Bug reported by Guy German <guyg@voltaire.com>)
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for reporting HCA board ID returned from QUERY_ADAPTER
firmware command through sysfs.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make some lawyers happy and add copyright notices for people who
forgot to include them when they actually touched the code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Update FW versions in mthca according to July 05 Mellanox release
Signed-off-by: Tziporet Koren <tziporet@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a use-after-free bug in userspace verbs cleanup: we can't touch
mr->device after we free mr by calling ib_dereg_mr().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
infiniband uses PCI helpers all over the place (including the core parts) and
won't build without PCI.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RARP replies are another valid case where IPoIB may need to send a
unicast packet with no neighbour structure.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reject code 24 is port and CM redirection, not just port redirection.
Port redirection alone is code 25.
Therefore we should rename code 24 to IB_CM_REJ_PORT_CM_REDIRECT and
use IB_CM_REJ_PORT_REDIRECT for code 25.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only print debug messages when debug_level is set.
Eliminate NULL checks prior to calling kfree.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Libor Michalek <libor@topspin.com>
Eliminate sparse warnings in SA client
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hook up userspace CM to the make system
Signed-off-by: Libor Michalek <libor@topspin.com>
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Include the patch openib-general changing class_simple to class.
Signed-off-by: Tom Duffy <tduffy@sun.com>
Cc: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add kernel portion of user CM implementation
Signed-off-by: Libor Michalek <libor@topspin.com>
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the header file for user space CM. This file defines the ABI used by the
CM for kernel/user communication.
Signed-off-by: Libor Michalek <libor@topspin.com>
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roland Dreier