This patch migrates the vpfe driver to use v4l2_fh for
priority handling.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch migrates the vpbe driver to use v4l2_fh for
priority handling. This also fixes v4l2-compliance test.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the PCI-8604PW card equipped with four 878A.
It is unknown who the manufacturer of this card is and no drivers were
available during development of the patch. According to images found
online, the card is originally sold with Linux DVR software.
A CPLD on the card prevents the 878A from requesting access to the
bus until an initialization sequence has been issued via GPIOs. The
implemented sequence uses the minimum number of GPIOs needed to
successfully unlock bus access. As there are many more GPIOs connected
to the CPLD, it is very likely that some of the others have an influence
on the bus arbitration scheduling. This should be investigated further
in case of performance issues.
The tested card contains an EEPROM on one of the 878A, but it is
completely empty (i.e. contains only 0xff), so it is not possible
to detect the card.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Tested-by: Robert Longbottom <rongblor@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In core_init make sure access to EDID DDC lines are disabled
before chip is powered up. Also DISABLE_AUTO_EDID before power up.
The correct setting is applied later when setting the EDID.
Some sources (MAC) kept on reading EDID even when Hotplug was low
and in the short period in core_init before the DDC lines was enabled
read a corrupt EDID.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This was the reason for enabling the HDMI/DVI-D mode irq in the first place.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the use of __user in the check_array_args() prototype: instead of
using 'void * __user *' you should use 'void __user **' for sparse to
understand this correctly.
This also required the use of __force in the '*kernel_ptr = user_ptr'
assignment.
Also replace a wrong cast (void *) with the correct one (void **)
in check_array_args().
This fixes these sparse warnings:
drivers/media/v4l2-core/v4l2-ioctl.c:2284:35: warning: incorrect type in assignment (different address spaces)
drivers/media/v4l2-core/v4l2-ioctl.c:2301:35: warning: incorrect type in assignment (different address spaces)
drivers/media/v4l2-core/v4l2-ioctl.c:2319:35: warning: incorrect type in assignment (different address spaces)
drivers/media/v4l2-core/v4l2-ioctl.c:2386:57: warning: incorrect type in argument 4 (different address spaces)
drivers/media/v4l2-core/v4l2-ioctl.c:2420:29: warning: incorrect type in assignment (different address spaces)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sparse generated a bunch of errors like this:
drivers/media/v4l2-core/videobuf2-core.c:2045:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:136:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:151:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:168:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:183:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:185:9: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:385:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1115:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1268:33: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1270:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1315:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1324:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1396:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1457:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1482:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1484:9: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1523:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1525:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1815:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1828:17: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1914:25: error: incompatible types in conditional expression (different base types)
drivers/media/v4l2-core/videobuf2-core.c:1944:9: error: incompatible types in conditional expression (different base types)
These are caused by the call*op defines which do something like this:
(ops->op) ? ops->op(args) : 0
which is OK as long as op is not a void function, because in that case one part
of the conditional expression returns void, the other an integer. Hence the sparse
errors.
I've replaced this by introducing three variants of the call_ macros:
call_*op for int returns, call_void_*op for void returns and call_ptr_*op for
pointer returns.
That's the bad news. The good news is that the fail_*op macros could be removed
since the call_*op macros now have enough information to determine if the op
succeeded or not and can increment the op counter only on success. This at least
makes it more robust w.r.t. future changes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was some frequency calculation overflows which caused tuning
failure on 32-bit architecture. Use 64-bit numbers where needed in
order to avoid calculation overflows.
Thanks for the Finnish person, who asked remain anonymous, reporting,
testing and suggesting the fix.
Cc: <stable@vger.kernel.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VIDEO_TIMBERDALE selects TIMB_DMA which itself depends on
MFD_TIMBERDALE, so VIDEO_TIMBERDALE should either select or depend on
MFD_TIMBERDALE as well. I chose to make it depend on it because I
think it makes more sense and it is consistent with what other options
are doing.
Adding a "|| HAS_IOMEM" to the TIMB_DMA dependencies silenced the
kconfig warning about unmet direct dependencies but it was wrong:
without MFD_TIMBERDALE, TIMB_DMA is useless as the driver has no
device to bind to.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch does not modify existing drivers. It adds subdriver
to gspca for DTCS033 (Scopium) webcam for astrophotography.
The patch adds dtcs033.c and modifies Kconfig and Makefile.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sn9c102 driver is deprecated. It was moved to staging in
anticipation of its removal in a future kernel version. However, USB
devices 0C45:6024 and 0C45:6025 are still handled by sn9c102 when
both sn9c102 and gspca_sonixb are enabled.
We must migrate all the users of these devices to the gspca_sonixb
driver now, so that it gets sufficient testing before the sn9c102
driver is finally phased out.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
from commit-id: b3379c6201
"vb2: only call start_streaming if sufficient buffers are queued"
the vb2 framework warns on (WARN_ON()) if all the active buffers
are not released when streaming is stopped, initially the vb2 silently
released the buffer internally if the buffer was not released by
the driver.
This patch fixes following issue:
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:2011 __vb2_queue_cancel+0x1a0/0x218()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpbe_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252e0c>] (__vb2_queue_cancel+0x1a0/0x218)
[<c0252e0c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpbe_display_release+0x60/0x230)
[<c025a65c>] (vpbe_display_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:1095 vb2_buffer_done+0x1e0/0x224()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpbe_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252c28>] (vb2_buffer_done+0x1e0/0x224)
[<c0252c28>] (vb2_buffer_done) from [<c0252e3c>] (__vb2_queue_cancel+0x1d0/0x218)
[<c0252e3c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpbe_display_release+0x60/0x230)
[<c025a65c>] (vpbe_display_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a2 ]---
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
from commit-id: b3379c6201
"vb2: only call start_streaming if sufficient buffers are queued"
the vb2 framework warns on (WARN_ON()) if all the active buffers
are not released when streaming is stopped, initially the vb2 silently
released the buffer internally if the buffer was not released by
the driver.
Also this patch moves the disabling of interrupts from relase() callback
to stop_streaming() callback as which needs to be done ideally.
This patch fixes following issue:
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:2011 __vb2_queue_cancel+0x1a0/0x218()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252e0c>] (__vb2_queue_cancel+0x1a0/0x218)
[<c0252e0c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:1095 vb2_buffer_done+0x1e0/0x224()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_display Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252c28>] (vb2_buffer_done+0x1e0/0x224)
[<c0252c28>] (vb2_buffer_done) from [<c0252e3c>] (__vb2_queue_cancel+0x1d0/0x218)
[<c0252e3c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a2 ]---
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
from commit-id: b3379c6201
"vb2: only call start_streaming if sufficient buffers are queued"
the vb2 framework warns on (WARN_ON()) if all the active buffers
are not released when streaming is stopped, initially the vb2 silently
released the buffer internally if the buffer was not released by
the driver.
Also this patch moves the disabling of interrupts from relase() callback
to stop_streaming() callback as which needs to be done ideally.
This patch fixes following issue:
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:2011 __vb2_queue_cancel+0x1a0/0x218()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_capture Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252e0c>] (__vb2_queue_cancel+0x1a0/0x218)
[<c0252e0c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2049 at drivers/media/v4l2-core/videobuf2-core.c:1095 vb2_buffer_done+0x1e0/0x224()
Modules linked in:
CPU: 0 PID: 2049 Comm: vpif_capture Tainted: G W 3.14.0-rc5-00414-ged97a6f #89
[<c000e3f0>] (unwind_backtrace) from [<c000c618>] (show_stack+0x10/0x14)
[<c000c618>] (show_stack) from [<c001adb0>] (warn_slowpath_common+0x68/0x88)
[<c001adb0>] (warn_slowpath_common) from [<c001adec>] (warn_slowpath_null+0x1c/0x24)
[<c001adec>] (warn_slowpath_null) from [<c0252c28>] (vb2_buffer_done+0x1e0/0x224)
[<c0252c28>] (vb2_buffer_done) from [<c0252e3c>] (__vb2_queue_cancel+0x1d0/0x218)
[<c0252e3c>] (__vb2_queue_cancel) from [<c02533a4>] (vb2_queue_release+0x14/0x24)
[<c02533a4>] (vb2_queue_release) from [<c025a65c>] (vpif_release+0x60/0x230)
[<c025a65c>] (vpif_release) from [<c023fe5c>] (v4l2_release+0x34/0x74)
[<c023fe5c>] (v4l2_release) from [<c00b4a00>] (__fput+0x80/0x224)
[<c00b4a00>] (__fput) from [<c00341e8>] (task_work_run+0xa0/0xd0)
[<c00341e8>] (task_work_run) from [<c001cc28>] (do_exit+0x244/0x918)
[<c001cc28>] (do_exit) from [<c001d344>] (do_group_exit+0x48/0xdc)
[<c001d344>] (do_group_exit) from [<c0029894>] (get_signal_to_deliver+0x2a0/0x5bc)
[<c0029894>] (get_signal_to_deliver) from [<c000b888>] (do_signal+0x78/0x3a0)
[<c000b888>] (do_signal) from [<c000bc54>] (do_work_pending+0xa4/0xb4)
[<c000bc54>] (do_work_pending) from [<c00096dc>] (work_pending+0xc/0x20)
---[ end trace 5faa75e8c2f8a6a2 ]---
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All YUV 422 has 16bit per pixels.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This fixes following build error:
CC drivers/media/i2c/s5c73m3/s5c73m3-core.o
CC drivers/md/dm-ioctl.o
CC net/ipv4/inet_lro.o
drivers/media/i2c/s5c73m3/s5c73m3-core.c: In function ‘s5c73m3_get_platform_data’:
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1619:2: error: implicit declaration of function ‘v4l2_of_get_next_endpoint’ [-Werror=implicit-function-declaration]
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1619:10: warning: assignment makes pointer from integer without a cast [enabled by default]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It printed a little bit too heavy looking error log "DVB: Unable to
find symbol rtl2832_sdr_attach()" when staging module was disabled.
Silence that error by introducing own version of dvb_attach() macro
without the error logging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832 SDR extension module is currently on staging. SDR module
headers were included from staging causing direct dependency staging
directory. As a solution, add needed headers to main driver.
Motivation of that change comes from Luis / driver backports project.
Reported-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Cc: backports@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Coverity, there's a potential risk of a division
by zero on some calls to jpeg_set_qual(), if quality is zero.
As quality can't be 0 or lower than that, adds an extra clause
to cover this special case.
Coverity reports: CID#11922280, CID#11922293, CID#11922295
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The dequed CAPTURE_MPLANE type buffers don't contain the flags that the
originally queued OUTPUT_MPLANE type buffers have. This breaks compliance.
Copy the source v4l2_buffer flags to the destination v4l2_buffer flags before
they are dequed.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vpe driver wasn't setting the correct field parameter for dequed CAPTURE
type buffers for the case where the captured output is progressive.
Set the field to V4L2_FIELD_NONE for the completed destination buffers when
the captured output is progressive.
For OUTPUT type buffers, a queued buffer's field is forced to V4L2_FIELD_NONE
if the pixel format(configured through s_fmt for the buffer type
V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE specifies) the field type isn't interlaced.
If the pixel format specified was V4L2_FIELD_ALTERNATE, and the queued buffer's
field isn't V4L2_FIELD_TOP or V4L2_FIELD_BOTTOM, the vb2 buf_prepare op returns
an error.
This ensures compliance, and that the dequeued output and captured buffers
contain the field type that the driver used internally.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Zero out the reserved formats in v4l2_pix_format_mplane and
v4l2_plane_pix_format members of the returned v4l2_format pointer when passed
through TRY_FMT ioctl.
This ensures that the user doesn't interpret the non-zero fields as some data
passed by the driver, and ensures compliance.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vpe output and capture queues are initially configured to default values in
vpe_open(). A G_FMT before any S_FMTs will result in these values being
populated.
The colorspace and bytesperline parameter of this initial configuration are
incorrect. This breaks compliance when as we get 'TRY_FMT(G_FMT) != G_FMT'.
Fix the initial queue configuration such that it wouldn't need to be fixed by
try_fmt.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The bus_info parameter in v4l2_capabilities expects a 'platform_' prefix. This
wasn't done in the driver and hence was breaking compliance. Update the bus_info
parameter accordingly.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
querycap currently returns V4L2_CAP_VIDEO_M2M as a capability, this should be
V4L2_CAP_VIDEO_M2M_MPLANE instead, as the driver supports multiplanar formats.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The minimum width and height for VPE input/output was kept as 128 pixels. VPE
doesn't have a constraint on the image height, it requires the image width to
be at least 16 bytes.
Change the minimum supported dimensions to 32x32. This allows us to de-interlace
qcif content. A smaller image size than 32x32 didn't make much sense, so stopped
at this.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video_device struct is currently embedded in the driver data struct vpe_dev.
A vpe_dev instance is allocated by the driver, and the memory for the vfd is a
part of this struct.
The v4l2 core, however, manages the removal of the vfd region, through the
video_device's .release() op, which currently is the helper
video_device_release. This causes memory corruption, and leads to issues when
we try to re-insert the vpe module.
Use the video_device_release_empty helper function instead.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VPE has a ctrl parameter which decides how many mem to mem transactions the
active job from the job queue can perform.
The driver's job_ready() made sure that the number of ready source buffers are
sufficient for the job to execute successfully. But it didn't make sure if
there are sufficient ready destination buffers in the capture queue for the
VPE output.
If the time taken by VPE to process a single frame is really slow, then it's
possible that we don't need to imply such a restriction on the dst queue, but
really fast transactions(small resolution, no de-interlacing) may cause us to
hit the condition where we don't have any free buffers for the VPE to write on.
Add the extra check in job_ready() to make sure we have the sufficient amount
of destination buffers.
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add sleep ops to lgdt3304_ops to invoke lgdt3305_sleep() to be called
from dvb_frontend_suspend(). lgdt3305_soft_reset() is called for both
3304 and 3305 devices. soft_reset and sleep touch LGDT3305_GEN_CTRL_3
on 3304 and 3305 devices. Hence, adding sleep to lgdt3304_ops will help
suspend 3304 properly from dvb_frontend_suspend().
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Kconfig entry for "Micronas DRX-J demodulator" defaults to modular
if DVB_FE_CUSTOMISE is set. But that Kconfig symbol was replaced with
MEDIA_SUBDRV_AUTOSELECT as of v3.7. So use the new symbol. And negate
the logic, because MEDIA_SUBDRV_AUTOSELECT's logic is the opposite of
the former logic.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
fix the following warnings:
m88rs2000.c:300:16: warning: symbol 'm88rs2000_setup' was not declared. Should it be static?
m88rs2000.c:318:16: warning: symbol 'm88rs2000_shutdown' was not declared. Should it be static?
m88rs2000.c:328:16: warning: symbol 'fe_reset' was not declared. Should it be static?
m88rs2000.c:366:16: warning: symbol 'fe_trigger' was not declared. Should it be static?
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Correct the initialization values at the start of the function
and use proper variable sizes to prevent overflow.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The generic scancode filtering has questionable value and makes it
impossible to determine from userspace if there is an actual
scancode hw filter present or not.
So revert the generic parts.
Based on a patch from James Hogan <james.hogan@imgtec.com>, but this
version also makes sure that only the valid sysfs files are created
in the first place.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Overloading dev->s_filter to do two different functions (set wakeup filters
and generic hardware filters) makes it impossible to tell what the
hardware actually supports, so create a separate dev->s_wakeup_filter and
make the distinction explicit.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This reverts 18bc174481 and changes
the code at img-ir-nec.c to use the order used by the other NEC decoders.
The original patch ignored the fact that NEC32 scancodes are generated not
only in the NEC raw decoder but also directly in some drivers. Whichever
approach is chosen it should be consistent across drivers and this patch
needs more discussion.
Furthermore, I'm convinced that we have to stop playing games trying to
decipher the "meaning" of NEC scancodes (what's the customer/vendor/address,
which byte is the MSB, etc).
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Coverity CID 1196501: Missing break in switch (MISSING_BREAK)
I introduced that bug recently by commit
96a5b3a869.
As a result, it will flood unintentionally error message to log.
Reported-by: <scan-admin@coverity.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull exynos media updates from Mauro Carvalho Chehab:
"These are the remaining patches I have for the merge windows. It
basically adds a new sensor and adds the needed DT bits for it to
work"
* 'topic/exynos' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] s5p-fimc: Remove reference to outdated macro
[media] s5p-jpeg: Fix broken indentation in jpeg-regs.h
[media] exynos4-is: Add the FIMC-IS ISP capture DMA driver
[media] exynos4-is: Add support for asynchronous subdevices registration
[media] exynos4-is: Add clock provider for the SCLK_CAM clock outputs
[media] exynos4-is: Use external s5k6a3 sensor driver
[media] V4L: s5c73m3: Add device tree support
[media] V4L: Add driver for s5k6a3 image sensor
[media] Documentation: devicetree: Update Samsung FIMC DT binding
[media] Documentation: dt: Add binding documentation for S5C73M3 camera
[media] Documentation: dt: Add binding documentation for S5K6A3 image sensor
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
Pull compat time conversion changes from Peter Anvin:
"Despite the branch name this is really neither an x86 nor an
x32-specific patchset, although it the implementation of the
discussions that followed the x32 security hole a few months ago.
This removes get/put_compat_timespec/val() and replaces them with
compat_get/put_timespec/val() which are savvy as to the current status
of COMPAT_USE_64BIT_TIME.
It removes several unused and/or incorrect/misleading functions (like
compat_put_timeval_convert which doesn't in fact do any conversion)
and also replaces several open-coded implementations what is now
called compat_convert_timespec() with that function"
* 'x86-x32-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compat: Fix sparse address space warnings
compat: Get rid of (get|put)_compat_time(val|spec)
Here's the huge drivers/staging/ update for 3.15-rc1.
Loads of cleanup fixes, a few drivers removed, and some new ones added.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7BqAACgkQMUfUDdst+ykHUwCguJDlvM7/FGb3QQslAuKN5Np4
n2YAoJ3C355mo8Wxr/bJah3Jms4f+a7Q
=4XGY
-----END PGP SIGNATURE-----
Merge tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the huge drivers/staging/ update for 3.15-rc1.
Loads of cleanup fixes, a few drivers removed, and some new ones
added.
All have been in linux-next for a while"
* tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1375 commits)
staging: xillybus: XILLYBUS_PCIE depends on PCI_MSI
staging: xillybus: Added "select CRC32" for XILLYBUS in Kconfig
staging: comedi: poc: remove obsolete driver
staging: unisys: replace kzalloc/kfree with UISMALLOC/UISFREE
staging: octeon-usb: prevent memory corruption
staging: usbip: fix line over 80 characters
staging: usbip: fix quoted string split across lines
Staging: unisys: Remove RETINT macro
Staging: unisys: Remove FAIL macro
Staging: unisys: Remove RETVOID macro
Staging: unisys: Remove RETPTR macro
Staging: unisys: Remove RETBOOL macro
Staging: unisys: Remove FAIL_WPOSTCODE_1 macro
Staging: unisys: Cleanup macros to get rid of goto statements
Staging: unisys: include: Remove unused macros from timskmod.h
staging: dgap: fix the rest of the checkpatch warnings in dgap.c
Staging: bcm: Remove unnecessary parentheses
staging: wlags49_h2: Delete unnecessary braces
staging: wlags49_h2: Do not use assignment in if condition
staging: wlags49_h2: Enclose macro in a do-while loop
...
Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a few
other tiny driver core patches.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7A0wACgkQMUfUDdst+ynJNACfZlY+KNKIhNFt1OOW8rQfSZzy
1PYAnjYuOoly01JlPrpJD5b4TdxaAq71
=GVUg
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and sysfs updates from Greg KH:
"Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a
few other tiny driver core patches.
All have been in linux-next for a while"
* tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (42 commits)
Revert "sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()"
kernfs: cache atomic_write_len in kernfs_open_file
numa: fix NULL pointer access and memory leak in unregister_one_node()
Revert "driver core: synchronize device shutdown"
kernfs: fix off by one error.
kernfs: remove duplicate dir.c at the top dir
x86: align x86 arch with generic CPU modalias handling
cpu: add generic support for CPU feature based module autoloading
sysfs: create bin_attributes under the requested group
driver core: unexport static function create_syslog_header
firmware: use power efficient workqueue for unloading and aborting fw load
firmware: give a protection when map page failed
firmware: google memconsole driver fixes
firmware: fix google/gsmi duplicate efivars_sysfs_init()
drivers/base: delete non-required instances of include <linux/init.h>
kernfs: fix kernfs_node_from_dentry()
ACPI / platform: drop redundant ACPI_HANDLE check
kernfs: fix hash calculation in kernfs_rename_ns()
kernfs: add CONFIG_KERNFS
sysfs, kobject: add sysfs wrapper for kernfs_enable_ns()
...
Add missing m88ts2022 module reference counts as removing that module
is not allowed when it is used by em28xx-dvb module. That same module
was not unregistered correctly, fix it too.
Error cases validated by returning errors from m88ds3103, m88ts2022
and a8293 probe().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The first hunk of this patch got merged wrong, likely due to some
changes at the em28xx resume code. Revert it to reapply it right.
This reverts commit 37571b163c.
Reported-by: Chris Lee <updatelee@gmail.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: stable@vger.kernel.org # Don't apply this patch or 37571b163c
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pointer to device state has been moved to different location during
some change. PCTV 290e LNA function still uses old pointer, carried
over FE priv, and it crash.
Reported-by: Janne Kujanpää <jikuja@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add missing m88ts2022 module reference counts as removing that module
is not allowed when it is used by em28xx-dvb module. That same module
was not unregistered correctly, fix it too.
Error cases validated by returning errors from m88ds3103, m88ts2022
and a8293 probe().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Band switching didn't worked always reliably as there was one
register bit set wrong.
Thanks to Robert Schlabbach for pointing this bug and solution.
Reported-by: Robert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Do not attempt to reload the tuner modules when resuming after a suspend.
This triggers a WARN_ON in kernel/kmod.c:148 __request_module.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=69581.
This has always been wrong, but it was never noticed until the WARN_ON
was added in 3.9.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.9 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I completely forgot to add them when I made this module. Loading this module
without it will taint the kernel, which is not intended.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.12 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The SI4713 select should be I2C_SI4713 and the USB driver needs to depend on
I2C as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
commit 340a30c514 "s2255drv: upgrade to videobuf2" changed the API
used by the s2255 driver, but did not modify the Kconfig statement,
which can lead to build errors when no other driver already uses
VIDEOBUF2_VMALLOC. This patch does the necessary Kconfig change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is request_irq() in init_device(), but the interrupt is not removed
on failure paths. The patch adds proper error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That tuner driver is mainly for DVB API, but there is some V4L2 API
controls for SDR usage. Make driver compile conditional so that V4L2
is not mandatory. Without the V4L2 support driver is build as a DVB
only, without SDR controls.
Fixes following errors reported by kbuild test robot:
ERROR: "v4l2_ctrl_auto_cluster" [drivers/media/tuners/e4000.ko] undefined!
ERROR: "v4l2_ctrl_new_std" [drivers/media/tuners/e4000.ko] undefined!
ERROR: "v4l2_ctrl_handler_init_class" [drivers/media/tuners/e4000.ko] undefined!
ERROR: "v4l2_ctrl_handler_free" [drivers/media/tuners/e4000.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting functions for hardware filter is a bad idea, as it
breaks compilation if:
CONFIG_DVB_USB_AF9035=y
CONFIG_DVB_AF9033=m
Because the PID filter function calls would be hardcoded at
af9035.
The same doesn't happen with af9033_attach() because the
dvb_attach() doesn't hardcode it. Instead, it dynamically
links it at runtime.
However, calling dvb_attach() multiple times is problematic,
as it increments module kref.
So, the better is to pass one parameter for the af9033 module
to fill the hardware filters, and then use it inside af9035.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PID filters are property of af9033 demod. Use PID filters from af9033
driver as it provides those now.
Allow possible dual mode on USB 1.1 mode too as bandwidth could be
just enough when filters are used on both frontends.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement PID filter and export it via symbol.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All error/warnings:
drivers/built-in.o: In function `e4000_set_params':
>> e4000.c:(.text+0x1219a1b): undefined reference to `__umoddi3'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a video capture node for the FIMC-IS ISP IP block. The Exynos4x12
FIMC-IS ISP IP block has 2 DMA interfaces that allow to capture raw
Bayer and YUV data to memory. Currently only the DMA2 output is and
raw Bayer data capture is supported.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for registering external sensor subdevs using
v4l2-async API. The async API is used only for sensor subdevs
and only for booting from DT.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds clock provider so the the SCLK_CAM0/1 output clocks
can be accessed by image sensor devices through the clk API.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes the common fimc-is-sensor driver for image sensors
that are normally controlled by the FIMC-IS firmware. The FIMC-IS
driver now contains only a table of properties specific to each sensor.
The sensor properties required for the ISP's firmware are parsed from
device tree and retrieved from the internal table, which is selected
based on the compatible property of an image sensor.
To use the Exynos4x12 internal ISP the S5K6A3 sensor driver (drivers/
media/i2c/s5k6a3.c) is now required.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the V4L2 asynchronous subdev registration and
device tree support. Common clock API is used to control the
sensor master clock from within the subdev.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds subdev driver for Samsung S5K6A3 raw image sensor.
As it is intended at the moment to be used only with the Exynos
FIMC-IS (camera ISP) subsystem it is pretty minimal subdev driver.
It doesn't do any I2C communication since the sensor is controlled
by the ISP and its own firmware.
This driver, if needed, can be updated in future into a regular
subdev driver where the main CPU communicates with the sensor
directly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In all cases, when the first capture is called, we need to
call the code that unmutes the volume.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The calculated values for the minlen and maxlen fields, which were
rounded to multiples of 2 and clamped to a valid range, were left
unused. Use them in the calculation of the register value rather than
using the raw input minlen and maxlen.
This fixes the following warning with a W=1 build:
drivers/media/rc/img-ir/img-ir-hw.c In function ‘img_ir_free_timing’:
drivers/media/rc/img-ir/img-ir-hw.c +228 :23: warning: variable ‘maxlen’ set but not used [-Wunused-but-set-variable]
drivers/media/rc/img-ir/img-ir-hw.c +228 :15: warning: variable ‘minlen’ set but not used [-Wunused-but-set-variable]
Reported-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The JVC timings included timings intended for the secondary decoder
(which matches messages with no leader), however they were in the wrong
part of the timings structure, repeating s00 and s01 rather than being
in s10 and s11.
Distinct repeat timings can't be properly supported yet for JVC anyway
since the scancode callback cannot determine which decoder matched the
message, so for now remove these timings and don't bother to enable the
secondary decoder.
This fixes the following warnings with W=1:
drivers/media/rc/img-ir/img-ir-jvc.c +76 :3: warning: initialized field overwritten [-Woverride-init]
drivers/media/rc/img-ir/img-ir-jvc.c +76 :3: warning: (near initialization for ‘img_ir_jvc.timings.s00’) [-Woverride-init]
drivers/media/rc/img-ir/img-ir-jvc.c +81 :3: warning: initialized field overwritten [-Woverride-init]
drivers/media/rc/img-ir/img-ir-jvc.c +81 :3: warning: (near initialization for ‘img_ir_jvc.timings.s01’) [-Woverride-init]
Reported-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename some variables.
Change error status checks from (ret < 0) to (ret).
No actual functionality changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That comes possible after driver was converted to kernel I2C model
(I2C binding & proper I2C client with no gate control hack). All
nasty low level I2C routines are now covered by regmap.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Gate control is now implemented by rtl2832 I2C adapter so we do not
need proprietary DVB i2c_gate_ctrl() anymore.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832 driver provides muxed I2C adapters for tuner bus I2C gate
control. Pass those adapters to rtl2832_sdr and e4000 modules in order
to get rid of proprietary DVB .i2c_gate_ctrl() callback use.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We need depend on I2C_MUX as rtl2832 demod used requires it.
All error/warnings:
warning: (DVB_USB_RTL28XXU) selects DVB_RTL2832 which has unmet direct dependencies (MEDIA_SUPPORT && DVB_CORE && I2C && I2C_MUX)
ERROR: "i2c_add_mux_adapter" [drivers/media/dvb-frontends/rtl2832.ko] undefined!
ERROR: "i2c_del_mux_adapter" [drivers/media/dvb-frontends/rtl2832.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement PLL lock control to get PLL lock flag status from tuner
synthesizer.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was 32-bit overflow on VCO frequency calculation which blocks
tuning to 1073 - 1104 MHz. Use 64 bit number in order to avoid VCO
frequency overflow.
After that fix device in question tunes to following range:
60 - 1104 MHz
1250 - 2207 MHz
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement gain and bandwidth controls using v4l2 control framework.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver conversion from proprietary DVB tuner model to more
general I2C driver model.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
rc_map_get() takes a single string literal for the module to load,
so make sure it cannot be used as a format string in the call to
request_module().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename v4l2_format_sdr to v4l2_sdr_format in order to keep it in
line with other formats.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add volatile boolean control to indicate if tuner frequency synthesizer
is locked to requested frequency. That means tuner is able to receive
given frequency. Control is named as "PLL lock", since frequency
synthesizers are based of phase-locked-loop. Maybe more general name
could be wise still?
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modern silicon RF tuners has one or more adjustable filters on
signal path, in order to filter noise from desired radio channel.
Add channel bandwidth control to tell the driver which is radio
channel width we want receive. Filters could be then adjusted by
the driver or hardware, using RF frequency and channel bandwidth
as a base of filter calculations.
On automatic mode (normal mode), bandwidth is calculated from sampling
rate or tuning info got from userspace. That new control gives
possibility to set manual mode and let user have more control for
filters.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The "Renesas Corporation" listed in the copyright notice doesn't exist.
Replace it with "Renesas Electronics Corporation" and update the
copyright years.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Check if index is within bounds _before_ accessing the value.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It was possible that tuner_frequency variable, used for carrier offset
compensation, was uninitialized. That happens when tuner
.get_frequency() callback is not defined.
Currently that case is not possible as only used tuner has this callback.
Coverity CID 1166057: Uninitialized scalar variable (UNINIT)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Coverity CID 1166051: Logically dead code (DEADCODE)
TS clock calculation could be more accurate, but as it is not,
remove those unused clock speeds.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While playing with make coccicheck I noticed this message:
drivers/media/rc/rc-main.c:1245:3-9: preceding lock on line 1238
It was introduced by commit 587d1b06e0 ([media] rc-core: reuse device
numbers) which returns -ENOMEM after a mutex_lock without first
unlocking it when there are no more device numbers left. The added code
doesn't depend on the device lock, so move it before the lock is taken.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Static checkers complain about the inconsistent NULL check here.
There is an unchecked dereference of "input->fe" in the call to
tuner_attach_tda18271() and there is a second unchecked dereference a
couple lines later when we do:
input->fe2->tuner_priv = input->fe->tuner_priv;
But actually "intput->fe" can't be NULL because if demod_attach_drxk()
fails to allocate it, then we would have return an error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ARRAY_SIZE(buf) (8 elements) was intended instead of sizeof(buf) (16
bytes). But this is just a sanity check and the callers always pass
valid values so this doesn't cause a problem.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an img-ir module for decoding the Sanyo infrared protocol.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an img-ir module for decoding the Sharp infrared protocol.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an img-ir module for decoding the Sony infrared protocol.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an img-ir module for decoding the JVC infrared protocol.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an img-ir module for decoding the NEC and extended NEC infrared
protocols.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add ImgTec IR decoder driver to the build system.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add remote control input driver for the ImgTec Infrared block hardware
decoder, which is set up with timings for a specific protocol and
supports mask/value filtering and wake events.
The hardware decoder timing values, raw data to scan code conversion
function and scan code filter to raw data filter conversion function
will be provided in separate files for each protocol which this part of
the driver can use. The new generic scan code filter interface is made
use of to reduce interrupts and control wake events.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add raw IR remote control input driver for the ImgTec Infrared decoder
block's raw edge interrupts. Generic software protocol decoders are used
to allow multiple protocols to be supported at a time, including those
not supported by the hardware decoder.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add base driver for the ImgTec Infrared decoder block. The driver is
split into separate components for raw (software) decode and hardware
decoder which are in following commits.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When either of the normal or wakeup filter protocols are changed,
refresh the corresponding scancode filter, i.e. try and set the same
scancode filter with the new protocol. If that fails clear the filter
instead.
If no protocol was selected the filter is just cleared, and if no
s_filter callback exists the filter is left unmodified.
Similarly clear the filter mask when the filter is set if no protocol is
currently selected.
This simplifies driver code which no longer has to explicitly worry
about modifying the filter on a protocol change. This also allows the
change_wakeup_protocol callback to be omitted entirely if there is only
a single available wakeup protocol at a time, since selecting no
protocol will automatically clear the wakeup filter, disabling wakeup.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a wakeup_protocols sysfs file which controls the new
rc_dev::enabled_protocols[RC_FILTER_WAKEUP], which is the mask of
protocols that are used for the wakeup filter.
A new RC driver callback change_wakeup_protocol() is called to change
the wakeup protocol mask.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Only a single allowed and enabled protocol mask currently exists in
struct rc_dev, however to support a separate wakeup filter protocol two
of each are needed, ideally as an array.
Therefore make both rc_dev::allowed_protos and rc_dev::enabled_protocols
arrays, update all users to reference the first element
(RC_FILTER_NORMAL), and add a couple more helper functions for drivers
to use for setting the allowed and enabled wakeup protocols.
We also rename allowed_protos to allowed_protocols while we're at it,
which is more consistent with enabled_protocols.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add generic scancode filtering of RC input events, and fall back to
permitting any RC_FILTER_NORMAL scancode filter to be set if no s_filter
callback exists. This allows raw IR decoder events to be filtered, and
potentially allows hardware decoders to set looser filters and rely on
generic code to filter out the corner cases.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On certain motherboards (mainly Intel NUC series) bios keeps the
Nuvoton CIR device disabled at boot.
This patch adds a call to kernel PNP layer to activate the device if it
is not already activated. This will improve the chances of the PNP probe
actually succeeding on Intel NUC platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DViCO FusionHDTV7 device that use au0828 can fail to communicate with
xc5000 using i2c interface because of high i2c clock speed - i2c clock
stretching bug. It causes to fail xc5000 firmware loading normally at
the current driver.
Already this problem fixed as changing to low i2c clock speed at
HVR-950q device, also DViCO FusionHDTV7 device can solve it as using low
i2c clock speed - 20KHz.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Propagate errors returned by drivers from the s_filter callback back to
userland when updating scancode filters. This allows userland to see
when the filter couldn't be updated, usually because it's not a valid
filter for the hardware.
Previously the filter was being updated conditionally on success of
s_filter, but the write always reported success back to userland.
Reported-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a device id to support for PX-S1UD (PLEX ISDB-T usb dongle) which
has sms2270.
Signed-off-by: Satoshi Nagahama <sattnag@aim.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since the introduction of the new OMAP DSS DVI connector driver in
commit 348077b154 ("OMAPDSS: Add new DVI
Connector driver"), DVI outputs report a new display type of
OMAP_DISPLAY_TYPE_DVI instead of OMAP_DISPLAY_TYPE_DPI. Handle the new
type in the IRQ handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
New board addition. No other changes.
[m.chehab@samsung.com: rebase patch and fix whitespace mangling]
Signed-off-by: Pojar George <geoubuntu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These chips makes use of the media_entity in the v4l2_subdev struct
and is therefor dependent of the MEDIA_CONTROLLER config.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
try_fmt should just set field to NONE and not return an error if
a different field was passed.
buf_prepare should check if the field passed in from userspace has a
supported field value. At the moment only NONE is supported and ANY
is mapped to NONE.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- Set the sequence counters correctly.
- Copy timestamps, timecode, relevant buffer flags and field from
the received buffer to the outgoing buffer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
To keep the vb2 buffer administration in balance stop_streaming() must
return any pending buffers to the vb2 framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no reason why we shouldn't enable this here.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This resolves an issue raised by v4l2-compliance: if the given format does
not exist, then pick a default format.
While there is an exception regarding this for TV capture drivers, this
m2m driver should do the right thing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The default of 1 second is a bit painful, switch to a 25 Hz framerate.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no any reason to use comma here.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7180 has a low power mode in which the analog and the digital processing
section are shut down. Implement the s_power callback to let bridge drivers put
the part into low power mode when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for async device registration to the adv7180 driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The proper way to handle IRQs that need to be able to sleep in their IRQ handler
is to use a threaded IRQ.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The device driver core already prints out a very similar message when a driver
fails to probe. No need to print one in the driver itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The device can't possibly be registered at this point, so no need to to call
v4l2_device_unregister_subdev().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Make sure to free the control handler when the device is removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The mutex is used in the subdev callbacks, so unregister the subdev before the
mutex is destroyed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Support this ioctl as part of the v4l2 core. Use the new ioctl
name and struct v4l2_edid type in the existing core code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The wrong ioctl numbers were used due to a copy-and-paste error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.7 and up
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the driver for the LM3646, dual LED Flash driver.
The LM3646 has two 1.5A sync. boost converter with dual white current source.
It is controlled via an I2C compatible interface.
Each flash brightness, torch brightness and enable/disable can be controlled.
Under voltage, input voltage monitor and thermal threshhold Faults are added.
Please refer the datasheet http://www.ti.com/lit/ds/snvs962/snvs962.pdf
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If we have no pdata defined and driver fails to register we leak memory.
Converting to devm_kzalloc prevents this to happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Let's keep the style for all comments in the code, namely using small letters
whenever it's possible.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no need to keep the FSF address inside each file. Moreover, it might
change in future which will make this one obsolete.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Empty port nodes are allowed but currently unsupported as the
v4l2_of_get_next_endpoint() function assumes that all port nodes have at
least an endpoint. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for MBUS YUV10 BT656 and BT601 formats at rcar driver.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes memory leak introduced by
commit 47d8c881c3.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set permissions on the debug module parameter to make it appear in sysfs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This code is correct but the indenting is wrong and triggers a static
checker warning "add curly braces?".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
interruptible_sleep_on is racy and going away. In the arv driver that
race has probably never caused problems since it would require a whole
video frame to be captured before the read function has a chance to
go to sleep, but using wait_event_interruptible lets us kill off the
old interface. In order to do this, we have to slightly adapt the
meaning of the ar->start_capture field to distinguish between not having
started a frame and having completed it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If NO_DMA=y:
warning: (VIDEO_DM6446_CCDC && VIDEO_DM355_CCDC && VIDEO_DM365_ISIF && VIDEO_OMAP2_VOUT && VIDEO_SH_VOU && VIDEO_VIU && VIDEO_TIMBERDALE && VIDEO_MX1 && VIDEO_OMAP1) selects VIDEOBUF_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/built-in.o: In function `videobuf_vm_close':
videobuf-dma-contig.c:(.text+0x407aa0): undefined reference to `videobuf_queue_cancel'
drivers/built-in.o: In function `__videobuf_dc_alloc':
videobuf-dma-contig.c:(.text+0x407ba2): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `__videobuf_mmap_mapper':
videobuf-dma-contig.c:(.text+0x407d44): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `free_buffer':
sh_vou.c:(.text+0x41f73a): undefined reference to `videobuf_waiton'
drivers/built-in.o: In function `sh_vou_poll':
sh_vou.c:(.text+0x41f884): undefined reference to `videobuf_poll_stream'
drivers/built-in.o: In function `sh_vou_buf_prepare':
sh_vou.c:(.text+0x41fdf6): undefined reference to `videobuf_iolock'
drivers/built-in.o: In function `sh_vou_reqbufs':
sh_vou.c:(.text+0x4203b0): undefined reference to `videobuf_reqbufs'
drivers/built-in.o: In function `sh_vou_querybuf':
sh_vou.c:(.text+0x42040a): undefined reference to `videobuf_querybuf'
drivers/built-in.o: In function `sh_vou_qbuf':
sh_vou.c:(.text+0x42045e): undefined reference to `videobuf_qbuf'
drivers/built-in.o: In function `sh_vou_dqbuf':
sh_vou.c:(.text+0x4204c2): undefined reference to `videobuf_dqbuf'
drivers/built-in.o: In function `sh_vou_streamon':
sh_vou.c:(.text+0x420572): undefined reference to `videobuf_streamon'
drivers/built-in.o: In function `sh_vou_streamoff':
sh_vou.c:(.text+0x4205d2): undefined reference to `videobuf_streamoff'
drivers/built-in.o: In function `sh_vou_mmap':
sh_vou.c:(.text+0x420c46): undefined reference to `videobuf_mmap_mapper'
VIDEO_SH_VOU selects VIDEOBUF_DMA_CONTIG, which bypasses its dependency on
HAS_DMA. Make VIDEO_SH_VOU depend on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
tree: git://linuxtv.org/media_tree.git master
head: a3550ea665
commit: a3550ea665 [499/499] [media] usbtv: split core and video implementation
reproduce: make C=1 CF=-D__CHECK_ENDIAN__
sparse warnings: (new ones prefixed by >>)
>> drivers/media/usb/usbtv/usbtv-core.c:119:22: sparse: symbol 'usbtv_id_table' was not declared. Should it be static?
>> drivers/media/usb/usbtv/usbtv-core.c:129:19: sparse: symbol 'usbtv_usb_driver' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are two troubles there:
1) the bit error measure were not accumulating;
2) it was missing the bit count.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function 'ctrl_get_qam_sig_quality':
drivers/media/dvb-frontends/drx39xyj/drxj.c:9468:6: warning: variable 'ber_cnt' set but not used [-Wunused-but-set-variable]
u32 ber_cnt = 0; /* BER count */
^
By reading the comment, it is said that BER should be calculated as:
qam_pre_rs_ber = frac_times1e6( ber_cnt, rs_bit_cnt );
Also, it makes sense to take the mantissa into account, so fix the
code to do what's commented.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that everything is set, let's enable DVBv5 stats, for
applications that support it.
DVBv3 apps will still work.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just assuming that the min resolution is 1E-6,
pass both bit error and bit counts for userspace to calculate
BER. The same applies for PER, for 8VSB. It is not clear how
to get the packet count for QAM. So, for now, don't expose PER
for QAM.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert the stats internally to use DVBv5. For now, it will keep
showing everything via DVBv3 API only, as the .len value were
not initialized.
That allows testing if the new stats code didn't break anything.
A latter patch will add the final bits for the DVBv5 stats to
fully work.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We'll need to use this function. Restore it from the
git history.
This function will be used on the next patch.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
State is already used on other places for the state struct.
Don't use it here, to avoid troubles with latter patches.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported when compiled with W=1:
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘ctrl_set_channel’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:10340:26: warning: variable ‘common_attr’ set but not used [-Wunused-but-set-variable]
struct drx_common_attr *common_attr = NULL;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:10336:6: warning: variable ‘intermediate_freq’ set but not used [-Wunused-but-set-variable]
s32 intermediate_freq = 0;
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is currently not used. However, it was meant to
be called at device release. So, add it there.
While here, remove the bad check, as reported by Dan, as
smatch warning:
drivers/media/dvb-frontends/drx39xyj/drxj.c:20041 drxj_close() warn: variable dereferenced before check 'demod' (see line 20036)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are large chunks of code at drx-j that aren't used. Most
of them are due to analog TV support. Well, just enabling them
won't make analog support work, as devices with DRX and analog
support requires an extra chip (avf4910).
We don't have drivers for it, nor the current device that uses
this frontend has support for analog TV.
So, let's just get rid of this code. If latter needed, this
patch can easily be reverted from git history.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by the kbuild test robot <fengguang.wu@intel.com>:
drivers/built-in.o: In function `em28xx_dvb_init':
em28xx-dvb.c:(.text+0x876f2c): undefined reference to `drx39xxj_attach'
That happens when CONFIG_VIDEO_EM28XX_DVB is selected, and neither
CONFIG_MEDIA_SUBDRV_AUTOSELECT or DVB_DRX39XYJ is selected.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes the following warnings:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1679:65: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1679:71: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1681:52: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1681:58: warning: Using plain integer as NULL pointer
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No functional changes, but removes a duplicate check, if
!state->type_A.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix sparse warning:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1039:16: sparse: symbol 'drxj_default_aud_data_g' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Simplify the logic a little by removing one level of identation.
Also, it only makes sense to print something if the .fini callback
is actually doing something.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We can't free struct em28xx while one of the extensions is still
using it.
So, add a kref() to control it, freeing it only after the
extensions fini calls.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function never checked if width and height are correct. Add such
a check so the v4l2-compliance tool returns OK again for vivi.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If start_streaming fails then any queued buffers must be given back
to the vb2 core.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't call buf_finish unless we know that the buffer is in a valid state.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If you request buffers, then queue buffers and then call STREAMOFF
those buffers are not returned to their dequeued state because streamoff
will just return if q->streaming was 0.
This means that afterwards you can never QBUF that same buffer again unless
you do STREAMON, REQBUFS or close the filehandle first.
It is clear that if you do STREAMOFF even if no STREAMON was called before,
you still want to have all buffers returned to their proper dequeued state.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to oops for this, WARN_ON is good enough.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If __reqbufs was called then existing buffers are freed. However, if that
happens without ever having started STREAMON, but if buffers have been queued,
then the buf_finish op is never called.
Add a call to __vb2_queue_cancel in __reqbufs so that these buffers are
cleaned up there as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In commit 02f142ecd2 support was added to
start_streaming to return -ENOBUFS if insufficient buffers were queued
for the DMA engine to start. The vb2 core would attempt calling
start_streaming again if another buffer would be queued up.
Later analysis uncovered problems with the queue management if start_streaming
would return an error: the buffers are enqueued to the driver before the
start_streaming op is called, so after an error they are never returned to
the vb2 core. The solution for this is to let the driver return them to
the vb2 core in case of an error while starting the DMA engine. However,
in the case of -ENOBUFS that would be weird: it is not a real error, it
just says that more buffers are needed. Requiring start_streaming to give
them back only to have them requeued again the next time the application
calls QBUF is inefficient.
This patch changes this mechanism: it adds a 'min_buffers_needed' field
to vb2_queue that drivers can set with the minimum number of buffers
required to start the DMA engine. The start_streaming op is only called
if enough buffers are queued. The -ENOBUFS handling has been dropped in
favor of this new method.
Drivers are expected to return buffers back to vb2 core with state QUEUED
if start_streaming would return an error. The vb2 core checks for this
and produces a warning if that didn't happen and it will forcefully
reclaim such buffers to ensure that the internal vb2 core state remains
consistent and all buffer-related resources have been correctly freed
and all op calls have been balanced.
__reqbufs() has been updated to check that at least min_buffers_needed
buffers could be allocated. If fewer buffers were allocated then __reqbufs
will free what was allocated and return -ENOMEM. Based on a suggestion from
Pawel Osciak.
__create_bufs() doesn't do that check, since the use of __create_bufs
assumes some advance scenario where the user might want more control.
Instead streamon will check if enough buffers were allocated to prevent
streaming with fewer than the minimum required number of buffers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
__vb2_queue_free() would init the queued_list at all times, even if
q->num_buffers > 0. This should only happen if num_buffers == 0.
This situation can happen if a CREATE_BUFFERS call couldn't allocate
enough buffers and had to free those it did manage to allocate before
returning an error.
While we're at it: __vb2_queue_alloc() returns the number of buffers
allocated, not an error code. So stick the result in allocated_buffers
instead of ret as that's very confusing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'queued_count' is a bit vague since it is not clear to which queue it
refers to: the vb2 internal list of buffers or the driver-owned list
of buffers.
Rename to make it explicit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ensure that these ops are properly balanced.
There are two scenarios:
1) for MMAP buf_init is called when the buffers are created and buf_cleanup
must be called when the queue is finally freed. This scenario was always
working.
2) for USERPTR and DMABUF it is more complicated. When a buffer is queued
the code checks if all planes of this buffer have been acquired before.
If that's the case, then only buf_prepare has to be called. Otherwise
buf_cleanup needs to be called if the buffer was acquired before, then,
once all changed planes have been (re)acquired, buf_init has to be
called followed by buf_prepare. Should buf_prepare fail, then buf_cleanup
must be called on the newly acquired planes to release them in.
Finally, in __vb2_queue_free we have to check if the buffer was actually
acquired before calling buf_cleanup. While that it always true for MMAP
mode, it is not necessarily true for the other modes. E.g. if you just
call REQBUFS and close the file handle, then buffers were never queued and
so no buf_init was ever called.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If a queue was canceled, then the buf_finish op was never called for the
pending buffers. So add this call to queue_cancel. Before calling buf_finish
set the buffer state to PREPARED, which is the correct state. That way the
states DONE and ERROR will only be seen in buf_finish if streaming is in
progress.
Since buf_finish can now be called from non-streaming state we need to
adapt the handful of drivers that actually need to know this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no point in trying to decompress a captured frame unless
the buffer state is OK. It won't be used in any other state, and
in fact the contents of the buffer might well be corrupt.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The buf_finish op should always work, so change the return type to void.
Update the few drivers that use it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When a vb2_queue is freed check if all the mem_ops and queue ops were balanced.
So the number of calls to e.g. buf_finish has to match the number of calls to
buf_prepare, etc.
This code is only enabled if CONFIG_VIDEO_ADV_DEBUG is set.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix an incorrect test in vb2_internal_qbuf() where only DEQUEUED buffers
are allowed. But PREPARED buffers are also OK.
Introduced by commit 4138111a27
("vb2: simplify qbuf/prepare_buf by removing callback").
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 88e268702b ("vb2: Improve file I/O
emulation to handle buffers in any order") broke read/write support if
the size of the buffer being read/written is less than the size of the
image.
When the commit was tested originally I used qv4l2, which calls read()
with exactly the size of the image. But if you try 'cat /dev/video0'
then it will fail and typically hang after reading two buffers.
This patch fixes the behavior by adding a new cur_index field that
contains the index of the field currently being filled/read, or it
is num_buffers in which case a new buffer needs to be dequeued.
The old index field has been renamed to initial_index in order to be
a bit more descriptive.
This has been tested with both read and write.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds a test preventing streamon() if there is no buffer
ready.
Without this patch, a user could call streamon() before
preparing any buffer. This leads to a situation where if he calls
close() before calling streamoff() the device is kept streaming.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds a new struct of_endpoint which is then embedded in struct
v4l2_of_endpoint and contains the endpoint properties that are not V4L2
(or even media) specific: the port number, endpoint id, local device tree
node and remote endpoint phandle. of_graph_parse_endpoint parses those
properties and is used by v4l2_of_parse_endpoint, which just adds the
V4L2 MBUS information to the containing v4l2_of_endpoint structure.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch moves the parsing helpers used to parse connected graphs
in the device tree, like the video interface bindings documented in
Documentation/devicetree/bindings/media/video-interfaces.txt, from
drivers/media/v4l2-core/v4l2-of.c into drivers/of/base.c.
This allows to reuse the same parser code from outside the V4L2
framework, most importantly from display drivers.
The functions v4l2_of_get_next_endpoint, v4l2_of_get_remote_port,
and v4l2_of_get_remote_port_parent are moved. They are renamed to
of_graph_get_next_endpoint, of_graph_get_remote_port, and
of_graph_get_remote_port_parent, respectively.
Since there are not that many current users yet, switch all of
them to the new functions right away.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Use the correct name in the comment describing function
omap3isp_module_sync_is_stopping().
isp_isr() never returned IRQ_NONE, remove the comment saying so.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch renames the variable in the description to match it
appropriately to function definition.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes the description of members which does not exists for
ispccdc_lsc structure.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add bayer 8-bit GUIDs to uvcvideo and associated them with the
corresponding V4L2 pixel formats.
Signed-off-by: Edgar Thier <info@edgarthier.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The UVC specification uses alternate setting selection to notify devices
of stream start/stop. This breaks when using bulk-based devices, as the
video streaming interface has a single alternate setting in that case,
making video stream start and video stream stop events to appear
identical to the device. Bulk-based devices are thus not well supported
by UVC.
The webcam built in the Asus Zenbook UX302LA ignores the set interface
request and will keep the video stream enabled when the driver tries to
stop it. If USB autosuspend is enabled the device will then be suspended
and will crash, requiring a cold reboot.
USB trace capture showed that Windows sends a CLEAR_FEATURE(HALT)
request to the bulk endpoint when stopping the stream instead of
selecting alternate setting 0. The camera then behaves correctly, and
thus seems to require that behaviour.
Replace selection of alternate setting 0 with clearing of the endpoint
halt feature at video stream stop for bulk-based devices. Let's refrain
from blaming Microsoft this time, as it's not clear whether this
Windows-specific but USB-compliant behaviour was specifically developed
to handle bulkd-based UVC devices, or if the camera just took advantage
of it.
CC: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Copy the flags containing the timestamp source from source buffer flags to
the destination buffer flags on memory-to-memory devices. This is analogous
to copying the timestamp field from source to destination.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The timestamp and timecode fields were copied from destination to source,
not the other way around as they should. Fix it.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The UVC device provided timestamps are taken from the clock once the
exposure of the frame has begun, not when the reception of the frame would
have been finished as almost anywhere else. Show this to the user space by
using V4L2_BUF_FLAG_TSTAMP_SRC_SOE buffer flag.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For COPY timestamps, buffer timestamp source flags will traverse the queue
untouched.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some devices do not produce timestamps that correspond to the end of the
frame. The user space should be informed on the matter. This patch achieves
that by adding buffer flags (and a mask) for timestamp sources since more
possible timestamping points are expected than just two.
A three-bit mask is defined (V4L2_BUF_FLAG_TSTAMP_SRC_MASK) and two of the
eight possible values is are defined V4L2_BUF_FLAG_TSTAMP_SRC_EOF for end of
frame (value zero) V4L2_BUF_FLAG_TSTAMP_SRC_SOE for start of exposure (next
value).
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Kamil Debski <k.debski@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mask out other bits when comparing timestamp types.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The timestamp_type field used to contain only the timestamp type. Soon it
will be used for timestamp source flags as well. Rename the field
accordingly.
[m.chehab@samsung.com: do the change also to drivers/staging/media and at s2255]
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When sending a buffer to a video output device some of the fields need
to be copied so they arrive in the driver. These are the KEY/P/BFRAME
flags and the TIMECODE flag, and, if that flag is set, the timecode field
itself.
There are a number of functions involved in this: the __fill_vb2_buffer()
is called while preparing a buffer. For output buffers the buffer contains
the video data, so any meta data associated with that (KEY/P/BFRAME and
the field information) should be stored at that point.
The timecode, timecode flag and timestamp information is not part of that,
that information will have to be set when vb2_internal_qbuf() is called to
actually queue the buffer to the driver. Usually VIDIOC_QBUF will do the
prepare as well, but you can call PREPARE_BUF first and only later VIDIOC_QBUF.
You most likely will want to set the timestamp and timecode when you actually
queue the buffer, not when you prepare it.
Finally, in buf_prepare() make sure the timestamp and sequence fields are
actually cleared so that when you do a QUERYBUF of a prepared-but-not-yet-queued
buffer you will not see stale timestamp/sequence data.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modern silicon RF tuners used nowadays has many controllable gain
stages on signal path. Usually, but not always, there is at least
3 gain stages. Also on some cases there could be multiple gain
stages within the ones specified here. However, I think that having
these three controllable gain stages offers enough fine-tuning for
real use cases.
1) LNA gain. That is first gain just after antenna input.
2) Mixer gain. It is located quite middle of the signal path, where
RF signal is down-converted to IF/BB.
3) IF gain. That is last gain in order to adjust output signal level
to optimal level for receiving party (usually demodulator ADC).
Each gain stage could be set rather often both manual or automatic
(AGC) mode. Due to that add separate controls for controlling
operation mode.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Delay possible I2C gate close a little bit in order to see if there
is next message coming to tuner in a sequence.
Also, export private muxed I2C adapter. That is aimed only for SDR
extension module as SDR belongs to same RTL2832 physical I2C bus (it
is physically property of RTL2832, whilst it is own kernel module).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was a deadlock between master I2C adapter and muxed I2C
adapter. Implement two I2C muxed I2C adapters and leave master
alone, just only for offering I2C adapter for these mux adapters.
Reported-by: Luis Alves <ljalvs@gmail.com>
Reported-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832 provides gated / repeater I2C adapter for tuner.
Implement it as a muxed I2C adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of those were reported by checkpatch.pl...
debug module parameter is not used anywhere so remove it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All used tuners has get_if_frequency() callback and that parameter
is not needed and will not needed as all upcoming tuner drivers
should implement get_if_frequency().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Disable IR interrupts in order to avoid SDR sample loss.
IR interrupts causes some extra load for device and it seems
be one reason to loss samples when sampling rate is high.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is now new tuner types which are not handled on that switch-case.
Print error if unknown tuner type is meet.
drivers/media/tuners/tuner-xc2028.c: In function ‘generic_set_freq’:
drivers/media/tuners/tuner-xc2028.c:1037:2: warning: enumeration value ‘V4L2_TUNER_ADC’ not handled in switch [-Wswitch]
switch (new_type) {
^
drivers/media/tuners/tuner-xc2028.c:1037:2: warning: enumeration value ‘V4L2_TUNER_RF’ not handled in switch [-Wswitch]
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modulator ioctls could be enabled mistakenly for non-radio devices.
Currently those ioctls are only valid for radio. Fix it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Enable stream format (FMT) IOCTLs for SDR use. These are used for negotiate
used data stream format.
Reorganise some some IOCTL selection logic.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add new V4L2 stream format definition, V4L2_BUF_TYPE_SDR_CAPTURE,
for SDR receiver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Define tuner types V4L2_TUNER_ADC and V4L2_TUNER_RF for SDR usage.
ADC is used for setting sampling rate (sampling frequency) to SDR
device.
Another tuner type, named as V4L2_TUNER_RF, is possible RF tuner.
Is is used to down-convert RF frequency to range ADC could sample.
Having RF tuner is optional, whilst in practice it is almost always
there.
Also add checks to VIDIOC_G_FREQUENCY, VIDIOC_S_FREQUENCY and
VIDIOC_ENUM_FREQ_BANDS only allow these two tuner types when device
type is SDR (VFL_TYPE_SDR). For VIDIOC_G_FREQUENCY we do not check
tuner type, instead override type with V4L2_TUNER_ADC in every
case (requested by Hans in order to keep functionality in line with
existing tuners and existing API does not specify it).
Prohibit VIDIOC_S_HW_FREQ_SEEK explicitly when device type is SDR,
as device cannot do hardware seek without a hardware demodulator.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add new V4L device type VFL_TYPE_SDR for Software Defined Radio.
It is registered as /dev/swradio0 (/dev/sdr0 was already reserved).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This device has a led at bit 7 of GPIO reg. 0x80 to indicate
when a DVB capture is happening.
Add support for it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This device is close to Kworld UB435-Q, but it uses a different
tuner. Add support for it.
Tested with both 8VSB and 256QAM modulations.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
tda18272 is programmed just like tda18212, but it also
supports ClearQAM and ATSC.
Add support for them. Tested with a Kworld UB435-Q on both
8VSB and 256QAM modes.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently, there's just one device using this frontend: PCTV 80e,
and it works on serial mode.
Change the default here to serial mode. If we add more devices,
then this option should be set via config structure.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The cfg_mpeg_output has more fields than what it is initialized
when the code is called. Be sure to initialize everything before
use, in order to avoid random behaviors.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just like the windows driver, disable OOB after setting the driver
version.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DJH_DEBUG only code path in drxbsp_i2c_write_read() dereferences
w_dev_addr and subsequently w_dev_addr->user_data->i2c which results
in failure during boot. This patch fixes the null pointer derefence
bug as well as the following compile errors:
LD arch/x86/built-in.o
CC drivers/media/dvb-frontends/drx39xyj/drxj.o
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxbsp_i2c_write_read’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:25: error: redeclaration of ‘state’ with no linkage
struct drx39xxj_state *state = w_dev_addr->user_data;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1512:25: note: previous declaration of ‘state’ was here
struct drx39xxj_state *state;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:2: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
struct drx39xxj_state *state = w_dev_addr->user_data;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1560:17: error: redeclaration of ‘msg’ with no linkage
struct i2c_msg msg[2] = {
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1513:17: note: previous declaration of ‘msg’ was here
struct i2c_msg msg[2];
^
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mimic what windows driver does here: it writes 0x07 to
SIO_CC_SOFT_RST__A, instead of just 0x03.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As drxj_close puts the device in powerdown, we need to power it up
properly at drxj_open.
This is the behavior noticed at the Windows driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are no other I2C masters here. Also, the Windows driver uses
this mode (and both drxd and drxk Kernel drivers). So, switch
to it.
That helps to compare the logs between the Linux driver and the
Windows one.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just disabling the LNA every time, allow to control it from
userspace.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On several places, the I2C functions are just wrappers to others.
Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This struct contains the first abstraction layer for the I2C
access routines. Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file contains an abstract layer for the I2C transfer
functions. Get rid of it, merging it at drxj. This will allow
to remove another abstraction layer there, making the code
easier to read, and removing the functions that just return
-EIO.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reorder functions and data at drx_dap_fasi.c, in order to avoid
having function prototypes.
This is in preparation to merge this code inside drxj, removing
some duplicated bits there, and getting rid of yet another
abstraction layer.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is not used anywere. Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
QAM/256 currently doesn't work, as the code is only called if
channel->mirror is DRX_MIRROR_AUTO, but a prevous if prevents
this condition to happen.
While here, returns -EINVAL to not supported QAM modes and
simplify the code, reducing the number of indents.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Those struct data aren't used anymore. Get rid of them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Checking if a time is after another one can have issues, as
times are generally u32 wide.
Use the proper macros for that at scu_command().
It should be noticed that other places also use jiffies
calculus on an improper way. This should be fixed too,
but the logic there is more complex. So, let's do it in
separate patches.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modulation and other parameters might have changed. So, better
to call ctrl_set_standard() even if the device is already
powered.
That helps to put the device into a sane state, if something
got wrong on a previous set_frontend call.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When switching from one video standard to another one,
power_down_vsb is called twice. Well, as the device is already
in power_down mode, the second call always fail. This causes that
any subsequent frontend set to fail as well:
[145074.501243] drx39xyj:power_down_vsb: called
[145089.195396] drx39xyj:power_down_vsb: error -5
[145089.195404] drx39xyj:ctrl_set_standard: error -5
[145089.195417] drx39xyj:drx39xxj_set_frontend: Failed to set standard! result=fffffffb
[145089.195470] drx39xyj:ctrl_sig_quality: error -5
[145089.195473] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145089.195475] drx39xyj:ctrl_sig_quality: error -5
[145089.195477] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145089.195479] drx39xyj:ctrl_sig_quality: error -5
[145089.195480] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145089.195482] drx39xyj:ctrl_sig_quality: error -5
[145089.195484] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145089.195498] drx39xyj:ctrl_sig_quality: error -5
[145089.195500] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145089.195502] drx39xyj:ctrl_sig_quality: error -5
[145089.195503] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145089.195505] drx39xyj:ctrl_sig_quality: error -5
[145089.195506] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145089.195508] drx39xyj:ctrl_sig_quality: error -5
[145089.195510] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145090.196291] drx39xyj:drx39xxj_read_status: drx39xxj: could not get lock status!
[145090.196508] drx39xyj:ctrl_sig_quality: error -5
[145090.196511] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145090.196514] drx39xyj:ctrl_sig_quality: error -5
[145090.196515] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145090.196518] drx39xyj:ctrl_sig_quality: error -5
[145090.196519] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145090.196522] drx39xyj:ctrl_sig_quality: error -5
[145090.196523] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145090.196553] drx39xyj:ctrl_sig_quality: error -5
[145090.196554] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145090.196557] drx39xyj:ctrl_sig_quality: error -5
[145090.196558] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145090.196560] drx39xyj:ctrl_sig_quality: error -5
[145090.196562] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145090.196564] drx39xyj:ctrl_sig_quality: error -5
[145090.196565] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145091.119265] drx39xyj:ctrl_sig_quality: error -5
[145091.119271] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145091.119274] drx39xyj:ctrl_sig_quality: error -5
[145091.119276] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145091.119278] drx39xyj:ctrl_sig_quality: error -5
[145091.119280] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145091.119282] drx39xyj:ctrl_sig_quality: error -5
[145091.119283] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just hardcoding an IF value of 5MHz, use the one
provided by the tuner, with can be different for QAM and
VSB.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Those functions will never be used with Linux DVB binding.
Get rid of them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file does an ugly binding between drxj and DVB frontend.
Remove most of the functions there. We still need to get rid of
get_frequency and set_frequency, but such patch is a little more
complex, as it should also remove some previous tuner bindings.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to avoid warnings and to remove dead code, remove
the functions that don't make sense to happen, while commenting
the others that might still be useful some day.
That reduced a lot the text size:
Before:
text data bss dec hex filename
58419 2916 4 61339 ef9b drivers/media/dvb-frontends/drx39xyj/drx39xyj.ko
After:
text data bss dec hex filename
78331 2916 4 81251 13d63 drivers/media/dvb-frontends/drx39xyj/drx39xyj.ko
Without any functional changes.
It could be make sense latter to remove those drivers or to
move them into an analog-specific part of the driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With this change, we finally got rid of all abstraction
layers on this driver.
This patch also fixes the LNA GPIO settings, as the original
code were using a wrong control name for it.
This patch exposes the several functions that aren't used.
Some of them are related to analog demod that might be
used some day, but others will likely never be needed, as
they don't fit on Linux media APIs.
Latter patches will clean up this mess.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While drxj is already too big, moving the code there will
make easier to get rid of the drxj_ctrl function.
It will also help to detect and remove the unused functions,
helping to remove lots of dead code there.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Get rid of drx_open and drx_close, as those are just wrapper
functions to drxj_open/drxj_close.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is used only as an abstraction layer to call the
two firmware functions. Remove it.
As a bonus, the drx_ctrl_function is now unused and can be
removed.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove the duplicated firmware upload code that was commented
inside drxj.c.
This code is not used, and will not work anyway, as it doesn't
download the firmware from userspace.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The version is initialized with zero at drx_driver.c. Keep it,
in order to avoid the risk of causing any regression.
While here, remove the drx_driver.h from drxj, as this is not
required there.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file contains just the firmware load code, that it is also
somewhat duplicated at drxj.c.
Move the code into there. Latter patches will remove the
duplicated code.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to prepare to get rid of drx_driver.c, prepend all functions
there with drx_.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is mostly CodingStyle fixes and improvements.
No functional changes.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ClearQAM is currently not working. Add support for it too.
Unlikely other ATSC tuners, though, this device will not
auto-detect between ATSC and ClearQAM. So, the delivery
system should be properly set.
Also, this frontend seems to also support DVB-C annex A/C. Add
experimental support for them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Without this fixup, the DRX-J will not be properly initialized,
loosing several PIDs.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of handling endiannes with its own internal way, use the
already existing macros.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several drx-j code there that are never used, as
they don't even fit into Linux DVB subystem model.
Remove them, in order to simplify the code.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This stick uses the same RC-5 remote controll found on other
PCTV devices. So, just use the existing keymap.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The firmware upload routine is already complex enough. Split the
first loop that verifies the firmware size into a separate routine,
making the code more readable.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of hardcoding the firmware files together with the driver,
use request_firmware() way, loading it from userspace.
The firmware files are placed at:
http://linuxtv.org/downloads/firmware/#8
And they'll be latter submitted to linux-firmware git tree.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The state struct is allocated without cleaning the memory.
This causes random bugs.
Clean it, and move the memcpy functions just below each kalloc,
to be clearer that all those data are properly filled.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are memory leaks on both DVB release and
dvb attach error path. Fix them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This var is not used. Remove it from the code, as we'll now be
converting the driver to load the firmware from an external
file.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file is empty (actually, all commented there). So, remove it.
We should latter remove those macros too, or convert them into
a struct to allow dynamically enable the options during device
probing time.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Get rid of another typedef defined on this driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using printk's, use the pr_foo() macros.
That fixes some checkpatch warnings and provide a better error,
warning and debug support.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of defining its own set of error codes, use the linux
native ones.
Please note that this patch made a "stupid" error code mapping, just
replacing the codes with the closest one. In special, -EIO is being
used on several places. I'm pretty sure this could be better assigned,
but a change like that would require lots o time and efforts, without
much benefit.
So lets do adjstments at the error codes latter, when we have more
time.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix almost all checkpatch.pl warnings/errors on drxj.c, except for:
- 80 cols whitespacing;
- too many leading tabs;
- a false positive at DRXJ_16TO8() macro.
- static char array declaration should probably be static const char
as adding "const" would cause warnings.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove three typedefs from drxj.c, using the following script:
use File::Find;
use strict;
my $dir = shift or die "need a dir";
my $type = shift or die "need type";
my $var = shift or die "need var";
sub handle_file {
my $file = shift;
my $out;
open IN, $file or die "can't open $file";
$out .= $_ while (<IN>);
close IN;
$out =~ s/\btypedef\s+($type)\s+\{([\d\D]+?)\s*\}\s+\b($var)[^\;]+\;/$type $var \{\2\};/;
# This replaces the typedef declaration for a simple struct declaration - style 1
# This replaces the typedef declaration for a simple struct declaration - style 2
# Replace struct occurrences
$out =~ s,\b($var)_t\s+,$type \1 ,g;
$out =~ s,\bp_*($var)_t\s+,$type \1 *,g;
$out =~ s,\b($var)_t\b,$type \1,g;
$out =~ s,\bp_*($var)_t\b,$type \1 *,g;
open OUT, ">$file" or die "can't open $file";
print OUT $out;
close OUT;
}
sub parse_dir {
my $file = $File::Find::name;
return if (!($file =~ /.[ch]$/));
handle_file $file;
}
find({wanted => \&parse_dir, no_chdir => 1}, $dir);
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't need to test boolean x == true or x == false.
That makes the code more compact.
patch generated with make coccicheck and manually reviewed.
While here, remove uneeded ';'.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
CodingStyle fix: don't use parenthesis on return, as it is not
a function.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxj_dap_scu_atomic_read_reg16’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:4170:9: warning: ‘*((void *)&buf+1)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word = (u16) (buf[0] + (buf[1] << 8));
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:4170:9: warning: ‘buf’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxj_dap_atomic_read_reg32.isra.59’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:2186:7: warning: ‘*((void *)&buf+3)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word = (u32) buf[3];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2188:10: warning: ‘*((void *)&buf+2)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[2];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2190:10: warning: ‘*((void *)&buf+1)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[1];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2192:10: warning: ‘buf’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[0];
^
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This were fixed with the help of this small perl script:
#!/usr/bin/perl
my $dir = shift or die "need a dir";
my $type = shift or die "need type";
my $var = shift or die "need var";
sub handle_file {
my $file = shift;
my $out;
open IN, $file or die "can't open $file";
$out .= $_ while (<IN>);
close IN;
$out =~ s/\btypedef\s+($type)\s+\{([\d\D]+?)\s*\}\s+\b($var)[^\;]+\;/$type $var \{\2\};/;
$out =~ s,\b($var)_t\s+,$type \1 ,g;
$out =~ s,\bp_*($var)_t\s+,$type \1 *,g;
$out =~ s,\b($var)_t\b,$type \1,g;
$out =~ s,\bp_*($var)_t\b,$type \1 *,g;
open OUT, ">$file" or die "can't open $file";
print OUT $out;
close OUT;
}
sub parse_dir {
my $file = $File::Find::name;
return if (!($file =~ /.[ch]$/));
handle_file $file;
}
find({wanted => \&parse_dir, no_chdir => 1}, $dir);
Some manual work were needed.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of the changes were done with scripts like:
for i in drivers/media/dvb-frontends/drx39xyj/*.[ch]; do perl -ne '$var = "drx_sig_quality"; s,\b($var)_t\s+,struct \1 ,g; s,\bp_*($var)_t\s+,struct \1 *,g; s,\b($var)_t\b,struct \1,g; s,\bp_*($var)_t\b,struct \1 *,g; print $_' <$i >a && mv a $i; done
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file is not used anywhere. Drop it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
None of those vars are used on those functions. Just remove them.
After this patch, there's just one of such warnings:
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function 'ctrl_get_qam_sig_quality':
drivers/media/dvb-frontends/drx39xyj/drxj.c:7872:6: warning: variable 'ber_cnt' set but not used [-Wunused-but-set-variable]
u32 ber_cnt = 0; /* BER count */
We'll keep it, as BER count will be useful when converting the
frontend to report statistics via DVBv5 API
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is not static. Also, it is not used anywhere.
So, drop it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This time, use checkpatch --strict --fix.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There's no reason at all to use CamelCase here. Convert all of
them to normal case.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of manually fixing the issues, use the --fix experimental
checkpatch. That solves a bunch of checkpatch issues.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Patch generated with this script:
for i in drivers/media/dvb-frontends/drx39xyj/*.[ch]; do perl -ne 's,(enum|struct|void|int|u32|u64|u16|u8|s8|s16|s32|s64)\s+(\S+)\s+\*[ ]+,\1 \2 *,g; print $_' <$i >a && mv a $i; done
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are lots of typedefs there. Let's get rid of them.
Most of the work here is due to this small script:
if [ "$3" == "" ]; then
echo "usage: $0 type DRXName drx_name"
fi
t=$1; f=$2; g=$3
for i in *.[ch]; do
sed s,"p${f}_t","$t $g *",g <$i >a && mv a $i && \
sed s,"${f}_t","$t $g",g <$i >a && mv a $i
done
Just kept there the function typedefs, as those are still useful.
Yet, all those tuner_ops can likely be just removed on a latter
cleanup patch.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move them into drx_driver.h
That makes easier to cleanup further what's there at the
headers.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of the work were done by those small scripts:
for i in *; do sed s,pDRXFrequency_t,"s32 *",g <$i >a && mv a $i; done
for i in *; do sed s,DRXFrequency_t,"s32",g <$i >a && mv a $i; done
for i in *; do sed s,pDRXSymbolrate_t,"u32 *",g <$i >a && mv a $i; done
for i in *; do sed s,DRXSymbolrate_t,"u32",g <$i >a && mv a $i; done
for i in *; do sed s,FALSE,false,g <$i >a && mv a $i; done
for i in *; do sed s,TRUE,true,g <$i >a && mv a $i; done
for i in *; do sed s,Bool_t,bool,g <$i >a && mv a $i; done
for i in *; do sed s,pbool,"bool *",g <$i >a && mv a $i; done
The only remaining things there are the return values.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Patch created using this small script:
for j in 8 16 32; do for i in *; do sed s,pu${j}_t,"u$j *",g <$i >a && mv a $i; done; done
for j in 8 16 32; do for i in *; do sed s,ps${j}_t,"s$j *",g <$i >a && mv a $i; done; done
for j in 8 16 32; do for i in *; do sed s,s${j}_t,"s$j",g <$i >a && mv a $i; done; done
for j in 8 16 32; do for i in *; do sed s,u${j}_t,"u$j",g <$i >a && mv a $i; done; done
and fixing the bsp_types.h header.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
After removing the typedef, it is now clear that HICommand() were
abusing of a var that was expecting to be constant:
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘HICommand’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:2272:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2272:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2273:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2273:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2274:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2274:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2275:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2275:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2278:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2278:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2279:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2279:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2291:2: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2291:2: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2311:4: warning: passing argument 1 of ‘drxDapDRXJFunct_g.readReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2311:4: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2315:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.readReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2315:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of the hard work here were done by this small script:
for i in *; do sed s,pI2CDeviceAddr_t,"struct i2c_device_addr *",g <$i >a && mv a $i; done
for i in *; do sed s,I2CDeviceAddr_t,"struct i2c_device_addr",g <$i >a && mv a $i; done
Only bsp_i2c.h were added by hand.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There were some DVB internal API changes, since this driver were
written. Change it to work with the new API.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Do the automatic CodingStyle fixes found at Lindent.
No functional changes.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Relicense the drx-j driver under a standard 3-clause BSD license, which makes
it GPL compatible.
This was done explicitly with permission from Trident Microsystems.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the Trident DRX-J driver, including a card profile for the
PCTV 80e which uses the chip.
Thanks to Trident for allowing the release of this code under a BSD license,
and of course Hauppauge/PCTV for pushing for its release to the community.
[pdickeybeta@gmail.com: modified to fix compilation errors and also to move
the driver files from the drx39xy subdirectory to the frontends directory]
[m.chehab@samsung.com: fix merge conflicts, commented drx-j compilation and
added EM28XX_R06_I2C_CLK setup also to the board setup]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If an attempt to set LNA fails, restore the cache to LNA_AUTO,
in order to make it to reflect the current LNA status.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Several URBs will be simply not filled. Don't call the DVB
core software filter for those empty URBs.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement em28xx_usb_driver suspend, resume, and reset_resume hooks.
These hooks will invoke em28xx core em28xx_suspend_extension() and
em28xx_resume_extension() to suspend and resume registered extensions.
Approach:
Add power management support to em28xx usb driver. This driver works in
conjunction with extensions for each of the functions on the USB device
for video/audio/dvb/remote functionality that is present on media USB
devices it supports. During suspend and resume each of these extensions
will have to do their part in suspending the components they control.
Adding suspend and resume hooks to the existing struct em28xx_ops will
enable the extensions the ability to implement suspend and resume hooks
to be called from em28xx driver. The overall approach is as follows:
-- add suspend and resume hooks to em28xx_ops
-- add suspend and resume routines to em28xx-core to invoke suspend
and resume hooks for all registered extensions.
-- change em28xx dvb, audio, input, and video extensions to implement
em28xx_ops: suspend and resume hooks. These hooks do what is necessary
to suspend and resume the devices they control.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement em28xx_ops: suspend/resume hooks. em28xx usb driver will
invoke em28xx_ops: suspend and resume hooks for all its extensions
from its suspend() and resume() interfaces.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement em28xx_ops: suspend/resume hooks. em28xx usb driver will
invoke em28xx_ops: suspend and resume hooks for all its extensions
from its suspend() and resume() interfaces.
[m.chehab@samsung.com: Fix a breakage caused by calling a non-existing
function call: schedule_delayed_work_sync(), and test if IR was defined
at suspend/resume]
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement em28xx_ops: suspend/resume hooks. em28xx usb driver will
invoke em28xx_ops: suspend and resume hooks for all its extensions
from its suspend() and resume() interfaces.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement em28xx_ops: suspend/resume hooks. em28xx usb driver will
invoke em28xx_ops: suspend and resume hooks for all its extensions
from its suspend() and resume() interfaces.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
em28xx usb driver will have to suspend and resume its extensions. Adding
suspend and resume to em28xx_ops gives extensions the ability to install
suspend and resume that can be invoked from em28xx_usb driver suspend()
and resume() interfaces.
Approach:
Add power management support to em28xx usb driver. This driver works in
conjunction with extensions for each of the functions on the USB device
for video/audio/dvb/remote functionality that is present on media USB
devices it supports. During suspend and resume each of these extensions
will have to do their part in suspending the components they control.
Adding suspend and resume hooks to the existing struct em28xx_ops will
enable the extensions the ability to implement suspend and resume hooks
to be called from em28xx driver. The overall approach is as follows:
-- add suspend and resume hooks to em28xx_ops
-- add suspend and resume routines to em28xx-core to invoke suspend
and resume hooks for all registered extensions.
-- change em28xx dvb, audio, input, and video extensions to implement
em28xx_ops: suspend and resume hooks. These hooks do what is necessary
to suspend and resume the devices they control.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Restructure the way we bring the various GPIOs out of reset. In particular:
1. we only need to setup the GPIOs as outputs once
2. there's no point in writing 0x40 to register 0x00 since that's the EEPROM
write protect and already it's configured as an input
3. Separate out the act of enabling the power supply and bringing the tuner
and demod out of reset. If you don't then the chip may not be properly
enabled (as the power supply is still ramping up when the chip comes
out of reset). This can result in probing failures.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
An attempt was made to read dvbs2_snr_tab[80],
though dvbs2_snr_tab has only 80 elements.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We are checking sizeof() the wrong variable!
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to check lock twice here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add m88rs2000_get_tune_settings, min delay of 2000 ms on symbol
rate more than 3000000 and delay of 3000ms less than this.
Adding min delay prevents crashing the frontend on continuous
transponder scans. Other dvb_frontend_tune_settings remain as default.
This makes very little time difference to good channel scans, but slows down
the set frontend where lock can never be achieved i.e. DVB-S2.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds Controls to set Horizontal and Vertical search range
for Motion Estimation block for Samsung MFC video Encoders.
Signed-off-by: Swami Nathan <swaminath.p@samsung.com>
Signed-off-by: Amit Grover <amit.grover@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adding V4L2 controls for horizontal and vertical search range in pixels
for motion estimation module in video encoder.
Signed-off-by: Swami Nathan <swaminath.p@samsung.com>
Signed-off-by: Amit Grover <amit.grover@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
"err" is zero here so we don't need to check again.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Messages relative to kinect_read() are printing "res" which contains the
return value of a previous kinect_write().
Print the correct value in the messages.
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The error checking code relative to the invocations of kinect_read()
does not return the actual return code of the function just called, it
returns "res" which still contains the value of the last invocation of
a previous kinect_write().
Return the proper value, and while at it also report with -EREMOTEIO the
case of a partial transfer.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Upgrade to videobuf2 libraries.
No errors reported with "v4l2-compliance -s".
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
sleep_on and its variants are broken and going away soon. This changes
the omap vout driver to use wait_event_interruptible_timeout instead,
which fixes potential race where the dma is complete before we
schedule.
[hans.verkuil@cisco.com: replaced interruptible_sleep_on_timeout by
wait_event_interruptible_timeout in the commit msg, obvious typo]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
interruptible_sleep_on is racy and going away. This replaces
one use in the radio-cadet driver with a wait_event_interruptible
call. Special care was taken that accesses to the rdsin and rdsout
indices are always done with dev->lock held.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Closer inspection on exact transmitted format showed that
we needed to add 1 on vertical sync.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
HS_IN/VS_IN was always set to positive.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently only RGB444 input data is supported so set to zero.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Removal of unnecessary parameters from s2255_fh.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Start acquisition return code was not being checked. Return error
if start acquisition fails.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver was allocating a kernel buffer each time it was sending a command.
It is better to allocate this buffer once at startup.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Removing duplicate fmt from buffer structure.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Buffer setup should check if minimum number of buffers is used.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Renaming s2255_channel and all instances of channel to vc (video channel).
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Removal of unused and unnecessary s2255dma_queue structure.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch enables the ioctl to create additional buffers on the
videobuf2 capture queue.
[laurent.pinchart@ideasonboard.com: Acquire privileges instead of just
checking them in VIDIOC_CREATE_BUFS implementation]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The queue_setup handler takes an optional format argument that can be
used to allocate buffers for a format different than the current format.
The uvcvideo driver doesn't support changing the format when buffers
have been allocated, but there's no reason not to support allocating
buffers larger than the minimum size.
When the format argument isn't NULL verify that the requested image size
is large enough for the current format and use it for the buffer size.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
videobuf2 already ensures that the number of buffers will not exceed
VIDEO_MAX_FRAME, which is equal to our arbitraty limit of
UVC_MAX_VIDEO_BUFFERS. Remove the duplicate check.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Isochronous endpoints on devices with speed == USB_SPEED_WIRELESS can
have a max packet size ranging from 1-3584 bytes. Add a case to
uvc_endpoint_max_bpi to handle USB_SPEED_WIRELESS. Otherwise endpoints
for those devices will fall to the default case which masks off any
values > 2047. This causes uvc_init_video to underestimate the
bandwidth available and fail to find a suitable alt setting for high
bandwidth video streams.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
x < constant implies x + unsigned < constant
That check just obfuscates the code
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar