It is not machine-specific, but common irq infrastructure.
Also add the missing asmlinkage, to match its definition.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire processors have a much more limited set of addressing modes
that can be used for most instructions. A number of the atomic operations
have already been fixed to limit the addressing modes used with add and
sub instructions when building for ColdFire. But we missed a few.
Fix the remaining atomic operations to be clean for ColdFire processors.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
When reworking bitops.h to be clean for all processor types we introduced
a CONFIG_CPU_HAS_NO_BITFIELDS define to signal whether this processor type
supported the bit field instructions. The ARCH_SIG_BITOPS functions for
m68k use these instruction types. We should base the use of these functions
(or the generic versions) on the CONFIG_CPU_HAS_NO_BITFIELDS define.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The real difference between the mmu and non-mmu varients of the delay.h
files has nothing to do with having an mmu or not. It is processor family
differences that means slightly different code. Merge the delay_mm.h and
delay_no.h files back into a single file.
The primarly difference we need to deal with is whether the processor
supports a 32bit * 32bit -> 64bit multiply. Without it we need to do some
shift scaling as well as use a 32bit * 32bit -> 32bit multiply. If building
for a multi-CPU type kernel then we must use the simpler mult/shift scaling.
This version of delay code allows the CPU32 family to use a 64bit mul,
since it supports this instruction, the old code did not.
The changes use macros where appropriate to try and optimize constant sized
udelay times. And it removes the use of a fixed lib function for the non-mmu
case. Code size on typical kernel configurations is similar, or only larger
by a few tens of bytes.
Also removed the unused muldiv() code from delay_mm.h.
Build and run tested on ColdFire and ARAnyM. Build tested only on 68328
and 68360 (CPU32).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Currently trap_init() is an empty function for m68knommu. Instead
the vectors are being setup as part of the IRQ initialization.
This is inconsistent with m68k and other architectures.
Change the local init_vectors() to be trap_init(), and init the
vectors at the correct time during startup. This will help merge of
m68k and m68knommu trap code in the furture.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 5206 and 5206e CPU families are almost identical, we can
easily merge the platform support code for them. All the differences
are dealt with in the current include/asm/5206sim.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The following patch merges the mmu and non-mmu versions of the m68k
bitops.h files. Now there is a good deal of difference between the two
files, but none of it is actually an mmu specific difference. It is
all about the specific m68k/coldfire varient we are targeting. So it
makes an awful lot of sense to merge these into a single bitops.h.
There is a number of ways I can see to factor this code. The approach
I have taken here is to keep the various versions of each macro/function
type together. This means that there is some ifdefery with each to handle
each CPU type.
I have added some comments in a couple of appropriate places to try
and make it clear what the differences we are dealing with are.
Specifically the instruction and addressing mode differences we have
to deal with.
The merged form keeps the same underlying optimizations for each CPU
type for all the general bit clear/set/change and find bit operations.
It does switch to using the generic le operations though, instead of
any local varients.
Build tested on ColdFire, 68328, 68360 (which is cpu32) and 68020+.
Run tested on ColdFire and ARAnyM.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
The non-MMU m68k targets can use the same asm/system.h as the MMU
targets. So switch the current system_mm.h to be system.h and remove
system_no.h.
The assembly support code for the non-MMU resume functions needs to
be modified to match the now common switch_to() macro. Specifically
this means correctly saving and restoring the status flags in the case
of the ColdFire resume, and some reordering of the code to not use
registers before they are saved or after they are restored.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The contents of asm/hardirq.h are pretty strait forward for both the
MMU (hardirq_mm.h) and non-MMU (hardirq_no.h) include files. Merge the
two back into a single file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The non-mmu and mmu versions of the module loader module.c are
nearly identical. Merge them back to a single module.c. There is
a little bit of re-ordering of the struct and enum definitions in
module.h to keep the ifdefery to a minimum.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
arch/m68k/mm/init_no.c:123: warning: format "%d" expects type "int", but argument 2 has type "long unsigned int"
And use pr_notice() while we're at it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Some recent changes to the way that ACPI handles wakeup flags
means that the XO15EC ACPI device is not wakeup-capable by
default so device_set_wakeup_enable() does nothing.
Use device_init_wakeup() to mark the device as wakeup capable,
and to enable wakeups.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/20110724173430.BE03C9D401C@zog.reactivated.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As reported by Randy Dunlap, CONFIG_POWER_SUPPLY=m caused a
compile error:
arch/x86/built-in.o: In function `battery_status_changed':
olpc-xo15-sci.c:(.text+0x3acdd): undefined reference to `power_supply_get_by_name'
olpc-xo15-sci.c:(.text+0x3ad04): undefined reference to `power_supply_changed'
The SCI drivers, as bool, require POWER_SUPPLY to be builtin.
Use select to make that a hard requirement and avoid this build
failure.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
This patch removes all the module loader hook implementations in the
architecture specific code where the functionality is the same as that
now provided by the recently added default hooks.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The idea is from Avi:
| We could cache the result of a miss in an spte by using a reserved bit, and
| checking the page fault error code (or seeing if we get an ept violation or
| ept misconfiguration), so if we get repeated mmio on a page, we don't need to
| search the slot list/tree.
| (https://lkml.org/lkml/2011/2/22/221)
When the page fault is caused by mmio, we cache the info in the shadow page
table, and also set the reserved bits in the shadow page table, so if the mmio
is caused again, we can quickly identify it and emulate it directly
Searching mmio gfn in memslots is heavy since we need to walk all memeslots, it
can be reduced by this feature, and also avoid walking guest page table for
soft mmu.
[jan: fix operator precedence issue]
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use rcu to protect shadow pages table to be freed, so we can safely walk it,
it should run fastly and is needed by mmio page fault
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Now, the spte is just from nonprsent to present or present to nonprsent, so
we can use some trick to set/clear spte non-atomicly as linux kernel does
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduce some interfaces to modify spte as linux kernel does:
- mmu_spte_clear_track_bits, it set the spte from present to nonpresent, and
track the stat bits(accessed/dirty) of spte
- mmu_spte_clear_no_track, the same as mmu_spte_clear_track_bits except
tracking the stat bits
- mmu_spte_set, set spte from nonpresent to present
- mmu_spte_update, only update the stat bits
Now, it does not allowed to set spte from present to present, later, we can
drop the atomicly opration for X86_32 host, and it is the preparing work to
get spte on X86_32 host out of the mmu lock
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduce handle_abnormal_pfn to handle fault pfn on page fault path,
introduce mmu_invalid_pfn to handle fault pfn on prefetch path
It is the preparing work for mmio page fault support
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If the page fault is caused by mmio, the gfn can not be found in memslots, and
'bad_pfn' is returned on gfn_to_hva path, so we can use 'bad_pfn' to identify
the mmio page fault.
And, to clarify the meaning of mmio pfn, we return fault page instead of bad
page when the gfn is not allowd to prefetch
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The idea is from Avi:
| Maybe it's time to kill off bypass_guest_pf=1. It's not as effective as
| it used to be, since unsync pages always use shadow_trap_nonpresent_pte,
| and since we convert between the two nonpresent_ptes during sync and unsync.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Split kvm_mmu_free_page to kvm_mmu_isolate_page and
kvm_mmu_free_page
One is used to remove the page from cache under mmu lock and the other is
used to free page table out of mmu lock
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Move counting used shadow pages from commiting path to preparing path to
reduce tlb flush on some paths
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If 'pt_write' is true, we need to emulate the fault. And in later patch, we
need to emulate the fault even though it is not a pt_write event, so rename
it to better fit the meaning
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
gw->pte_access is the final access permission, since it is unified with
gw->pt_access when we walked guest page table:
FNAME(walk_addr_generic):
pte_access = pt_access & FNAME(gpte_access)(vcpu, pte, true);
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If dirty bit is not set, we can make the pte access read-only to avoid handing
dirty bit everywhere
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If the page fault is caused by mmio, we can cache the mmio info, later, we do
not need to walk guest page table and quickly know it is a mmio fault while we
emulate the mmio instruction
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduce vcpu_mmio_gva_to_gpa to translate the gva to gpa, we can use it
to cleanup the code between read emulation and write emulation
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Properly check the last mapping, and do not walk to the next level if last spte
is met
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements the kvm bits of the steal time infrastructure.
The most important part of it, is the steal time clock. It is an
continuous clock that shows the accumulated amount of steal time
since vcpu creation. It is supposed to survive cpu offlining/onlining.
[marcelo: fix build with CONFIG_KVM_GUEST=n]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Tested-by: Eric B Munson <emunson@mgebm.net>
CC: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
CC: Peter Zijlstra <peterz@infradead.org>
CC: Avi Kivity <avi@redhat.com>
CC: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Provide additional information on SIGTRAP by using a sig_info signal.
Use TRAP_BRKPT for breakpoints via illegal operation and TRAP_HWBKPT
for breakpoints via program event recording. Provide the address of
the instruction that caused the breakpoint via si_addr.
While we are at it get rid of tracehook_consider_fatal_signal.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
SIGP emerg needs to pass the source vpu adress into __LC_CPU_ADDRESS of the
target guest.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cpu measurement alerts that are used for instance by oprofile
for hardware sampling are not turned off on a cpu that is going
offline. Add the appropriate control register bit that should be
disabled to the list.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not set the cr0 enablement bit for iucv by default in head[31|64].S,
move the enablement to iucv_init in the iucv base layer.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The (un-)register_external_interrupt functions are not race safe if
more than one interrupt handler is added or deleted for an external
interrupt concurrently.
Make the registration / unregistration of external interrupts race safe
by using RCU and a spinlock. RCU is used to avoid a performance penalty
in the external interrupt handler, the register and unregister functions
are protected by the spinlock and are not performance critical.
call_rcu must be used since the SCLP driver uses the interface with
IRQs disabled. Also use the generic list implementation rather than
homebrewn list code.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch removes the mmu reload logic for kvm on s390. Via Martin's
new gmap interface, we can safely add or remove memory slots while
guest CPUs are in-flight. Thus, the mmu reload logic is not needed
anymore.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch removes kvm-s390 internal assumption of a linear mapping
of guest address space to user space. Previously, guest memory was
translated to user addresses using a fixed offset (gmsor). The new
code uses gmap_fault to resolve guest addresses.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch switches kvm from using (Qemu's) user address space to
Martin's gmap address space. This way QEMU does not have to use a
linker script in order to fit large guests at low addresses in its
address space.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add code that allows KVM to control the virtual memory layout that
is seen by a guest. The guest address space uses a second page table
that shares the last level pte-tables with the process page table.
If a page is unmapped from the process page table it is automatically
unmapped from the guest page table as well.
The guest address space mapping starts out empty, KVM can map any
individual 1MB segments from the process virtual memory to any 1MB
aligned location in the guest virtual memory. If a target segment in
the process virtual memory does not exist or is unmapped while a
guest mapping exists the desired target address is stored as an
invalid segment table entry in the guest page table.
The population of the guest page table is fault driven.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The alignment is missing for various global symbols in s390 assembly code.
With a recent gcc and an instruction like stgrl this can lead to a
specification exception if the instruction uses such a mis-aligned address.
Specify the alignment explicitely and while add it define __ALIGN for s390
and use the ENTRY define to save some lines of code.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The entry to / exit from sie has subtle dependencies to the first level
interrupt handler. Move the sie assembler code to entry64.S and replace
the SIE_HOOK callback with a test and the new _TIF_SIE bit.
In addition this patch fixes several problems in regard to the check for
the_TIF_EXIT_SIE bits. The old code checked the TIF bits before executing
the interrupt handler and it only modified the instruction address if it
pointed directly to the sie instruction. In both cases it could miss
a TIF bit that normally would cause an exit from the guest and would
reenter the guest context.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When running a kvm guest we can get intercepts for tprot, if the host
page table is read-only or not populated. This patch implements the
most common case (linux memory detection).
This also allows host copy on write for guest memory on newer systems.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not trace arch_local_save_flags(), arch_local_irq_*() and friends.
Although they are marked inline, gcc may still make a function out of
them and add it to the pool of functions that are traced by the function
tracer. This can cause undesirable results (kernel panic, triple faults,
etc).
Add the notrace notation to prevent them from ever being traced.
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'x86-detect-hyper-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hyper: Change hypervisor detection order
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix DNA exception during check_fpu()
* 'x86-kexec-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
kexec, x86: Fix incorrect jump back address if not preserving context
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, config: Introduce an INTEL_MID configuration
* 'x86-quirks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, quirks: Use pci_dev->revision
* 'x86-tsc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: tsc: Remove unneeded DMI-based blacklisting
* 'x86-smpboot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, boot: Wait for boot cpu to show up if nr_cpus limit is about to hit
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: apb: Share APB timer code with other platforms
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
um: Make rwsem.S depend on CONFIG_RWSEM_XCHGADD_ALGORITHM
* 'core-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debug: Make CONFIG_EXPERT select CONFIG_DEBUG_KERNEL to unhide debug options
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Remove unused CHECK_IRQ_PER_CPU()
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools, x86: Fix 32-bit compile on 64-bit system
virtio has been so far used only in the context of virtualization,
and the virtio Kconfig was sourced directly by the relevant arch
Kconfigs when VIRTUALIZATION was selected.
Now that we start using virtio for inter-processor communications,
we need to source the virtio Kconfig outside of the virtualization
scope too.
Moreover, some architectures might use virtio for both virtualization
and inter-processor communications, so directly sourcing virtio
might yield unexpected results due to conflicting selections.
The simple solution offered by this patch is to always source virtio's
Kconfig in drivers/Kconfig, and remove it from the appropriate arch
Kconfigs. Additionally, a virtio menu entry has been added so virtio
drivers don't show up in the general drivers menu.
This way anyone can use virtio, though it's arguably less accessible
(and neat!) for virtualization users now.
Note: some architectures (mips and sh) seem to have a VIRTUALIZATION
menu merely for sourcing virtio's Kconfig, so that menu is removed too.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The pcm driver name has been changed, but the device name has not.
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Do not trace arch_local_save_flags(), arch_local_irq_*() and friends.
Although they are marked inline, gcc may still make a function out of
them and add it to the pool of functions that are traced by the function
tracer. This can cause undesirable results (kernel panic, triple faults,
etc).
Add the notrace notation to prevent them from ever being traced.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The bug in the BF526 rom when doing a software reset exists only in older
silicon versions, so don't clear SWRST on newer parts.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF51x's alternative portmux Kconfig options were copy & pasted from
the BF52x, but never tweaked to reflect it. So drop the old options as
they were never used (and were simply wrong), and add the BF51x specific
pieces to the Kconfig and header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Back in commit c03c2a8734, we fixed logic in the non-bf54x
GPIO resume code to set the data levels properly before the direction
to avoid spurious line glitches. But we missed the bf54x code paths.
So add the same fix there.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
No need to reload these registers constantly since they're always
available (we're not making any function calls in between).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin C ABI says we do not need to save/restore R0-R3 and P0-P2
as they are available as scratch registers. So don't bother.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Re-architect how we save/restore the gpio/port logic that only pertains
to bf538/bf539 parts by pulling it out of the core code paths and pushing
it out to bf538-specific locations.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current save logic used in hibernation is to do a MMR load (base +
offset) into a register, and then push that onto the stack. Then when
restoring, pop off the stack into a register followed by a MMR store
(base + offset). These use plenty of 32bit insns rather than 16bit,
are pretty long winded, and full of pipeline bubbles.
So, by taking advantage of MMRs that are contiguous, the multi-register
push/pop insn, and register abuse, we can shrink this code considerably.
When saving, the new logic does a lot of loads into the data and pointer
registers before executing a single multi-register push insn. Then when
restoring, we do a single multi-register pop insn followed by a lot of
stores. Overall, this allows us to cut the insn count by ~30%, the code
size by ~45%, and drastically reduce the register hazards that trigger
bubbles in the pipeline.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
EVT0 is for emulation, EVT1 is for reset, and EVT4 is the "global int
disable" region. None of these are used by software (or even hardware),
so don't bother saving/restoring them when we hibernate since nothing
ever uses these in Linux (the only thing they would be useful for is
core-memory scratch, but that's just crazy talk).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This defines only get used in the hibernate code, so remove them from the
global dpmc header as no one else cares.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The RETE/RETN registers are only used in emulation(JTAG) and NMI nodes,
or as scratch registers, neither of which need to be saved/restored as
this code doesn't execute at those core event levels.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
For parts with more than one SIC_IWR, we can optimize the writing
a little bit using better Blackfin insns.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Have the logic that uses peripheral interrupt blocks key off of pint
defines rather than CPU names so that things are generalized across
families.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Have the code work off of MMR names rather than CPU defines so there is
less code to tweak in the future with new parts.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These defines don't accomplish much as GPIO_# is the same thing as #.
Each CPU already provides helpful symbolic defines like GPIO_<PIN>
which everyone uses, so just punt these # ones.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Not sure how these guys slipped in, but they're annoying me.
So bring these unicode space gremlins down to earth to normal
ascii spaces.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
For now, this only supports gptimers. Support for dedicated PWM devices
as found on newer parts to come.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The API is geared around timer ids, except for the act of enabling
and disabling timers. So add a small helper to fill out the gap.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The alignment is normally handled by PERCPU(), but we need to do it
ourselves in the XIP build due to the custom layout.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that asm/gptimers.h has the hardware register struct layout, there's
no need to duplicate things locally.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Passing a non-simple expression in as the addr arg could incorrectly
apply the pointer cast resulting in misbehavior. Add proper paren.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The documentation for the IMDMA channels appears to be incorrect.
These DMA blocks don't actually have PERIPHERAL_MAP MMRs for us
to access. Attempts to do so lead to system mmr hardware errors.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin mutex.h is merely a copy of an older asm-generic/mutex-dec.h,
so punt it and just use the common one directly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This moves the double fault data used at boot time into a single struct
which can then easily be addressed with indexed loads rather than having
to explicitly load multiple addresses.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The default for the Blackfin SPI driver is 8 bits and dma disabled,
so many of the bfin5xx_spi_chip resources are redundant. So punt
those parts.
Further, drivers should themselves be declaring 16 bit transfers,
so for those that do, and for the ones which no longer do 16 bit
transfers, drop the bfin5xx_spi_chip resources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-64, vdso: Do not allocate memory for the vDSO
clocksource: Change __ARCH_HAS_CLOCKSOURCE_DATA to a CONFIG option
x86, vdso: Drop now wrong comment
Document the vDSO and add a reference parser
ia64: Replace clocksource.fsys_mmio with generic arch data
x86-64: Move vread_tsc and vread_hpet into the vDSO
clocksource: Replace vread with generic arch data
x86-64: Add --no-undefined to vDSO build
x86-64: Allow alternative patching in the vDSO
x86: Make alternative instruction pointers relative
x86-64: Improve vsyscall emulation CS and RIP handling
x86-64: Emulate legacy vsyscalls
x86-64: Fill unused parts of the vsyscall page with 0xcc
x86-64: Remove vsyscall number 3 (venosys)
x86-64: Map the HPET NX
x86-64: Remove kernel.vsyscall64 sysctl
x86-64: Give vvars their own page
x86-64: Document some of entry_64.S
x86-64: Fix alignment of jiffies variable
* 'x86-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Kill handle_signal()->set_fs()
x86, do_signal: Simplify the TS_RESTORE_SIGMASK logic
x86, signals: Convert the X86_32 code to use set_current_blocked()
x86, signals: Convert the IA32_EMULATION code to use set_current_blocked()
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mce: Use mce_sysdev_ prefix to group functions
x86, mce: Use mce_chrdev_ prefix to group functions
x86, mce: Cleanup mce_read()
x86, mce: Cleanup mce_create()/remove_device()
x86, mce: Check the result of ancient_init()
x86, mce: Introduce mce_gather_info()
x86, mce: Replace MCM_ with MCI_MISC_
x86, mce: Replace MCE_SELF_VECTOR by irq_work
x86, mce, severity: Clean up trivial coding style problems
x86, mce, severity: Cleanup severity table
x86, mce, severity: Make formatting a bit more readable
x86, mce, severity: Fix two severities table signatures
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, smpboot: Mark the names[] array in __inquire_remote_apic() as const
x86: Convert vmalloc()+memset() to vzalloc()
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, ioapic: Print IR_IO_APIC_route_entry when IR is enabled
x86, ioapic: Print IRTE when IR is enabled
x86, x2apic: Preserve high 32-bits of IA32_APIC_BASE MSR
x86, ioapic: Also print Dest field
x86, ioapic: Format clean up for IOAPIC output
x86: print APIC data a little later during boot
* 'timers-rtc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Serialize EFI time accesses on rtc_lock
x86: Serialize SMP bootup CMOS accesses on rtc_lock
rtc: stmp3xxx: Remove UIE handlers
rtc: stmp3xxx: Get rid of mach-specific accessors
rtc: stmp3xxx: Initialize drvdata before registering device
rtc: stmp3xxx: Port stmp-functions to mxs-equivalents
rtc: stmp3xxx: Restore register definitions
rtc: vt8500: Use define instead of hardcoded value for status bit
* 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mips: Fix i8253 clockevent fallout
i8253: Cleanup outb/inb magic
arm: Footbridge: Use common i8253 clockevent
mips: Use common i8253 clockevent
x86: Use common i8253 clockevent
i8253: Create common clockevent implementation
i8253: Export i8253_lock unconditionally
pcpskr: MIPS: Make config dependencies finer grained
pcspkr: Cleanup Kconfig dependencies
i8253: Move remaining content and delete asm/i8253.h
i8253: Consolidate definitions of PIT_LATCH
x86: i8253: Consolidate definitions of global_clock_event
i8253: Alpha, PowerPC: Remove unused asm/8253pit.h
alpha: i8253: Cleanup remaining users of i8253pit.h
i8253: Remove I8253_LOCK config
i8253: Make pcsp sound driver use the shared i8253_lock
i8253: Make pcspkr input driver use the shared i8253_lock
i8253: Consolidate all kernel definitions of i8253_lock
i8253: Unify all kernel declarations of i8253_lock
i8253: Create linux/i8253.h and use it in all 8253 related files
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (24 commits)
sched: Cleanup duplicate local variable in [enqueue|dequeue]_task_fair
sched: Replace use of entity_key()
sched: Separate group-scheduling code more clearly
sched: Reorder root_domain to remove 64 bit alignment padding
sched: Do not attempt to destroy uninitialized rt_bandwidth
sched: Remove unused function cpu_cfs_rq()
sched: Fix (harmless) typo 'CONFG_FAIR_GROUP_SCHED'
sched, cgroup: Optimize load_balance_fair()
sched: Don't update shares twice on on_rq parent
sched: update correct entity's runtime in check_preempt_wakeup()
xtensa: Use generic config PREEMPT definition
h8300: Use generic config PREEMPT definition
m32r: Use generic PREEMPT config
sched: Skip autogroup when looking for all rt sched groups
sched: Simplify mutex_spin_on_owner()
sched: Remove rcu_read_lock() from wake_affine()
sched: Generalize sleep inside spinlock detection
sched: Make sleeping inside spinlock detection working in !CONFIG_PREEMPT
sched: Isolate preempt counting in its own config option
sched: Remove pointless in_atomic() definition check
...
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (123 commits)
perf: Remove the nmi parameter from the oprofile_perf backend
x86, perf: Make copy_from_user_nmi() a library function
perf: Remove perf_event_attr::type check
x86, perf: P4 PMU - Fix typos in comments and style cleanup
perf tools: Make test use the preset debugfs path
perf tools: Add automated tests for events parsing
perf tools: De-opt the parse_events function
perf script: Fix display of IP address for non-callchain path
perf tools: Fix endian conversion reading event attr from file header
perf tools: Add missing 'node' alias to the hw_cache[] array
perf probe: Support adding probes on offline kernel modules
perf probe: Add probed module in front of function
perf probe: Introduce debuginfo to encapsulate dwarf information
perf-probe: Move dwarf library routines to dwarf-aux.{c, h}
perf probe: Remove redundant dwarf functions
perf probe: Move strtailcmp to string.c
perf probe: Rename DIE_FIND_CB_FOUND to DIE_FIND_CB_END
tracing/kprobe: Update symbol reference when loading module
tracing/kprobes: Support module init function probing
kprobes: Return -ENOENT if probe point doesn't exist
...
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: Fix wrong check in list_splice_init_rcu()
net,rcu: Convert call_rcu(xt_rateest_free_rcu) to kfree_rcu()
sysctl,rcu: Convert call_rcu(free_head) to kfree
vmalloc,rcu: Convert call_rcu(rcu_free_vb) to kfree_rcu()
vmalloc,rcu: Convert call_rcu(rcu_free_va) to kfree_rcu()
ipc,rcu: Convert call_rcu(ipc_immediate_free) to kfree_rcu()
ipc,rcu: Convert call_rcu(free_un) to kfree_rcu()
security,rcu: Convert call_rcu(sel_netport_free) to kfree_rcu()
security,rcu: Convert call_rcu(sel_netnode_free) to kfree_rcu()
ia64,rcu: Convert call_rcu(sn_irq_info_free) to kfree_rcu()
block,rcu: Convert call_rcu(disk_free_ptbl_rcu_cb) to kfree_rcu()
scsi,rcu: Convert call_rcu(fc_rport_free_rcu) to kfree_rcu()
audit_tree,rcu: Convert call_rcu(__put_tree) to kfree_rcu()
security,rcu: Convert call_rcu(whitelist_item_free) to kfree_rcu()
md,rcu: Convert call_rcu(free_conf) to kfree_rcu()
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
iommu/core: Fix build with INTR_REMAP=y && CONFIG_DMAR=n
iommu/amd: Don't use MSI address range for DMA addresses
iommu/amd: Move missing parts to drivers/iommu
iommu: Move iommu Kconfig entries to submenu
x86/ia64: intel-iommu: move to drivers/iommu/
x86: amd_iommu: move to drivers/iommu/
msm: iommu: move to drivers/iommu/
drivers: iommu: move to a dedicated folder
x86/amd-iommu: Store device alias as dev_data pointer
x86/amd-iommu: Search for existind dev_data before allocting a new one
x86/amd-iommu: Allow dev_data->alias to be NULL
x86/amd-iommu: Use only dev_data in low-level domain attach/detach functions
x86/amd-iommu: Use only dev_data for dte and iotlb flushing routines
x86/amd-iommu: Store ATS state in dev_data
x86/amd-iommu: Store devid in dev_data
x86/amd-iommu: Introduce global dev_data_list
x86/amd-iommu: Remove redundant device_flush_dte() calls
iommu-api: Add missing header file
Fix up trivial conflicts (independent additions close to each other) in
drivers/Makefile and include/linux/pci.h
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (51 commits)
PM: Improve error code of pm_notifier_call_chain()
PM: Add "RTC" to PM trace time stamps to avoid confusion
PM / Suspend: Export suspend_set_ops, suspend_valid_only_mem
PM / Suspend: Add .suspend_again() callback to suspend_ops
PM / OPP: Introduce function to free cpufreq table
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
...
* 'ptrace' of git://git.kernel.org/pub/scm/linux/kernel/git/oleg/misc: (39 commits)
ptrace: do_wait(traced_leader_killed_by_mt_exec) can block forever
ptrace: fix ptrace_signal() && STOP_DEQUEUED interaction
connector: add an event for monitoring process tracers
ptrace: dont send SIGSTOP on auto-attach if PT_SEIZED
ptrace: mv send-SIGSTOP from do_fork() to ptrace_init_task()
ptrace_init_task: initialize child->jobctl explicitly
has_stopped_jobs: s/task_is_stopped/SIGNAL_STOP_STOPPED/
ptrace: make former thread ID available via PTRACE_GETEVENTMSG after PTRACE_EVENT_EXEC stop
ptrace: wait_consider_task: s/same_thread_group/ptrace_reparented/
ptrace: kill real_parent_is_ptracer() in in favor of ptrace_reparented()
ptrace: ptrace_reparented() should check same_thread_group()
redefine thread_group_leader() as exit_signal >= 0
do not change dead_task->exit_signal
kill task_detached()
reparent_leader: check EXIT_DEAD instead of task_detached()
make do_notify_parent() __must_check, update the callers
__ptrace_detach: avoid task_detached(), check do_notify_parent()
kill tracehook_notify_death()
make do_notify_parent() return bool
ptrace: s/tracehook_tracer_task()/ptrace_parent()/
...
* 'of-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
pci/of: Consolidate pci_bus_to_OF_node()
pci/of: Consolidate pci_device_to_OF_node()
x86/devicetree: Use generic PCI <-> OF matching
microblaze/pci: Move the remains of pci_32.c to pci-common.c
microblaze/pci: Remove powermac originated cruft
pci/of: Match PCI devices to OF nodes dynamically
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/imx: add device tree probe support
spi/imx: copy gpio number passed by platform data into driver private data
spi/imx: use soc name in spi device type naming scheme
spi/imx: merge type SPI_IMX_VER_0_7 into SPI_IMX_VER_0_4
spi/imx: do not use spi_imx2_3 to name SPI_IMX_VER_2_3 function and macro
spi/imx: use mx21 to name SPI_IMX_VER_0_0 function and macro
spi/imx: do not make copy of spi_imx_devtype_data
spi/dw: Add spi number into spi irq desc
spi/tegra: Use engineering names in DT compatible property
spi/fsl_spi: fix CPM spi driver
mach-s3c2410: remove unused spi-gpio.h file
spi: remove obsolete spi-s3c24xx-gpio driver
mach-gta2: remove unused spi-gpio.h include
mach-qt2410: convert to spi_gpio
mach-jive: convert to spi_gpio
spi/pxa2xx: Remove unavailable ssp_type from documentation
spi/bfin_spi: uninline fat queue funcs
spi/bfin_spi: constify pin array
spi/bfin_spi: use structs for accessing hardware regs
spi/topcliff-pch: Support new device ML7223 IOH
...
Fix up trivial conflict in arch/arm/mach-ep93xx/Makefile
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1287 commits)
icmp: Fix regression in nexthop resolution during replies.
net: Fix ppc64 BPF JIT dependencies.
acenic: include NET_SKB_PAD headroom to incoming skbs
ixgbe: convert to ndo_fix_features
ixgbe: only enable WoL for magic packet by default
ixgbe: remove ifdef check for non-existent define
ixgbe: Pass staterr instead of re-reading status and error bits from descriptor
ixgbe: Move interrupt related values out of ring and into q_vector
ixgbe: add structure for containing RX/TX rings to q_vector
ixgbe: inline the ixgbe_maybe_stop_tx function
ixgbe: Update ATR to use recorded TX queues instead of CPU for routing
igb: Fix for DH89xxCC near end loopback test
e1000: always call e1000_check_for_link() on e1000_ce4100 MACs.
netxen: add fw version compatibility check
be2net: request native mode each time the card is reset
ipv4: Constrain UFO fragment sizes to multiples of 8 bytes
virtio_net: Fix panic in virtnet_remove
ipv6: make fragment identifications less predictable
ipv6: unshare inetpeers
can: make function can_get_bittiming static
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: Fix in/out emulation
lguest: Fix translation count about wikipedia's cpuid page
lguest: Fix three simple typos in comments
lguest: update comments
lguest: Simplify device initialization.
lguest: don't rewrite vmcall instructions
lguest: remove remaining vmcall
lguest: use a special 1:1 linear pagetable mode until first switch.
lguest: Do not exit on non-fatal errors
* 'stable/drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Have 'passthrough' option instead of XEN_PCIDEV_BACKEND_PASS and XEN_PCIDEV_BACKEND_VPCI
xen/pciback: Remove the DEBUG option.
xen/pciback: Drop two backends, squash and cleanup some code.
xen/pciback: Print out the MSI/MSI-X (PIRQ) values
xen/pciback: Don't setup an fake IRQ handler for SR-IOV devices.
xen: rename pciback module to xen-pciback.
xen/pciback: Fine-grain the spinlocks and fix BUG: scheduling while atomic cases.
xen/pciback: Allocate IRQ handler for device that is shared with guest.
xen/pciback: Disable MSI/MSI-X when reseting a device
xen/pciback: guest SR-IOV support for PV guest
xen/pciback: Register the owner (domain) of the PCI device.
xen/pciback: Cleanup the driver based on checkpatch warnings and errors.
xen/pciback: xen pci backend driver.
xen: tmem: self-ballooning and frontswap-selfshrinking
xen: Add module alias to autoload backend drivers
xen: Populate xenbus device attributes
xen: Add __attribute__((format(printf... where appropriate
xen: prepare tmem shim to handle frontswap
xen: allow enable use of VGA console on dom0
* 'stable/pci.cleanups.v1' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Use 'acpi_gsi_to_irq' value unconditionally.
xen/pci: Remove 'xen_allocate_pirq_gsi'.
xen/pci: Retire unnecessary #ifdef CONFIG_ACPI
xen/pci: Move the allocation of IRQs when there are no IOAPIC's to the end
xen/pci: Squash pci_xen_initial_domain and xen_setup_pirqs together.
xen/pci: Use the xen_register_pirq for HVM and initial domain users
xen/pci: In xen_register_pirq bind the GSI to the IRQ after the hypercall.
xen/pci: Provide #ifdef CONFIG_ACPI to easy code squashing.
xen/pci: Update comments and fix empty spaces.
xen/pci: Shuffle code around.
Adds README file, TODO list, and a couple of other pieces that didn't seem
to fit into any other patch.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The OpenRISC Linux kernel conforms to the "generic" syscall interface which
contains only the reduced set of syscalls deemed necessary for new
architectures. Unfortunately, the uClibc port for OpenRISC does not fully
support this reduced set; as such, an additional patch available out-of-tree
needs to be applied to the kernel in order to use the current uClibc. This
is just a temporary measure until the libc port can be straightened out; it
is likely that OpenRISC will make the transition to glibc shortly where the
generic syscall interface is better supported.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This patch adds support for the OpenRISC PIC.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Cc: tglx@linutronix.de
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Geert Uytterhoeven