GEN_CLK is able to route several internal clocks to one of the SoC
pads. In the future, even more clocks could be made accessible using
cts_msr_clk - the clock measure block.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Adding clocks for the pcie driver. Due to the ASIC design,
the pcie controller re-use part of the mipi clock logic,
so the mipi clock is also added.
Tested-by: Jianxin Qin <jianxin.qin@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[amended to remove unnecessary locales]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
clk-audio-divider is no longer used, we can remove it.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
It is actually a lot easier to setup the PLL with carefully chosen rates
than relying on CCF clock propagation for this audio use case.
This way, we can make sure we will always be able to provide the common
audio clock rates, while having the PLL in the optimal operating range.
For this, we stop the rate propagation at the mux picking the
PLL and let it round to the closest matching PLL.
Doing so, we can use the generic divider for the i2s clock.
clk-audio-divider is no longer required. It was a (poor) attempt
to use CCF rate propagation while making sure the PLL rate would
be high enough to work with audio use cases.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The axg audio clock controller is the clock generation unit for the
amlogic audio subsystem of A113 based SoCs. It may be clocked by 8
different plls provided by the primary clock controller and also by
10 slave bit clocks and 10 slave sample clocks which may be provided
by external components, such as audio codecs, through the SoC pads.
It contains several muxes, dividers and gates which are fed into the
the different devices of the audio subsystem.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add a driver to control the clock divider found in the sample clock
generator of the axg audio clock controller.
The sclk divider accumulates specific features which make the generic
divider unsuitable to control it:
- zero based divider (div = val + 1), but zero value gates the clock,
so minimum divider value is 2.
- lrclk variant may adjust the duty cycle depending the divider value
and the 'hi' value.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add a driver to control the output of the sample clock generator found
in the axg audio clock controller.
The goal of this driver is to coherently control the phase provided to
the different element using the sample clock generator. This simplify
the usage of the sample clock generator a lot, without comprising the
ability of the SoC.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add a driver based meson clk-regmap to control clock phase on
amlogic SoCs
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Clean the dependencies in meson clock Kconfig.
CLK_AMLOGIC should actually select CLK_REGMAP_MESON which it uses. Also,
each platform should select CLK_AMLOGIC, so everything is properly turned
on when the platform Kconfig enable each configuration flag
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The legacy method to access the hhi register space is not longer used.
We can safely drop it now.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Apparently there was an attempt to avoid out-of-bounds accesses when there
is only one memory timing available, but there is a typo in the code that
neglects that attempt.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Memory Controller should be always-on. Currently the sibling EMC clock is
marked as critical, let's mark MC clock too for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The current default is to leave the VDE clock's parent at the default,
which is clk_m. However, that is not a configuration that will allow the
VDE to function. Reparent it to pll_c3 instead to make sure the hardware
can actually decode video content.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
By default, the vic03 clock is a child of pll_m but that runs at 924 MHz
which is too fast for VIC. Make vic03 a child of pll_c3 by default so it
will run at a supported frequency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When registering clocks, we just skip any that fail to register
(leaving a NULL hole in the clock table). However, our of_xlate
function still tries to dereference each entry while looking for
the clock with the requested id, causing a crash if any clocks
failed to register. Add a check to of_xlate to skip any NULL
clocks.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Register, shift and mask were wrong according to datasheet.
Fixes: 115510053e ("clk: rockchip: add clock controller for the RK3399")
Cc: stable@vger.kernel.org
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Frequency table macro is used by multiple clock drivers, move frequency
table macro to common header file.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This driver uses sizes.h, but relies on it being implicitly included
somewhere else breaking random direct compilation of the file. Include
sizes.h so we can build it those configurations too for better compile
coverage.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Instead of explicitly enabling critical clocks via clk_prepare_enable(),
let's use the standard CLK_IS_CRITICAL flag instead, which makes the code
a bit shorter.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to Reference Manual Rev.0, 06/2017, there are GPIO LPCGs
defined in CCM CCGRs, add them into clock tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The SDCLK was named SDCLKCLK, and no one has used this yet.
Fix it.
Signed-off-by: Lei YU <mine260309@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This clock is especially used by the RTC driver, so export it so that
devicetree users can use it.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is used by the host to talk to the BMC's PCIe slave device. The BMC
is not involved, but the clock needs to be enabled so the host can use
the device.
Fixes: 15ed8ce5f8 ("clk: aspeed: Register gated clocks")
Cc: stable@vger.kernel.org # 4.15
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds a driver for MAX9485, a programmable audio clock generator.
The device requires a 27.000 MHz clock input. It can provide a gated
buffered output of its input clock and two gated outputs of a PLL that can
generate one out of 16 discrete frequencies. There is only one PLL however,
so the two gated outputs will always have the same frequency but they can
be switched individually.
The driver for this device exposes 4 clocks in total:
- MAX9485_MCLKOUT: A gated, buffered output of the input clock
- MAX9485_CLKOUT: A PLL that can be configured to 16 different
discrete frequencies
- MAX9485_CLKOUT[1,2]: Two gated outputs for MAX9485_CLKOUT
Some PLL output frequencies can be achieved with different register
settings. The driver will select the one with lowest jitter in such cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
[sboyd@kernel.org: Use local variable for val in max9485_clkout_recalc_rate()
and shorten line of max9485_of_clk_get()]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The UDC clock of the JZ4740 SoC can be gated, but the data structure
representing it was missing the CGU_CLK_GATE flag to make it work.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The register field for configuring the divider for the i2s clock
occupies the bits [8-0], which means 9 bits and not 8.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Patch (7705bb7176 clk: qcom: mmcc-msm8996: leave all mmagic gdscs
and clocks always enabled") makes all mmgaic gdscs ALWAYS_ON.
The mmagic_bimc_gdsc is also needed to be turned on to get display
working on 8x96.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 7705bb7176 ("clk: qcom: mmcc-msm8996: leave all mmagic gdscs and clocks always enabled")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This driver is a simple muxing driver that controls the
I2S's clock input by using syscon/regmap to change the parent.
The available inputs can be peripheral clock and generated clock.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
[sboyd@kernel.org: Fix SPDX tag comment style]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The first parent of the sdmmc_free_clk should be the main_sdmmc_clk.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a clock mux that is used as a parent for the mpu_free_clk.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- fix racalculation error in the clk_audio_divider
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE9OFZrhjz9W1fG7cb5vwPHDfy2oUFAls7K6wACgkQ5vwPHDfy
2oVqgA/+I7+quYyvKga+1oeIJUbbdlnldB25Fr/o0jsyMXqwRDPUsMmfg1JsUaSR
symbn1Ic3H7dB+Gy2JWCwOl/Avz6D27CUeypt3A0ckhD1KcO+1+SahtRhiSKVxXw
ZlXDEvTq7Ipb6xjX01LLHeXIXF/Fsic9DvTgBPFVjVELsTrl2H13UXQFSbFuFWMw
/nLWYRAvjJqce7UZh+QZcjwJaev8RAFCcbt8ER4C8ReRcGYp3nJnOENTo5otYu/n
i3xP458SDj8QUaMrsBj3zq07h3gpHhbb+mMSuo6ru0+h/V8eviSP1cDPNxy1DawT
TOs56UfO5aQuelQuAC/Xxvne7iyUBa2OdMp8Nj0zhBrW0A39qZxNdZv8als7Ej8n
Z4VhWgjk/3UCnLDYJ8VINIX9fmcljnMV02WY32Djn0p7GJqnQyoY1GwWlje1Jidd
+CqlcMyYKaoIDTuYFHwuHLFy3Tepbq8u5fIuqJG1x9rF8rHeeWNRIMEPB7mCyPzS
H9fcJdOiiCTyGGHT3HIBx3VYPyZkFj0gbGR4nBMEce9JIBWdrfTqhRzxh7HC29Ek
8GuqY6UXscD1cyh3jcmGdW9Y6XqXSvkmbzAUAdGvWBZPBGsFWMgWbQ5bgIhZe9cY
LFrYsZ+D/bvkI9HBylCV2BGoHAU8ApgwCx/BNy/BIONqYyFjldA=
=QyDk
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-fixes-4.18-1' of https://github.com/BayLibre/clk-meson into clk-fixes
Pull Amlogic clk driver fixes from Jerome Brunet:
These are two simple fixes, yet the first one is quite important as it
solves boots hangs we've been having when FDIV2 gets disabled. This did
not show up before because this particular clock is heavily used and
only gets disabled for a very short period of time before modules (such
as ethernet or emmc) probe.
- fix boot issue with gxbb and gxl platforms
- fix racalculation error in the clk_audio_divider
* tag 'meson-clk-fixes-4.18-1' of https://github.com/BayLibre/clk-meson:
clk: meson: audio-divider is one based
clk: meson-gxbb: set fclk_div2 as CLK_IS_CRITICAL
On some systems, we come out of the bootloader with some
gates set with the clock "enabled" but the reset also
asserted.
Since 8a53fc511c "clk: aspeed: Prevent reset if clock is enabled"
we check that enabled bit in aspeed_clk_enabled(), and do
nothing if already set.
This breaks when the above scenario occurs, as the clock
is enabled, but the reset still needs to be lifted.
This patch fixes it by also checking the reset bit (if any)
and treating a gate in "reset" as being disabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes: 8a53fc511c "clk: aspeed: Prevent reset if clock is enabled"
Cc: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The last-minute fold-in of the ENTRY() macro did change behavior:
instead of printing the symbolic name (e.g. "CLK_IS_BASIC"), it prints
the expansion of it (e.g. "(1UL << (5))").
Use "#" instead of __stringify() to fix this.
Fixes: a6059ab981 ("clk: Show symbolic clock flags in debugfs")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We want to use the ti-aemif platform driver for da830-evm. To make it
work we need a lookup entry for the aemif clock.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: David Lechner <david@lechnology.com>
We want to be able to get the clock both from the board file by its
con_id and from the aemif driver by dev_id.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: David Lechner <david@lechnology.com>
We want to be able to get the clock both from the board file by its
con_id and from the aemif driver by dev_id.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: David Lechner <david@lechnology.com>
We want to be able to get the clock both from the board file by its
con_id and from the aemif driver by dev_id.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: David Lechner <david@lechnology.com>
Since commit a8e3923ab5 ("mtd: rawnand: davinci: don't acquire and
enable clock") we no longer acquire the aemif clock from the davinci
nand driver - we only do it from the ti-aemif driver. Remove the nand
entry from the psc lookup table.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: David Lechner <david@lechnology.com>
Add the clock tree definition for the new px30 SoC.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The new Rockchip socs have optional half divider:
The formula is shown as:
freq_out = 2*freq_in / (2*div + 3)
Is this the same for all of new SoCs.
So we use "branch_half_divider" + "COMPOSITE_NOMUX_HALFDIV \
DIV_HALF \ COMPOSITE_HALFDIV \ CMPOSITE_NOGATE_HALFDIV"
to hook that special divider clock-type into our clock-tree.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are certain clocks which needs to be always enabled for system
operation. Add support for the same by adding 'CLK_IS_CRITICAL' flag
for such clocks.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
q/dl datasheets list the 5th selection value for ck01_sel as
video_27M_clk_root.
By replacing the dummy value we then can set IMX6QDL_CLK_VIDEO_27M
as parent for IMX6QDL_CLK_CKO1_SEL.
Signed-off-by: Philipp Puschmann <pp@emlix.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6UL has GPIO clock gates in CCM CCGR,
add them into clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
IPG clock has no clock gate and its parent AHB clock
is busy divider type, so no need to add CLK_IS_CRITICAL
flag for IPG clock.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
IPG clock has no clock gate and its parent AHB clock
is busy divider type, so no need to add CLK_IS_CRITICAL
flag for IPG clock.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds prepare/unprepare/is_prepared functionality to the drivers for
the SI544 and SI514 chips, allowing the clock output to be disabled when
the clock is not in use.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As claiming Allwinner A64 SRAM C is a prerequisite for all sub-blocks of
the A64 DE2, not only the CCU sub-block, a bus driver is then written for
enabling the access to the whole DE2 part by claiming the SRAM.
In this situation, the A64 compatible string will be just added with no
other requirments, as they're processed by the parent bus driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Here are a couple of typo fixes for clk-davinci for 4.18.
Technically, there are not any users of clk-davinci yet in 4.18, so this can
wait until 4.19 if that is easier.
Signed-off-by: David Lechner <david@lechnology.com>
-----BEGIN PGP SIGNATURE-----
iQJJBAABCgAzFiEEinPYKmofUJkH83OIH4r4jIL3fAMFAlsxe+AVHGRhdmlkQGxl
Y2hub2xvZ3kuY29tAAoJEB+K+IyC93wDHQcP/0UHP3GV4jwyqcZmWQv/448wWooQ
LjwlBSe551Y0smgRS5Xv9D6PCyedMKwvjG+45A9CSNb8EiNWqN8gjEJDSoap7lrH
+haxoffFFp2EXtCH/GIbZeZrv+Z5hGWLSn3ysO/xn0Ly2URpLi6L3VqPybB6f+jm
2cnxBHYjdBAonyrN00nK1xX8LVGHy26IZMeR/Ooxrp3lznQ9YgDpRSmJHVSlnQvc
6HGFt4OhQMu7VAt6xHsiZ2Jv3KZ8hKiM8SIkX3hXMoNqMhjzXcNEEshyGd9nlegj
uqTgH7I8bhHuk68+hcJXj5UrLKwDsg+XKltHlqi1a2FskAw1LZhXNYUAyghdfHkm
szY2JkLdHIhQoyhI+ammfKKoFot91LgOL93ZH+RFlJ7+wFxJA+gxE5pdLiot+vw4
EB7A0vQT/86mxsIv+uFK8B6qMnQeIRd+EK+zfYaEzvlZRGda3cdEggc+nZLASiUL
Zz4P1IC1OgDVq5gcIulA1EA5kKUU4COUWablMlygg9ndnvNeUTd8UrO4y3wZZHvQ
yCPn5NbE41WkpffiGavNZNw3/kFR47dY/DLVwcGQRuzcBstj/I3KUaiMfqgyV6oJ
ei3Ph2aXBHtjj20ejmwuz/46RQSxdzVN6CTL+E5W5zbvMM19pOEGNHnQagWhboxT
LC8qrS0W7kcnN9Nh
=kXdQ
-----END PGP SIGNATURE-----
Merge tag 'clk-davinci-fixes-4.18' of https://github.com/dlech/linux into clk-fixes
Pull davinci clk fixes for 4.18 from David Lechner:
Here are a couple of typo fixes for clk-davinci for 4.18.
* tag 'clk-davinci-fixes-4.18' of https://github.com/dlech/linux:
clk: davinci: fix a typo (which leads to build failures)
clk: davinci: cfgchip: testing the wrong variable
Video PLLs need to be referenced in R40 DT as possible HDMI PHY parent.
Export them.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Display related peripherals need precise clocks to operate correctly.
Allow DE2, TCONs and HDMI to set parent clock.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
According to documentation and experience with other similar SoCs, video
PLLs don't work stable if their output frequency is set below 192 MHz.
Because of that, set minimal rate to both R40 video PLLs to 192 MHz.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This should have been DM365, not DM356.
Fixes: 4eff0bebf4 ("clk: davinci: Fix link errors when not all SoCs are enabled")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David Lechner <david@lechnology.com>
There is a copy and paste bug here. We should be testing "usb1" instead
of "usb0".
Fixes: 58e1e2d2cd ("clk: davinci: cfgchip: Add TI DA8XX USB PHY clocks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Lechner <david@lechnology.com>
This provides a clock driver for the Renesas R09A06G032.
This uses a structure derived from both the R-Car Gen2 driver as well as
the renesas-cpg-mssr driver.
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We had commit 06e226c7fb ("clk: sunxi-ng: Move all clock types to a
library") and commit 799c434154 ("kbuild: thin archives make default
for all archs") in the same development cycle, from different trees.
With migration to the thin archive, the entire drivers/clk/sunxi-ng/lib.a
is linked to the vmlinux. This does not break build, but we do not get
any size saving.
However, we do not need to go back to the individual Kconfig options.
The default configuration pulls in all (or most) of the CCU parts anyway.
Also, once we enable CONFIG_LD_DEAD_CODE_DATA_ELIMINATION, we can simply
list all files with obj-y, and the linker will drop all unused functions
by itself.
After the long discussion [1], people there agreed to fix this, but
nobody sent a patch after all. I am doing it now.
I lifted up CONFIG_SUNXI_CCU to drivers/clk/Makefile because everything
in drivers/clk/sunxi-ng/ depends on SUNXI_CCU.
[1] https://patchwork.kernel.org/patch/9796521/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The audio divider is one based. This offset was mistakenly dropped from
recalc_rate() when migrating to clk_regmap.
Fixes: 88a4e12836 ("clk: meson: migrate the audio divider clock to clk_regmap")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the possibility to apply and query the clock signal duty cycle ratio.
This is useful when the duty cycle of the clock signal depends on some
other parameters controlled by the clock framework.
For example, the duty cycle of a divider may depends on the raw divider
setting (ratio = N / div) , which is controlled by the CCF. In such case,
going through the pwm framework to control the duty cycle ratio of this
clock would be a burden.
A clock provider is not required to implement the operation to set and get
the duty cycle. If it does not implement .get_duty_cycle(), the ratio is
assumed to be 50%.
This change also adds a new flag, CLK_DUTY_CYCLE_PARENT. This flag should
be used to indicate that a clock, such as gates and muxes, may inherit
the duty cycle ratio of its parent clock. If a clock does not provide a
get_duty_cycle() callback and has CLK_DUTY_CYCLE_PARENT, then the call
will be directly forwarded to its parent clock, if any. For
set_duty_cycle(), the clock should also have CLK_SET_RATE_PARENT for the
call to be forwarded
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180619144141.8506-1-jbrunet@baylibre.com
CLK_SET_RATE_GATE should prevent any operation which may result in a rate
change or glitch while the clock is prepared/enabled.
IOW, the following sequence is not allowed anymore with CLK_SET_RATE_GATE:
* clk_get()
* clk_prepare_enable()
* clk_get_rate()
* clk_set_rate()
At the moment this is enforced on the leaf clock of the operation, not
along the tree. This problematic because, if a PLL has the CLK_RATE_GATE,
it won't be enforced if the clk_set_rate() is called on its child clocks.
Using clock rate protection, we can now enforce CLK_SET_RATE_GATE along the
clock tree
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180619134051.16726-3-jbrunet@baylibre.com
the mmci driver (drivers/mmc/host/mmci.c) does the following sequence:
* clk_prepare_enable()
* clk_set_rate()
on SDCx_clk which is a children of SDCx_src. SDCx_src has
CLK_SET_RATE_GATE so this sequence should not be allowed but this was not
enforced. IOW, the flag is ignored. Dropping the flag won't change
anything to the current behaviour of the platform.
CLK_SET_RATE_GATE is being fixed and enforced now. If the flag was kept,
the mmci driver would receive -EBUSY when calling clk_set_rate()
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180619134051.16726-2-jbrunet@baylibre.com
On Amlogic Meson GXBB & GXL platforms, the SCPI Cortex-M4 Co-Processor
seems to be dependent on the FCLK_DIV2 to be operationnal.
The issue occurred since v4.17-rc1 by freezing the kernel boot when
the 'schedutil' cpufreq governor was selected as default :
[ 12.071837] scpi_protocol scpi: SCP Protocol 0.0 Firmware 0.0.0 version
domain-0 init dvfs: 4
[ 12.087757] hctosys: unable to open rtc device (rtc0)
[ 12.087907] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 12.102241] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
But when disabling the MMC driver, the boot finished but cpufreq failed to
change the CPU frequency :
[ 12.153045] cpufreq: __target_index: Failed to change cpu frequency: -5
A bisect between v4.16 and v4.16-rc1 gave
05f814402d ("clk: meson: add fdiv clock gates") to be the first bad commit.
This commit added support for the missing clock gates before the fixed PLL
fixed dividers (FCLK_DIVx) and the clock framework basically disabled
all the unused fixed dividers, thus disabled a critical clock path for
the SCPI Co-Processor.
This patch simply sets the FCLK_DIV2 gate as critical to ensure
nobody can disable it.
Fixes: 05f814402d ("clk: meson: add fdiv clock gates")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[few corrections in the commit description]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This patch adds the clock used by the CryptoCell 630p instance in the
SoC.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the CR core clock, which is used by the Secure Engine (SCEG).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Gilad Ben-Yossef <gilad@benyossef.com>
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked if the produced result is valid, removing a few
false-positives.
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
general cleanups, but nothing too major. The majority of the diff goes to
two SoCs, Actions Semi and Qualcomm. A brand new driver is introduced for
Actions Semi so it takes up some lines to add all the different types, and
the Qualcomm diff is there because we add support for two SoCs and it's quite
a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic platforms. And
then the long tail of driver updates for various fixes and stuff follows
after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock
-----BEGIN PGP SIGNATURE-----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=KK/v
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time we have a good set of changes to the core framework that do
some general cleanups, but nothing too major. The majority of the diff
goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
introduced for Actions Semi so it takes up some lines to add all the
different types, and the Qualcomm diff is there because we add support
for two SoCs and it's quite a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic
platforms. And then the long tail of driver updates for various fixes
and stuff follows after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
clk: qcom: Export clk_fabia_pll_configure()
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
clk-si544: Properly round requested frequency to nearest match
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
clk: use match_string() helper
clk: bcm2835: use match_string() helper
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
clk: imx6: add EPIT clock support
clk: mvebu: use correct bit for 98DX3236 NAND
...
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=/3L8
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"This adds the new overflow checking helpers and adds them to the
2-factor argument allocators. And this adds the saturating size
helpers and does a treewide replacement for the struct_size() usage.
Additionally this adds the overflow testing modules to make sure
everything works.
I'm still working on the treewide replacements for allocators with
"simple" multiplied arguments:
*alloc(a * b, ...) -> *alloc_array(a, b, ...)
and
*zalloc(a * b, ...) -> *calloc(a, b, ...)
as well as the more complex cases, but that's separable from this
portion of the series. I expect to have the rest sent before -rc1
closes; there are a lot of messy cases to clean up.
Summary:
- Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)"
* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use struct_size() for devm_kmalloc() and friends
treewide: Use struct_size() for vmalloc()-family
treewide: Use struct_size() for kmalloc()-family
device: Use overflow helpers for devm_kmalloc()
mm: Use overflow helpers in kvmalloc()
mm: Use overflow helpers in kmalloc_array*()
test_overflow: Add memory allocation overflow tests
overflow.h: Add allocation size calculation helpers
test_overflow: Report test failures
test_overflow: macrofy some more, do more tests for free
lib: add runtime test of check_*_overflow functions
compiler.h: enable builtin overflow checkers and add fallback code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=hB2y
-----END PGP SIGNATURE-----
Merge tag 'printk-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Help userspace log daemons to catch up with a flood of messages. They
will get woken after each message even if the console is far behind
and handled by another process.
- Flush printk safe buffers safely even when panic() happens in the
normal context.
- Fix possible va_list reuse when race happened in printk_safe().
- Remove %pCr printf format to prevent sleeping in the atomic context.
- Misc vsprintf code cleanup.
* tag 'printk-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
printk: drop in_nmi check from printk_safe_flush_on_panic()
lib/vsprintf: Remove atomic-unsafe support for %pCr
serial: sh-sci: Stop using printk format %pCr
thermal: bcm2835: Stop using printk format %pCr
clk: renesas: cpg-mssr: Stop using printk format %pCr
printk: fix possible reuse of va_list variable
printk: wake up klogd in vprintk_emit
vsprintf: Tweak pF/pf comment
lib/vsprintf: Mark expected switch fall-through
lib/vsprintf: Replace space with '_' before crng is ready
lib/vsprintf: Deduplicate pointer_string()
lib/vsprintf: Move pointer_string() upper
lib/vsprintf: Make flag_spec global
lib/vsprintf: Make strspec global
lib/vsprintf: Make dec_spec global
lib/test_printf: Mark big constant with UL
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:
// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
Printk format "%pCr" will be removed soon, as clk_get_rate() must not be
called in atomic context.
Replace it by open-coding the operation. This is safe here, as the code
runs in task context.
Link: http://lkml.kernel.org/r/1527845302-12159-2-git-send-email-geert+renesas@glider.be
To: Jia-Ju Bai <baijiaju1990@gmail.com>
To: Jonathan Corbet <corbet@lwn.net>
To: Michael Turquette <mturquette@baylibre.com>
To: Stephen Boyd <sboyd@kernel.org>
To: Zhang Rui <rui.zhang@intel.com>
To: Eduardo Valentin <edubezval@gmail.com>
To: Eric Anholt <eric@anholt.net>
To: Stefan Wahren <stefan.wahren@i2se.com>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-doc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
* clk-qcom-sdm845:
clk: qcom: Export clk_fabia_pll_configure()
clk: qcom: Add video clock controller driver for SDM845
dt-bindings: clock: Introduce QCOM Video clock bindings
clk: qcom: Add Global Clock controller (GCC) driver for SDM845
clk: qcom: Add DT bindings for SDM845 gcc clock controller
clk: qcom: Configure the RCGs to a safe source as needed
clk: qcom: Add support for BRANCH_HALT_SKIP flag for branch clocks
clk: qcom: Simplify gdsc status checking logic
clk: qcom: gdsc: Add support to poll CFG register to check GDSC state
clk: qcom: gdsc: Add support to poll for higher timeout value
clk: qcom: gdsc: Add support to reset AON and block reset logic
clk: qcom: Add support for controlling Fabia PLL
clk: qcom: Clear hardware clock control bit of RCG
Also fixup the Kconfig mess where SDM845 GCC has msm8998 in the
description and also the video Kconfig says things slightly differently
from the GCC one so just make it the same.
* clk-match-string:
clk: use match_string() helper
clk: bcm2835: use match_string() helper
* clk-ingenic:
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
* clk-si544-round-fix:
clk-si544: Properly round requested frequency to nearest match
* clk-bcm-stingray:
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
* clk-imx7d:
clk: imx7d: reset parent for mipi csi root
clk: imx7d: fix mipi dphy div parent
* clk-hisi-stub:
clk/driver/hisi: Consolidate the Kconfig for the CLOCK_STUB
* clk-mvebu:
clk: mvebu: use correct bit for 98DX3236 NAND
* clk-imx6-epit:
clk: imx6: add EPIT clock support
* clk-debugfs-simple:
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
* clk-qcom-rpmh:
dt-bindings: clock: Introduce QCOM RPMh clock bindings
* clk-npcm7xx:
clk: npcm7xx: fix return value check in npcm7xx_clk_init()
clk: npcm7xx: add clock controller
dt-binding: clk: npcm750: Add binding for Nuvoton NPCM7XX Clock
* clk-of-parent-count:
pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
soc/tegra: pmc: Use of_clk_get_parent_count() instead of open coding
soc: rockchip: power-domain: Use of_clk_get_parent_count() instead of open coding
ARM: timer-sp: Use of_clk_get_parent_count() instead of open coding
clk: Extract OF clock helpers in <linux/of_clk.h>
* clk-qcom-rcg-fix:
clk: qcom: Base rcg parent rate off plan frequency
This is used by the video clk driver on sdm845 and that's a module.
Export it to prevent module build failures.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Update and add Stingray clock definitions and tables so they match the
binding document and the latest ASIC datasheet
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The si544 driver had a rounding problem that using the result of clk_round_rate
may set the clock to yet another rate, for example:
clk_round_rate(195000000) = 194999999
clk_round_rate(194999999) = 194999998
Clients would expect that after clk_set_rate(clk, freq2=clk_round_rate(clk, freq)) the
chip will be running at exactly freq2.
The problem was in the calculation of the feedback divider, it was always rounded
down instead of to the nearest possible VCO value.
After this change, the following holds true for any supported frequency:
actual_freq = clk_round_rate(clk, freq);
clk_set_rate(clk, actual_freq);
clk_round_rate(clk, actual_freq) == actual_freq && clk_get_rate(clk) == actual_freq
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes: 953cc3e811 ("clk: Add driver for the si544 clock generator chip")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is required, as we must not use the AHB1 bus before it is stable.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This was broken before, because the AHB1 bus was enabled before the VPU
clock was ungated, while it must be done afterwards.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When the main processor goes idle, by default its clock is stopped.
However, this also stops the clock of the co-processor.
Here, if the C1CLK clock is enabled, we disable this functionality.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We now have the means to express the specificities of the OTG clock with
the common CGU code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some clocks need a small delay after being ungated to run stable, as
using them too soon might result in hardware lockups.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Support the clocks which are gated when their gate bit is cleared
instead of set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
match_string() returns the index of an array for a matching string,
which can be used instead of open coded variant.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Jerome Brunet