temp and vin status register values may be set by chip specifications, set
again by bios, or by this previously loaded driver. Debug output nicely
displays modprobe init=\d actions.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver handles 3 logical devices in fixed length array. Give this a
define-d constant.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds temp-min/max/crit/fault-alarm callbacks, sensor-device-attribute
declarations, and refs to those new decls in the macro used to initialize
the temp_group (of sysfs files)
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds vin-min/max-alarm callbacks, sensor-device-attribute declarations,
and refs to those new decls in the macro used to initialize the vin_group
(of sysfs files)
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring hwmon/pc87360 into agreement with
Documentation/hwmon/sysfs-interface.
Patchset adds separate limit alarms for voltages and temps, it also adds
temp[123]_fault files. On my Soekris, temps 1,2 are unused/unconnected,
so temp[123]_fault = 1,1,0 respectively. This agrees with
/usr/bin/sensors, which has always shown them as OPEN. Temps 4,5,6 are
thermistor based, and dont have a fault bit in their status register.
This patch:
2 different kinds of constants added:
- CHAN_ALM_* constants for (later) vin, temp alarm callbacks.
- CHAN_* conversion constants, used in _init_device, partly for RW1C bits
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When debugging is enabled, the adm1026 driver currently logs the
message "Setting VID from GPIO11-15" 108 times each time you run
"sensors". Once should be enough.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
* Add missing new-line to one debug message.
* Remove leading colon from 3 debug messages.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
This is my patch for testing correct values of fan div in adm1029 and
prevent a division by 0 for some (unlikely) register values.
Signed-off-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch modifies the w83781d driver to use new style driver binding.
Substantial code modifications are required to deal with the new
interface, especially legacy device detection.
[JD: largely edited to make the patch smaller and to get the driver
to work again on ISA devices.]
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the w83781d driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Probing the ISA bus on systems without ISA bus may hang the system.
This patch makes the ISA bus related code depend on the kernel
configuration parameter CONFIG_ISA. It moves ISA bus related code
into one #ifdef CONFIG_ISA ... #endif block and adds some helper
function.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The W83781D and W83782D can be accessed either on the I2C bus or the
ISA bus. We must not access the same chip through both interfaces. So
far we were relying on the user passing the correct ignore parameter
to skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the w83781d
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Add support to set target temperature and tolerance for thermal
cruise mode.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for pwm_enable.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add PWM manual control.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pins fan/pwm 4-5 can be in use as GPIO. If that is the case, do not
create their sysfs-interface.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.
Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The new-style lm78 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the lm78 driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 detection is relatively weak, and sometimes recent Winbond
chips can be misdetected as an LM78. We have had repeated reports of
this happening. We have an explicit check against this for the ISA
access, do the same for I2C access now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 and LM79 can be accessed either on the I2C bus or the ISA
bus. We must not access the same chip through both interfaces. So far
we were relying on the user passing the correct ignore parameter to
skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the lm78
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.
Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource make the request
(and thus the detection) fail.
This is the exact same fix that was applied to driver w83781d in
March 2008 to address the same problem:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=2961cb22ef02850d90e7a12c28a14d74e327df8d
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Label names ERROR1 and ERROR3 aren't exactly explicit. Change them for
better names that indicate what we are up to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Function RANGE_TO_REG can easily be simplified. Credits go to Herbert
Poetzl for indirectly suggesting this to me. I tested that the new
implementation returns the same result as the original implementation
for all input values.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The new-style lm85 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The Analog Devices and SMSC devices supported by the lm85 driver do
not have the same PWM frequency table as the National Semiconductor
devices. Add support for per-device frequency tables.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The LM85 and compatible chips only support 8 arbitrary PWM frequencies.
The algorithm to pick one of them based on the user input is not
optimum. Improve it to always pick the closest supported frequency.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Rework the device detection to make it clearer and faster in the
general case (when a known device is found.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Simplify the IRQ handling routine of ams driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use a separate mutex to serialize input device creation/removal,
otheriwse we deadlock if we try to remove input device while it is
being polled. Also do not take ams_info.lock when it is not needed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We should not allow writes to the 'joystick' module parameters since
writing there will not trigger creation of the input device. Disable
writes since we provide alternative way of enabling input device via
AMS device's sysfs attribute.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy i2c binding model is phasing out, so the ams driver needs
to be converted to a new-style i2c driver. Here is a naive approach of
this conversion. Basically it is moving the i2c device creation from
the ams driver to the i2c-powermac driver. This should work, but I
suspect we could come up with something cleaner by declaring the i2c
device as part of the platform setup. This could be done later by
someone more familiar with openfirmware-based platforms than I am
myself.
One nice thing brought by this conversion is that the ams driver
should be loaded automatically on systems where is is needed (at
least when the I2C interface to the chip is used) providing
coldplug-aware user-space environment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lm87 driver normally assumes that firmware configured the chip
correctly. Since this is not always the case, alllow platform code to
set the channel register value via platform_data. All other
configuration registers can be changed after driver initialisation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This means that if we have to start the monitor when probed, we also
stop it on removal.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
lm87_init_client() conditionally sets the Start bit and clears the
INT#_Clear bit in the Config 1 register. The condition should be that
either of these bits needs changing, but currently it checks the
(self-clearing) Initialization bit instead of INT#_Clear.
Fix the condition and also ensure we never set the Initialization bit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Degrade the "Unsupported chip" message from info to debug level.
There's nothing wrong with this, so no need to bother the user.
Also make the message slightly more descriptive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The encoding of temperatures varies between chips and modes. So do not
use "temp1" or "temp2" in the names of the conversion functions, but
specify the encoding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC. Adjust the
register conversion functions accordingly.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Use static functions instead of the TEMPx_FROM_REG* and TEMPx_TO_REG*
macros. This will ensure type safety and eliminate any side effects
from arguments passed in since the macros referenced 'val' multiple
times. This change should not affect functionality.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
The Maxim chips supported by the lm90 driver have 8-bit high and low
remote limit values, not 11-bit as the other chips have. So stop reading
from and writing to registers that do not exist on these chips. Also
round the limit values set by the user properly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
The Maxim MAX6657, MAX6658 and MAX6659 have extra resolution bits for
the local temperature measurement. Let the lm90 driver read them and
export them to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
Move the code which aggregates two 8-bit register values into a 16-bit
value to a separate function. We'll need to do it a second time soon and
I don't want to duplicate the code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (158 commits)
powerpc: Fix CHRP PCI config access for indirect_pci
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
powerpc: Fix 32-bit SMP boot on CHRP
powerpc: Fix link errors on 32-bit machines using legacy DMA
powerpc/pci: Improve detection of unassigned bridge resources
hvc_console: Fix free_irq in spinlocked section
powerpc: Get USE_STRICT_MM_TYPECHECKS working again
powerpc: Reflect the used arguments in machine_init() prototype
powerpc: Fix DMA offset for non-coherent DMA
powerpc: fix fsl_upm nand driver modular build
powerpc/83xx: add NAND support for the MPC8360E-RDK boards
powerpc: FPGA support for GE Fanuc SBC610
i2c: MPC8349E-mITX Power Management and GPIO expander driver
powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree
powerpc: document the "fsl,ssi-dma-channel" compatible property
powerpc: disable CHRP and PMAC support in various defconfigs
OF: add fsl,mcu-mpc8349emitx to the exception list
powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
powerpc: remove support for bootmem-allocated memory for the DIU driver
powerpc: remove non-dependent load fsl_booke PTE_64BIT
...
The new-style dme1737 driver implements the optional detect() callback
to cover the use cases of the legacy driver. I don't actually expect
any new-style device for that driver, but as the old i2c API is going
away soon, we have to switch to the new one.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
The dme1737 driver support both LPC (ISA) and SMBus devices. At the
moment it's rather i2c-centric, and LPC variants use a fake i2c_client
for some operations.
In a near future, i2c_client will be allocated by i2c-core rather than
by the device drivers, so non-i2c drivers will not have one. As a
preparation step, change the driver code to no longer assume that
an i2c_client structure is always available. No functional change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
Enable driver checking of the DMI product name (when enabled) on
an Abit AT8 32X, instead of falling back to a manual probe. This
eliminates false negatives and eventually will help avoid
unnecessary bus probes on unsupported mainboards.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The table for the Abit AT8 32X was incorrectly missing an entry
for the sixth ("AUX3") fan. Add this entry, exporting the fan
reading to userspace.
Closes lm-sensors.org ticket #2339.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
On the Shuttle SN68PT, FAN_CTL2 is apparently not connected to a fan,
but to something else. One user has reported instant system power-off
when changing the PWM2 duty cycle, so we disable it.
I use the board name string as the trigger in case the same board is
ever used in other systems.
This closes lm-sensors ticket #2349:
pwmconfig causes a hard poweroff
http://www.lm-sensors.org/ticket/2349
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is not generic, and is added here for backward compatibility.
It is made an individual commit here to make it easier for revert
once the sharpsl_pm gets generic enough.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Driver based on corgi_ssp.c and sharpsl_pm.c, previously done by Richard
Purdie and many others.
Now changed to generic HWMON device and expose all the ADC input value
through sysfs.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch makes the needlessly global ad7414_update_device() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The IT8712F v0.9.1 datasheet applies to revisions >= 0x8 (J).
The driver was incorrectly attempting to enable 16-bit fan
readings on rev 0x7 (I) which led to incorrect RPM values.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Tested-by: John Gumb <john.gumb@tandberg.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The atxp1 device detection code has a major logic flaw, fix it. Not
sure how we managed to miss this when the driver was merged...
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Sebastian Witt <se.witt@gmx.net>
This is a PIC16F747 based controller that monitors and consolidates
the hardware access to various fan and temperature values reported by
adr7462 and similar devices behind an I2C bus.
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all AMD K8 have 6 VID pins, contrary to what was assumed in
commit 116d0486bd. This commit broke
support of older CPU models which have only 5 VID pins:
http://bugzilla.kernel.org/show_bug.cgi?id=11329
We need two entries in the hwmon-vid table, one for 5-bit VID models
(K8 revision <= E) and one for 6-bit VID models (K8 revision >= F).
This fixes bug #11329.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Frank Myhr <fmyhr@fhmtech.com>
Tested-by: Jean-Luc Coulon <jean.luc.coulon@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add in the CPUID for Nehalem chips.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, all sensors are read when the energy meter is queried via
sysfs. This introduces a considerable amount of delay and variation in
the sysfs reading, which is not desirable when trying to profile energy
use. Therefore, read only the energy meters when a sysfs query comes in
for them, and don't cache the results so that we always get the latest
reading.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On older machines, probing for a nonexistent AEM interface returned an
IPMI error; when we saw this, we'd stop probing. On the x3650 M2 and
(presumably) later, we are returned a value indicating success and a
buffer full of garbage or zeroes. This causes the probe function to run
in an infinite loop. To fix this, we add one last check--if the
interface number we're looking for is higher than the number of
interfaces that AEM claims to have, stop probing.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor documentation update to reflect the current full name of the power
management hardware interface and reflows the text a bit.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously the driver was only using DMI to prevent smbus probing on
non-Abit motherboards. However, since the manual probing method is
brittle and prone to failure on some Abit motherboards (esp. the Abit
IP35 Pro) it is better to use DMI to also read the board name and then
decide whether or not to probe the bus.
At the moment, we do not have a list of valid DMI name strings to use
for existing and supported motherboards. This patch only implements DMI
probing for the IP35 Pro. For motherboards that can not yet use DMI
probing, a warning will be printed to the kernel log asking those users
to email me their dmidecode output.
The existing manual probing mechanism will be used if CONFIG_DMI is not
enabled, if DMI probing fails (for DMI-unsupported motherboards), or if
DMI probing fails and the "force" option is set (for DMI-supported
motherboards). Ideally in the longer term this manual probing method
would be removed.
This patch should be safe to apply as it does not change the probing
behaviour for most of the supported motherboards, just the IP35 Pro,
which already has regressions filed against it in 2.6.26.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11212
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the sensor -> channel/dimm mapping in tempX_label.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPI driver for analog to digital converters national semiconductor
ADC081S101, ADC124S501, ...
Code for 8 channels by Tobias Himmer.
This driver adds support for National Semiconductor ADC<bb><c>S<sss> chip
family, where:
* bb is the resolution in number of bits (8, 10, 12)
* c is the number of channels (1, 2, 4, 8)
* sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
kSPS and 101 for 1 MSPS)
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Cc: Tobias Himmer <tobias@himmer-online.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for Macbook v3 (sensors and accelerometer).
Signed-off-by: Nicolas Boichat <nicolas@boichat.ch>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for fans and temperature sensors on intel iMac.
Tested on iMac 24" 2.8ghz (iMac8,1), it supports the following sensors:
cpu A
ambient
gpu
gpu diode
gpu heatsink
hd bay 1
memory controller
optical drive
power
Signed-off-by: Roberto De Ioris <roberto@unbit.it>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop the legacy lm75 driver, and add a detect callback to the
new-style driver to achieve the same functionality.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
The it8705 chip supports 16-bit fan tachometers in revisions at least
>= 0x03 (Version G). This patch enables 16-bit fan readings on all
revisions >= 0x03 just like the it8712, it8716, and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it8712 chip supports 16-bit fan tachometers in revisions >= 0x07.
Revisions >= 0x08 dropped support for 8-bit fan divisor registers. The
patch enables 16-bit fan readings on all revisions >= 0x07 just like
the it8716 and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
AMD NPT 0Fh cpus use 6 bit VID codes. Successive codes with msb 0
describe 25mV decrements, while those with msb 1 describe 12.5mV
decrements. Existing hwmon-vid.c is correct only for codes with msb 0;
add support for the codes with msb 1.
Ref:
p 309, Table 71
AMD Publication 32559, BIOS and Kernel Developer's Guide for AMD NPT Family 0Fh Processors
http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/32559.pdf
Signed-off-by: Frank Myhr <fmyhr@fhmtech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Driver for the Analog Devices AD7414 temperature monitoring chip.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add critical temperature limits to the driver. These limits are read
only.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The adm9240 driver is in the kernel for three years now, time to
remove the EXPERIMENTAL dependency.
Signed-off-by: Grant Coady <gcoady.lk@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Drop the reset parameter of the w83627hf driver. It seems it wasn't
that useful. It was dropped from the Linux 2.4 version of this driver
back in July 2004.
The only users who have reported that they were still using this
parameter, needed it to switch the chip from automatic fan speed
control back to manual mode. Now that the driver creates pwmN_enable
sysfs files, users will be able to use these files instead, which is
way less agressive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dominik Geyer <dominik.geyer@gmx.de>
Adds support for pwm_enable sysfs interface for the w83627hf driver.
Signed-off-by: Dominik Geyer <dominik.geyer@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update w83791d with fan bits in vbat mon register (7.48 of the
datasheet). This change allows all fans to have a divisor of 128,
and fixes a problem with incorrectly reported fan speeds.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
These functions aren't used before being defined, so there's no point
in forward-declaring them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Add support for the SCH5027. The differences to the DME1737 are:
- No support for programmable temp offsets
- In auto mode, PWM outputs stay on min value if temp goes below low threshold
and can't be programmed to fully turn off
- Different voltage scaling
- No VID input
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Skip the checking of the device ID register in the hwmon register
block if the force_id option is used.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix names of attribute structs to make them more consistent with the
rest of the code. Minor comment changes.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Clean up and simplify the device initialization function:
* Degrade error messages to warnings - what they really are.
* Stop warning about VxI mode, we don't really care.
* Drop comment about lack of limit initialization - that's the standard
way, all hardware monitoring drivers do that.
* Only read the configuration register once.
* Only write back to the configuration register if needed.
* Don't attempt to clear the lock bit, it locks itself to 1.
* Move the function to before it's called, so that we no longer need to
forware declare it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Misc cleanups to the lm85 hardware monitoring driver:
* Mark constant arrays as const.
* Remove useless masks.
* Have lm85_write_value return void - nobody is checking the returned
value anyway and in some cases it was plain wrong.
* Remove useless initializations.
* Rename new_client to client in lm85_detect.
* Replace cascaded if/else with a switch/case in lm85_detect.
* Group similar loops in lm85_update_device.
* Remove legacy comments.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
In set_pwm_auto_pwm_minctl, we write cached register bits back to the
chip. This is a bad idea as we have no guarantee that the cache is
up-to-date. Better read a fresh register value from the chip, it's
safer and in fact it is also more simple.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Drop a lot of useless register defines, conversion macros, data structure
members and update code. All these register values were read from the
device but nothing is done out of them, so this is all dead code in
practice.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix most style issues reported by checkpatch, including:
* Trailing, missing and extra whitespace
* Extra parentheses, curly braces and semi-colons
* Broken indentation
* Lines too long
I verified that the generated code is the same before and after
these changes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
More LM75 updates:
- Teach the LM75 driver to use new-style driver binding:
* Create a second driver struct, using new-style driver binding
methods cribbed from the legacy code.
* Add a MODULE_DEVICE_TABLE (for "newER-style binding")
* The legacy probe logic delegates its work to this new code.
* The legacy driver now uses the name "lm75_legacy".
- More careful initialization. Chips are put into 9-bit mode so
the current interconversion routines will never fail.
- Save the original chip configuration, and restore it on exit.
(Among other things, this normally turns off the mode where
the chip is constantly sampling ... and thus saves power.)
So the new-style code should catch all chips that boards declare,
while the legacy code catches others. This particular coexistence
strategy may need some work yet ... legacy modes might best be set
up explicitly by some tool not unlike "sensors-detect". (Or else
completely eradicated...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Minor cleanup and reorg of the lm75 code.
- Kconfig provides a larger list of lm75-compatible chips
- A top comment now says what the driver does (!) ... as in, just
what sort of sensor is this??
- Section comments now delineate the various sections of the driver:
hwmon attributes, driver binding, register access, module glue.
One driver binding function moved out of the attribute section,
as did the driver struct itself.
- Minor tweaks to legacy probe logic: correct a comment, and
remove a pointless variable.
- Whitespace, linelength, and comment fixes.
This patch should include no functional changes. It's preparation
for adding new-style (driver model) I2C driver binding.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
All the *_MAX_ADDR defines are never used, so remove them. The number
of registers of each type is already expressed by the *_COUNT defines.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch fixes a voltage scaling issue for the sch311x device.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds a module load parameter to enable probing of
non-standard LPC addresses 0x162e and 0x164e when scanning for supported
ISA chips.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch gets rid of a couple of macros previously used for sysfs attribute
generation and manipulation. This makes the source a little bigger but a lot
more readable and maintainable. It also fixes an issue with pwm5 & pwm6
attributes not being created read-only initially.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new-style w83l786ng driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Kevin Lo <kevlo@kevlo.org>
The new-style w83l785ts driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style w83793 driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style w83792d driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style w83791d driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
The new-style thmc50 driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
The new-style smsc47m192 driver implements the optional detect()
callback to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hartmut Rick <linux@rick.claranet.de>
The new-style max6650 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans J. Koch <hjk@linutronix.de>
The new-style max1619 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alexey Fisher <fishor@mail.ru>
The new-style lm93 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Eric J. Bowersox <ericb@aspsys.com>
Cc: Carsten Emde <cbe@osadl.org>
Cc: Hans J. Koch <hjk@linutronix.de>
The new-style lm92 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style lm90 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style lm87 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
The new-style lm83 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style lm80 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style lm77 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andras Bali <drewie@freemail.hu>
The new-style lm63 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style gl520sm driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Maarten Deprez <maartendeprez@users.sourceforge.net>
The new-style gl518sm driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style fscpos driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style fschmd driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <j.w.r.degoede@hhs.nl>
The new-style fscher driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Reinhard Nissl <rnissl@gmx.de>
Drop the legacy f75375s i2c driver, and add a detect callback to the
new-style i2c driver to achieve the same functionality.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Riku Voipio <riku.voipio@movial.fi>
The new-style ds1621 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style atxp1 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style asb100 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style adt7473 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
The new-style adt7470 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
The new-style ads7828 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style adm9240 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Grant Coady <gcoady.lk@gmail.com>
The new-style adm1031 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alexandre d'Alton <alex@alexdalton.org>
The new-style adm1029 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
The new-style adm1026 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style adm1025 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new-style adm1021 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The ad7418 driver is only used on embedded platforms where i2c
devices can easily be declared in platform code. Thus a new-style
i2c driver makes perfect sense. This lets us get rid of quirky
detection code (these chips have no identification registers) and
shrinks the binary driver size by 38%.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Adds R61, T61p, X61s, X61, Z61m, Z61p models to whitelist.
Fixes this:
cullen@lenny:~$ sudo modprobe hdaps
FATAL: Error inserting hdaps (/lib/modules/2.6.22-10-generic/kernel/drivers/hwmon/hdaps.ko): No such device
[25192.888000] hdaps: supported laptop not found!
[25192.888000] hdaps: driver init failed (ret=-19)!
Originally based on an Ubuntu patch that got it wrong, the dmidecode
output of the corresponding laptops shows LENOVO as the manufacturer.
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.22/+bug/133636
tested on X61s:
[ 184.893588] hdaps: inverting axis readings.
[ 184.893588] hdaps: LENOVO ThinkPad X61s detected.
[ 184.893588] input: hdaps as /class/input/input12
[ 184.924326] hdaps: driver successfully loaded.
Cc: Klaus S. Madsen <ubuntu@hjernemadsen.org>
Cc: Chuck Short <zulcss@ubuntu.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LM75 sensor reading bugfix: never save error status as valid
sensor output. This could be improved, but at least this
prevents certain rude failure modes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
It has been reported that the abituguru3 driver fails to load after a BIOS
update. This patch fixes this by loosening the detection routine so that it
will work after the BIOS update too. To compensate for the now very loose
detection an additional check is added on the DMI Base Board vendor string to
make sure we only load on Abit motherboards, this is the same as the check in
the abituguru (1 / 2) driver.
Signed-of-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch identifies the Abit AW8D board as such, and adds support for its
aux5 fan connector
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Jim Cromie