Otherwise we can get the following errors occasionally on some devices:
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 14329
...
I have one device that hits this error almost on every boot, and another
one that hits it only rarely with the other ones I've used behave without
problems. I'm not sure if the issue is related to a particular eMMC card
model, but in case it is, both of the machines with issues have:
# cat /sys/class/mmc_host/mmc1/mmc1:0001/manfid \
/sys/class/mmc_host/mmc1/mmc1:0001/oemid \
/sys/class/mmc_host/mmc1/mmc1:0001/name
0x000045
0x0100
SEM16G
and the working ones have:
0x000011
0x0100
016G92
Note that "ti,non-removable" is different as omap_hsmmc_reg_get() does not
call omap_hsmmc_disable_boot_regulators() if no_regulator_off_init is set.
And currently we set no_regulator_off_init only for "ti,non-removable" and
not for "non-removable". It seems that we should have "non-removable" with
some other mmc generic property behave in the same way instead of having to
use a non-generic property. But let's fix the issue first.
Fixes: 7e2f8c0ae6 ("ARM: dts: Add minimal support for motorola droid 4
xt894")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix wrong mode for dts file added by commit bb3e3fbbac
("ARM: dts: Add DT support for Octavo Systems OSD3358-SM-RED
based on TI AM335x").
Signed-off-by: Neeraj Dantu <neeraj.dantu@octavosystems.com>
CC: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When a targetport is removed from the config, fcloop will avoid calling
the LS done() routine thinking the targetport is gone. This leaves the
initiator reset/reconnect hanging as it waits for a status on the
Create_Association LS for the reconnect.
Change the filter in the LS callback path. If tport null (set when
failed validation before "sending to remote port"), be sure to call
done. This was the main bug. But, continue the logic that only calls
done if tport was set but there is no remoteport (e.g. case where
remoteport has been removed, thus host doesn't expect a completion).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In many architectures loads may be reordered with older stores to
different locations. In the nvme driver the following two operations
could be reordered:
- Write shadow doorbell (dbbuf_db) into memory.
- Read EventIdx (dbbuf_ei) from memory.
This can result in a potential race condition between driver and VM host
processing requests (if given virtual NVMe controller has a support for
shadow doorbell). If that occurs, then the NVMe controller may decide to
wait for MMIO doorbell from guest operating system, and guest driver may
decide not to issue MMIO doorbell on any of subsequent commands.
This issue is purely timing-dependent one, so there is no easy way to
reproduce it. Currently the easiest known approach is to run "Oracle IO
Numbers" (orion) that is shipped with Oracle DB:
orion -run advanced -num_large 0 -size_small 8 -type rand -simulate \
concat -write 40 -duration 120 -matrix row -testname nvme_test
Where nvme_test is a .lun file that contains a list of NVMe block
devices to run test against. Limiting number of vCPUs assigned to given
VM instance seems to increase chances for this bug to occur. On test
environment with VM that got 4 NVMe drives and 1 vCPU assigned the
virtual NVMe controller hang could be observed within 10-20 minutes.
That correspond to about 400-500k IO operations processed (or about
100GB of IO read/writes).
Orion tool was used as a validation and set to run in a loop for 36
hours (equivalent of pushing 550M IO operations). No issues were
observed. That suggest that the patch fixes the issue.
Fixes: f9f38e3338 ("nvme: improve performance for virtual NVMe devices")
Signed-off-by: Michal Wnukowski <wnukowski@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
[hch: updated changelog and comment a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently, variable ref_count within the bsg_device struct is of
type atomic_t. For variables being used as reference counters,
the refcount API should be used instead of atomic. The newer
refcount API works to prevent counter overflows and use-after-free
bugs. So, move this varable from the atomic API to refcount,
potentially avoiding the issues mentioned.
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
kmem_cache_destroy() can handle NULL pointer correctly, so there is
no need to check e->icq_cache before calling kmem_cache_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The DMA is broken on this specific device for some unknown
reason (probably badly designed or plain broken interface
electronics) and will only work with PIO. Other users of
the same hardware does not have this problem.
Add a specific quirk so that this Gemini device gets
DMA turned off. Also fix up some code around passing the
port information around in probe while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
when ac/dc switch, driver will be notified by acpi event.
then the power source will be updated. so don't need to
get power source when set power state.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is currently an intermittent hang from a memory leak in
DTN stress testing. It is caused by unfreed memory during driver
disable.
[How]
Do a dc_sink_release in the case that skips it incorrectly.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can't hold the mn_lock while allocating memory.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
when hw_fini/suspend, smu only need to power on uvd block
if uvd pg is supported, don't need to call uvd to do hw_init.
v2: fix typo in patch descriptions and comments.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For SI/Kv, the power state is managed by function
amdgpu_pm_compute_clocks.
when dpm enabled, we should call amdgpu_pm_compute_clocks
to update current power state instand of set boot state.
this change can fix the oops when kfd driver was enabled on Kv.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Forgot to add vce pg support via smu for Kaveri/Mullins.
Fixes: 561a5c83eadd ("drm/amd/pp: Unify powergate_uvd/vce/mmhub
to set_powergating_by_smu")
v2: refine patch descriptions suggested by Michel
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is required by gfx hw and can fix the rlc hang when
do s3 stree test on Cz/St.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Hang Zhou <hang.zhou@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the VM size based on system memory size between the ASIC-specific
limits given by min_vm_size and max_bits. GFXv9 GPUs will keep their
default VM size of 256TB (48 bit). Only older GPUs will adjust VM size
depending on system memory size.
This makes more VM space available for ROCm applications on GFXv8 GPUs
that want to map all available VRAM and system memory in their SVM
address space.
v2:
* Clarify comment
* Round up memory size before >> 30
* Round up automatic vm_size to power of two
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull networking fixes from David Miller:
1) ICE, E1000, IGB, IXGBE, and I40E bug fixes from the Intel folks.
2) Better fix for AB-BA deadlock in packet scheduler code, from Cong
Wang.
3) bpf sockmap fixes (zero sized key handling, etc.) from Daniel
Borkmann.
4) Send zero IPID in TCP resets and SYN-RECV state ACKs, to prevent
attackers using it as a side-channel. From Eric Dumazet.
5) Memory leak in mediatek bluetooth driver, from Gustavo A. R. Silva.
6) Hook up rt->dst.input of ipv6 anycast routes properly, from Hangbin
Liu.
7) hns and hns3 bug fixes from Huazhong Tan.
8) Fix RIF leak in mlxsw driver, from Ido Schimmel.
9) iova range check fix in vhost, from Jason Wang.
10) Fix hang in do_tcp_sendpages() with tls, from John Fastabend.
11) More r8152 chips need to disable RX aggregation, from Kai-Heng Feng.
12) Memory exposure in TCA_U32_SEL handling, from Kees Cook.
13) TCP BBR congestion control fixes from Kevin Yang.
14) hv_netvsc, ignore non-PCI devices, from Stephen Hemminger.
15) qed driver fixes from Tomer Tayar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: sched: Fix memory exposure from short TCA_U32_SEL
qed: fix spelling mistake "comparsion" -> "comparison"
vhost: correctly check the iova range when waking virtqueue
qlge: Fix netdev features configuration.
net: macb: do not disable MDIO bus at open/close time
Revert "net: stmmac: fix build failure due to missing COMMON_CLK dependency"
net: macb: Fix regression breaking non-MDIO fixed-link PHYs
mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge
i40e: fix condition of WARN_ONCE for stat strings
i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled
ixgbe: fix driver behaviour after issuing VFLR
ixgbe: Prevent unsupported configurations with XDP
ixgbe: Replace GFP_ATOMIC with GFP_KERNEL
igb: Replace mdelay() with msleep() in igb_integrated_phy_loopback()
igb: Replace GFP_ATOMIC with GFP_KERNEL in igb_sw_init()
igb: Use an advanced ctx descriptor for launchtime
e1000: ensure to free old tx/rx rings in set_ringparam()
e1000: check on netif_running() before calling e1000_up()
ixgb: use dma_zalloc_coherent instead of allocator/memset
ice: Trivial formatting fixes
...
Commit 49aa76b166 ("mtd: rawnand: do not execute nand_scan_ident()
if maxchips is zero") gave a new meaning for calling nand_scan_ident()
with maxchips=0.
It is a special usage for some drivers such as docg4, but actually
the Denali driver may pass maxchips=0 to nand_scan() when the driver
is enabled but no NAND chip is found on the board for some reasons.
If nand_scan_with_ids() is called with maxchips=0, nand_scan_ident()
is skipped, then nand_set_defaults() is skipped as well. Thus, the
driver must set chip->controller beforehand. Otherwise, nand_attach()
causes NULL pointer dereference.
In fact, the Denali controller knows the number of connected chips
before calling nand_scan_ident(); if DEVICE_RESET fails, there is no
chip in that chip select. Then, denali_reset_banks() sets the maxchips
to the number of detected chips. If no chip is found, maxchips is zero.
In this case, there is no point for calling nand_scan() because we know
it will fail for sure. Let's make the probe function fail immediately.
Fixes: 49aa76b166 ("mtd: rawnand: do not execute nand_scan_ident() if maxchips is zero")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Using only 32-bit writes for the pte will result in an intermediate
L1TF vulnerable PTE. When running as a Xen PV guest this will at once
switch the guest to shadow mode resulting in a loss of performance.
Use arch_atomic64_xchg() instead which will perform the requested
operation atomically with all 64 bits.
Some performance considerations according to:
https://software.intel.com/sites/default/files/managed/ad/dc/Intel-Xeon-Scalable-Processor-throughput-latency.pdf
The main number should be the latency, as there is no tight loop around
native_ptep_get_and_clear().
"lock cmpxchg8b" has a latency of 20 cycles, while "lock xchg" (with a
memory operand) isn't mentioned in that document. "lock xadd" (with xadd
having 3 cycles less latency than xchg) has a latency of 11, so we can
assume a latency of 14 for "lock xchg".
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Pull Xen block driver fixes from Konrad:
"Fix for flushing out persistent pages at a deterministic rate"
* 'stable/for-jens-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/blkback: remove unused pers_gnts_lock from struct xen_blkif_ring
xen/blkback: move persistent grants flags to bool
xen/blkfront: reorder tests in xlblk_init()
xen/blkfront: cleanup stale persistent grants
xen/blkback: don't keep persistent grants too long
We have two potential issues:
1) After commit 2887e41b91, we only wake one process at the time when
we finish an IO. We really want to wake up as many tasks as can
queue IO. Before this commit, we woke up everyone, which could cause
a thundering herd issue.
2) A task can potentially consume two wakeups, causing us to (in
practice) miss a wakeup.
Fix both by providing our own wakeup function, which stops
__wake_up_common() from waking up more tasks if we fail to get a
queueing token. With the strict ordering we have on the wait list, this
wakes the right tasks and the right amount of tasks.
Based on a patch from Jianchao Wang <jianchao.w.wang@oracle.com>.
Tested-by: Agarwal, Anchal <anchalag@amazon.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Prep patch for calling the handler from a different context,
no functional changes in this patch.
Tested-by: Agarwal, Anchal <anchalag@amazon.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
pers_gnts_lock isn't being used anywhere. Remove it.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The struct persistent_gnt flags member is meant to be a bitfield of
different flags. There is only PERSISTENT_GNT_ACTIVE flag left, so
convert it to a bool named "active".
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In case we don't want pv block devices we should not test parameters
for sanity and eventually print out error messages. So test precluding
conditions before checking parameters.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Add a periodic cleanup function to remove old persistent grants which
are no longer in use on the backend side. This avoids starvation in
case there are lots of persistent grants for a device which no longer
is involved in I/O business.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Persistent grants are allocated until a threshold per ring is being
reached. Those grants won't be freed until the ring is being destroyed
meaning there will be resources kept busy which might no longer be
used.
Instead of freeing only persistent grants until the threshold is
reached add a timestamp and remove all persistent grants not having
been in use for a minute.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The email was botched in one entry, and I also forgot to update the
location of the git tree. It'll be under the linux-block umbrella, just
with different branches.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Fixes: 7634ccd2da ("libata: maintainership update")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some cases 32-bit PAE PV guests still write PTEs directly instead of
using hypercalls. This is especially bad when clearing a PTE as this is
done via 32-bit writes which will produce intermediate L1TF attackable
PTEs.
Change the code to use hypercalls instead.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
On Nehalem and newer core CPUs the CPU cache internally uses 44 bits
physical address space. The L1TF workaround is limited by this internal
cache address width, and needs to have one bit free there for the
mitigation to work.
Older client systems report only 36bit physical address space so the range
check decides that L1TF is not mitigated for a 36bit phys/32GB system with
some memory holes.
But since these actually have the larger internal cache width this warning
is bogus because it would only really be needed if the system had more than
43bits of memory.
Add a new internal x86_cache_bits field. Normally it is the same as the
physical bits field reported by CPUID, but for Nehalem and newerforce it to
be at least 44bits.
Change the L1TF memory size warning to use the new cache_bits field to
avoid bogus warnings and remove the bogus comment about memory size.
Fixes: 17dbca1193 ("x86/speculation/l1tf: Add sysfs reporting for l1tf")
Reported-by: George Anchev <studio@anchev.net>
Reported-by: Christopher Snowhill <kode54@gmail.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: x86@kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Michael Hocko <mhocko@suse.com>
Cc: vbabka@suse.cz
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180824170351.34874-1-andi@firstfloor.org
If gcc (e.g. 4.1.2) decides not to inline init_mtd_structs() and
read_id_reg(), this will cause section mismatches, and crashes:
WARNING: drivers/mtd/nand/raw/docg4.o(.text+0xc10): Section mismatch in reference from the function docg4_attach_chip() to the function .init.text:init_mtd_structs()
The function docg4_attach_chip() references
the function __init init_mtd_structs().
This is often because docg4_attach_chip lacks a __init
annotation or the annotation of init_mtd_structs is wrong.
WARNING: drivers/mtd/nand/raw/docg4.o(.text+0xc3e): Section mismatch in reference from the function docg4_attach_chip() to the function .init.text:read_id_reg()
The function docg4_attach_chip() references
the function __init read_id_reg().
This is often because docg4_attach_chip lacks a __init
annotation or the annotation of read_id_reg is wrong.
Fix this by dropping the now incorrect __init annotations from
init_mtd_structs() and read_id_reg().
Fixes: 66a38478dc ("mtd: rawnand: docg4: convert driver to nand_scan()")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
imx6sl-evk, imx6sll-evk and imx6sx-sdb boards use a Seiko 43WVF1G panel.
Now that the DRM mxsfb driver is the one selected by default, let's
also select CONFIG_DRM_PANEL_SEIKO_43WVF1G so that these boards continue
to have a working display by default.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx23-evk and imx28-evk boards use a Seiko 43WVF1G panel.
Now that the DRM mxsfb driver is the one selected by default, let's
also select CONFIG_DRM_PANEL_SEIKO_43WVF1G so that these boards continue
to have a working display by default.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx23-evk board has a Seiko 43WVF1G parallel display.
Instead of hardcoding the display timings in the device tree, use
the "sii,43wvf1g" compatible instead.
This aligns with the new mxsfb bindings scheme documented at:
Documentation/devicetree/bindings/display/mxsfb.txt
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is recommended to place regulators outside simple-bus, so move them
accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx28-evk board has a Seiko 43WVF1G parallel display.
Instead of hardcoding the display timings in the device tree, use
the "sii,43wvf1g" compatible instead.
This aligns with the new mxsfb bindings scheme documented at:
Documentation/devicetree/bindings/display/mxsfb.txt
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is recommended to place regulators outside simple-bus, so move them
accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit 1c86c9dd82.
That commit followed the reference manual but unfortunately the imx7d
manual is incorrect.
Tested with ath9k pcie card and confirmed internally.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 1c86c9dd82 ("ARM: dts: imx7d: Invert legacy PCI irq mapping")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch update some variable name from ovl to comp
Because RDMA would be first HW in ddp, the naming ovl
should be change to comp.
Signed-off-by: Stu Hsieh <stu.hsieh@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
This patch use layer_nr function to get layer number to init plane
When plane init in crtc create,
it use the number of OVL layer to init plane.
That's OVL can read 4 memory address.
For mt2712 third ddp, it use RDMA to read memory.
RDMA can read 1 memory address, so it just init one plane.
For compatibility, this patch use mtk_ddp_comp_layer_nr function
to get layer number from their HW component in ddp for plane init.
Signed-off-by: Stu Hsieh <stu.hsieh@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
This patch add function to return RDMA layer number
RDMA always has one layer.
Signed-off-by: Stu Hsieh <stu.hsieh@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
This patch add function to return OVL layer number
For now, MT8173, MT2712, MT2701 OVL all has 4 layer.
Signed-off-by: Stu Hsieh <stu.hsieh@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
This patch add YUYV/UYVY color format support for RDMA
and transform matrix for YUYV/UYVY.
Signed-off-by: Stu Hsieh <stu.hsieh@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
This patch add the comment about color format setting for OVL
Signed-off-by: Stu Hsieh <stu.hsieh@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Tony Lindgren