The SYSCLK source is automatically managed when configuring the PLL.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the TLV320AIC3x supplies and enables all of them for the
entire lifetime of the device.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Move PLL enable from BIAS_ON state to BIAS_PREPARE to be pair with
BIAS_STANDBY where PLL is disabled. Remove also old comments about power
control.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
These ADC, DAC and output pin power off commands are needless in
aic3x_set_bias_level since they are not enabled in aic3x_init and they are
defined in aic3x_dapm_widgets so the ASoC DAPM will take care of them
anyway.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for Philips UDA1345 CODEC. The CODEC has only
volume control, de-emphasis, mute, DC filtering and power control features.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Delay reporting for the three implemented DAC33 FIFO modes.
DAC33 has FIFO depth status register(s), but it can not be used, since
inside of pcm_pointer we can not send I2C commands.
Timestamp based estimation need to be used. The method of calculating
the delay depends on the active FIFO mode.
Bypass mode: FIFO is bypassed, report 0 as delay
Mode1: nSample fill mode. In this mode I need to use two timestamp
ts1: taken when the interrupt has been received
ts2: taken before writing to nSample register.
Interrupts are coming when DAC33 FIFO depth goes under alarm threshold.
Phase1: when we received the alarm threshold, but our workqueue has
not been executed (safeguard phase). Just count the played out
samples since ts1 and subtract it from the alarm threshold
value.
Phase2: During nSample burst (after writing to nSample register), count
the played out samples since ts1, count the samples received
since ts2 (in a burst). Estimate the FIFO depth using these and
alarm threshold value.
Phase3: Draining phase (after the burst read), count the played out
samples since ts1. Estimate the FIFO depth using the nSample
configuration and the alarm threshold value.
Mode7: Threshold based fill mode. In this mode one timestamp is enough.
ts1: taken when the interrupt has been received
Interrupts are coming when DAC33 FIFO depth reaches upper threshold.
Phase1: Draining phase (after the burst), counting the played out
samples since ts1, and subtract it from the upper threshold
value.
Phase2: During burst operation. Using the pre calculated time needed to
play out samples from the buffer during the drain period (from
upper to lower threshold), move the time window to cover the
estimated time from the burst start to the current time.
Calculate the samples played out since lower threshold and also
the samples received during the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When the DAC33 FIFO is in use the dai interface is running in
much higher speed than the sampling frequency.
Calculate the rate based on the internal base frequency and
the bclk divider.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Upper and Lower threshold values are used as magic
numbers. Replace them with defines for later use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is no need for calculations for FIFO bypass mode.
Just in case set the nsample maximum limit, which
has been done in the calculation phase.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Alarm threshold interrupt is triggered right after the
playback start.
This interrupt is recieved during the first burst period,
and caused the state machine to write additional nSample
command, which has to be avoided.
To fix this issue move the DAC33 interrupt unmasking
after we configured the PREFILL register with a small
delay.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Follow the core jack implementation and allow reporting on the status
of NULL jacks, avoiding the need to check in detection implementations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use all the available Fratio values when configuring the WM8994 FLL, not
just 0 and 3, following more complete characterisation of the device
performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8994 FLL can be clocked from one of four inputs, the two MCLKs and
the LRCLK and BCLK of the AIF associated with the FLL. Allow all four
inputs to be used rather than defaulting to MCLK1.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
An index equal to the array size may not be accessed.
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the features of the multi CODEC work is that it embeds a struct
device in the CODEC to provide diagnostics via a sysfs class rather than
via the device tree, at which point it's much better to use the struct
device private data rather than having two places to store it. Provide
an accessor function to allow this change to be made more easily, and
update all the CODEC drivers are updated.
To ensure use of the accessor the private data structure member is
renamed, meaning that if code developed with older an older core that
still uses private_data is merged it will fail to build.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Doing so causes a deadlock, so just signal the timer to stop
using an atomic variable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the notification of elapsed periods is not very exact.
Increase minimum periods to 4 as suggested by Liam Girdwood.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for sound through the WM8750 codec on Zipit Z2.
Also, this patch incorporates support for detecting headset jack
insertion through the jack detection API.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Register the WM8750 as a SPI or I2C device. This patch mostly shuffles code
around. Hugely inspired by WM8753 which was already converted.
Also, this patch fixes the Jive and Spitz machine.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using a regular timer results in poll times < 1 jiffie with small
buffers, so we loaded the timer with the actual jiffie value. We can
be more accurate using a hrtimer. Also, we have to call
snd_pcm_period_elapsed after playing period_bytes and not
runtime->period_size (which is in samples and not in bytes).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When checking if we are DMA capable we have to check for the
IMX_SSI_DMA flag which is already set from platform_data instead
of setting it again when we want to do DMA.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@Slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Support interrupt based microphone bias detection. The WM8994 has two
microphone bias supplies, with detection supported on both. Detection
using GPIOs together with the standard GPIO based jack framework is
already supported via the platform data for the WM8994 core driver.
Note that as well as the microphone bias itself the system clock and
whichever AIF clock is supplying the system clock will need to be
enabled for detection to function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
[Note that this is a backported version for 2.6.34.
Upstream commit is fd23b7dee]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise we may try to power down multiple times when the using
idle bias off and the driver is removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The DCS_DATAPATH_BUSY bit used to monitor the completion of DC servo
operations has been deprecated and with some more recente revisions
may perform incorrectly, especially when only analogue bypass paths
are in use. Switch to using readback from the DC servo command
register instead, which is supported for all devices. Without this
unacceptably long timeouts may be observed in some circumstances.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If we need to offset correct the DC servo then don't use runtime
recalibration since that is likely to introduce further offsets
which will be evident on powerdown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
More recent Wolfson hubs devices add the ability to read back the DC
servo calibration information from the register used to write offsets,
and later still ones remove the old readback registers. Add support
for the new scheme, and use it for WM8994 device revisions that
support it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the correction wraps around then a substantial offset would be
introduced.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
With recent (2.6.34) chnages in PCM handling, capture stopped working on my
OMAP1510 based Amstrad Delta videophone.
Using 2.6.34-rc2, I was able to correct the problem in 3 different ways:
1. reverting commit 7b3a177b0d,
2. enabling additional jiffies check with
echo 4 >/proc/asound/card0/pcm0c0/xrun_debug
3. applying the patch below.
Since I wasn't able to reproduce the problem on my i686 PC, I guess the
problem is probably machine specific.
The patch reuses the method for software emulation of missing hardware
pointer, already implemented for playback on OMAP1510. It's possible that
event if a hardware pointer is available for capture on this machine, its
behaviour may be not compatible with what upper layer expects.
If you think the problem may be more general and should be solved differently,
on a higher level, I can try to work more on it if you give me a hint.
If the patch gets accepted, I suggest it goes as a fix in the current release
cycle.
Created and tested against linux-2.6.34-rc2.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The way i've factored out the bus probe and removal functions so
that there's no code in the individual I2C and SPI functions means
that the register() and unregister() functions could just be squashed
into the bus_probe() and bus_remove() functions.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[The issue is an attempt to write the pdata without the AC97 device
allocated when using ac97.c - also added a comment in soc-core.c for the
special case for ac97. -- broonie]
Signed-off-by: Graham Gower <graham.gower@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown