phy-sun4i-usb now has proper dr_mode handling, it always registers an
extcon, and sends a notify with the mode (even when in peripheral- /
host-only mode) at least once.
So we can simply the sunxi musb glue by always registering its extcon
notifier and relying on sunxi_musb_work() to enable vbus when in
host-only mode.
This also enables host- and peripheral-only mode with vbus monitoring.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunxi_musb_dma_controller_create and _destroy are not exported
or used outside the driver, so fix sparse warnings by making these
two static:
drivers/usb/musb/sunxi.c:357:23: warning: symbol 'sunxi_musb_dma_controller_create' was not declared. Should it be static?
drivers/usb/musb/sunxi.c:363:6: warning: symbol 'sunxi_musb_dma_controller_destroy' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move struct cppi41_dma_channel to the header file so other modules can
use it.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
davinci.h is not required by cppi_dma.h but cppi_dma.c, so move the
include to the right place.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds tracepoints to dump musb interrupt events.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds tracepoints to musb register read/write wrappers to get
trace log for register access.
The default tacepoint log prefix here would be musb_readX/writeX(),
which is not much helpful. So this patch let the tracepoints use
__buildin_return_address(0) to print the caller funciton name to
provide more context of the register access.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb core already exports the register read/write wrappers, so clean up
the duplication in dsps glue.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid printk() overhead while debugging, this patch implements the
foundation of tracepoints logging for musb driver to make debug
easier.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment is wrong, glue is devm_kzalloc-ed mem attached to the
"allwinner,sun4i-a10-musb" compatible platform-dev. Where as
glue->musb_pdev is a newly created "musb-hdrc" platform-dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop using the return value of platform_device_register_full() to get to
the struct musb in sunxi_musb_work(). If a gadget has been registered
(insmod-ed) before the musb driver, then musb_start will get called
from the musb_core probe function and sunxi_musb_work() may run before
platform_device_register_full() has returned.
Instead store a pointer to struct musb in struct sunxi_glue when
sunxi_musb_enable gets called. Note that sunxi_musb_enable always gets
called before sunxi_musb_work() can run.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the endpoint is stopped by clearing REQPKT before
clearing DATAERR_NAKTIMEOUT before rotating the queue on the
dedicated bulk endpoint.
This addresses an issue where a race could result in the endpoint
receiving data before it was reprogrammed resulting in a warning
about such data from musb_rx_reinit before it was thrown away.
The data thrown away was a valid packet that had been correctly
ACKed which meant the host and device got out of sync.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
shared_fifo endpoints would only get a previous tx state cleared
out, the rx state was only cleared for non shared_fifo endpoints
Change this so that the rx state is cleared for all endpoints.
This addresses an issue that resulted in rx packets being dropped
silently.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Incorrect cppi dma channel is referenced in musb_rx_dma_iso_cppi41(),
which causes kernel NULL pointer reference oops later when calling
cppi41_dma_channel_program().
Fixes: 069a3fd (usb: musb: Remove ifdefs for musb_host_rx in musb_host.c
part1)
Cc: <stable@vger.kernel.org> # v4.2+
Reported-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the session bit was not set in the backup of devctl register,
restoring devctl would clear the session bit. Therefor, only restore
devctl register when the session bit was set in the backup.
This solves the device enumeration failure in otg mode exposed by commit
56f487c (PM / Runtime: Update last_busy in rpm_resume).
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no longer any need for custom initcall level for
musb.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the pull up being handled with delayed work, we can
now finally remove pm_runtime_set_irq_safe that blocks the
MUSB glue from idling.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With PM runtime behaving, these are all now unnecessary.
Doing pm_runtime_get(musb->controller) will keep the parent
glue layer also active.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least on n900 we have phy-twl4030-usb only generating cable
interrupts, and then have a separate USB PHY.
In order for musb to know the real cable status, we need to
clear any cached state until musb is ready. Otherwise the cable
status interrupts will get just ignored if the status does
not change from the initial state.
To do this, let's add a return value to musb_mailbox(), and
reset cached linkstat to MUSB_UNKNOWN on error. Sorry to cause
a bit of churn here, I should have added that already last time
patching musb_mailbox().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least 2430 glue layer pulls d+ high on start up even if there are
no gadgets configured. This is bad at least for anything using a separate
battery charger chip as it can confuse the charger detection.
Let's fix the issue by removing the bogus glue layer code tinkering
with the SESSION bit. As pointed out Bin Liu <b-liu@ti.com> and
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>, the SESSION
bit just starts host mode if ID pin is grounded, and starts the
srp is ID pin is floating. So without the ID pin changing, it's
unable to force musb mode to anything. And just for starting a
host mode, things work fine without this code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is no longer needed with PM runtime at least for 2430 glue.
We can now rely only on PM runtime and cable detection.
The other glue layers can probably remove try_idle too, but that
needs to be tested for each platform before doing it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This simplifies things and allows idling both MUSB and PHY
when nothing is configured. Let's just return early from PM
runtime if musb is not yet initialized.
Let's also warn if PHY is not configured.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may have drivers loaded but no configured gadgets and MUSB may be in
host mode. If gadgets are configured during host mode, PM runtime will
get confused.
Disable PM runtime from gadget state, and do it based on the cable
and last state.
Note that we may get multiple cable events, so we need to keep track
of the power state.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have MUSB setting pm_runtime_irq_safe with the following
commits:
30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel panic")
3e43a07256 ("usb: musb: core: add pm_runtime_irq_safe()")
Let's fix things to use delayed work so we can remove the
pm_runtime_irq_safe.
Note that we may want to set this up in a generic way in the
gadget framework eventually.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conditional use of PM runtime does not work properly
for musb gadget. On cable disconnect we may not get any
USB_EVENT_NONE leaving the PM runtime call unpaired.
Let's fix the issue by making sure the PM runtime calls are
paired within the functions. The glue layer will take care
of the rest.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's not tinker with the PM runtime of musb core from the omap2430
wrapper. This allows us to initialize PM runtime for musb core later
on instead of doing it in stages. And omap2430 wrapper has no need
to for accessing musb core at this point.
Note that this does not remove all the PM runtime calls from the
glue layer, those will get removed in a later patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's make the PM runtime use the standard autosuspend calls.
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") means we must pair use_autosuspend with
dont_use_autosuspend and then use put_sync to properly idle the
device.
Note that we'll be removing the PM runtime calls from the glue
layer to the MUSB core in the next patch. And we can also remove
the pointless FIXME comment now.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have remove() already calling shutdown(), so let's drop it
and move the code to remove(). No code changes, we'll drop the
the FIXME in the following patch with more clean-up.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like at least 2430 glue won't idle reliably with the 200 ms
autosuspend delay. This causes deeper idle states being blocked for
the whole SoC when disconnecting OTG A cable.
Increasing the delay to 500 ms seems to idle both MUSB and the PHY
reliably. This is probably because of time needed by the hardware
based negotiation between MUSB and the PHY.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the board is powering attached usb devices via the otg port
sometimes / on some devices it takes slightly too long for the Vbus
detection code in phy-sun4i-usb.c to signal that Vbus is high after
enabling Vbus and the musb hardware signals a MUSB_INTR_VBUSERROR
interrupt.
This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
VBUSERROR interrupts, fixing connection issues in these cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the mode handling to the platform_set_mode callback.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the DMA engine check was moved to musb_tx_dma_porgram(), both
musb_tx_dma_set_mode_cppi_tusb() and musb_tx_dma_set_mode_mentor() always
return 0, so we can make both these functions *void*.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 754fe4a92c ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
looks incomplete: the DMA engine checks are done outside the Mentor/UX500
handler but inside the CPPI/TUSB handler. Move the checks out of the CPPI/
TUSB handler into its caller, musb_tx_dma_program().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
urb->status is set when endpoint csr RXSTALL, H_ERROR, DATAERROR or
INCOMPRX bit is set. Those bits mean a broken pipe, so don't start next
urb when any of these bits is set by checking urb->status.
To minimize the risk of regression, only do so for RX, until we have a
test case to understand the behavior of TX.
The patch fixes system freeze issue caused by repeatedly invoking RX ISR
while removing a usb uart device connected to a hub, in which case the
hub has no chance to report the disconnect event due to the kernel is
busy in processing the RX interrupt flooding.
Fix checkpatch complaint (qh != NULL) as while.
Reported-by: Max Uvarov <muvarov@gmail.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUSB Programming Guide states that the driver should clear RXCSR
bit2 when the controller sets the bit.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_get_phy() function returns either a valid pointer to phy or
ERR_PTR() error, check for NULL always fails and may lead to oops on
error path, fix this issue.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2035772010.
Commit 20357720 claims throughput improvement for MSC/UVC, but I
don't see much improvement. Following are the MSC measurement using
dd on AM335x GP EVM.
with BCD_BH: read: 14.9MB/s, write: 20.9MB/s
without BCD_BH: read: 15.2MB/s, write: 21.2MB/s
However with this commit the following regressions have been observed.
1. ASIX usb-ethernet dongle is completely broken on UDP RX.
2. Unpluging a 3G modem, which uses option driver, behind a hub causes
console log flooding with the following message.
option_instat_callback: error -71
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions, such as f_sourcesink, rely on an endpoint's desc
field during their requests' complete() callback, so clear it only
_after_ nuking all requests to avoid NULL pointer dereference.
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb_hdrc_platform_data::config was defined as a non-const pointer.
However some drivers (e.g. the ux500) set up this pointer to point to a
static structure, which is potentially dangerous. Since the musb core
uses the pointer in a read-only manner the const qualifier was added to
protect the content of the config.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
MODULE_DEVICE_TABLE() is missing, so the module isn't auto-loading on
sunxi systems using the OTG controller. This commit adds the missing
line so it loads automatically when building it as a module and running
on a system with an USB OTG port.
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When dma_addr_t is 64-bit, we get a warning about an invalid cast
in the call to ux500_dma_is_compatible() from ux500_dma_channel_program():
drivers/usb/musb/ux500_dma.c: In function 'ux500_dma_channel_program':
drivers/usb/musb/ux500_dma.c:210:51: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
if (!ux500_dma_is_compatible(channel, packet_sz, (void *)dma_addr, len))
The problem is that ux500_dma_is_compatible() is called from the
main musb driver on the virtual address, but here we pass in a
DMA address, so the types are fundamentally different but it works
because the function only checks the alignment of the buffer and
that is the same.
We could work around this by adding another cast, but I have checked
that the buffer we get passed here is already checked before it
gets mapped, so the second check seems completely unnecessary
and removing it must be the cleanest solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The musb driver prints DMA addresses in a few places, using the
0x%x format string. This is wrong on 64-bit architectures (which
need %lx) and 32-bit ARM with CONFIG_LPAE set (which needs
%llx), otherwise we print the wrong data, as gcc warns:
musb/musbhsdma.c: In function 'configure_channel':
musb/musbhsdma.c:120:53: error: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
dev_dbg(musb->controller, "%p, pkt_sz %d, addr 0x%x, len %d, mode %d\n",
musb/musbhsdma.c: In function 'dma_channel_program':
musb/musbhsdma.c:155:53: error: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
dev_dbg(musb->controller, "ep%d-%s pkt_sz %d, dma_addr 0x%x length %d, mode %d\n",
musb/tusb6010_omap.c: In function 'tusb_omap_dma_program':
musb/tusb6010_omap.c:313:53: error: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
dev_dbg(musb->controller, "ep%i %s dma ch%i dma: %08x len: %u(%u) packet_sz: %i(%i)\n",
This uses the %pad format string, which prints a dma_addr_t that
gets passed by reference, which works for all combinations.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Commit ac33cdb166 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.
The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.
As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Commit 754fe4a92c ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
introduces a problem setting the desired channel mode for the Mentor DMA
engine.
There is a case where an address is incorrectly assigned to the DMA
channel desired mode when it should instead be assigned the actual mode
value. This results in the value of channel->desired_mode not being
correct.
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
CC drivers/usb/musb/tusb6010.o
drivers/usb/musb/tusb6010.c: In function ‘tusb_musb_init’:
drivers/usb/musb/tusb6010.c:1133:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
sync = ioremap(mem->start, resource_size(mem));
^
drivers/usb/musb/tusb6010.c:1133:7: warning: assignment makes pointer from integer without a cast [enabled by default]
sync = ioremap(mem->start, resource_size(mem));
^
drivers/usb/musb/tusb6010.c:1162:4: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(sync);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede