MCU is an external Freescale MC9S08QG8 microcontroller, mainly used to
provide soft power-off function, but also exports two GPIOs (wired to
the LEDs and also available from the external headers).
Added the MCU on mpc8349emitx, mpc837xrdb and mpc8315erdb boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.
83xx pci nodes have this change:
register properties now contain two address length tuples:
First is the pci bridge register base, this has always been there.
Second is the config base, this is new.
This is documented in dts-bindings/fsl/83xx-512x-pci.txt
The changes accomplish these things:
mpc83xx_add_bridge no longer needs to call get_immrbase
it uses hard coded addresses if the second register value is missing
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added DMA nodes for the elo/elo-plus DMA engines.
Renamed the interrupt controller alias in mpc832x_rdb.dts to ipic so that
its the same as all the other boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MDIO-less PHYs should use CONFIG_FIXED_PHY driver and appropriate
fixed-link property in the device tree.
If not, ethernet will not work:
e0024520:03 not found
eth1: Could not attach to PHY
IP-Config: Failed to open eth1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
This patch fixes USB malfunctioning on the MPC837xE-RDB boards.
Similar patch has been already applied for the MDS boards:
commit 28b9588592
Author: Li Yang <leoli@freescale.com>
Date: Thu Mar 6 18:42:26 2008 +0800
[POWERPC] 83xx: Fix wrong USB phy type in mpc837xmds dts
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch converts the remaining 83xx boards to the dts-v1 format.
This includes the mpc8313_rdb, mpc832x_mds, mpc8323_rdb, mpc8349emitx,
mpc8349emitxgp and the mpc836x_mds.
The mpc8315_rdb mpc834x_mds, mpc837[789]_*, and sbc8349 were already
dts-v1 and only undergo minor changes for the sake of formatting
consistency across the whole group of boards; i.e. the idea being
that you can do a "diff -u board_A.dts board_B.dts" and see something
meaningful.
The general rule I've applied is that entries for values normally
parsed by humans are left in decimal (i.e. IRQ, cache size, clock
rates, basic counts and indexes) and all other data (i.e. reg and
ranges, IRQ flags etc.) remain in hex.
I've used dtc to confirm that the output prior to this changeset
matches the output after this changeset is applied for all boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the dts files for the MPC838xE Reference Development Board (RDB).
The board is a mini-ITX reference board with 256M DDR2, 8M flash,
32M NAND, USB, PCI, gigabit ethernet, SATA, and serial.
the difference among the three files is the 8377 has two, the 8378
none, and the 8379 has four sata controllers.
partially based on the 8379 mds device trees.
Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anton Vorontsov