This allows to:
- Remove forward declarations of static functions,
- Coalesce two sections protected by #ifdef CONFIG_SERIAL_SH_SCI_DMA,
- Avoid shuffling functions around in the near future,
- Avoid adding forward declarations in the near future.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On receive DMA time-out, avoid calling sci_dma_rx_push() if no data was
transferred by the timed out DMA request.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_SERIAL_SH_SCI_DMA is enabled, the driver doesn't enable TIE
on SCIF or HSCIF. However, this driver may call sci_tx_interrupt()
in sci_er_interrupt(). After that, the driver cannot care of the
interrupt, and then "irq 109: nobody cared" happens on r8a7791/koelsch
board. This patch fixes the issue.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert] Keep kicking tx when using PIO
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error handler calls sci_rx_interrupt() to drain the receive FIFO if
an error condition happens.
However, if DMA is enabled on SCIFA or SCIFB, this will call
disable_irq_nosync() twice. Due to this imbalance, the receive interrupt
will never be re-enabled, and reception stops forever.
To fix this, restrict draining the FIFO to PIO mode, and just call
sci_receive_chars() directly.
Inspired by a patch from Yoshihiro Shimoda
<yoshihiro.shimoda.uh@renesas.com>.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that this driver causes a NULL pointer
dereference in the following conditions:
- CONFIG_HIGHMEM and CONFIG_SERIAL_SH_SCI_DMA are enabled
- This driver runs on the sci_dma_rx_push()
This issue was caused by virt_to_page(buf) in the sci_request_dma()
because this driver didn't check if the "buf" was valid or not. So,
this patch uses the "buf" from dma_alloc_coherent() as is, not page.
This patch also fixes a WARNING issue in sci_rx_dma_release():
WARNING: CPU: 0 PID: 1328 at lib/dma-debug.c:1125 check_unmap+0x444/0x848()
rcar-dmac e6700000.dma-controller: DMA-API: device driver frees DMA memory with different CPU address [device address=0x000000006dd89000] [size=64 bytes] [cpu alloc address=0x000000016189c000] [cpu free address=0x0000000080000000]
WARNING: CPU: 1 PID: 1 at drivers/base/dma-mapping.c:334 dma_common_free_remap+0x48/0x6c()
trying to free invalid coherent area: (null)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert] Rebased
[geert] Reworded
[geert] Dropped .rx_chunk, as it's always identical to .rx_buf[0]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to keep all buffer and DMA pointers on the stack.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch from using tty_buffer_request_room() and looping over
tty_insert_flip_char() to tty_insert_flip_string().
Keep track of buffer overruns in the icount structure, like
serial_core.c does.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently sci_dma_rx_push() has to find the active scatterlist itself,
but in some cases the caller already knows.
Hence let the caller pass the scatterlist, and introduce a helper to
find the active DMA request while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During serial port shutdown, the DMA receive worker function may still
be called after the receive DMA cleanup function has been called.
Fix this race condition between work_fn_rx() and sci_rx_dma_release() by
acquiring the port's spinlock in sci_rx_dma_release().
This requires releasing the spinlock in work_fn_rx() before calling (any
function that may call) sci_rx_dma_release().
Terminate all active receive DMA descriptors to release them, and to
make sure no more completions come in.
Do the same in sci_tx_dma_release() for symmetry, although the serial
upper layer will no longer submit more data at this point of time.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a problem when the sci_dma_rx_complete() is processed
before cancel process of work_fn_rx() completes by rx_timer_fn().
This patch locks work_fn_rx().
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resubmission of DMA descriptors is explicitly forbidden by the DMA
engine API.
Hence pass DMA_CTRL_ACK to dmaengine_prep_slave_sg(), and prepare a new
DMA descriptor instead of reusing the old one.
Remove sci_port.desc_rx[], as there's no longer a need to access the
active descriptor.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the error handling in sci_submit_rx() by
- Moving it to the end of the function,
- Just calling dmaengine_terminate_all() instead of calling
async_tx_ack() for all already submitted descriptors.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As dmaengine_prep_slave_sg() is called with the DMA_CTRL_ACK flag set
for DMA transmit requests, there's no need to explicitly acknowledge DMA
transmit requests in the DMA transmit completion callback.
Hence remove the call to async_tx_ack(), and remove the now unused
dma_async_tx_descriptor pointer in the sci_port structure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the SCI driver from the SHDMAE-specific partial DMA transfer
handling to the generic dmaengine residual data framework.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace open-coded
- calls to dma_async_tx_descriptor.tx_submit() by calls to the
dmaengine_submit() helper,
- dma_cookie_t comparisons by calls to dma_submit_error().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mapped transmit buffer is never unmapped. This leaks quite some
mappings, as the mapping is done in uart_ops.startup(), i.e. every time
the device is opened. Unmap the buffer on device close.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the DMA transmit code by using dma_map_single() instead of
constantly modifying the single-entry scatterlist to match what's
currently being transmitted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When comparing differently sized types, it's better to use
min_t()/max_t() than adding casts.
Also use "unsigned int" instead of "int", as that's the right type for
the length of an SG entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To function correctly in the presence of an IOMMU, the DMA buffers must
be managed using the DMA channel's device instead of the platform
device's device.
Make sure to free the DMA memory before releasing the channel, not
after.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let sci_request_dma() handle failures to initialize DMA itself.
This way sci_tx_dma_release() and sci_rx_dma_release() don't have to
consider partial initialization, and thus don't need to reset DMA
addresses to DMA_ERROR_CODE, which is not 100% portable access
architectures.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the life of the driver developer/debugger easier:
- Add __func__ prefix to identical messages,
- Add DMA directions to messages,
- Add TX failure messages,
- Always use "cookie %d" for DMA cookies,
- "#%d" is reserved for the DMA cookie/descriptor index.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix an issue that the driver may cause "nobody cared" IRQ
when this driver detects the overrun flag only.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b6ff84c2d ("serial: sh-sci: Fix R-Car SCIF and HSCIF
overrun handling") added overrun handling for (H)SCIF using the SCLSR
register, but also accidentally added a bogus call to
sci_handle_fifo_overrun() in the receive interrupt path.
Remove it again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reorder sampling_rate assignment for consistency in all cases of the
switch statement.
Avoid using the ternary conditional operator to make it more clear that
the value is overridden by platform data.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial_core.c was moved from drivers/serial/ to drivers/tty/serial/ a
while ago. Remove the path to make it move-proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF_ERROR_CLEAR includes SCIFA_ORER, which exists only on SCIFA/SCIFB
and SCIF on sh7705/sh7720/sh7721.
To fix this:
1. Remove SCIFA_ORER from the definition of SCIF_ERROR_CLEAR,
2. During initialization, store the error clear mask to use,
incorporating the overrun bit only if it applies to the SCxSR
register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expressions involving "BIT(...)" create values of type "long", which is
64-bit on 64-bit. Hence "~BIT(...)" no longer fits in 32-bit, which
will cause future compiler warnings when assigning to 32-bit variables:
drivers/tty/serial/sh-sci.c: In function 'sci_init_single':
drivers/tty/serial/sh-sci.h:58:25: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define SCI_ERROR_CLEAR ~(SCI_RESERVED | SCI_PER | SCI_FER | SCI_ORER)
^
drivers/tty/serial/sh-sci.c:2325:27: note: in expansion of macro 'SCI_ERROR_CLEAR'
sci_port->error_clear = SCI_ERROR_CLEAR;
As these values are (at most) 32-bit register values anyway, cast them
to "u32" at the definition level to prevent such compiler warnings.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef logic to clear SCxSR bits using RMW on SCIFA/SCIFB and SCIF
variants with some SCIFA features (sh7705/SH7720/sh7721) has several
drawbacks:
- It wasn't updated for newer R-Mobile variants (APE6),
- It doesn't correctly handle SoCs with both SCIF and SCIFA/B (e.g.
R-Car Gen2, but also legacy sh7723/sh7724),
- It doesn't play well with ARM multi-platform kernels: on R-Car Gen2,
SCIF/SCIFA/SCIFB/HSCIF were handled differently, depending on
whether r8a7740 or sh73a0 support was enabled or not,
Replace the #ifdef logic by runtime logic to fix this.
SCIFA/SCIFB and SCIF on sh7705/sh7720/sh7721 use RMW to clear error
bits, other variants use plain stores, as before.
Note that this changes behavior for SCIFA on sh7723/sh7724 (these SoCs
have both SCIF and SCIFA), which didn't use RMW before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following race conditions can happen when a serial port is used
as console.
Case1: CPU_B is used to detect an interrupt from a serial port,
but it can have interrupts disabled during the waiting time.
Case2: CPU_B clears UART_IER just after CPU_A sets UART_IER and then
a serial port may not make an interrupt.
Case3: CPU_A sets UART_IER just after CPU_B clears UART_IER.
This is an unexpected behavior for serial8250_console_write().
CPU_A [autoconfig_irq] | CPU_B [serial8250_console_write]
----------------------------|---------------------------------------
|
probe_irq_on() | spin_lock_irqsave(&port->lock,)
serial_outp(,UART_IER,0x0f) | serial_out(,UART_IER,0)
udelay(20); | uart_console_write()
probe_irq_off() |
| spin_unlock_irqrestore(&port->lock,)
Case1 and 2 can make autoconfig_irq() failed.
In these cases, the console doesn't work in interrupt mode and
"input overrun" (which can make operation mistakes) can happen
on some systems. Especially in the Case1, It is known that the
problem happens with high rate every boot once it occurs
because the boot sequence is always almost same.
port mutex makes sure that the autoconfig operation is exclusive of
any other concurrent HW access except by the console operation.
console lock is required in autoconfig_irq().
Signed-off-by: Taichi Kageyama <t-kageyama@cp.jp.nec.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes receiving broken characters on the console from an MPC5125
system when systemd comes up which repeatedly opens and shuts down the
console device.
Trial and error with the needed interval showed that 500 us are good
enough most of the time when using 38400 Bd, so I think 1 ms is a good
compromise between fixing the issue and not penalize faster setups too
much.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
8250/Kconfig:config SERIAL_8250_LPC18XX
8250/Kconfig: bool "NXP LPC18xx/43xx serial port support"
...meaning that it currently is not being built as a module by anyone.
When targetting orphaned modular code in non-modular drivers, this
came up. Joachim indicated that the driver was actually meant to
be tristate but ended up bool by accident. So here we make it
tristate instead of removing the modular code that was essentially
orphaned.
Suggested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig for this driver is currently:
config SERIAL_MPSC
bool "Marvell MPSC serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We leave some tags like MODULE_AUTHOR for documentation purposes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/hvc/Kconfig:config HVC_DRIVER
drivers/tty/hvc/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only, even
though someone bothered to comment that the code was not used.
Unlike other changes, this driver binds in w/o using module_init,
so we dont have init ordering concerns with this commit.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
config.debug:config MAGIC_SYSRQ
bool "Magic SysRq key"
...meaning that it currently is not being built as a module by anyone.
Lets remove the traces of modularity we can so that when reading the
driver there is less doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't delete the module.h include since other parts of the file are
using content from there.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/Kconfig:config LEGACY_PTYS
drivers/tty/Kconfig: bool "Legacy (BSD) PTY support"
...and:
drivers/tty/Kconfig:config UNIX98_PTYS
drivers/tty/Kconfig: bool "Unix98 PTY support" if EXPERT
combined with this:
obj-$(CONFIG_LEGACY_PTYS) += pty.o
obj-$(CONFIG_UNIX98_PTYS) += pty.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the traces of modularity we can so that when reading the
driver there is less doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't delete the module.h include since other parts of the file are
using content from there.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CIR type serial ports aren't real serial ports.
This is just a way to prevent legacy 8250 serial
driver from probing and eventually binding some
resources.
Since in current state such ports aren't providing
any real functionality and it is not possible
to change their type via setserial/ioctl(TIOCSSERIAL)
(due to UPF_FIXED_PORT flag set on them)
it is simpler and cleaner to not register them at all
with serial core.
Print a short message in this case so it is known
to user what has happened.
This way checks for PORT_8250_CIR in serial port
callbacks can be removed too, since they won't
ever be called.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tty_insert_flip_string() returns an int and as such it
might fail. So the result is that I kindly asked to insert 48 bytes and
the function only insterted 32.
I have no idea what to do with the remaining 16 so I think dropping them
is the only option. I also increase the buf_overrun counter so userpace
has a clue that we lost bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull x86 fixes from Thomas Gleixner:
"Two bugfixes from Andy addressing at least some of the subtle NMI
related wreckage which has been reported by Sasha Levin"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi/64: Fix a paravirt stack-clobbering bug in the NMI code
x86/paravirt: Replace the paravirt nop with a bona fide empty function
Pull irq fix from Thomass Gleixner:
"A bugfix for the atmel aic5 irq chip driver which caches the wrong
data and thereby breaking resume"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/atmel-aic5: Use per chip mask caches in mask/unmask()
Pull ARM fixes from Russell King:
"Just two fixes: wire up the new system calls added during the last
merge window, and fix another user access site"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: alignment: fix alignment handling for uaccess changes
ARM: wire up new syscalls
Our first real batch of fixes this release cycle. There's a collection of
them here:
- A fixup for a build breakage that hits on arm64 allmodconfig in QCOM SCM
firmware drivers
- MMC fixes for OMAP that had quite a bit of breakage this merge window.
- Misc build/warning fixes on PXA and OMAP
- A couple of minor fixes for Beagleboard X15 which is now starting to see
a few more users in the wild
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ThcO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first real batch of fixes this release cycle. Nothing really
concerning, and diffstat is a bit inflated due to some DT contents
moving around on STi platforms.
There's a collection of them here:
- A fixup for a build breakage that hits on arm64 allmodconfig in
QCOM SCM firmware drivers
- MMC fixes for OMAP that had quite a bit of breakage this merge
window.
- Misc build/warning fixes on PXA and OMAP
- A couple of minor fixes for Beagleboard X15 which is now starting
to see a few more users in the wild"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: sti: dt: adapt DT to fix probe/bind issues in DRM driver
ARM: dts: fix omap2+ address translation for pbias
firmware: qcom: scm: Add function stubs for ARM64
ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
ARM: omap2plus_defconfig: enable GPIO_PCA953X
ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
ARM: dts: am57xx-beagle-x15: Update Phy supplies
ARM: pxa: balloon3: Fix build error
ARM: dts: Fixup model name for HP t410 dts
ARM: dts: DRA7: fix a typo in ethernet
ARM: omap2plus_defconfig: make PCF857x built-in
ARM: dts: Use ti,pbias compatible string for pbias
ARM: OMAP5: Cleanup options for SoC only build
ARM: DRA7: Select missing options for SoC only build
ARM: OMAP2+: board-generic: Remove stale of_irq macros
ARM: OMAP4+: PM: erratum is used by OMAP5 and DRA7 as well
ARM: dts: omap3-igep: Move eth IRQ pinmux to IGEPv2 common dtsi
ARM: dts: am57xx-beagle-x15: Add wakeup irq for mcp79410
ARM: dts: am335x-phycore-som: Fix mpu voltage
...
Pull CIFS fixes from Steve French:
"Four fixes from testing at the recent SMB3 Plugfest including two
important authentication ones (one fixes authentication problems to
some popular servers when clock times differ more than two hours
between systems, the other fixes Kerberos authentication for SMB3)"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
fix encryption error checks on mount
[SMB3] Fix sec=krb5 on smb3 mounts
cifs: use server timestamp for ntlmv2 authentication
disabling oplocks/leases via module parm enable_oplocks broken for SMB3
Geert Uytterhoeven