The seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Guenter Roeck <linux~roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull sparc fixes from David Miller:
1) ldc_alloc_exp_dring() can be called from softints, so use
GFP_ATOMIC. From Sowmini Varadhan.
2) Some minor warning/build fixups for the new iommu-common code on
certain archs and with certain debug options enabled. Also from
Sowmini Varadhan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Use GFP_ATOMIC in ldc_alloc_exp_dring() as it can be called in softirq context
sparc64: Use M7 PMC write on all chips T4 and onward.
iommu-common: rename iommu_pool_hash to iommu_hash_common
iommu-common: fix x86_64 compiler warnings
Pull networking fixes from David Miller:
"Just a few fixes trickling in at this point.
1) If we see an attached socket on an skb in the ipv4 forwarding path,
bail. This can happen due to races with FIB rule addition, and
deletion, and we should just drop such frames. From Sebastian
Pöhn.
2) pppoe receive should only accept packets destined for this hosts's
MAC address. From Joakim Tjernlund.
3) Handle checksum unwrapping properly in ppp receive properly when
it's encapsulated in UDP in some way, fix from Tom Herbert.
4) Fix some bugs in mv88e6xxx DSA driver resulting from the conversion
from register offset constants to mnenomic macros. From Vivien
Didelot.
5) Fix handling of HCA max message size in mlx4 adapters, from Eran
Ben ELisha"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net/mlx4_core: Fix reading HCA max message size in mlx4_QUERY_DEV_CAP
tcp: add memory barriers to write space paths
altera tse: Error-Bit on tx-avalon-stream always set.
net: dsa: mv88e6xxx: use PORT_DEFAULT_VLAN
net: dsa: mv88e6xxx: fix setup of port control 1
ppp: call skb_checksum_complete_unset in ppp_receive_frame
net: add skb_checksum_complete_unset
pppoe: Lacks DST MAC address check
ip_forward: Drop frames with attached skb->sk
Pull parisc fixes from Helge Deller:
"The patch by Guenter Roeck fixes the build on parisc which got broken
because of commit f24ffde432 ("parisc: expose number of page table
levels on Kconfig level") and the patch from Matthew Wilcox converts
our code to use the generic scatterlist.h header file"
* 'parisc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Replace PT_NLEVELS with CONFIG_PGTABLE_LEVELS
parisc: Eliminate sg_virt_addr() and private scatterlist.h
Currently we parse max_msg_sz from the wrong offset in QUERY_DEV_CAP,
fix to use the right offset.
Fixes: 0b131561a7 ('net/mlx4_en: Add Flow control statistics [..]')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is possible for vnet_event_napi to end up doing
vnet_control_pkt_engine -> ... -> vnet_send_attr ->
vnet_port_alloc_tx_ring -> ldc_alloc_exp_dring -> kzalloc()
(i.e., in softirq context), kzalloc() should be called with
GFP_ATOMIC from ldc_alloc_exp_dring.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They both work equally well, and the M7 implementation is
simpler and cheaper (less register writes).
With help from David Ahern.
Signed-off-by: David S. Miller <davem@davemloft.net>
The following warning is seen when compiling parisc images
./arch/parisc/include/asm/pgalloc.h: In function 'pgd_alloc':
./arch/parisc/include/asm/pgalloc.h:29:5: warning: "PT_NLEVELS" is not defined
Some definitions of PT_NLEVELS were missed with the conversion to
CONFIG_PGTABLE_LEVELS.
Fixes: f24ffde432 ("parisc: expose number of page table levels
on Kconfig level")
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The only reason to keep parisc's private asm/scatterlist.h was that it
had the macro sg_virt_addr(). Convert all callers to use something else
(sometimes just sg->offset was enough, others should use sg_virt()), and
we can just use the asm-generic scatterlist.h instead.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Dave Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Ensure that we either see that the buffer has write space
in tcp_poll() or that we perform a wakeup from the input
side. Did not run into any actual problem here, but thought
that we should make things explicit.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more input subsystem updates from Dmitry Torokhov:
- an update to Atmel MXT driver that makes it functional on Google
Pixel 2 boxes (both touchpad and touchscreen)
- a new VMware VMMouse driver that should allow us drop X vmmouse
driver that requires root privileges (since it accesses ioports)
- XBox One controllers now support force feedback (rumble)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: lm8333 - fix broken email address
Input: cyapa - fix setting suspend scan rate
Input: elan_i2c - fix calculating number of x and y traces.
Input: elan_i2c - report hovering contacts
Input: elants_i2c - zero-extend hardware ID in firmware name
Input: alps - document separate pointstick button bits for V2 devices
Input: atmel_mxt_ts - add support for Google Pixel 2
Input: xpad - add rumble support for Xbox One controller
Input: ff-core - use new debug macros
Input: add vmmouse driver
Input: elan_i2c - adjust for newer firmware pressure reporting
My 'allmodconfig' build is _almost_ free of warnings, and most of the
remaining ones are for legacy drivers that just do bad things that I
can't find it in my black heart to care too much about. But this one
was just annoying me:
drivers/media/v4l2-core/videobuf2-core.c:3256:26: warning: unused variable ‘fileio’ [-Wunused-variable]
because commit 0e66100637 ("[media] vb2: fix 'UNBALANCED' warnings
when calling vb2_thread_stop()") removed all users of 'fileio' and
instead calls "__vb2_cleanup_fileio(q)" to clean up q->fileio. But the
now unused 'fileio' variable was left around.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HpGw
-----END PGP SIGNATURE-----
Merge tag 'media/v4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a new frontend driver for new ATSC devices: lgdt3306a
- a new sensor driver: ov2659
- a new platform driver: xilinx
- the m88ts2022 tuner driver was merged at ts2020 driver
- the media controller gained experimental support for DVB and hybrid
devices
- lots of random cleanups, fixes and improvements on media drivers
* tag 'media/v4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (404 commits)
[media] uvcvideo: add support for VIDIOC_QUERY_EXT_CTRL
[media] uvcvideo: fix cropcap v4l2-compliance failure
[media] media: omap3isp: remove unused clkdev
[media] coda: Add tracing support
[media] coda: drop dma_sync_single_for_device in coda_bitstream_queue
[media] coda: fix fill bitstream errors in nonstreaming case
[media] coda: call SEQ_END when the first queue is stopped
[media] coda: fail to start streaming if userspace set invalid formats
[media] coda: remove duplicate error messages for buffer allocations
[media] coda: move parameter buffer in together with context buffer allocation
[media] coda: allocate bitstream buffer from REQBUFS, size depends on the format
[media] coda: allocate per-context buffers from REQBUFS
[media] coda: use strlcpy instead of snprintf
[media] coda: bitstream payload is unsigned
[media] coda: fix double call to debugfs_remove
[media] coda: check kasprintf return value in coda_open
[media] coda: bitrate can only be set in kbps steps
[media] v4l2-mem2mem: no need to initialize b in v4l2_m2m_next_buf and v4l2_m2m_buf_remove
[media] s5p-mfc: set allow_zero_bytesused flag for vb2_queue_init
[media] coda: set allow_zero_bytesused flag for vb2_queue_init
...
Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog below.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IMEACgkQMUfUDdst+yloDQCfbyIRL23WVAn9ckQse/y8gbjB
OT4AoKTJbwndDP9Kb/lrj2tjd9QjNVrC
=xhen
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog.
All of this has been in linux-next for a while"
* tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (133 commits)
mei: trace: remove unused TRACE_SYSTEM_STRING
DTS: ARM: OMAP3-N900: Add lis3lv02d support
Documentation: DT: lis302: update wakeup binding
lis3lv02d: DT: add wakeup unit 2 and wakeup threshold
lis3lv02d: DT: use s32 to support negative values
Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX case
Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages case
mei: replace check for connection instead of transitioning
mei: use mei_cl_is_connected consistently
mei: fix mei_poll operation
hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg()
Drivers: hv: hv_balloon: survive ballooning request with num_pages=0
Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor function
Drivers: hv: hv_balloon: do not online pages in offline blocks
hv: remove the per-channel workqueue
hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind()
hv: run non-blocking message handlers in the dispatch tasklet
coresight: moving to new "hwtracing" directory
coresight-tmc: Adding a status interface to sysfs
coresight: remove the unnecessary configuration coresight-default-sink
...
Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some odd
reason, but Peter is working on fixing that. If not, I'll send a revert
for the offending patch, but I have faith that Peter can address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices in
the future.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IcUACgkQMUfUDdst+ylFqACcC8LPhFEZg9aHn0hNUoqGK3rE
5dUAnR4b8r/NYqjVoE9FJZgZfB/TqVi1
=lyN/
-----END PGP SIGNATURE-----
Merge tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some
odd reason, but Peter is working on fixing that. If not, I'll send a
revert for the offending patch, but I have faith that Peter can
address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices
in the future.
All of these have been in linux-next for a while"
* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
n_gsm: Drop unneeded cast on netdev_priv
sc16is7xx: expose RTS inversion in RS-485 mode
serial: 8250_pci: port failed after wakeup from S3
earlycon: 8250: Document kernel command line options
earlycon: 8250: Fix command line regression
earlycon: Fix __earlycon_table stride
tty: clean up the tty time logic a bit
serial: 8250_dw: only get the clock rate in one place
serial: 8250_dw: remove useless ACPI ID check
dmaengine: hsu: move memory allocation to GFP_NOWAIT
dmaengine: hsu: remove redundant pieces of code
serial: 8250_pci: add Intel Tangier support
dmaengine: hsu: add Intel Tangier PCI ID
serial: 8250_pci: replace switch-case by formula for Intel MID
serial: 8250_pci: replace switch-case by formula
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
serial: jsm: some off by one bugs
serial: xuartps: Fix check in console_setup().
serial: xuartps: Get rid of register access macros.
serial: xuartps: Fix iobase use.
...
drivers and updates to existing ones for feature enhancements and bug
fixes. There is more churn than usual in the framework core due to the
change to introduce per-user unique struct clk pointers in 4.0. This
caused several regressions to surface, some of which were sent as fixes
to 4.0. New generic clock drivers were added for GPIO- and PWM-based
clock controllers. Additionally the common clk-divider code recieved
several fixes to the way it rounds rates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2LMr
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.0 are mostly new clock
drivers and updates to existing ones for feature enhancements and bug
fixes.
There is more churn than usual in the framework core due to the change
to introduce per-user unique struct clk pointers in 4.0. This caused
several regressions to surface, some of which were sent as fixes to
4.0. New generic clock drivers were added for GPIO- and PWM-based
clock controllers.
Additionally the common clk-divider code recieved several fixes to the
way it rounds rates"
* tag 'clk-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (91 commits)
clk: check ->determine/round_rate() return value in clk_calc_new_rates
clk: at91: usb: propagate rate modification to the parent clk
clk: samsung: exynos4: Disable ARMCLK down feature on Exynos4210 SoC
clk: don't use __initconst for non-const arrays
clk: at91: change to using endian agnositc IO
clk: clk-gpio-gate: Fix active low
clk: Add PWM clock driver
clk: Add clock driver for mb86s7x
clk: pxa: pxa3xx: add missing os timer clock
clk: tegra: Use the proper parent for plld_dsi
clk: tegra: Use generic tegra_osc_clk_init() on Tegra114
clk: tegra: Model oscillator as clock
clk: tegra: Add peripheral registers for bank Y
clk: tegra: Register the proper number of resets
clk: tegra: Remove needless initializations
clk: tegra: Use consistent indentation
clk: tegra: Various whitespace cleanups
clk: tegra: Enable HDA to HDMI clocks on Tegra124
clk: tegra: Fix a bunch of sparse warnings
clk: tegra: Fix typo tabel -> table
...
This reverts commit e2ac55b6a8.
Huang Ying reports that this causes a hang at boot with debugfs disabled.
It is true that the debugfs error checks are kind of confusing, and this
code certainly merits more cleanup and thinking about it, but there's
something wrong with the trivial "check not just for NULL, but for error
pointers too" patch.
Yes, with debugfs disabled, we will end up setting the o2hb_debug_dir
pointer variable to an error pointer (-ENODEV), and then continue as if
everything was fine. But since debugfs is disabled, all the _users_ of
that pointer end up being compiled away, so even though the pointer can
not be dereferenced, that's still fine.
So it's confusing and somewhat questionable, but the "more correct"
error checks end up causing more trouble than they fix.
Reported-by: Huang Ying <ying.huang@intel.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Chengyu Song <csong84@gatech.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
* patchwork: (404 commits)
[media] uvcvideo: add support for VIDIOC_QUERY_EXT_CTRL
[media] uvcvideo: fix cropcap v4l2-compliance failure
[media] media: omap3isp: remove unused clkdev
[media] coda: Add tracing support
[media] coda: drop dma_sync_single_for_device in coda_bitstream_queue
[media] coda: fix fill bitstream errors in nonstreaming case
[media] coda: call SEQ_END when the first queue is stopped
[media] coda: fail to start streaming if userspace set invalid formats
[media] coda: remove duplicate error messages for buffer allocations
[media] coda: move parameter buffer in together with context buffer allocation
[media] coda: allocate bitstream buffer from REQBUFS, size depends on the format
[media] coda: allocate per-context buffers from REQBUFS
[media] coda: use strlcpy instead of snprintf
[media] coda: bitstream payload is unsigned
[media] coda: fix double call to debugfs_remove
[media] coda: check kasprintf return value in coda_open
[media] coda: bitrate can only be set in kbps steps
[media] v4l2-mem2mem: no need to initialize b in v4l2_m2m_next_buf and v4l2_m2m_buf_remove
[media] s5p-mfc: set allow_zero_bytesused flag for vb2_queue_init
[media] coda: set allow_zero_bytesused flag for vb2_queue_init
...
The Error-Bit on the avalon streaming interface of the
tx-dma-channel was always set. In SGMII configurations
this leads to error-symbols on the PCS and packet-rejection
on the receiver side (e.g. SGMII/1000Base-X connected switch).
This only applies to the tse-configuration with MSGDMA.
This issue was detected and fixed on a custom board with
a direct connection to a Marvell switch in SGMII-PHY-Mode.
(incl. custom patches for SGMII-PCS).
According to the datasheet if ff_tx_err (avalon-streaming)
is set it is forwarded to gm_tx_err. As a result the PCS
is forwarding the error by sending a "/V/"-caracter.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor, use the explicit PORT_DEFAULT_VLAN define instead of 0x07.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_setup_port_common was writing to PORT_DEFAULT_VLAN (port
offset 0x07) instead of PORT_CONTROL_1 (port offset 0x05).
Fixes: cca8b13375 ("net: dsa: Use mnemonics rather than register numbers")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert says:
====================
net: Fix "hw csum failure" message flood for ppp tunnel
This patch set addresses bug "Bug 95171 - "hw csum failure" message
flood for ppp tunnel since upgrade to 3.16". The problem is that pppoe
is being used over UDP with UDP checksusm enabled. On receive
checksum conversion turns checksum-unnecessary in checksum-
complete. The PPP receive functions do not properly pull
the checksum over its headers, so that when an encapsulated
checksums is considered the checksum-complete value is incorrect.
This patch adds skb_checksum_complete_unset which can be called
in the receive path in lieu of pulling checksum complete in
layer. This is useful when the packet is being modified (e.g.
decompressed) and the checksum-complete value is no longer
relevant.
In the ppp_receive_frame we call skb_checksum_complete_unset to toss
out checksum-complete. This should eliminate the reported messages.
Alternatively, we could add skb_postpull_rcsum and probably
special case handling for VJ compression if maintaining the
checksum-complete is needed (not clear to me this is worth the
effort).
I haven't tested this since setting up the failure scenario doesn't
seem trivial to configure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Call checksum_complete_unset in PPP receive to discard checksum-complete
value. PPP does not pull checksum for headers and also modifies packet
as in VJ compression.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function changes ip_summed to CHECKSUM_NONE if CHECKSUM_COMPLETE
is set. This is called to discard checksum-complete when packet
is being modified and checksum is not pulled for headers in a layer.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=a3aV
-----END PGP SIGNATURE-----
Merge tag 'remoteproc-4.1-next' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc
Pull remoteproc update from Ohad Ben-Cohen:
"Suman Anna is adding remoteproc support for processors not behind
IOMMUs"
* tag 'remoteproc-4.1-next' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc: add IOMMU hardware capability flag
Pull misc kbuild updates:
"This is the remaining part of kbuild stuff for v4.1-rc1:
- One wew coccinelle script and a clarification of the proposed fix
in bugon.coccinelle
- CONFIG_KERNEL_LZ4 support for extract-ikconfig"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/coccinelle/misc/bugon.cocci: update bug_on conversion warning
scripts/extract-ikconfig: Support LZ4-compressed images.
irqf_oneshot.cocci: add check of devm_request_threaded_irq()
I'd like to say these were a set of regressions for the recent merge window
code. Unfortunately, they all predate the merge window code (stable cc'd).
There's two fixes for data integrity (mostly only showing up on module
removal), an mvsas crash with expander attached SATA devices which goes back
to the dawn of the driver but is only just being picked up as sas expanders
become a standard item in low end server hardware, an am53c974 one because the
interrupt data isn't fully initialised before the line is and a megaraid_sas
one because it uses smp_processor_id() to select MSI-X queues and that now
triggers a WARN_ON().
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVM+JoAAoJEDeqqVYsXL0My40H/Rtb85O+nLmsaPutyM3LqfNb
EKeF7voVsEp2uaNodx5xYe3Q3FpGW/dfct0uSrAD1fYWkr/z+9VJlYkh1dY0Z7Tq
FjbWufPWmRbqvk6q4C4bBkFRBKbX38cmdY9kJQgby6dqPXKhe0LKPJy+ik30b0HV
PWK6Voh3Y41zeOk/q4I2RvEREW+cCz1PTiQRP45Y1j+ilslmDGDH95KZ3PZPwE6t
xOfj9DpGBKmN5Fvn7mIPZA72Xpnmc3Zlw7gv8ZBctxpHRvO+woQXjRqORUEBu4bA
Cwg9lJnyRjDiTarm9ceCm8c5bmlii6Furfn/qxxnW9d64h4K1ed6lf0D/BehAdY=
=U1F+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"I'd like to say these were a set of regressions for the recent merge
window code. Unfortunately, they all predate the merge window code
(stable cc'd).
There are two fixes for data integrity (mostly only showing up on
module removal), an mvsas crash with expander attached SATA devices
which goes back to the dawn of the driver but is only just being
picked up as sas expanders become a standard item in low end server
hardware, an am53c974 one because the interrupt data isn't fully
initialised before the line is and a megaraid_sas one because it uses
smp_processor_id() to select MSI-X queues and that now triggers a
WARN_ON()"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
mvsas: fix panic on expander attached SATA devices
am53c974: Fix crash during modprobe
megaraid_sas: use raw_smp_processor_id()
sd: Fix missing ATO tag check
sd: Unregister integrity profile
Pull drm updates from Dave Airlie:
"Highlights:
Core:
- Virtual GEM layer merged, this has been around for a long time, and
it provides a software backed device that allows userspace to use
it as a GEM shared memory handler. This makes it a lot easier to
do certain things when you have no GPU but still have to deal with
DRI expectations.
- atomic helper updates.
- framebuffer modifier interface added.
- i2c over auxch displayport fixes.
- fb width/height confusion fixes.
- new driver for ps8622/ps8625 bridge chips
- lots of new panels
i915:
- more plane atomic conversion
- vGPU guest support for XenGT
- Skylake workarounds and fixes
- Y-tiling support
- work on dynamic pagetable allocation
- EU count report param for gen9+
- CHV fixes (no longer prelim)
- remove ilk rc6
- frontbuffer tracking for fbc
- Displayport link rate refactoring
- sprite colorkey refactor
radeon:
- Displayport MST support (not enabled by default)
- non-ATOM native hw auxch support (DCE5+)
- output csc support
- new queries for userspace debug support
- new VCE packet
nouveau:
- gk20a iommu support
- gm107 graphics support
- more gm20x bringup (waiting on signed nvidia fw).
amdkfd:
- multiple kgd instance support
- use 64-bit time accessors
msm:
- stolen memory support
- DSI and dual-DSI support
- snapdragon 410 support
exynos:
- cleanups for atomic and pageflip
imx-drm:
- more media-bus formats
- TV output prep
- drm panel support
tegra:
- hw vblank counter using host1x syncpoints
omap:
- universal plane support
- prep work for atomic modesetting
rcar-du:
- ported to atomic modesetting
atmel-hlcdc:
- ported to atomic modesetting
- added suspend/resume support
sti:
- ported to atomic modesetting
dwhdmi:
- more compliant audio support
- update rockchip phy support
tda998x:
- DT probing for attached crtcs
- simplified EDID reading
rockchip:
- fixes
adv7511:
- fixes"
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (689 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
drm/i915: Dont enable CS_PARSER_ERROR interrupts at all
drm/i915: Move drm_framebuffer_unreference out of struct_mutex for takeover
drm: fix trivial typo mistake
drm: Make integer overflow checking cover universal cursor updates (v2)
drm/nouveau/bios: fix fetching from acpi on certain systems
drm/nouveau/gr/gm206: initial init+ctx code
drm/nouveau/ce/gm206: enable support via gm204 code
drm/nouveau/fifo/gm206: enable support via gm204 code
drm/nouveau/gr/gm204: initial init+ctx code
drm/nouveau: support for buffer moves via MaxwellDmaCopyA
drm/nouveau/ce/gm204: initial support
drm/nouveau: add support for gm20x fifo channels
drm/nouveau/fifo/gm204: initial support
drm/nouveau/gr/gk104-: prevent reading non-existent regs in intr handler
drm/nouveau/gr/gm107: very slightly demagic part of attrib cb setup
drm/nouveau/gr/gk104-: correct crop/zrop num_active_fbps setting
drm/nouveau/gr/gf100-: add symbolic names for classes
drm/nouveau/gr/gm107: support tpc "strand" ctxsw in gpccs ucode
drm/nouveau/gr/gf100-: support mmio access with gpc offset from gpccs ucode
...
A pppoe session is identified by its session ID and MAC address.
Currently pppoe does not check if the received pkg has the correct
MAC address. This is a problem when the eth I/F is in promisc mode
as then any DST MAC address is accepted.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan says:
====================
iommu-common build warning fixes.
This patchset has fixes for 2 architectures
- Part 1: x86_64 warnings generated by sparse
- Part 2: allmodconfig build error for powerpc, identified by Guenter Roeck.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_DEBUG_FORCE_WEAK_PER_CPU is set, the DEFINE_PER_CPU_SECTION
macro will define an extern __pcpu_unique_##name variable that could
conflict with the same definition in powerpc at this time. Avoid that
conflict by renaming iommu_pool_hash in iommu-common.c
Thanks to Guenter Roeck for catching this, and helping to test the fix.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial discussion was:
[FYI] xfrm: Don't lookup sk_policy for timewait sockets
Forwarded frames should not have a socket attached. Especially
tw sockets will lead to panics later-on in the stack.
This was observed with TPROXY assigning a tw socket and broken
policy routing (misconfigured). As a result frame enters
forwarding path instead of input. We cannot solve this in
TPROXY as it cannot know that policy routing is broken.
v2:
Remove useless comment
Signed-off-by: Sebastian Poehn <sebastian.poehn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not much this time, but the changes include:
* Moving domain allocation into the iommu drivers to prepare for
the introduction of default domains for devices
* Fixing the IO page-table code in the AMD IOMMU driver to
correctly encode large page sizes
* Extension of the PCI support in the ARM-SMMU driver
* Various fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVNFIPAAoJECvwRC2XARrj4v8QAMVsPJ+kmnLvqGDkO9v2i9z6
sFX27h55HhK3Pgb5aEmEhvZd0Eec22KtuADr92LsRSjskgA4FgrzzSlo8w7+MbwM
dtowij+5Bzx/jEeexM5gog0ZA9Brl725KSYBmwJIAroKAtl3YXsIA4TO7X/JtXJm
0qWbCxLs9CX5uWyJawkeDl8UAaZYb8AHKv1UhJt8Z5yajM/qITMULi51g2Bgh8kx
YaRHeZNj+mFQqb6IlNkmOhILN+dbTdxQREp+aJs1alGdkBGlJyfo6eK4weNOpA4x
gc8EXUWZzj1GEPyWMpA/ZMzPzCbj9M6wTeXqRiTq31AMV10zcy545uYcLWks680M
CYvWTmjeCvwsbuaj9cn+efa47foH2UoeXxBmXWOJDv4WxcjE1ejmlmSd8WYfwkh9
hIkMzD8tW2iZf3ssnjCeQLa7f6ydL2P4cpnK2JH+N7hN9VOASAlciezroFxtCjU+
18T7ozgUTbOXZZomBX7OcGQ8ElXMiHB/uaCyNO64yVzApsUnQfpHzcRI5OavOYn5
dznjrzvNLCwHs3QFI4R7rsmIfPkOM0g5nY5drGwJ23+F+rVpLmpWVPR5hqT7a1HM
tJVmzces6HzOu7P1Mo0IwvNbZEmNBGTHYjGtWs6e79MQxdriFT4I+DwvFOy7GUq/
Is2b+HPwWhiWJHQXLTT2
=FMxH
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"Not much this time, but the changes include:
- moving domain allocation into the iommu drivers to prepare for the
introduction of default domains for devices
- fixing the IO page-table code in the AMD IOMMU driver to correctly
encode large page sizes
- extension of the PCI support in the ARM-SMMU driver
- various fixes and cleanups"
* tag 'iommu-updates-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (34 commits)
iommu/amd: Correctly encode huge pages in iommu page tables
iommu/amd: Optimize amd_iommu_iova_to_phys for new fetch_pte interface
iommu/amd: Optimize alloc_new_range for new fetch_pte interface
iommu/amd: Optimize iommu_unmap_page for new fetch_pte interface
iommu/amd: Return the pte page-size in fetch_pte
iommu/amd: Add support for contiguous dma allocator
iommu/amd: Don't allocate with __GFP_ZERO in alloc_coherent
iommu/amd: Ignore BUS_NOTIFY_UNBOUND_DRIVER event
iommu/amd: Use BUS_NOTIFY_REMOVED_DEVICE
iommu/tegra: smmu: Compute PFN mask at runtime
iommu/tegra: gart: Set aperture at domain initialization time
iommu/tegra: Setup aperture
iommu: Remove domain_init and domain_free iommu_ops
iommu/fsl: Make use of domain_alloc and domain_free
iommu/rockchip: Make use of domain_alloc and domain_free
iommu/ipmmu-vmsa: Make use of domain_alloc and domain_free
iommu/shmobile: Make use of domain_alloc and domain_free
iommu/msm: Make use of domain_alloc and domain_free
iommu/tegra-gart: Make use of domain_alloc and domain_free
iommu/tegra-smmu: Make use of domain_alloc and domain_free
...
My Pengutronix address is not valid anymore, redirect people to the
Pengutronix kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The suspend scan rate value should not exceed 1000, unfortunately when
implementing the limit we used max_t instead of min_t, causing the value to
be at least 1000.
Signed-off-by: Dudley Du <dudl@cypress.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to Elan's firmware engineers we should not be subtracting 1 form
the raw number of x and y traces so that the pitch size is correct. For
example, if the touchpad x resolution is 2800 and x trace number is 20,
the pitch size of x should be 2800/20 = 140, not 2800/19 = 147.36.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When hover is detected report ABS_MT_DISTANCE as 1; for active contacts
the distance is reported as 0.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's zero-extend hardware id number when forming firmware file name,
to avoid kernel requesting firmware like "elants_i2c_ 0.bin", which
is quite unexpected.
Acked-by: Charlie Mooney<charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VAgA
-----END PGP SIGNATURE-----
Merge tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull final removal of deprecated cpus_* cpumask functions from Rusty Russell:
"This is the final removal (after several years!) of the obsolete
cpus_* functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack"
* tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
cpumask: remove __first_cpu / __next_cpu
cpumask: resurrect CPU_MASK_CPU0
linux/cpumask.h: add typechecking to cpumask_test_cpu
cpumask: only allocate nr_cpumask_bits.
Fix weird uses of num_online_cpus().
cpumask: remove deprecated functions.
mips: fix obsolete cpumask_of_cpu usage.
x86: fix more deprecated cpu function usage.
ia64: remove deprecated cpus_ usage.
powerpc: fix deprecated CPU_MASK_CPU0 usage.
CPU_MASK_ALL/CPU_MASK_NONE: remove from deprecated region.
staging/lustre/o2iblnd: Don't use cpus_weight
staging/lustre/libcfs: replace deprecated cpus_ calls with cpumask_
staging/lustre/ptlrpc: Do not use deprecated cpus_* functions
blackfin: fix up obsolete cpu function usage.
parisc: fix up obsolete cpu function usage.
tile: fix up obsolete cpu function usage.
arm64: fix up obsolete cpu function usage.
mips: fix up obsolete cpu function usage.
x86: fix up obsolete cpu function usage.
...
Pull more s390 updates from Martin Schwidefsky:
"The big thing in this second merge for s390 is the new eBPF JIT from
Michael which replaces the old 32-bit backend.
The remaining commits are bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: add locking for fmb access
s390/pci: extract software counters from fmb
s390/dasd: Fix unresumed device after suspend/resume having no paths
s390/dasd: fix unresumed device after suspend/resume
s390/dasd: fix inability to set a DASD device offline
s390/mm: Fix memory hotplug for unaligned standby memory
s390/bpf: Add s390x eBPF JIT compiler backend
s390: Use bool function return values of true/false not 1/0
Pull m68k fixes from Greg Ungerer:
"Nothing big, spelling fixes and fix/cleanup for ColdFire eth device setup"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix fec setup warning for ColdFire 5271 builds
m68knommu: ColdFire 5271 only has a single FEC controller
m68k: Fix trivial typos in comments
Yes, it should work, but it's a bad idea. Not only did ARM64 not have
the 16-bit access code (there's a separate patch to add it), it's just
not a good atomic type. Some architectures fundamentally don't do
atomic accesses in them (alpha), and it's not like it saves any space
here anyway because of structure packing issues.
We normally should aim for flags to be "unsigned int" or "unsigned
long". And if space is at a premium, use a single byte (although that
causes problems on alpha again). There might be very special cases
where a 16-byte entity is really wanted, but this is not one of them.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add handling of missed events in omap_dss_pm_notif which are
needed to support hibernation (suspend to disk).
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The doc refers to Documentation/devicetree/bindings/video/video-ports.txt
which does not exist. The documentation seems to be outdated and wants to
refer to Documentation/devicetree/bindings/graph.txt instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Joe Perches