Now that we have two callbacks s3c2412_i2s_get_clock & s3c64xx_i2s_get_clock
doing exactly the same thing, we can define one generic s3c_i2sv2_get_clock
and discard other two copies. Also, switch the users to make calls to the
newly defined and generic s3c_i2sv2_get_clock
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No need to keep redundant field iis_clk in s3c_i2sv2_info.
iis_cclk and iis_pclk is all we need.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Until now, s3c2412_get_iisclk would return NULL since iis_clk was never
initialized.
Return appropriate pointer as per the selection made for source clock.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The IMS field of s3c2412/13 is essentially the same as that of s3c64xx.
That is, the IISMOD[11] bit decides Master/Slave mode and IISMOD[10] bit
selects source clock for signal generation.
For that reason, remove improper defines for IISMOD[11:10] field mask
and define two 1bit fields that can be set independent of each other.
As a consequence, corresponding fields for PLAT_S3C64XX too get to use
these new defines.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Define more bit definitions in the order of mainline
support for the SoC.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The header for I2Sv2
linux/arch/arm/plat-s3c/include/plat/regs-s3c2412-iis.h
contains only controller specific definitions and nothing
SoC specific. So, it could be moved to sound/soc/s3c24xx/
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
BugLink: https://launchpad.net/bugs/541802
The OR's hardware distorts at PCM 100% because it does not correspond to
0 dB. Fix this in patch_cxt5045() for all Packard Bell models.
Reported-by: Valombre
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a quirk for all-in-one computer Dell Inspiron One 19 Touch to have proper
HP and Mic support.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We should disable irqs when we take the tu->qlock because it is used in
the irq handler. The only place that doesn't is
snd_timer_user_ccallback(). Most of the time snd_timer_user_ccallback()
is called with interrupts disabled but the the first ti->ccallback()
call in snd_timer_notify1() has interrupts enabled.
This was caught by lockdep which generates the following message:
> =================================
> [ INFO: inconsistent lock state ]
> 2.6.34-rc5 #5
> ---------------------------------
> inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
> dolphin/4003 [HC1[1]:SC0[0]:HE0:SE1] takes:
> (&(&tu->qlock)->rlock){?.+...}, at: [<f84ec472>] snd_timer_user_tinterrupt+0x28/0x132 [snd_timer]
> {HARDIRQ-ON-W} state was registered at:
> [<c1048de9>] __lock_acquire+0x654/0x1482
> [<c1049c73>] lock_acquire+0x5c/0x73
> [<c125ac3e>] _raw_spin_lock+0x25/0x34
> [<f84ec370>] snd_timer_user_ccallback+0x55/0x95 [snd_timer]
> [<f84ecc4b>] snd_timer_notify1+0x53/0xca [snd_timer]
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/549267
The OR verified that using the olpc-xo-1_5 model quirk allows the
headphones to be audible when inserted into the jack. Capture was
also verified to work correctly.
Reported-by: Richard Gagne
Tested-by: Richard Gagne
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/573284
The OR verified that using the olpc-xo-1_5 model quirk allows the
headphones to be audible when inserted into the jack. Capture was
also verified to work correctly.
Reported-by: Andy Couldrake <acouldrake@googlemail.com>
Tested-by: Andy Couldrake <acouldrake@googlemail.com>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes a problem where cards show up as only having a single mixer
element, suppressing all sound output.
Signed-off-by: Brian J. Tarricone <brian@tarricone.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both tpa6130a2, and tpa6140a2 is supported by the
same driver, but the gain dB scaling is different on
the amplifiers.
Provide different mixer control for the chips with correct
TLV mapping.
User space will see:
"TPA6130A2 Headphone Playback Volume" in case of 6130
"TPA6140A2 Headphone Playback Volume" in case of 6140
The way machine drivers are using this amplifier remained
the same.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Let the codec to hit OFF instead of STANDBY, when there is no activity.
When the codec is off, than the associated regulator can be also turned
off (if the number of users on the regulator is 0).
After initialization, the codec remains in power off, it is only turned
on for reading the ID registers (also testing the regulators).
The codec power is enabled, when the codec is moving from BIAS_OFF
to BIAS_STANDBY.
The codec is turned off, when it hits BIAS_OFF.
There are few scenarios, which has to be taken care::
1. Analog bypass caused BIAS_OFF -> BIAS_ON
We need to power on the codec, and do the chip init, but we does not
need to execute the playback related configuration
2. Playback caused BIAS_OFF -> BIAS_ON
We need to power on the codec, and do the chip init, and also we need
to execute the playback related configuration.
3. Playback start, while Analog bypass is on (BIAS_ON -> BIAS_ON)
We need to execute the playback related configuration. The codec is
already on.
4. Analog bypass enable, while playback (BIAS_ON -> BIAS_ON)
Nothing need to be done.
5. Playback start withing soc power down timeout (BIAS_ON -> BIAS_ON)
We need to execute the playback related configuration. The codec is
still on.
Since the power up, and the codec init is optimized, the added overhead
in stream start is minimal.
Withing this patch, the hard_power function is now only doing what it
supposed to: only handle the powers, and GPIO reset line.
The codec initialization and state restore has been moved out.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
As a preparation for supporting codec to be turned off,
when we are in BIAS_STANDBY.
The substream must be easily available in other places than
pcm_* callbacks.
Manage a pointer in _startup, and _shutdown for this.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Optimize the way how tlv320dac33 is powered uppon module and
soc initialization.
Also read the DAC33 ID registers, and update the reg_cache
to reflect it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
On power up we only need to initialize the codec, and
restore only registers, which are not in either in DAPM
nor in the playback start sequence.
These are mostly gain related registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
OUTL/R are leftovers from the original driver, and they
are no longer needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch orders the APLL and AIF power sequence in
case of HiFi (audio in TWL4030 terms) playback/capture.
We also need to make sure that the AIF is running during
playback/capture, when there is no valid DAPM route
available. For this purpose I introduce these virtual
widgets:
/* To have complete playback route all the time */
DAPM_OUTPUT("Virtual HiFi OUT") /* Will keep AIF/APLL enabled */
/* To have complete capture route all the time */
DAPM_INPUT("Virtual HiFi IN") /* Will keep AIF/APLL enabled */
/* To have complete playback route for the voice module */
DAPM_OUTPUT("Virtual Voice OUT") /* Will keep APLL enabled */
The DAPM_SUPPLY widgets for APLL and AIF are placed in a way,
that during any audio activity the needed configuration of AIF
and APLL will be enabled (playback, capture, analog loopback,
digital loopback, and voice activity).
The apll reference counting code has been lifted,
and modified from Liam Girdwood's earlier patch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This enables autoloading of the TXx9 sound driver on RBTX4927.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
To: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Linux MIPS Mailing List <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1101/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The WM9090 is a high performance low power audio subsystem, including
headphone and class D speaker drivers.
Note that this driver is a standalone CODEC driver and so is only
immediately suitable for use with the WM9090 as a standalone sound card
taking line inputs, or with a DAC with no software control. The pending
ASoC multi-CODEC support will expand the range of systems that can use
the driver, or system-specific adaptations can be made.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The SYSCLK source is automatically managed when configuring the PLL.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the TLV320AIC3x supplies and enables all of them for the
entire lifetime of the device.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Move PLL enable from BIAS_ON state to BIAS_PREPARE to be pair with
BIAS_STANDBY where PLL is disabled. Remove also old comments about power
control.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
These ADC, DAC and output pin power off commands are needless in
aic3x_set_bias_level since they are not enabled in aic3x_init and they are
defined in aic3x_dapm_widgets so the ASoC DAPM will take care of them
anyway.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for Philips UDA1345 CODEC. The CODEC has only
volume control, de-emphasis, mute, DC filtering and power control features.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Delay reporting for the three implemented DAC33 FIFO modes.
DAC33 has FIFO depth status register(s), but it can not be used, since
inside of pcm_pointer we can not send I2C commands.
Timestamp based estimation need to be used. The method of calculating
the delay depends on the active FIFO mode.
Bypass mode: FIFO is bypassed, report 0 as delay
Mode1: nSample fill mode. In this mode I need to use two timestamp
ts1: taken when the interrupt has been received
ts2: taken before writing to nSample register.
Interrupts are coming when DAC33 FIFO depth goes under alarm threshold.
Phase1: when we received the alarm threshold, but our workqueue has
not been executed (safeguard phase). Just count the played out
samples since ts1 and subtract it from the alarm threshold
value.
Phase2: During nSample burst (after writing to nSample register), count
the played out samples since ts1, count the samples received
since ts2 (in a burst). Estimate the FIFO depth using these and
alarm threshold value.
Phase3: Draining phase (after the burst read), count the played out
samples since ts1. Estimate the FIFO depth using the nSample
configuration and the alarm threshold value.
Mode7: Threshold based fill mode. In this mode one timestamp is enough.
ts1: taken when the interrupt has been received
Interrupts are coming when DAC33 FIFO depth reaches upper threshold.
Phase1: Draining phase (after the burst), counting the played out
samples since ts1, and subtract it from the upper threshold
value.
Phase2: During burst operation. Using the pre calculated time needed to
play out samples from the buffer during the drain period (from
upper to lower threshold), move the time window to cover the
estimated time from the burst start to the current time.
Calculate the samples played out since lower threshold and also
the samples received during the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When the DAC33 FIFO is in use the dai interface is running in
much higher speed than the sampling frequency.
Calculate the rate based on the internal base frequency and
the bclk divider.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Upper and Lower threshold values are used as magic
numbers. Replace them with defines for later use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is no need for calculations for FIFO bypass mode.
Just in case set the nsample maximum limit, which
has been done in the calculation phase.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Alarm threshold interrupt is triggered right after the
playback start.
This interrupt is recieved during the first burst period,
and caused the state machine to write additional nSample
command, which has to be avoided.
To fix this issue move the DAC33 interrupt unmasking
after we configured the PREFILL register with a small
delay.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is only one dma for the ESS ES968 based board.
Its index is 0 and not 1.
This make the es968 card working.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Follow the core jack implementation and allow reporting on the status
of NULL jacks, avoiding the need to check in detection implementations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The hardware volume handling code in essence just detects key presses, and
then does some hardcoded modification of the master volume based on which key
is pressed.
Clearly the right thing to do here is just report these keypresses to
userspace and let userspace decide what to with them.
This patch adds a Kconfig option which when enabled reports the volume
buttons as keypresses using an input device. When enabled this option
also gets rid of the ugly direct ac97 writes from the tasklet, the ac97lock
and the need for using a tasklet in general.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While working on the sound suspend / resume problems with my laptop
I noticed that the hardware volume handling code in essence just detects
key presses, and then does some hardcoded modification of the master volume
based on which key is pressed.
This made me think that clearly the right thing to do here is just report
these keypresses to userspace and let userspace decide what to with them.
This patch adds a Kconfig option which when enabled reports the volume
buttons as keypresses using an input device. When enabled this option
also gets rid of the ugly direct ac97 writes from the tasklet, the ac97lock
and the need for using a tasklet in general.
As an added bonus the keys now work identical to volume keys on a (usb)
keyboard with multimedia keys, providing visual feedback of the volume
level change, and a better range of the volume control (with a properly
configured desktop environment).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/568600
The OR has verified that the dell-m6 model quirk is necessary for audio
to be audible by default on the Dell Studio XPS 1645.
This change is necessary for 2.6.32.11 and 2.6.33.2 alike.
Reported-by: Andy Ross <andy@plausible.org>
Tested-by: Andy Ross <andy@plausible.org>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/459083
The OR has verified with 2.6.32.11 and the latest alsa-driver stable
daily snapshot that position_fix=1 is necessary for the external mic
to work and for PulseAudio not to crash constantly.
This patch is necessary also for 2.6.32.11 and 2.6.33.2.
Reported-by: <imwithid@yahoo.com>
Tested-by: <imwithid@yahoo.com>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While working on a fix for the volume being muted on the allegro in my
Compaq EVO N600C after suspend, I've learned a few things about the hardware
volume control worth documenting. The actual fix for the suspend / resume
issue is in the next patch in this set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ignore spurious HV interrupts during suspend / resume, this avoids
mistaking them for a mute button press. This is not very pretty but
it seems the only way to fix the master volume control gets muted
after suspend issue I'm seeing. Note that the es1968 driver is doing
exactly the same.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without this quirk sound stops working after suspend resume. With this quirk,
one still needs to manually unmute the master volume control after a suspend /
/ resume cycle. That is fixed in another patch in this set.
Note that this patch was submitted to the alsa bug tracker a long time ago:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4319
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CC: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/567494
The OR has verified that the existing model quirk, ALC880_UNIWILL,
is insufficient for audible playback and capture by default. Instead,
the ALC880_F1734 model quirk needs to be used.
This change is necessary for both 2.6.32.11 and 2.6.33.2.
Reported-by: Arnaud Malpeyre <amalpeyre@gmail.com>
Tested-by: Arnaud Malpeyre <amalpeyre@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/553002
The OR has verified that the dell-m6 model quirk is necessary for audio
to be audible by default on the Dell Studio XPS 1645.
This change is necessary for 2.6.32.11 and 2.6.33.2 alike.
Reported-by: Robert Chambers
Tested-by: Robert Chambers
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of AudioScience ASI boards.
The driver has been tested for years on alsa-driver external tree,
now finally got merged to the kernel.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use all the available Fratio values when configuring the WM8994 FLL, not
just 0 and 3, following more complete characterisation of the device
performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8994 FLL can be clocked from one of four inputs, the two MCLKs and
the LRCLK and BCLK of the AIF associated with the FLL. Allow all four
inputs to be used rather than defaulting to MCLK1.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
An index equal to the array size may not be accessed.
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When HP laptop with AD1981 codec is suspended and the docking-station
is connected before the resume, the outputs get confused, and wrongly
routed still to the speaker. This is because of a change in 2.6.34-rc1
ea52bf260e
ALSA: hda: Add powerdown for Analog Devices HDA codecs
The problem was the added resume callback that doesn't consider the
modified init hook. The fix is simply remove the resume callback here
and make the resume normally. This doesn't change any behavior intended
in the commit above (for shutting down the sound at suspend) but only
fixes the resume.
Reported-and-tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One of the features of the multi CODEC work is that it embeds a struct
device in the CODEC to provide diagnostics via a sysfs class rather than
via the device tree, at which point it's much better to use the struct
device private data rather than having two places to store it. Provide
an accessor function to allow this change to be made more easily, and
update all the CODEC drivers are updated.
To ensure use of the accessor the private data structure member is
renamed, meaning that if code developed with older an older core that
still uses private_data is merged it will fail to build.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Doing so causes a deadlock, so just signal the timer to stop
using an atomic variable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixed 8 checkpatch errors (ERROR: do not use assignment in if condition)
in sound/i2c/i2c.c.
Signed-off-by: Brian Waters <brianmwaters@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
attached please find a patch that adds support for at least the T410s
HDA codec. Most likely it will also add support for the T410 and T510
based models.
The patch was derived from Ideapad support. Support for the laptop's and
docking-station output connectors as well as the docking-station microphone
connector and the laptops internal devices has been tested. Since it has been
developed without a data-sheet available, support for digital outputs and the
laptop's microphone input may well be incorrect.
Microphone mute functionality is not included:
The microphone mute button seems to be reported through thinkpad_acpi key
0000101b. The mute button LED seems to be wired to thinkpad_acpi led
number 15.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Biostar mobo seems to give a wrong DMA position, resulting in
stuttering or skipping sounds on 2.6.34. Since the commit
7b3a177b0d, "ALSA: pcm_lib: fix "something
must be really wrong" condition", makes the position check more strictly,
the DMA position problem is revealed more clearly now.
The fix is to use only LPIB for obtaining the position, i.e. passing
position_fix=1. This patch adds a static quirk to achieve it as default.
Reported-by: Frank Griffin <ftg@roadrunner.com>
Cc: Eric Piel <Eric.Piel@tremplin-utc.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the matching model for Clevo laptop M570U.
Signed-off-by: Joerg Schirottke <master@kanotix.com>
Tested-by: Maximilian Gerhard <maxbox@directbox.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the notification of elapsed periods is not very exact.
Increase minimum periods to 4 as suggested by Liam Girdwood.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some VIA codecs have no multiple source selection for headphone pins,
thus it's useless (and wrong) to create "Independent HP" control on them.
This patch adds the check of connections to skip the control in such a
case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 5b0cb1d850
ALSA: hda - add more NID->Control mapping
breaks the control element allocation by returning a wrong value.
Let's fix it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set no_llseek to llseek file ops of each sound component (but for hwdep).
This avoids the implicit BKL invocation via generic_file_llseek() used
as default when fops.llseek is NULL.
Also call nonseekable_open() at each open ops to ensure the file flags
have no seek bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The llseek implementation is identical for existing driver implementations,
so let's merge to the common layer. The same code for the text proc file
can be used even for the binary proc file.
The driver can provide its own llseek method if needed. Then the common
code will be skipped.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the validity of the file position in the common info layer before
calling read or write callbacks in assumption that entry->size is set up
properly to indicate the max file size.
Removed the redundant checks from the callbacks as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 29a4f2d3 used writel() at offset 0x26 which is
half-word aligned causing unaligned exceptions on a
Cortex-A8. The original patch solved the "aaci-pl041 fpga:04:
ac97 read back fail" issue on a soft reset. Reading from any
arbitrary aaci register seems to solve this issue.
Signed-off-by: Philby John <pjohn@mvista.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for sound through the WM8750 codec on Zipit Z2.
Also, this patch incorporates support for detecting headset jack
insertion through the jack detection API.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sony VAIO models with ALC269 need to initialize the pin 0x19 to VREF
ground or Hi-Z to make the headphone working. Other than that, model=auto
works fine, so let's use model=auto with a specific fix-up table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few enhancement / fixes for fix-up table of some Realtek codecs:
- Apply fix-ups only for the auto model
- Apply additional verbs after normal init verbs
- Add a debug print to show the fix-up application
This is basically a preliminary work for the next fix for Sony VAIO.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
usb-midi causes sometimes Oops at snd_usbmidi_output_drain() after
disconnection. This is due to the access to the endpoints which have
been already released at disconnection while the files are still alive.
This patch fixes the problem by checking disconnection state at
snd_usbmidi_output_drain() and by releasing urbs but keeping the
endpoint instances until really all freed.
Tested-by: Tvrtko Ursulin <tvrtko@ursulin.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The widget connections of ADC of ALC880 and ALC2260 aren't initialized,
thus it might point to invalid pin. This can be a problem when mode=auto
and there is only one input pin. Then user can't change the connection
at all.
This patch adds the code to initialize the input pin connection of these
codecs.
Reference: Novell bnc#594363
https://bugzilla.novell.com/show_bug.cgi?id=594363
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Register the WM8750 as a SPI or I2C device. This patch mostly shuffles code
around. Hugely inspired by WM8753 which was already converted.
Also, this patch fixes the Jive and Spitz machine.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Corrected HP and mic pins for ALC269vb amic and dmic models.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC269vb has an alternative HP pin 0x21 in addition.
Fix the parser to recognize it.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use a local mutex instead of BKL. This should suffice since each device
type has also its open_mutex.
Also, a bit of clean-up of the legacy device auto-loading code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using a regular timer results in poll times < 1 jiffie with small
buffers, so we loaded the timer with the actual jiffie value. We can
be more accurate using a hrtimer. Also, we have to call
snd_pcm_period_elapsed after playing period_bytes and not
runtime->period_size (which is in samples and not in bytes).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When checking if we are DMA capable we have to check for the
IMX_SSI_DMA flag which is already set from platform_data instead
of setting it again when we want to do DMA.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@Slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: mixart: range checking proc file
ALSA: hda - Fix a wrong array range check in patch_realtek.c
ALSA: ASoC: move dma_data from snd_soc_dai to snd_soc_pcm_stream
ALSA: hda - Enable amplifiers on Acer Inspire 6530G
ASoC: Only do WM8994 bias off transition from standby
ASoC: Don't use DCS_DATAPATH_BUSY for WM hubs devices
ASoC: Don't do runtime wm_hubs DC servo updates if using offset correction
ASoC: Support second DC servo readback method for wm_hubs
ASoC: Avoid wraparound in wm_hubs DC servo correction
ALSA: echoaudio - Eliminate use after free
ALSA: i2c: cleanup: change parameter to pointer
ALSA: hda - Add MSI blacklist for Aopen MZ915-M
ASoC: OMAP: Fix capture pointer handling for OMAP1510 to work correctly with recent ALSA PCM code
ALSA: hda - Update document about MSI and interrupts
ALSA: hda: Fix 0 dB offset for Lenovo Thinkpad models using AD1981
ALSA: hda - Add missing printk argument in previous patch
ASoC: Fix passing platform_data to ac97 bus users and fix a leak
ALSA: hda - Fix ADC/MUX assignment of ALC269 codec
ALSA: hda - Fix invalid bit values passed to snd_hda_codec_amp_stereo()
ASoC: wm8994: playback => capture
This adds support for the Medion WIM2160 soundcard.
There's no PCI quirk added because it has the same PCI id as the
Medion MD2.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Assign DACs properly to each output. Currently, the front output is bound
to HP/speaker outputs blindly, but they should be assigned to individual
DACs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The original code doesn't take into consideration that the value of
MIXART_BA0_SIZE - pos can be less than zero which would lead to a large
unsigned value for "count".
Also I moved the check that read size is a multiple of 4 bytes below
the code that adjusts "count".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: <stable@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 6a4f2ccb46 introduced a wrong
comparision for the array range check, which effectively skips the whole
initialization of DAC connections. Fixed now.
Reference: bko#15689
https://bugzilla.kernel.org/show_bug.cgi?id=15689
Reported-by: Adrian Ulrich <kernel@blinkenlights.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Support interrupt based microphone bias detection. The WM8994 has two
microphone bias supplies, with detection supported on both. Detection
using GPIOs together with the standard GPIO based jack framework is
already supported via the platform data for the WM8994 core driver.
Note that as well as the microphone bias itself the system clock and
whichever AIF clock is supplying the system clock will need to be
enabled for detection to function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
[Note that this is a backported version for 2.6.34.
Upstream commit is fd23b7dee]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After more tests it appears that EAPD needs to be enabled
on both the 0x14 and 0x15 NIDs to enable the main speaker
and headphone amplifiers. The maximum volume setting is
now equal to what the machine achieves under other operating
systems.
Disabling Front or LFE playback triggers EAPD and disables
the amplifier. As such, these two playback switches have
been removed from the mixer.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise we may try to power down multiple times when the using
idle bias off and the driver is removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The DCS_DATAPATH_BUSY bit used to monitor the completion of DC servo
operations has been deprecated and with some more recente revisions
may perform incorrectly, especially when only analogue bypass paths
are in use. Switch to using readback from the DC servo command
register instead, which is supported for all devices. Without this
unacceptably long timeouts may be observed in some circumstances.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If we need to offset correct the DC servo then don't use runtime
recalibration since that is likely to introduce further offsets
which will be evident on powerdown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
More recent Wolfson hubs devices add the ability to read back the DC
servo calibration information from the register used to write offsets,
and later still ones remove the old readback registers. Add support
for the new scheme, and use it for WM8994 device revisions that
support it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the correction wraps around then a substantial offset would be
introduced.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Reverse headphone detection bit on PowerMac G4 Digital Audio (Tumbler).
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the call to snd_card_free in the error handling code at the end of the
function, as in the other error cases.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E2;
@@
snd_card_free(E)
...
(
E = E2
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We actually pass an array of 7 chars not 5.
This silences a smatch warning.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device needs MSI disablement. Added to the quirk list.
Reported-by: Harald Dunkel <harri@afaics.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With recent (2.6.34) chnages in PCM handling, capture stopped working on my
OMAP1510 based Amstrad Delta videophone.
Using 2.6.34-rc2, I was able to correct the problem in 3 different ways:
1. reverting commit 7b3a177b0d,
2. enabling additional jiffies check with
echo 4 >/proc/asound/card0/pcm0c0/xrun_debug
3. applying the patch below.
Since I wasn't able to reproduce the problem on my i686 PC, I guess the
problem is probably machine specific.
The patch reuses the method for software emulation of missing hardware
pointer, already implemented for playback on OMAP1510. It's possible that
event if a hardware pointer is available for capture on this machine, its
behaviour may be not compatible with what upper layer expects.
If you think the problem may be more general and should be solved differently,
on a higher level, I can try to work more on it if you give me a hint.
If the patch gets accepted, I suggest it goes as a fix in the current release
cycle.
Created and tested against linux-2.6.34-rc2.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
BugLink: https://launchpad.net/bugs/551606
The OR's hardware distorts at PCM 100% because it does not correspond to
0 dB. Fix this in patch_ad1981() for all models using the Thinkpad
quirk.
Reported-by: Jane Silber
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new helper, snd_hda_codec_update_cache(), for reducing the unneeded
verbs. This function checks the cached value and skips if it's identical
with the given one. Otherwise it works like snd_hda_codec_write_cache().
The alc269 code uses this function as an example.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some HP laptops have a mute LED that is controlled over the unused
MIC2 VREF pin. Implement the LED updater like patch_sigmatel.c for this
model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The way i've factored out the bus probe and removal functions so
that there's no code in the individual I2C and SPI functions means
that the register() and unregister() functions could just be squashed
into the bus_probe() and bus_remove() functions.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[The issue is an attempt to write the pdata without the AC97 device
allocated when using ac97.c - also added a comment in soc-core.c for the
special case for ac97. -- broonie]
Signed-off-by: Graham Gower <graham.gower@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC269 codec has a few different variants, and each of them may have
different ADC and MUX widgets. For example, one model has ADC 0x08
with MUX 0x23 while others has ADC 0x09 or ADC 0x07 with MUX 022 or
0x24. The difference of ADC appears usually as the capability of
the digital mic pin (0x12), and the current driver sometimes misses
the internal mic pin due to the mismatching ADC.
This patch adds a bit more clever way to find the matching ADC instead
of the static list. Now the driver checks all active input pins and
fills only the ADC/MUX's that contain all of them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mask and value parameters passed to snd_hda_codec_amp_stereo()
should be 8-bit values for mute and volume. Passing AMP_IN_MUTE() is
wrong, which is found in many places in patch_realtek.c as a left-over
from the conversion to snd_hda_codec_amp_stereo().
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=575669
The OR states that position_fix=1 is necessary to work around glitching
during volume adjustments using PulseAudio.
Reported-by: Carlos Laviola <claviola@debian.org>
Tested-by: Carlos Laviola <claviola@debian.org>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/481058
The OR has verified that both 'Headphone Jack Sense' and 'Line Jack Sense'
need to be muted for sound to be audible, so just add the machine's SSID
to the ac97 jack sense blacklist.
Reported-by: Richard Gagne
Tested-by: Richard Gagne
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert the device_terminate_all() operation on the
DMA engine to a generic device_control() operation
which can now optionally support also pausing and
resuming DMA on a certain channel. Implemented for the
COH 901 318 DMAC as an example.
[dan.j.williams@intel.com: update for timberdale]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Li Yang <leoli@freescale.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The commit 4d96eb255c broke the interrupt
time xrun functionality (stream stop etc.) if the CONFIG_SND_PCM_XRUN_DEBUG
is not set. This is because the xrun() is null defined without it.
Fix this by letting the function xrun() to be always defined as it was
before.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ARM-SHMOBILE series have FIFO-buffered serial interface 2 (FSI2)
device which is advanced version of FSI.
This patch add simple support for it.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The probe_only module parameter skips the codec initialization, too.
Remove the model=hwio code and use second bit in probe_only to
skip the HDA codec reset procedure.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
For Lenovo Thinkpad T61/X61, the analog beep input is connected
to node 0x20, index 3. Move the digital beep mute/volume controls
as "Digital Beep" and create analog beep controls for mentioned node.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Using the 'model=hwio' option, the driver bypasses any codec
initialization and the reset procedure for codecs is also
bypassed. This mode is usefull to enable direct access using
hwdep interface (using hdaverb or hda-analyzer tools) and
retain codec setup from BIOS.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
BugLink: https://launchpad.net/bugs/303789
This model needs both 'Headphone Jack Sense' and 'Line Jack Sense'
muted for audible audio, so just add its SSID to the blacklist and
don't enumerate the controls.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch add full duplex support on AT91 and AVR.
It was a bug: we needed to check first if there are some chips opened so we
could enable both reception and sending of the data.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch add AC97 support for ATMEL AT91, using the AVR32 code.
While AVR is using a DMA, the AT91 chips are using a Peripheral Data
Controller.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Skip initialization of connections of DAC widgets that aren't used,
which resulted in invalid verb parameters.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds basic support for M-Audio's Fast Track Ultra series of USB
audio interfaces. It is a refactored version of the patch Clemens
Ladisch posted some time ago. Neither playback nor capturing work
properly at 44100 Hz (don't know why).
The other sampling rates work properly. There's no support for the DSP
mixer, yet.
Signed-off-by: Felix Homann <fexpop@web.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sparse caught that initialize "playback" two times instead of
initializing "capture".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Bit operation for fsi_master should be done inside master lock.
But soft-reset/interrupt operation were outside of it.
This patch modify this problem.
It still allow to INT_ST outside-operation on fsi_interrupt,
but it is not problem.
Because this register doesn't need the bit operation.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the CMI8738 FRAME2 register is read, the chip sometimes (probably
when wrapping around) returns an invalid value that would be outside the
programmed DMA buffer. This leads to an inconsistent PCM pointer that is
likely to result in an underrun.
To work around this, read the register multiple times until we get a
valid value; the error state seems to be very short-lived.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Matija Nalis <mnalis-alsadev@voyager.hr>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add proper suspend/resume code for Terratec Aureon cards.
Based on ice1724 suspend/resume work of Igor Chernyshev.
Fixes bug https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4944
Tested on linux-2.6.32.9
Signed-off-by: Bernhard Urban <lewurm@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current ak4642 was not able to select pll.
This patch add support it.
It still expect PLL base input pin is MCKI.
see Table 5 "setting of PLL Mode" of datasheet
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This also adds the first DAI operation for AIF3 so fill out the ID and
the ops for that too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Now that the EHCI driver copes with small iso packets without blowing
up, take the snd-ua101 driver out of the alpha-test stage.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Don't force enable the microphone bias on WM8903 when doing jack
detection, and don't force enable microphone bias. This allows
platforms to only enable microphone detection when a jack has been
inserted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If no report is specified then disable detection. Note that we don't
disable the slow clock, though the power consumption from it should
be negligable. That should be reference counted, ideally through DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow machines to control exactly when the bias is turned on and off.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some systems, such as those with mechanical jack detection, may wish
to force enable a pin (typically mic bias) only some of the time.
Support such systems by having disable_pin() also coveer force enabled
pins.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some systems provide both mechanical and electrical detection of jack
status changes. On such systems power savings can be achieved by only
enabling the electrical detection methods when physical insertion has
been detected.
Begin supporting such systems by providing a notifier for jack status
changes which can be used to trigger any reconfiguration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Gain controls on outputs affect the power consumption
when the gain is set to non 0 value.
Outputs with amps have one register to configure the
routing and the gain:
PREDL_CTL (0x25):
bit 0: Voice enable
bit 1: Audio L1 enable
bit 2: Audio L2 enable
bit 3: Audio R2 enable
bit 4-5: Gain (0x0 - power down, 0x1 - 6dB, 0x2 - 0dB, 0x3 - -6dB)
bit 0 - 3: is handled in DAPM domain (DAPM_MIXER)
bit 4 - 5: has simple volume control
If there is no audio activity (BIAS_STANDBY), and
user changes the volume, than the output amplifier will
be enabled.
If the user changes the routing (but the codec remains in
BIAS_STANDBY), than the cached gain value also be written
to the register, which enables the amplifier.
The existing workaround for this is to have virtual
PGAs associated with the outputs, and whit DAPM PMD
the gain on the output will be forced to 0 (off) by
bypassing the regcache.
This failed to disable the amplifiers in several
scenario (as mentioned above).
Also if the codec is in BIAS_ON state, and user modifies
a volume control, which path is actually not enabled, than
that amplifier will be enabled as well, but it will
be not turned off, since there is no DAPM path, which
would make mute it.
To prevent amps being enabled, when they are not
needed, introduce the following workaround:
Track the state of each of this type of output.
In twl4030_write only allow actual write, when the
given output is enabled, otherwise only update
the reg_cache.
The PGA event handlers on power up will write the cached
value to the chip (restoring gain, routing selection).
On power down 0 is written to the register (disabling
the amp, and also just in case clearing the routing).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix build errors when CONFIG_PM is not enabled:
sound/usb/card.c:629: error: 'usb_audio_suspend' undeclared here (not in a function)
sound/usb/card.c:630: error: 'usb_audio_resume' undeclared here (not in a function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device does not have audio controllers and backlit buttons only.
Input data is handled over a dedicated USB endpoint.
All functions are supported by the driver now.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the device id for Nvidia GT220 cards to the nvhdmi
driver. I have tested it and confirmed it to be working.
Original patch download link:
https://gist.github.com/324070/
Signed-off-by: Derek Kelly <user.vdr@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/420578
The OR has verified that his hardware distorts because of the 0 dB
offset not corresponding to the highest PCM level. Fix this by capping
said PCM level to 0 dB similarly to what we do for CX20549 (Venice).
Reported-by: Mike Pontillo <pontillo@gmail.com>
Tested-by: Mike Pontillo <pontillo@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding this PCI quirk fixes the board config detection.
This also fixes jack sensing by using "hp_detect=1" via properly detected
board config.
Signed-off-by: Kunal Gangakhedkar <kunal.gangakhedkar@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The constant DMA_ACTIVE is defined with the dma_buffparams structure rather
than with the audio_operations structure. Takashi Iwai suggested that the
dmap_out field of the audio_operations structure should be used instead.
This is not tested.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If instantiation of a card failed, we still have to remove it from the
card list on unregistration. This fixes an Oops on Migo-R, triggering,
when after a failed firmware load attempt the driver modules are removed
and re-inserted again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes a warning ("pxa_free_dma: trying to free channel 0 which is
already freed") when a device was opened but the hw_params() call
failed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Note that since all the microphones share a bias there is a single
jack exported for all three, even though there are two physical
connectors plus the soldered down silicon mic. Note also that the SiMic
is always present by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The export is not needed since the per-bus code lives in the same
module.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Yi Li <yi.li@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initial version of TWL6040 codec driver.
The TWL6040 codec uses a proprietary PDM-based digital audio interface.
Audio paths supported are:
- Input: Main Mic, Sub Mic, Headset Mic, Auxiliary-FM Left/Right
- Output: Headset Left/Right, Handsfree Left/Right
TWL6040 codec supports power-up/down manual and automatic sequence.
Manual sequence is done through a specific register writes sequence.
Automatic sequence is done when the codec is powered-up through the
external AUDPWRON line. The completion of the sequence is signaled
through the audio interrupt.
TWL6040 codec sysclk can be provided by: low-power or high
performance PLL:
- The low-power PLL takes a low-frequency input at 32,768 Hz and
generates an approximate of 17.64 or 19.2 MHz (for 44.1 KHz and 48 KHz
respectively)
- The high-performance PLL generates an exact 19.2 MHz clock signal
from high-frequency input at 12/19.2/26/38.4 MHz.
Low-power playback mode is a special scenario where only headset path
(headset DAC and driver) is active.
For the particular case of headset path, PLL being used defines the
headset power mode: low-power, high-performance.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're keeping track of the number of times we've iterated but never
actually using this to bail out if the chip looks stuck.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
During validation of the internal clocking setup it has
been found that the following settings were not configured
in an optimal way:
ASRC_CTRL_A: SRCLKDIV was incorrect, instad of divide ratio 3,
ratio of 2 has to be used (as the comment stated)
DAC_CTRL_A: Fs = Fsref is the desired configuration instead of
Fs = Fsref / 1.5
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To make DSP_A mode working correctly the data delay should be
configured to 0. DSP_B mode thus can not be used with DAC33,
so remove it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Basic support for Left Justified coding for OMAP McBSP.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Indentation in initial support for McPDM driver was converted to spaces.
Use tabs to comply with open source coding-style.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added alc_codec_rename() helper for renaming codec->chip_name.
Added Acer-specific codec naming for ALC269/662.
[Clean-up and refactoring by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added alc_auto_parse_customize_define() to parse the Realtek-specific
attributes from SKU. Also enable beep controls only when the proper
attribute bit is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add new check for MIC. Do the internal DMIC as the Front MIC.
It could solve the default record source index issue.
[Fix the check properly using the bitmask by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I think this should be automatic pin instead of ping.
(but could be wrong).
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
sound: sequencer: clean up remove bogus check
ALSA: hda: Use LPIB and 6stack-dig for eMachines T5212
ALSA: hda - Disable MSI for Nvidia controller
ALSA: hda - Add PCI quirks for MSI NetOn AP1900 and Wind Top AE2220
ALSA: hda - Fix secondary ADC of ALC260 basic model
ALSA: hda - Add an error message for invalid mapping NID
ALSA: hda - New Intel HDA controller
The SIU ASoC driver must load firmware to program the DSP, therefore it
has to select FW_LOADER in its Kconfig entry.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The registers for AD193X are defined as 0x800-0x810 for spi which uses
16_8 mode, for i2c to support AD1937, we will use 8_8 mode, only the low
byte of 0x800-0x810 is valid. The patch will not destory other codecs,
but make soc cache interface more useful.
Signed-off-by: Barry Song <barry.song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Barry Song <barry.song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices provide support for detection of a small number of
buttons on their jacks. One common implementation provides a single
button, implemented by shorting the microphone to ground and detected
along with microphone presence detection by detecting varying current
draws on the microphone bias signal.
Provide support for up to three buttons via the jack interface. These
default to reporting BTN_n but an API is provided to allow these to
be remapped to other keys by the machine driver where it knows what
the keys are. More keys can be added with ease if required.
This is only intended to support simple accessory button designs. If
the interface is limiting then either creating a child device for the
accessory or accessing the input device in the jack directly is
recommended.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8750 is using some delayed work to manage the ramping of the bias
at startup and resume out of line from the normal flow. This predates
the support within ASoC core for moving the resume out of line from the
main system resume which provides equivalent functionality with better
interaction with applications. Change to doing the ramp in line to make
use of the core functionality.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A code audit reveals that there are currently no users of the widget
controls on PGAs. This is likely to continue to be the case since
while there are useful things that can be done with integrating the
PGA gain and mute controls with the power sequencing userspace
generally wants stereo controls for output stages which this doesn't
map onto well.
In preparation for implementing something more useful strip out the
existing code, leaving the parameters there for use by the new code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 provides microphone presence and short circuit detection.
Integrate this with the ASoC jack reporting API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8904 allows microphone detection signals to be brought out as
alternate functions of the GPIO signals which can be detected using
interrupt inputs on the CPU. Allow this to be configured using
platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide platform data allowing the configuration of the GPIO pins
on the WM8904 to be selected, allowing alternate functions to be
enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Support use of the WM8903 IRQ for reporting of microphone presence
and short detection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently used to detect completion of the write sequencer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide support for WM8903 microphone presence and short detection
using the GPIOs to route out a logic signal suitable for handling
using snd_soc_jack_add_gpios() on the processor GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow users to pass in a default configuration for the GPIOs of
the WM8903 as platform data. This allows configuration of the pin
muxing of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow pins to be forced on regardless of their power state. This is
intended for use with microphone bias supplies which need to be
enabled in order to support microphone detection - in systems without
appropriate hardware leaving the microphone unbiased when not in use
saves power.
The force done at power check time in order to avoid disrupting other
power detection logic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Jassi Brar