Merge reason: both topics modify the APIC code but were able to do it in
parallel so far. An upcoming patch generates a conflict so
merge them to avoid the conflict.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is a bit of micro-optimizations. But since the ring buffer is used
in tracing every function call, it is an extreme hot path. Every nanosecond
counts.
This change shows over 5% improvement in the ring-buffer-benchmark.
[ Impact: more efficient code ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The ring_buffer_time_stamp that is exported adds a little more overhead
than is needed for using it internally. This patch adds an internal
timestamp function that can be inlined (a single line function)
and used internally for the ring buffer.
[ Impact: a little less overhead to the ring buffer ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Doing some small changes in the fast path of the ring buffer recording
saves over 3% in the ring-buffer-benchmark test.
[ Impact: a little faster ring buffer recording ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
A long ago, in days of yore, it all began with a god named Thor.
There were vikings and boats and some plans for a Linux kernel
header. Unfortunately, a single 8-bit field was used for bootloader
type and version. This has generally worked without *too* much pain,
but we're getting close to flat running out of ID fields.
Add extension fields for both type and version. The type will be
extended if it the old field is 0xE; the version is a simple MSB
extension.
Keep /proc/sys/kernel/bootloader_type containing
(type << 4) + (ver & 0xf) for backwards compatiblity, but also add
/proc/sys/kernel/bootloader_version which contains the full version
number.
[ Impact: new feature to support more bootloaders ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The event length is calculated and passed in to rb_reserve_next_event
in two different locations. Having rb_reserve_next_event do the
calculations directly makes only one location to do the change and
causes the calculation to be inlined by gcc.
Before:
text data bss dec hex filename
16538 24 12 16574 40be kernel/trace/ring_buffer.o
After:
text data bss dec hex filename
16490 24 12 16526 408e kernel/trace/ring_buffer.o
[ Impact: smaller more efficient code ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The rb_reserve_next_event is only called for the data type (type = 0).
There is no reason to pass in the type to the function.
Before:
text data bss dec hex filename
16554 24 12 16590 40ce kernel/trace/ring_buffer.o
After:
text data bss dec hex filename
16538 24 12 16574 40be kernel/trace/ring_buffer.o
[ Impact: cleaner, smaller and slightly more efficient code ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Although we check if "missed" is not zero, we divide by hit + missed,
and the addition can possible overflow and become a divide by zero.
This patch checks for this case, and will report it when it happens
then modify "hit" to make the calculation be non zero.
[ Impact: prevent possible divide by zero in ring-buffer-benchmark ]
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The use of numeric constants is discouraged. It is cleaner and more
descriptive to use macros for constant time conversions.
This patch also removes an extra new line.
[ Impact: more descriptive time conversions ]
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
A compile warning triggered because we are calling
atomic_set(&counter->count). But since counter->count
is an atomic64_t, we have to use atomic64_set.
So the count can be set short, resulting in the reset ioctl
only resetting the low word.
[ Impact: clear counter properly during the reset ioctl ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <18951.48285.270311.981806@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The context-switch software counter gives inflated values at present
because each scheduler tick and each process-wide counter
enable/disable prctl gets counted as a context switch.
This happens because perf_counter_task_tick, perf_counter_task_disable
and perf_counter_task_enable all call perf_counter_task_sched_out,
which calls perf_swcounter_event to record a context switch event.
This fixes it by introducing a variant of perf_counter_task_sched_out
with two underscores in front for internal use within the perf_counter
code, and makes perf_counter_task_{tick,disable,enable} call it. This
variant doesn't record a context switch event, and takes a struct
perf_counter_context *. This adds the new variant rather than
changing the behaviour or interface of perf_counter_task_sched_out
because that is called from other code.
[ Impact: fix inflated context-switch event counts ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <18951.48034.485580.498953@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, if you have a group where the leader is disabled and there
are siblings that are enabled, and then you enable the leader, we only
put the leader on the PMU, and not its enabled siblings. This is
incorrect, since the enabled group members should be all on or all off
at any given point.
This fixes it by adding a call to group_sched_in in
__perf_counter_enable in the case where we're enabling a group leader.
To avoid the need for a forward declaration this also moves
group_sched_in up before __perf_counter_enable. The actual content of
group_sched_in is unchanged by this patch.
[ Impact: fix bug in counter enable code ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <18951.34946.451546.691693@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
struct request has had a few different ways to represent some
properties of a request. ->hard_* represent block layer's view of the
request progress (completion cursor) and the ones without the prefix
are supposed to represent the issue cursor and allowed to be updated
as necessary by the low level drivers. The thing is that as block
layer supports partial completion, the two cursors really aren't
necessary and only cause confusion. In addition, manual management of
request detail from low level drivers is cumbersome and error-prone at
the very least.
Another interesting duplicate fields are rq->[hard_]nr_sectors and
rq->{hard_cur|current}_nr_sectors against rq->data_len and
rq->bio->bi_size. This is more convoluted than the hard_ case.
rq->[hard_]nr_sectors are initialized for requests with bio but
blk_rq_bytes() uses it only for !pc requests. rq->data_len is
initialized for all request but blk_rq_bytes() uses it only for pc
requests. This causes good amount of confusion throughout block layer
and its drivers and determining the request length has been a bit of
black magic which may or may not work depending on circumstances and
what the specific LLD is actually doing.
rq->{hard_cur|current}_nr_sectors represent the number of sectors in
the contiguous data area at the front. This is mainly used by drivers
which transfers data by walking request segment-by-segment. This
value always equals rq->bio->bi_size >> 9. However, data length for
pc requests may not be multiple of 512 bytes and using this field
becomes a bit confusing.
In general, having multiple fields to represent the same property
leads only to confusion and subtle bugs. With recent block low level
driver cleanups, no driver is accessing or manipulating these
duplicate fields directly. Drop all the duplicates. Now rq->sector
means the current sector, rq->data_len the current total length and
rq->bio->bi_size the current segment length. Everything else is
defined in terms of these three and available only through accessors.
* blk_recalc_rq_sectors() is collapsed into blk_update_request() and
now handles pc and fs requests equally other than rq->sector update.
This means that now pc requests can use partial completion too (no
in-kernel user yet tho).
* bio_cur_sectors() is replaced with bio_cur_bytes() as block layer
now uses byte count as the primary data length.
* blk_rq_pos() is now guranteed to be always correct. In-block users
converted.
* blk_rq_bytes() is now guaranteed to be always valid as is
blk_rq_sectors(). In-block users converted.
* blk_rq_sectors() is now guaranteed to equal blk_rq_bytes() >> 9.
More convenient one is used.
* blk_rq_bytes() and blk_rq_cur_bytes() are now inlined and take const
pointer to request.
[ Impact: API cleanup, single way to represent one property of a request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement accessors - blk_rq_pos(), blk_rq_sectors() and
blk_rq_cur_sectors() which return rq->hard_sector, rq->hard_nr_sectors
and rq->hard_cur_sectors respectively and convert direct references of
the said fields to the accessors.
This is in preparation of request data length handling cleanup.
Geert : suggested adding const to struct request * parameter to accessors
Sergei : spotted error in patch description
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Ackec-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Rename cred_exec_mutex to reflect that it's a guard against foreign
intervention on a process's credential state, such as is made by ptrace(). The
attachment of a debugger to a process affects execve()'s calculation of the new
credential state - _and_ also setprocattr()'s calculation of that state.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Account for the initial offset to the jiffy count.
[ Impact: fix printk timestamps on architectures using fallback sched_clock() ]
Signed-off-by: Ron Lee <ron@debian.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix kprobes to lock text_mutex around some arch_arm/disarm_kprobe() which
are newly added by commit de5bd88d5a.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Other parts of the kernel may need to be able to enable or disable
specific events. Especially parts that create trace events.
[ Impact: allow enabling of trace events by those that create the event ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Commit 8f31bfe538
tracing/events: clean up for ftrace_set_clr_event()
Moved out the code for ftrace_set_clr_event into a helper funciton but
did not initialize the return value. As a result, we do not warn about
a typo in the echoing of events in set_event.
This patch restores the old warning:
# echo foobar > set_event
-bash: echo: write error: Invalid argument
[ Impact: restore warning of invalid entries to set_event ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Allow recording the CPU number the event was generated on.
RFC: this leaves a u32 as reserved, should we fill in the
node_id() there, or leave this open for future extention,
as userspace can already easily do the cpu->node mapping
if needed.
[ Impact: extend perfcounter output record format ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090508170029.008627711@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Much like CONFIG_RECORD_GROUP records the hw_event.config to
identify the values, allow to record this for all counters.
[ Impact: extend perfcounter output record format ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090508170028.923228280@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Corey noticed that ioctl()s on grouped counters didn't work on
the whole group. This extends the ioctl() interface to take a
second argument that is interpreted as a flags field. We then
provide PERF_IOC_FLAG_GROUP to toggle the behaviour.
Having this flag gives the greatest flexibility, allowing you
to individually enable/disable/reset counters in a group, or
all together.
[ Impact: fix group counter enable/disable semantics ]
Reported-by: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090508170028.837558214@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
perf_counter_task_tick() does way too much work to find out
there's nothing to do. Provide an easy short-circuit for the
normal case where there are no counters on the system.
[ Impact: micro-optimization ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090508170028.750619201@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A smarter way to figure out the output of an enable file.
[ Impact: clean up ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A0399A5.2080603@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a helper function __ftrace_set_clr_event(), and replace some
ftrace_set_clr_event() calls with this helper, thus we don't need any
kstrdup() or kmalloc().
As a side effect, this patch fixes an issue in self tests code, which is
similar to the one fixed in commit d6bf81ef0f
("tracing: append ":*" to internal setting of system events")
It's a small issue and won't cause any bug in fact, but we should do things
right anyway.
[ Impact: prevent spurious event-enabling in tracing self-tests ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A03998E.3020503@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
arch/frv/include/asm/pgtable.h
arch/x86/include/asm/required-features.h
arch/x86/xen/mmu.c
Merge reason: x86/xen was on a .29 base still, move it to a fresher
branch and pick up Xen fixes as well, plus resolve
conflicts
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There's a WARN_ON in the ring buffer code that makes sure preemption
is disabled. It checks "!preempt_count()". But when CONFIG_PREEMPT is not
enabled, preempt_count() is always zero, and this will trigger the warning.
[ Impact: prevent false warning on non preemptible kernels ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
It is nice to see the overhead of the benchmark test when tracing is
disabled. That is, we turn off the ring buffer just to see what the
cost of running the loop that calls into the ring buffer is.
Currently, if no entries wer made, we get 0. This is not informative.
This patch changes it to check if we had any "missed" (non recorded)
events. If so, a total count is also reported.
[ Impact: evaluate the over head of the ring buffer benchmark test ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Calling cond_resched at every iteration of the loop adds a bit of
overhead to the benchmark.
This patch does two things.
1) only calls cond-resched when CONFIG_PREEMPT is not enabled
2) only calls cond-resched after so many traces has been performed.
[ Impact: less overhead to the ring-buffer-benchmark ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Tracing can be very helpful to debug the kernel. When DEBUG_KERNEL is
enabled it is nice to enable the trace menu as well.
This patch only make the tracing menu enabled by default, it does not
make any of the tracers enabled. And the menu is only enabled by
default if DEBUG_KERNEL is enabled.
[ Impact: show tracing options to those debugging the kernel ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The system enabling of events uses the same code as the set_event file.
It passes in the name of the system to the parser and that will enable
all the events that has that system as a name.
The problem is that it will also enable events with the same name as the
system.
If you have system name foo, and system name bar, but within the system
bar, there exists an event called foo. By setting the system name foo,
you will also be enabling the event foo in the system bar. This is not
an expected result.
The solution is to pass in "foo:*", which will only enable the system
foo and not events called foo.
[ Impact: prevent accidental enabling of events with same name as a system ]
Reported-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Ingo Molnar thought that the code to calculate the time in cond_resched
is a bit too ugly and is not needed. This patch removes it and replaces
it with a simple call to cond_resched. I kept the comment that explains
the reason for the cond_resched.
[ Impact: remove ugly code ]
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Merge reason: this topic is ready for upstream now. It passed
Oleg's review and Andrew had no further mm/*
objections/observations either.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: tracing/core was on a .30-rc1 base and was missing out on
on a handful of tracing fixes present in .30-rc5-almost.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In filter_add_subsystem_pred() we should release event_mutex before
calling filter_free_subsystem_preds(), since both functions hold
event_mutex.
[ Impact: fix deadlock when writing invalid pred into subsystem filter ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: tzanussi@gmail.com
Cc: a.p.zijlstra@chello.nl
Cc: fweisbec@gmail.com
Cc: rostedt@goodmis.org
LKML-Reference: <4A028993.7020509@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When we set a filter for an event, such as:
echo "name == my_lock_name" > \
/debug/tracing/events/lockdep/lock_acquired/filter
then the following order of token type is parsed:
- space
- operator
- parentheses
- operand
Because the operators and parentheses have a higher precedence
than the operand characters, which is normal, then we can't
use any string containing such special characters:
()=<>!&|
To get this support and also avoid ambiguous intepretation from
the parser or the human, we can do it using double quotes so that
we keep the usual languages habits.
Then after this patch you can still declare string condition like
before:
echo name == myname
But if you want to compare against a string containing an operator
character, you can use double quotes:
echo 'name == "&myname"'
Don't forget to include the whole expression into single quotes or
the double ones will be eaten by echo.
[ Impact: support strings with special characters for tracing filters ]
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Zhaolei <zhaolei@cn.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Currently the filtering infrastructure supports well the
numeric types and fixed sized array types.
But the recently added __string() field uses a specific
indirect offset mechanism which requires a specific
predicate. Until now it wasn't supported.
This patch adds this support and implies very few changes,
only a new predicate is needed, the management of this specific
field can be done through the usual string helpers in the
filtering infrastructure.
[ Impact: support all kinds of strings in the tracing filters ]
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Zhaolei <zhaolei@cn.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
When a thread is oom killed and fails to exit, it's helpful to know which
threads have access to memory reserves if the machine livelocks. This is
done by testing for the TIF_MEMDIE thread info flag and should be
displayed alongside stack traces to identify tasks that have access to
such reserves but are still stuck allocating pages, for instance.
It would probably be helpful in other cases as well, so all thread info
flags are emitted when showing a task.
( v2: fix warning reported by Stephen Rothwell )
[ Impact: extend debug printout info ]
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <alpine.DEB.2.00.0905040136390.15831@chino.kir.corp.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With the current event directory, you can only enable individual events.
The file debugfs/tracing/set_event is used to be able to enable or
disable several events at once. But that can still be awkward.
This patch adds hierarchical enabling of events. That is, each directory
in debugfs/tracing/events has an "enable" file. This file can enable
or disable all events within the directory and below.
# echo 1 > /debugfs/tracing/events/enable
will enable all events.
# echo 1 > /debugfs/tracing/events/sched/enable
will enable all events in the sched subsystem.
# echo 1 > /debugfs/tracing/events/enable
# echo 0 > /debugfs/tracing/events/irq/enable
will enable all events, but then disable just the irq subsystem events.
When reading one of these enable files, there are four results:
0 - all events this file affects are disabled
1 - all events this file affects are enabled
X - there is a mixture of events enabled and disabled
? - this file does not affect any event
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Li Zefan found that there's a race using the event ids of events and
modules. When a module is loaded, an event id is incremented. We only
have 16 bits for event ids (65536) and there is a possible (but highly
unlikely) race that we could load and unload a module that registers
events so many times that the event id counter overflows.
When it overflows, it then restarts and goes looking for available
ids. An id is available if it was added by a module and released.
The race is if you have one module add an id, and then is removed.
Another module loaded can use that same event id. But if the old module
still had events in the ring buffer, the new module's call back would
get bogus data. At best (and most likely) the output would just be
garbage. But if the module for some reason used pointers (not recommended)
then this could potentially crash.
The safest thing to do is just reset the ring buffer if a module that
registered events is removed.
[ Impact: prevent unpredictable results of event id overflows ]
Reported-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <49FEAFD0.30106@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When building with gcc 3.2 I get thousands of warnings such as
include/linux/gfp.h: In function `allocflags_to_migratetype':
include/linux/gfp.h:105: warning: null format string
due to passing a NULL format string to warn_slowpath() in
#define __WARN() warn_slowpath(__FILE__, __LINE__, NULL)
Split this case out into a separate call. This also shrinks the kernel
slightly:
text data bss dec hex filename
4802274 707668 712704 6222646 5ef336 vmlinux
text data bss dec hex filename
4799027 703572 712704 6215303 5ed687 vmlinux
due to removeing one argument from the commonly-called __WARN().
[akpm@linux-foundation.org: reduce scope of `empty']
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is what we believe to be a false positive reported by lockdep.
inotify_inode_queue_event() => take inotify_mutex => kernel_event() =>
kmalloc() => SLOB => alloc_pages_node() => page reclaim => slab reclaim =>
dcache reclaim => inotify_inode_is_dead => take inotify_mutex => deadlock
The plan is to fix this via lockdep annotation, but that is proving to be
quite involved.
The patch flips the allocation over to GFP_NFS to shut the warning up, for
the 2.6.30 release.
Hopefully we will fix this for real in 2.6.31. I'll queue a patch in -mm
to switch it back to GFP_KERNEL so we don't forget.
=================================
[ INFO: inconsistent lock state ]
2.6.30-rc2-next-20090417 #203
---------------------------------
inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
kswapd0/380 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&inode->inotify_mutex){+.+.?.}, at: [<ffffffff8112f1b5>] inotify_inode_is_dead+0x35/0xb0
{RECLAIM_FS-ON-W} state was registered at:
[<ffffffff81079188>] mark_held_locks+0x68/0x90
[<ffffffff810792a5>] lockdep_trace_alloc+0xf5/0x100
[<ffffffff810f5261>] __kmalloc_node+0x31/0x1e0
[<ffffffff81130652>] kernel_event+0xe2/0x190
[<ffffffff81130826>] inotify_dev_queue_event+0x126/0x230
[<ffffffff8112f096>] inotify_inode_queue_event+0xc6/0x110
[<ffffffff8110444d>] vfs_create+0xcd/0x140
[<ffffffff8110825d>] do_filp_open+0x88d/0xa20
[<ffffffff810f6b68>] do_sys_open+0x98/0x140
[<ffffffff810f6c50>] sys_open+0x20/0x30
[<ffffffff8100c272>] system_call_fastpath+0x16/0x1b
[<ffffffffffffffff>] 0xffffffffffffffff
irq event stamp: 690455
hardirqs last enabled at (690455): [<ffffffff81564fe4>] _spin_unlock_irqrestore+0x44/0x80
hardirqs last disabled at (690454): [<ffffffff81565372>] _spin_lock_irqsave+0x32/0xa0
softirqs last enabled at (690178): [<ffffffff81052282>] __do_softirq+0x202/0x220
softirqs last disabled at (690157): [<ffffffff8100d50c>] call_softirq+0x1c/0x50
other info that might help us debug this:
2 locks held by kswapd0/380:
#0: (shrinker_rwsem){++++..}, at: [<ffffffff810d0bd7>] shrink_slab+0x37/0x180
#1: (&type->s_umount_key#17){++++..}, at: [<ffffffff8110cfbf>] shrink_dcache_memory+0x11f/0x1e0
stack backtrace:
Pid: 380, comm: kswapd0 Not tainted 2.6.30-rc2-next-20090417 #203
Call Trace:
[<ffffffff810789ef>] print_usage_bug+0x19f/0x200
[<ffffffff81018bff>] ? save_stack_trace+0x2f/0x50
[<ffffffff81078f0b>] mark_lock+0x4bb/0x6d0
[<ffffffff810799e0>] ? check_usage_forwards+0x0/0xc0
[<ffffffff8107b142>] __lock_acquire+0xc62/0x1ae0
[<ffffffff810f478c>] ? slob_free+0x10c/0x370
[<ffffffff8107c0a1>] lock_acquire+0xe1/0x120
[<ffffffff8112f1b5>] ? inotify_inode_is_dead+0x35/0xb0
[<ffffffff81562d43>] mutex_lock_nested+0x63/0x420
[<ffffffff8112f1b5>] ? inotify_inode_is_dead+0x35/0xb0
[<ffffffff8112f1b5>] ? inotify_inode_is_dead+0x35/0xb0
[<ffffffff81012fe9>] ? sched_clock+0x9/0x10
[<ffffffff81077165>] ? lock_release_holdtime+0x35/0x1c0
[<ffffffff8112f1b5>] inotify_inode_is_dead+0x35/0xb0
[<ffffffff8110c9dc>] dentry_iput+0xbc/0xe0
[<ffffffff8110cb23>] d_kill+0x33/0x60
[<ffffffff8110ce23>] __shrink_dcache_sb+0x2d3/0x350
[<ffffffff8110cffa>] shrink_dcache_memory+0x15a/0x1e0
[<ffffffff810d0cc5>] shrink_slab+0x125/0x180
[<ffffffff810d1540>] kswapd+0x560/0x7a0
[<ffffffff810ce160>] ? isolate_pages_global+0x0/0x2c0
[<ffffffff81065a30>] ? autoremove_wake_function+0x0/0x40
[<ffffffff8107953d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff810d0fe0>] ? kswapd+0x0/0x7a0
[<ffffffff8106555b>] kthread+0x5b/0xa0
[<ffffffff8100d40a>] child_rip+0xa/0x20
[<ffffffff8100cdd0>] ? restore_args+0x0/0x30
[<ffffffff81065500>] ? kthread+0x0/0xa0
[<ffffffff8100d400>] ? child_rip+0x0/0x20
[eparis@redhat.com: fix audit too]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ring buffer benchmark/test runs a producer for 10 seconds.
This is done with preemption and interrupts enabled. But if the kernel
is not compiled with CONFIG_PREEMPT, it basically stops everything
but interrupts for 10 seconds.
Although this is just a test and is not for production, this attribute
can be quite annoying. It can also spawn badness elsewhere.
This patch solves the issues by calling "cond_resched" when the system
is not compiled with CONFIG_PREEMPT. It also keeps track of the time
spent to call cond_resched such that it does not go against the
time calculations. That is, if the task schedules away, the time scheduled
out is removed from the test data. Note, this only works for non PREEMPT
because we do not know when the task is scheduled out if we have PREEMPT
enabled.
[ Impact: prevent test from stopping the world for 10 seconds ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Ingo Molnar thought the code would be cleaner if we used a function call
instead of a goto for moving the tail page. After implementing this,
it seems that gcc still inlines the result and the output is pretty much
the same. Since this is considered a cleaner approach, might as well
implement it.
[ Impact: code clean up ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The result of the allocation of the ring buffer read page in the
ring buffer bench mark does not check the return to see if a page
was actually allocated. This patch fixes that.
[ Impact: avoid NULL dereference ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The code in __rb_reserve_next checks on page overflow if it is the
original commiter and then resets the page back to the original
setting. Although this is fine, and the code is correct, it is
a bit fragil. Some experimental work I did breaks it easily.
The better and more robust solution is to have all commiters that
overflow the page, simply subtract what they added.
[ Impact: more robust ring buffer account management ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This compiler warning:
CC kernel/trace/trace_output.o
kernel/trace/trace_output.c: In function ‘register_ftrace_event’:
kernel/trace/trace_output.c:544: warning: ‘list’ may be used uninitialized in this function
Is wrong as 'list' is always initialized - but GCC (4.3.2) does not
recognize this relationship properly.
Work around the warning by initializing the variable to NULL.
[ Impact: fix false positive compiler warning ]
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This attempts to clarify names utilized during block I/O remap
operations (partition, volume manager). It correctly matches up the
/from/ information for both device & sector. This takes in the concept
from Kosaki Motohiro and extends it to include better naming for the
"device_from" field.
[ Impact: cleanup ]
Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <49FF4FAE.3000301@hp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The orig_cpu parameter in trace_sched_migrate_task() is not necessary,
it can be got by using task_cpu(p) in the probe.
[ Impact: micro-optimization ]
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
[ modified from Mathieu's patch. The original patch is at:
http://marc.info/?l=linux-kernel&m=123791201716239&w=2 ]
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Cc: fweisbec@gmail.com
Cc: rostedt@goodmis.org
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: zhaolei@cn.fujitsu.com
Cc: laijs@cn.fujitsu.com
LKML-Reference: <49FFFDB7.1050402@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A module will add/remove its trace events when it gets loaded/unloaded, so
the ftrace_events list is not "const", and concurrent access needs to be
protected.
This patch thus fixes races between loading/unloding modules and read
'available_events' or read/write 'set_event', etc.
Below shows how to reproduce the race:
# for ((; ;)) { cat /mnt/tracing/available_events; } > /dev/null &
# for ((; ;)) { insmod trace-events-sample.ko; rmmod sample; } &
After a while:
BUG: unable to handle kernel paging request at 0010011c
IP: [<c1080f27>] t_next+0x1b/0x2d
...
Call Trace:
[<c10c90e6>] ? seq_read+0x217/0x30d
[<c10c8ecf>] ? seq_read+0x0/0x30d
[<c10b4c19>] ? vfs_read+0x8f/0x136
[<c10b4fc3>] ? sys_read+0x40/0x65
[<c1002a68>] ? sysenter_do_call+0x12/0x36
[ Impact: fix races when concurrent accessing ftrace_events list ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4A00F709.3080800@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When unloading a module, memory allocated by init_preds() and
trace_define_field() is not freed.
[ Impact: fix memory leak ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <4A00F6E0.3040503@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: we moved a mutex.h commit that originated from the
perfcounters tree into core/locking - but now merge
back that branch to solve a merge artifact and to
pick up cleanups of this commit that happened in
core/locking.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds code that can benchmark the ring buffer as well as
test it. This code can be compiled into the kernel (not recommended)
or as a module.
A separate ring buffer is used to not interfer with other users, like
ftrace. It creates a producer and a consumer (option to disable creation
of the consumer) and will run for 10 seconds, then sleep for 10 seconds
and then repeat.
While running, the producer will write 10 byte loads into the ring
buffer with just putting in the current CPU number. The reader will
continually try to read the buffer. The reader will alternate from reading
the buffer via event by event, or by full pages.
The output is a pr_info, thus it will fill up the syslogs.
Starting ring buffer hammer
End ring buffer hammer
Time: 9000349 (usecs)
Overruns: 12578640
Read: 5358440 (by events)
Entries: 0
Total: 17937080
Missed: 0
Hit: 17937080
Entries per millisec: 1993
501 ns per entry
Sleeping for 10 secs
Starting ring buffer hammer
End ring buffer hammer
Time: 9936350 (usecs)
Overruns: 0
Read: 28146644 (by pages)
Entries: 74
Total: 28146718
Missed: 0
Hit: 28146718
Entries per millisec: 2832
353 ns per entry
Sleeping for 10 secs
Time: is the time the test ran
Overruns: the number of events that were overwritten and not read
Read: the number of events read (either by pages or events)
Entries: the number of entries left in the buffer
(the by pages will only read full pages)
Total: Entries + Read + Overruns
Missed: the number of entries that failed to write
Hit: the number of entries that were written
The above example shows that it takes ~353 nanosecs per entry when
there is a reader, reading by pages (and no overruns)
The event by event reader slowed the producer down to 501 nanosecs.
[ Impact: see how changes to the ring buffer affect stability and performance ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In the hot path of the ring buffer "__rb_reserve_next" there's a big
if statement that does not even return back to the work flow.
code;
if (cross to next page) {
[ lots of code ]
return;
}
more code;
The condition is even the unlikely path, although we do not denote it
with an unlikely because gcc is fine with it. The condition is true when
the write crosses a page boundary, and we need to start at a new page.
Having this if statement makes it hard to read, but calling another
function to do the work is also not appropriate, because we are using a lot
of variables that were set before the if statement, and we do not want to
send them as parameters.
This patch changes it to a goto:
code;
if (cross to next page)
goto next_page;
more code;
return;
next_page:
[ lots of code]
This makes the code easier to understand, and a bit more obvious.
The output from gcc is practically identical. For some reason, gcc decided
to use different registers when I switched it to a goto. But other than that,
the logic is the same.
[ Impact: easier to read code ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When adding the EXPORT_SYMBOL to some of the tracing API, I accidently
used EXPORT_SYMBOL instead of EXPORT_SYMBOL_GPL. This patch fixes
that mistake.
[ Impact: export the tracing code only for GPL modules ]
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As a precaution, it is best to disable writing to the ring buffers
when reseting them.
[ Impact: prevent weird things if write happens during reset ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In the swap page ring buffer code that is used by the ftrace splice code,
we scan the page to increment the counter of entries read.
With the number of entries already in the page we simply need to add it.
[ Impact: speed up reading page from ring buffer ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'irq/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Revert "genirq: assert that irq handlers are indeed running in hardirq context"
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: x86, mmiotrace: fix range test
tracing: fix ref count in splice pages
Currently, when the ring buffer writer overflows the buffer and must
write over non consumed data, we increment the overrun counter by
reading the entries on the page we are about to overwrite. This reads
the entries one by one.
This is not very effecient. This patch adds another entry counter
into each buffer page descriptor that keeps track of the number of
entries on the page. Now on overwrite, the overrun counter simply
needs to add the number of entries that is on the page it is about
to overwrite.
[ Impact: speed up of ring buffer in overwrite mode ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As a kernel thread, rcu_sched_grace_period() runs with all signals ignored.
It can never receive a signal even if it sleeps in TASK_INTERRUPTIBLE, it
needs the explicit allow_signal() to be visible for signals.
[ Impact: reduce kernel size, remove dead code ]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <20090503211118.GA22973@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The entries counter in cpu buffer is not atomic. It can be updated by
other interrupts or from another CPU (readers).
But making entries into "atomic_t" causes an atomic operation that can
hurt performance. Instead we convert it to a local_t that will increment
a counter with a local CPU atomic operation (if the arch supports it).
Instead of fighting with readers and overwrites that decrement the counter,
I added a "read" counter. Every time a reader reads an entry it is
incremented.
We already have a overrun counter and with that, the entries counter and
the read counter, we can calculate the total number of entries in the
buffer with:
(entries - overrun) - read
As long as the total number of entries in the ring buffer is less than
the word size, this will work. But since the entries counter was previously
a long, this is no different than what we had before.
Thanks to Andrew Morton for pointing out in the first version that
atomic_t does not replace unsigned long. I switched to atomic_long_t
even though it is signed. A negative count is most likely a bug.
[ Impact: keep accurate count of cpu buffer entries ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Redirect the output to the parent counter and put in some sanity checks.
[ Impact: new perfcounter feature - inherited sampling counters ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090505155437.331556171@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use -1 instead of 0 as unlocked, since 0 is a valid cpu number.
( This is not an issue right now but will be once we allow multiple
counters to output to the same mmap area. )
[ Impact: prepare code for multi-counter profile output ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090505155437.232686598@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Provide a threshold to relax the mlock accounting, increasing usability.
Each counter gets perf_counter_mlock_kb for free.
[ Impact: allow more mmap buffering ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090505155437.112113632@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Provide a way to reset an existing counter - this eases PAPI
libraries around perfcounters.
Similar to read() it doesn't collapse pending child counters.
[ Impact: new perfcounter fd ioctl method to reset counters ]
Suggested-by: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090505155437.022272933@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Keep data_head up-to-date irrespective of notifications. This fixes
the case where you disable a counter and don't get a notification for
the last few pending events, and it also allows polling usage.
[ Impact: increase precision of perfcounter mmap-ed fields ]
Suggested-by: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090505155436.925084300@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thomas noted that we should disallow sysctl_sched_rt_runtime == 0 for
(!RT_GROUP) since the root group always has some RT tasks in it.
Further, update the documentation to inspire clue.
[ Impact: exclude corner-case sysctl_sched_rt_runtime value ]
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090505155436.863098054@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds stats to the ftrace ring buffers:
# cat /debugfs/tracing/per_cpu/cpu0/stats
entries: 42360
overrun: 30509326
commit overrun: 0
nmi dropped: 0
Where entries are the total number of data entries in the buffer.
overrun is the number of entries not consumed and were overwritten by
the writer.
commit overrun is the number of entries dropped due to nested writers
wrapping the buffer before the initial writer finished the commit.
nmi dropped is the number of entries dropped due to the ring buffer
lock being held when an nmi was going to write to the ring buffer.
Note, this field will be meaningless and will go away when the ring
buffer becomes lockless.
[ Impact: let userspace know what is happening in the ring buffers ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The WARN_ON in the ring buffer when a commit is preempted and the
buffer is filled by preceding writes can happen in normal operations.
The WARN_ON makes it look like a bug, not to mention, because
it does not stop tracing and calls printk which can also recurse, this
is prone to deadlock (the WARN_ON is not in a position to recurse).
This patch removes the WARN_ON and replaces it with a counter that
can be retrieved by a tracer. This counter is called commit_overrun.
While at it, I added a nmi_dropped counter to count any time an NMI entry
is dropped because the NMI could not take the spinlock.
[ Impact: prevent deadlock by printing normal case warning ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
I'm adding a module to do a series of tests on the ring buffer as well
as benchmarks. This module needs to have more of the ring buffer API
exported. There's nothing wrong with reading the ring buffer from a
module.
[ Impact: allow modules to read pages from the ring buffer ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Now percpu counters can be initialized very early. But the init
sequence uses mutex_lock(). Fortunately, perf_resource_mutex should
be a spinlock anyway, so convert it.
[ Impact: fix crash due to early init mutex use ]
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
percpu scheduling for perfcounters wants to take the context lock,
but that lock first needs to be initialized. Currently it is an
early_initcall() - but that is too late, the task tick runs much
sooner than that.
Call it explicitly from the scheduler init sequence instead.
[ Impact: fix access-before-init crash ]
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This used to be unstable when we had the rq->lock dependencies,
but now that they are that of the past we can turn on percpu
counter RR too.
[ Impact: handle counter over-commit for per-CPU counters too ]
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some arches don't supply their own clocksource. This is mainly the
case in architectures that get their inter-tick times by reading the
counter on their interval timer. Since these timers wrap every tick,
they're not really useful as clocksources. Wrapping them to act like
one is possible but not very efficient. So we provide a callout these
arches can implement for use with the jiffies clocksource to provide
finer then tick granular time.
[ Impact: ease the migration to generic time keeping ]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Setup clocksource mult_orig in clocksource_enable().
Clocksource drivers can save power by using keeping the
device clock disabled while the clocksource is unused.
In practice this means that the enable() and disable()
callbacks perform clk_enable() and clk_disable().
The enable() callback may also use clk_get_rate() to get
the clock rate from the clock framework. This information
can then be used to calculate the shift and mult variables.
Currently the mult_orig variable is setup from mult at
registration time only. This is conflicting with the above
case since the clock is disabled and the mult variable is
not yet calculated at the time of registration.
Moving the mult_orig setup code to clocksource_enable()
allows us to both handle the common case with no enable()
callback and the mult-changed-after-enable() case.
[ Impact: allow dynamic clock source usage ]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090501054546.8193.10688.sendpatchset@rx1.opensource.se>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
tick_handle_periodic() can lock up hard when a one shot clock event
device is used in combination with jiffies clocksource.
Avoid an endless loop issue by requiring that a highres valid
clocksource be installed before we call tick_periodic() in a loop when
using ONESHOT mode. The result is we will only increment jiffies once
per interrupt until a continuous hardware clocksource is available.
Without this, we can run into a endless loop, where each cycle through
the loop, jiffies is updated which increments time by tick_period or
more (due to clock steering), which can cause the event programming to
think the next event was before the newly incremented time and fail
causing tick_periodic() to be called again and the whole process loops
forever.
[ Impact: prevent hard lock up ]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
move_irq_desc() will try to move irq_desc to the home node if
the allocated one is not correct, in create_irq_nr().
( This can happen on devices that are on different nodes that
are using MSI, when drivers are loaded and unloaded randomly. )
v2: fix non-smp build
v3: add NUMA_IRQ_DESC to eliminate #ifdefs
[ Impact: improve irq descriptor locality on NUMA systems ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F95EAE.2050903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 044d408409.
The commit added a warning when handle_IRQ_event() is called outside
of hard interrupt context. This breaks the generic tasklet based
interrupt resend mechanism which is used when the hardware has no way
to retrigger the interrupt. So we get a warning for a use case which
is correct and worked for years. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When two (or more) contexts output to the same buffer, it is possible
to observe half written output.
Suppose we have CPU0 doing perf_counter_mmap(), CPU1 doing
perf_counter_overflow(). If CPU1 does a wakeup and exposes head to
user-space, then CPU2 can observe the data CPU0 is still writing.
[ Impact: fix occasionally corrupted profiling records ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090501102533.007821627@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I was never able to understand what should we actually do when
security_task_wait() fails, but the current code doesn't look right.
If ->task_wait() returns the error, we update *notask_error correctly.
But then we either reap the child (despite the fact this was forbidden)
or clear *notask_error (and hide the securiy policy problems).
This patch assumes that "stolen by ptrace" doesn't matter. If selinux
denies the child we should ignore it but make sure we report -EACCESS
instead of -ECHLD if there are no other eligible children.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
This is necessary to avoid the conflict of syscall numbers.
Conflicts:
arch/x86/ia32/ia32entry.S
arch/x86/include/asm/unistd_32.h
arch/x86/include/asm/unistd_64.h
Fixes up the borked syscall numbers of perfcounters versus
preadv/pwritev as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
sys_kill has the per thread counterpart sys_tgkill. sigqueueinfo is
missing a thread directed counterpart. Such an interface is important
for migrating applications from other OSes which have the per thread
delivery implemented.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Split out the code from do_tkill to make it reusable by the follow up
patch which implements sys_rt_tgsigqueueinfo
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
The new requeue PI futex op codes were modeled after the existing
FUTEX_REQUEUE and FUTEX_CMP_REQUEUE calls. I was unaware at the time
that FUTEX_REQUEUE was only around for compatibility reasons and
shouldn't be used in new code. Ulrich Drepper elaborates on this in his
Futexes are Tricky paper: http://people.redhat.com/drepper/futex.pdf.
The deprecated call doesn't catch changes to the futex corresponding to
the destination futex which can lead to deadlock.
Therefor, I feel it best to remove FUTEX_REQUEUE_PI and leave only
FUTEX_CMP_REQUEUE_PI as there are not yet any existing users of the API.
This patch does change the OP code value of FUTEX_CMP_REQUEUE_PI to 12
from 13. Since my test case is the only known user of this API, I felt
this was the right thing to do, rather than leave a hole in the
enumeration.
I chose to continue using the _CMP_ modifier in the OP code to make it
explicit to the user that the test is being done.
Builds, boots, and ran several hundred iterations requeue_pi.c.
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
LKML-Reference: <49ED580E.1050502@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
include/linux/mutex.h:136: warning: 'mutex_lock' declared inline after being called
include/linux/mutex.h:136: warning: previous declaration of 'mutex_lock' was here
uninline it.
[ Impact: clean up and uninline, address compiler warning ]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Eric Paris <eparis@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <200904292318.n3TNIsi6028340@imap1.linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This adds my name to the list of copyright holders on the core
perf_counter.c, since I have contributed a significant amount of the
code in there.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
LKML-Reference: <18936.59200.888049.746658@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Sparse reports the following in kernel/posix-cpu-timers.c:
warning: symbol 'firing' shadows an earlier one
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Subrata Modak <subrata@linux.vnet.ibm.com>
LKML-Reference: <BD79186B4FD85F4B8E60E381CAEE1909016C1AFE@mi8nycmail19.Mi8.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Don't flush inherited SIGKILL during execve() in SELinux's post cred commit
hook. This isn't really a security problem: if the SIGKILL came before the
credentials were changed, then we were right to receive it at the time, and
should honour it; if it came after the creds were changed, then we definitely
should honour it; and in any case, all that will happen is that the process
will be scrapped before it ever returns to userspace.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Two minor updates on functions documentation:
- Updated documentation for function rt_mutex_unlock(), which contained an
incorrect name
- Removed extra '*' from comment in function rt_mutex_destroy()
[ Impact: cleanup ]
Signed-off-by: Luis Henriques <henrix@sapo.pt>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <20090429205451.GA23154@hades.domain.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andrew Gallatin reported that IRQ and SOFTIRQ times were
sometime not reported correctly on recent kernels, and even
bisected to commit 457533a7d3
([PATCH] fix scaled & unscaled cputime accounting) as the first
bad commit.
Further analysis pointed that commit
79741dd357 ([PATCH] idle cputime
accounting) was the real cause of the problem.
account_process_tick() was not taking into account timer IRQ
interrupting the idle task servicing a hard or soft irq.
On mostly idle cpu, irqs were thus not accounted and top or
mpstat could tell user/admin that cpu was 100 % idle, 0.00 %
irq, 0.00 % softirq, while it was not.
[ Impact: fix occasionally incorrect CPU statistics in top/mpstat ]
Reported-by: Andrew Gallatin <gallatin@myri.com>
Re-reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: rick.jones2@hp.com
Cc: brice@myri.com
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <49F84BC1.7080602@cosmosbay.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch renames struct hw_perf_counter_ops into struct pmu. It
introduces a structure to describe a cpu specific pmu (performance
monitoring unit). It may contain ops and data. The new name of the
structure fits better, is shorter, and thus better to handle. Where it
was appropriate, names of function and variable have been changed too.
[ Impact: cleanup ]
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1241002046-8832-7-git-send-email-robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a section to the memory barriers document to note the implied
memory barriers of sleep primitives (set_current_state() and wrappers)
and wake-up primitives (wake_up() and co.).
Also extend the in-code comments on the wake_up() functions to note
these implied barriers.
[ Impact: add documentation ]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <20090428140138.1192.94723.stgit@warthog.procyon.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"tracing: create automated trace defines" causes this compile error on s390,
as reported by Sachin Sant against linux-next:
kernel/built-in.o: In function `__do_softirq':
(.text+0x1c680): undefined reference to `__tracepoint_softirq_entry'
This happens because the definitions of the softirq tracepoints were moved
from kernel/softirq.c to kernel/irq/handle.c. Since s390 doesn't support
generic hardirqs handle.c doesn't get compiled and the definitions are
missing.
So move the tracepoints to softirq.c again.
[ Impact: fix build failure on s390 ]
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: fweisbec@gmail.com
LKML-Reference: <20090429135139.5fac79b8@osiris.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Replace the current event parser hack with a better one. Filters are
no longer specified predicate by predicate, but all at once and can
use parens and any of the following operators:
numeric fields:
==, !=, <, <=, >, >=
string fields:
==, !=
predicates can be combined with the logical operators:
&&, ||
examples:
"common_preempt_count > 4" > filter
"((sig >= 10 && sig < 15) || sig == 17) && comm != bash" > filter
If there was an error, the erroneous string along with an error
message can be seen by looking at the filter e.g.:
((sig >= 10 && sig < 15) || dsig == 17) && comm != bash
^
parse_error: Field not found
Currently the caret for an error always appears at the beginning of
the filter; a real position should be used, but the error message
should be useful even without it.
To clear a filter, '0' can be written to the filter file.
Filters can also be set or cleared for a complete subsystem by writing
the same filter as would be written to an individual event to the
filter file at the root of the subsytem. Note however, that if any
event in the subsystem lacks a field specified in the filter being
set, the set will fail and all filters in the subsytem are
automatically cleared. This change from the previous version was made
because using only the fields that happen to exist for a given event
would most likely result in a meaningless filter.
Because the logical operators are now implemented as predicates, the
maximum number of predicates in a filter was increased from 8 to 16.
[ Impact: add new, extended trace-filter implementation ]
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: fweisbec@gmail.com
Cc: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <1240905899.6416.121.camel@tropicana>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The new filter comparison ops need to be able to distinguish between
signed and unsigned field types, so add an is_signed flag/param to the
event field struct/trace_define_fields(). Also define a simple macro,
is_signed_type() to determine the signedness at compile time, used in the
trace macros. If the is_signed_type() macro won't work with a specific
type, a new slightly modified version of TRACE_FIELD() called
TRACE_FIELD_SIGN(), allows the signedness to be set explicitly.
[ Impact: extend trace-filter code for new feature ]
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: fweisbec@gmail.com
Cc: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <1240905893.6416.120.camel@tropicana>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Create a new event_filter object, and move the pred-related members
out of the call and subsystem objects and into the filter object - the
details of the filter implementation don't need to be exposed in the
call and subsystem in any case, and it will also help make the new
parser implementation a little cleaner.
[ Impact: refactor trace-filter code to prepare for new features ]
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: fweisbec@gmail.com
Cc: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <1240905887.6416.119.camel@tropicana>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The pages allocated for the splice binary buffer did not initialize
the ref count correctly. This caused pages not to be freed and causes
a drastic memory leak.
Thanks to logdev I was able to trace the tracer to find where the leak
was.
[ Impact: stop memory leak when using splice ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The warning output in trace_recursive_lock uses %d for a long when
it should be %ld.
[ Impact: fix compile warning ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Splice works with pages, it is much more effecient to use an entire
page than to copy bits over several pages.
Using logdev to trace the internals of the splice mechanism, I was
able to see that splice can be very aggressive. When tracing is
occurring, and the reader caught up to the writer, and the writer
is on the reader page, the reader will copy what is there into the
splice page. Splice may iterate over several pages and if the
writer is still writing to the page, the reader will keep copying
bits to new pages to pass to userspace.
This patch changes it to only pass data to userspace if the page
is full (the writer has left the page). This has a small side effect
that splice can not read a partial page, and must wait for the
page to fill. This should not be an issue. If tracing has stopped,
then a use of "read" will still read all of the page.
[ Impact: better performance for ring buffer splice code ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The splice code allocates a page even when the ring buffer is empty.
It detects the ring buffer being empty when it it fails to copy
anything from the ring buffer into the page.
This patch adds a check to see if there is anything in the ring buffer
before allocating a page.
Thanks to logdev for letting me trace the tracer to find this.
[ Impact: speed up due to removing unnecessary allocation ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The pages allocated for the splice binary buffer did not initialize
the ref count correctly. This caused pages not to be freed and causes
a drastic memory leak.
Thanks to logdev I was able to trace the tracer to find where the leak
was.
[ Impact: stop memory leak when using splice ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
ftrace_dump is used for printing out the contents of the ftrace ring buffer
to the console on failure. Currently it uses a spinlock to synchronize
the output from multiple failures on different CPUs. This spin lock
currently is a normal spinlock and can cause issues with lockdep and
lock tracing.
This patch converts it to raw since it is for error handling only.
The lock is local to the ftrace_dump and is not used by any other
infrastructure.
[ Impact: prevent ftrace_dump from locking up by internal tracing ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This simplifies the node awareness of the code. All our allocators
only deal with a NUMA node ID locality not with CPU ids anyway - so
there's no need to maintain (and transform) a CPU id all across the
IRq layer.
v2: keep move_irq_desc related
[ Impact: cleanup, prepare IRQ code to be NUMA-aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
LKML-Reference: <49F65536.2020300@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
irq_set_affinity() and move_masked_irq() try to assign affinity
before calling chip set_affinity(). Some archs are assigning it
in ->set_affinity() again.
We do something like:
cpumask_cpy(desc->affinity, mask);
desc->chip->set_affinity(mask);
But in the failure path, affinity should not be touched - otherwise
we'll end up with a different affinity mask despite the failure to
migrate the IRQ.
So try to update the afffinity only if set_affinity returns with 0.
Also call irq_set_thread_affinity accordingly.
v2: update after "irq, x86: Remove IRQ_DISABLED check in process context IRQ move"
v3: according to Ingo, change set_affinity() in irq_chip should return int.
v4: update comments by removing moving irq_desc code.
[ Impact: fix /proc/irq/*/smp_affinity setting corner case bug ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F65509.60307@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The original feature of migrating irq_desc dynamic was too fragile
and was causing problems: it caused crashes on systems with lots of
cards with MSI-X when user-space irq-balancer was enabled.
We now have new patches that create irq_desc according to device
numa node. This patch removes the leftover bits of the dynamic balancer.
[ Impact: remove dead code ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F654AF.8000808@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CPUMASKS_OFFSTACK is not defined anywhere (it is CPUMASK_OFFSTACK).
It is a typo and init_allocate_desc_masks() is called before it set
affinity to all cpus...
Split init_alloc_desc_masks() into all_desc_masks() and init_desc_masks().
Also use CPUMASK_OFFSTACK in alloc_desc_masks().
[ Impact: fix smp_affinity copying/setup when moving irq_desc between CPUs ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <49F6546E.3040406@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/irq: mark NUMA_MIGRATE_IRQ_DESC broken
x86, irq: Remove IRQ_DISABLED check in process context IRQ move
For proper module reference counting, the file_operations that modules use
must have the "owner" field set to the module. Unfortunately, the trace events
use share file_operations. The same file_operations are used by all both
kernel core and all modules.
This patch makes the modules allocate their own file_operations and
copies the functions from the core kernel. This allows those file
operations to be owned by the module.
Care is taken to free this code on module unload.
Thanks to Greg KH for reminding me that file_operations must be owned
by the module to have reference counting take place.
[ Impact: fix modular tracepoints / potential crash ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
With modules being able to add trace events, and the max trace event
counter is 16 bits (65536) we can overflow the counter easily
with a simple while loop adding and removing modules that contain
trace events.
This patch links together the registered trace events and on overflow
searches for available trace event ids. It will still fail if
over 65536 events are registered, but considering that a typical
kernel only has 22000 functions, 65000 events should be sufficient.
Reported-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Commit c751085943 ("PM/Hibernate: Wait for
SCSI devices scan to complete during resume") added a call to
scsi_complete_async_scans() to software_resume(), so that it waited for
the SCSI scanning to complete, but the call was added at a wrong place.
Namely, it should have been added after wait_for_device_probe(), which
is called only if the image partition hasn't been specified yet. Also,
it's reasonable to check if the image partition is present and only wait
for the device probing and SCSI scanning to complete if it is not the
case.
Additionally, since noresume is checked right at the beginning of
software_resume() and the function returns immediately if it's set, it
doesn't make sense to check it once again later.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slow-work appears to delete its timer as soon as the first user
unregisters, even though other users could be active. At the same time, it
never seems to delete slow_work_oom_timer. Arrange for both to happen in
the shutdown path.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
arch/x86/kernel/ptrace.c
Merge reason: fix the conflict above, and also pick up the CONFIG_BROKEN
dependency change from upstream so that we can remove it
here.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
RB_MAX_SMALL_DATA = 28bytes is too small for most tracers, it wastes
an 'u32' to save the actually length for events which data size > 28.
This fix uses compressed event header and enlarges RB_MAX_SMALL_DATA.
[ Impact: saves about 0%-12.5%(depends on tracer) memory in ring_buffer ]
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
LKML-Reference: <49F13189.3090000@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The events exported by TRACE_EVENT are automated and are guaranteed
to be correct when used.
The internal ftrace structures on the other hand are more manually
exported. These require the ftrace maintainer to make sure they
are up to date.
This patch adds a size check to help flag when a type changes in
an internal ftrace data structure, and the update needs to be reflected
in the export.
If a export is incorrect, then the only harm is that the user space
tools will not know how to correctly read the internal structures of
ftrace.
[ Impact: help prevent inconsistent ftrace format print outs ]
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
With the new event tracing registration, we must increase the number
of events that can be registered. Currently the type field is only
one byte, which leaves us only 256 possible events.
Since we do not save the CPU number in the tracer anymore (it is determined
by the per cpu ring buffer that is used) we have an extra byte to use.
This patch increases the size of type from 1 byte (256 events) to
2 bytes (65,536 events).
It also adds a WARN_ON_ONCE if we exceed that limit.
[ Impact: allow more than 255 events ]
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
The code had the following outside the lock:
if (next != wakeup_task)
return;
pc = preempt_count();
/* The task we are waiting for is waking up */
data = wakeup_trace->data[wakeup_cpu];
On initialization, wakeup_task is NULL and wakeup_cpu -1. This code
is not under a lock. If wakeup_task is set on another CPU as that
task is waking up, we can see the wakeup_task before wakeup_cpu is
set. If we read wakeup_cpu while it is still -1 then we will have
a bad data pointer.
This patch moves the reading of wakeup_cpu within the protection of
the spinlock used to protect the writing of wakeup_cpu and wakeup_task.
[ Impact: remove possible race causing invalid pointer dereference ]
Reported-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Andi Kleen reported this message triggering on non-lockdep kernels:
Disabling lockdep due to kernel taint
Clarify the message to say 'lock debugging' - debug_locks_off()
turns off all things lock debugging, not just lockdep.
[ Impact: change kernel warning message text ]
Reported-by: Andi Kleen <andi@firstfloor.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
struct trace_entry->type is unsigned char, while trace event's id is
int type, thus for a event with id >= 256, it's entry->type is cast
to (id % 256), and then we can't see the trace output of this event.
# insmod trace-events-sample.ko
# echo foo_bar > /mnt/tracing/set_event
# cat /debug/tracing/events/trace-events-sample/foo_bar/id
256
# cat /mnt/tracing/trace_pipe
<...>-3548 [001] 215.091142: Unknown type 0
<...>-3548 [001] 216.089207: Unknown type 0
<...>-3548 [001] 217.087271: Unknown type 0
<...>-3548 [001] 218.085332: Unknown type 0
[ Impact: fix output for trace events with id >= 256 ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <49EEDB0E.5070207@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add enable() and disable() callbacks for clocksources.
This allows us to put unused clocksources in power save mode. The
functions clocksource_enable() and clocksource_disable() wrap the
callbacks and are inserted in the timekeeping code to enable before use
and disable after switching to a new clocksource.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On boot up, to save memory, ftrace allocates the minimum buffer
which is two pages. Ftrace also goes through a series of tests
(when configured) on boot up. These tests can fill up a page within
a single interrupt.
The ring buffer also has a WARN_ON when it detects that the buffer was
completely filled within a single commit (other commits are allowed to
be nested).
Combine the small buffer on start up, with the tests that can fill more
than a single page within an interrupt, this can trigger the WARN_ON.
This patch makes the WARN_ON only happen when the ring buffer consists
of more than two pages.
[ Impact: prevent false WARN_ON in ftrace startup tests ]
Reported-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <20090421094616.GA14561@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Suppose we would like to trace all tasks named '123', but this
will fail:
# echo 'parent_comm == 123' > events/sched/sched_process_fork/filter
bash: echo: write error: Invalid argument
Don't guess the type of the filter pred in filter_parse(), but instead
we check it in __filter_add_pred().
[ Impact: extend allowed filter field string values ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <49ED8DEB.6000700@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If writing subsys->filter returns EINVAL or ENOSPC, the original
filters in subsys/ and subsys/events/ will be removed. This is
definitely wrong.
[ Impact: fix filter setting semantics on error condition ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <49ED8DD2.2070700@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Stephen Rothwell reported this build warning:
> kernel/sched.c: In function 'find_new_ilb':
> kernel/sched.c:4355: warning: passing argument 1 of '__first_cpu' from incompatible pointer type
>
> Possibly caused by commit f711f6090a
> ("sched: Nominate idle load balancer from a semi-idle package") from
> the sched tree. Should this call to first_cpu be cpumask_first?
For !(CONFIG_SCHED_MC || CONFIG_SCHED_SMT), find_new_ilb() nominates the
Idle load balancer as the first cpu from the nohz.cpu_mask.
This code uses the older API first_cpu(). Replace it with cpumask_first(),
which is the correct API here.
[ Impact: cleanup, address build warning ]
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <20090421031049.GA4140@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The startup tests for the event tracer also runs with the function
tracer enabled. The "wakeup" version of the trace commit was used
which can grab spinlocks. If a task was preempted by an NMI
that called a function being traced, it could deadlock due to the
function tracer trying to grab the same lock.
Thanks to Frederic Weisbecker for pointing out where the bug was.
Reported-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Althought using the irq level (hardirq_count, softirq_count and in_nmi)
was nice to detect bad recursion right away, but since the counters are
not atomically updated with respect to the interrupts, the function tracer
might trigger the test from an interrupt handler before the hardirq_count
is updated. This will trigger a false warning.
This patch converts the recursive detection to a simple counter.
If the depth is greater than 16 then the recursive detection will trigger.
16 is more than enough for any nested interrupts.
[ Impact: fix false positive trace recursion detection ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Lai Jiangshan's patch reminded me that I promised Nick to remove
that extra call overhead in schedule().
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090313112300.927414207@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This function was left orphan by the latest round of sw-counter
cleanups.
[ Impact: remove unused kernel function ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The ring_buffer_event_discard is not tied to ring_buffer_lock_reserve.
It can be called inside or outside the reserve/commit. Even if it
is called inside the reserve/commit the commit part must also be called.
Only ring_buffer_discard_commit can be used as a replacement for
ring_buffer_unlock_commit.
This patch removes the trace_recursive_unlock from ring_buffer_event_discard
since it would be the wrong place to do so.
[Impact: prevent breakage in trace recursive testing ]
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The recursive tests to detect same level recursion in the ring buffers
did not account for the hard/softirq_counts to be shifted. Thus the
numbers could be larger than then mask to be tested.
This patch includes the shift for the calculation of the irq depth.
[ Impact: stop false positives in trace recursion detection ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The late_initcall calls a helper function instead of the proper
init event selftest function.
This update may have been lost due to conflicting merges.
[ Impact: fix compiler warning and call extended event trace self tests ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently we have two configs: EVENT_TRACING and EVENT_TRACER.
All tracers enable EVENT_TRACING. The EVENT_TRACER is only a
convenience to enable the EVENT_TRACING when no other tracers
are enabled.
The names EVENT_TRACER and EVENT_TRACING are too similar and confusing.
This patch renames EVENT_TRACER to ENABLE_EVENT_TRACING to be more
appropriate to what it actually does, as well as add a comment in
the help menu to explain the option's purpose.
[ Impact: rename config option to reduce confusion ]
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
During testing we often use randconfig to test various kernels.
The current configuration set up does not give an easy way to disable
all tracing with a single config. The case where randconfig would
test all tracing disabled is very unlikely.
This patch adds a config option to enable or disable all tracing.
It is hooked into the tracing menu just like other submenus are done.
[ Impact: allow randconfig to easily produce all traces disabled ]
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch makes the branch profiling into a choice selection:
None - no branch profiling
likely/unlikely - only profile likely/unlikely branches
all - profile all branches
The all profiler will also enable the likely/unlikely branches.
This does not change the way the profiler works or the dependencies
between the profilers.
What this patch does, is keep the branch profiling from being selected
by an allyesconfig make. The branch profiler is very intrusive and
it is known to break various architecture builds when selected as an
allyesconfig.
[ Impact: prevent branch profiler from being selected in allyesconfig ]
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In case of tracing recursion detection, we only get the stacktrace.
But the current context may be very useful to debug the issue.
This patch adds the softirq/hardirq/nmi context with the warning
using lockdep context display to have a familiar output.
v2: Use printk_once()
v3: drop {hardirq,softirq}_context which depend on lockdep,
only keep what is part of current->trace_recursion,
sufficient to debug the warning source.
[ Impact: print context necessary to debug recursion ]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Commit 900af0d973 (PM: Change suspend
code ordering) changed the ordering of suspend code in such a way
that the platform .prepare() callback is now executed after the
device drivers' late suspend callbacks have run. Unfortunately, this
turns out to break ARM platforms that need to talk via I2C to power
control devices during the .prepare() callback.
For this reason introduce two new platform suspend callbacks,
.prepare_late() and .wake(), that will be called just prior to
disabling non-boot CPUs and right after bringing them back on line,
respectively, and use them instead of .prepare() and .finish() for
ACPI suspend. Make the PM core execute the .prepare() and .finish()
platform suspend callbacks where they were executed previously (that
is, right after calling the regular suspend methods provided by
device drivers and right before executing their regular resume
methods, respectively).
It is not necessary to make analogous changes to the hibernation
code and data structures at the moment, because they are only used
by ACPI platforms.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Len Brown <len.brown@intel.com>
This function is not actually used right now, since the original use
case for it was done with insert_resource_expand_to_fit() instead.
However, we now have another usage case that wants to basically do a
"reserve IO resource, splitting around existing resources", however that
one doesn't actually want the "recurse into the conflicting resource"
logic at all.
And since recursing into the conflicting resource was the most complex
part, and isn't wanted, just remove it. Maybe we'll some day want both
versions, but we can just resurrect the logic then.
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
trace_printk can be called from any context, including NMIs.
If this happens, then we must test for for recursion before
grabbing any spinlocks.
This patch prevents trace_printk from being called recursively.
[ Impact: prevent hard lockup in lockdep event tracer ]
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The tracing infrastructure allows for recursion. That is, an interrupt
may interrupt the act of tracing an event, and that interrupt may very well
perform its own trace. This is a recursive trace, and is fine to do.
The problem arises when there is a bug, and the utility doing the trace
calls something that recurses back into the tracer. This recursion is not
caused by an external event like an interrupt, but by code that is not
expected to recurse. The result could be a lockup.
This patch adds a bitmask to the task structure that keeps track
of the trace recursion. To find the interrupt depth, the following
algorithm is used:
level = hardirq_count() + softirq_count() + in_nmi;
Here, level will be the depth of interrutps and softirqs, and even handles
the nmi. Then the corresponding bit is set in the recursion bitmask.
If the bit was already set, we know we had a recursion at the same level
and we warn about it and fail the writing to the buffer.
After the data has been committed to the buffer, we clear the bit.
No atomics are needed. The only races are with interrupts and they reset
the bitmask before returning anywy.
[ Impact: detect same irq level trace recursion ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Not all the necessary symbols were exported to allow for tracing
by modules. This patch adds them in.
[ Impact: allow modules to commit data to the ring buffer ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch adds a filter_mutex to prevent the filter predicates from
being accessed concurrently by various external functions.
It's based on a previous patch by Li Zefan:
"[PATCH 7/7] tracing/filters: make filter preds RCU safe"
v2 changes:
- fixed wrong value returned in a add_subsystem_pred() failure case
noticed by Li Zefan.
[ Impact: fix trace filter corruption/crashes on parallel access ]
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Tested-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: paulmck@linux.vnet.ibm.com
LKML-Reference: <1239946028.6639.13.camel@tropicana>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Steven Rostedt reported:
> OK, I think I figured this bug out. This is a lockdep issue with respect
> to tracepoints.
>
> The trace points in lockdep are called all the time. Outside the lockdep
> logic. But if lockdep were to trigger an error / warning (which this run
> did) we might be in trouble. For new locks, like the dentry->d_lock, that
> are created, they will not get a name:
>
> void lockdep_init_map(struct lockdep_map *lock, const char *name,
> struct lock_class_key *key, int subclass)
> {
> if (unlikely(!debug_locks))
> return;
>
> When a problem is found by lockdep, debug_locks becomes false. Thus we
> stop allocating names for locks. This dentry->d_lock I had, now has no
> name. Worse yet, I have CONFIG_DEBUG_VM set, that scrambles non
> initialized memory. Thus, when the trace point was hit, it had junk for
> the lock->name, and the machine crashed.
Ah, nice catch. I think we should put at least the name in regardless.
Ensure we at least initialize the trivial entries of the depmap so that
they can be relied upon, even when lockdep itself decided to pack up and
go home.
[ Impact: fix lock tracing after lockdep warnings. ]
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1239954049.23397.4156.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We can find some bugs in the trace events if we stress the writes as well.
The function tracer is a good way to stress the events.
[ Impact: extend scope of event tracer self-tests ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090416161746.604786131@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Export the cached task comms to userspace. This allows user apps to translate
the pids from a trace into their respective task command lines.
[ Impact: let userspace apps reading binary buffer know comm's of pids ]
Signed-off-by: Avadh Patel <avadh4all@gmail.com>
[ added error checking and use of buf pointer to index file_buf ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently, every thing needed to read the binary output from the
ring buffers is available, with the exception of the way the ring
buffers handles itself internally.
This patch creates two special files in the debugfs/tracing/events
directory:
# cat /debug/tracing/events/header_page
field: u64 timestamp; offset:0; size:8;
field: local_t commit; offset:8; size:8;
field: char data; offset:16; size:4080;
# cat /debug/tracing/events/header_event
type : 2 bits
len : 3 bits
time_delta : 27 bits
array : 32 bits
padding : type == 0
time_extend : type == 1
data : type == 3
This is to allow a userspace app to see if the ring buffer format changes
or not.
[ Impact: allow userspace apps to know of ringbuffer format changes ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As events start to become popular, and the new way to add tracing
infrastructure into ftrace, it is important to catch any problems
that might happen with a mistake in the TRACE_EVENT macro.
This patch introduces a startup self test on the registered trace
events. Note, it can only do a generic test, any type of testing that
needs more involement is needed to be implemented by the tracepoint
creators.
The test goes down one by one enabling a trace point and running
some random tasks (random in the sense that I just made them up).
Those tasks are creating threads, grabbing mutexes and spinlocks
and using workqueues.
After testing each event individually, it does the same test after
enabling each system of trace points. Like sched, irq, lockdep.
Then finally it enables all tracepoints and performs the tasks again.
The output to the console on bootup will look like this when everything
works:
Running tests on trace events:
Testing event kfree_skb: OK
Testing event kmalloc: OK
Testing event kmem_cache_alloc: OK
Testing event kmalloc_node: OK
Testing event kmem_cache_alloc_node: OK
Testing event kfree: OK
Testing event kmem_cache_free: OK
Testing event irq_handler_exit: OK
Testing event irq_handler_entry: OK
Testing event softirq_entry: OK
Testing event softirq_exit: OK
Testing event lock_acquire: OK
Testing event lock_release: OK
Testing event sched_kthread_stop: OK
Testing event sched_kthread_stop_ret: OK
Testing event sched_wait_task: OK
Testing event sched_wakeup: OK
Testing event sched_wakeup_new: OK
Testing event sched_switch: OK
Testing event sched_migrate_task: OK
Testing event sched_process_free: OK
Testing event sched_process_exit: OK
Testing event sched_process_wait: OK
Testing event sched_process_fork: OK
Testing event sched_signal_send: OK
Running tests on trace event systems:
Testing event system skb: OK
Testing event system kmem: OK
Testing event system irq: OK
Testing event system lockdep: OK
Testing event system sched: OK
Running tests on all trace events:
Testing all events: OK
[ folded in:
tracing: add #include <linux/delay.h> to fix build failure in test_work()
This build failure occured on a few rare configs:
kernel/trace/trace_events.c: In function ‘test_work’:
kernel/trace/trace_events.c:975: error: implicit declaration of function ‘udelay’
kernel/trace/trace_events.c:980: error: implicit declaration of function ‘msleep’
delay.h is included in way too many other headers, hiding cases
where new usage is added without header inclusion.
[ Impact: build fix ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
]
[ Impact: add event tracer self-tests ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The hooks in the module code for the function tracer must be called
before any of that module code runs. The function tracer hooks
modify the module (replacing calls to mcount to nops). If the code
is executed while the change occurs, then the CPU can take a GPF.
To handle the above with a bit of paranoia, I originally implemented
the hooks as calls directly from the module code.
After examining the notifier calls, it looks as though the start up
notify is called before any of the module's code is executed. This makes
the use of the notify safe with ftrace.
Only the startup notify is required to be "safe". The shutdown simply
removes the entries from the ftrace function list, and does not modify
any code.
This change has another benefit. It removes a issue with a reverse dependency
in the mutexes of ftrace_lock and module_mutex.
[ Impact: fix lock dependency bug, cleanup ]
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Avoid printing sched_group::__cpu_power for default case
tracing, sched: mark get_parent_ip() notrace
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
kernel/softirq.c: fix sparse warning
rcu: Make hierarchical RCU less IPI-happy
Fix sparse warning in kernel/softirq.c.
warning: do-while statement is not a compound statement
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
LKML-Reference: <BD79186B4FD85F4B8E60E381CAEE1909015F9033@mi8nycmail19.Mi8.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 46e0bb9c12 ("sched: Print sched_group::__cpu_power
in sched_domain_debug") produces a messy dmesg output while
attempting to print the sched_group::__cpu_power for each
group in the sched_domain hierarchy.
Fix this by avoid printing the __cpu_power for default cases.
(i.e, __cpu_power == SCHED_LOAD_SCALE).
[ Impact: reduce syslog clutter ]
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Fixed-by: Tony Luck <tony.luck@intel.com>
Cc: a.p.zijlstra@chello.nl
LKML-Reference: <20090414033936.GA534@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When current tracer is set to blk tracer, TRACE_ITER_CONTEXT_INFO is
unset, but actually context-info is printed:
pdflush-431 [000] 821.181576: 8,0 P N [pdflush]
And then if we enable TRACE_ITER_CONTEXT_INFO:
# echo context-info > trace_options
We'll see context-info printed twice. What's worse, when we use blk
tracer and trace events at the same time, we'll see no context-info
for trace events at all:
jbd2_commit_logging: dev dm-0:8 transaction 333227
jbd2_end_commit: dev dm-0:8 transaction 333227 head 332814
rm-25433 [001] 9578.307485: 8,18 m N cfq25433 slice expired t=0
rm-25433 [001] 9578.307486: 8,18 m N cfq25433 put_queue
This patch adds blk_tracer->set_flags(), and context-info flag is unset
only when we set the output to classic mode.
Note after this patch, one should unset context-info explicitly if he
wants to get binary output that can be parsed by blkparse:
# echo nocontext-info > trace_options
# echo bin > trace_options
# echo blk > current_tracer
# cat trace_pipe | blkparse -i -
Reported-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <49E54E60.50408@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The previous patch adds support to trace a single partition for
relay+ioctl blktrace, and this patch is for ftrace plugin blktrace:
# echo 1 > /sys/block/sda/sda7/enable
# cat start_lba
102398373
# cat end_lba
102703545
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Shawn Du <duyuyang@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
LKML-Reference: <49E42646.4060608@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Though one can specify '-d /dev/sda1' when using blktrace, it still
traces the whole sda.
To support per-partition tracing, when we start tracing, we initialize
bt->start_lba and bt->end_lba to the start and end sector of that
partition.
Note some actions are per device, thus we don't filter 0-sector events.
The original patch and discussion can be found here:
http://marc.info/?l=linux-btrace&m=122949374214540&w=2
Signed-off-by: Shawn Du <duyuyang@gmail.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
LKML-Reference: <49E42620.4050701@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Don't try and predeclare inline funcs like this:
static inline void wait_migrated_callbacks(void)
...
static void _rcu_barrier(enum rcu_barrier type)
{
...
wait_migrated_callbacks();
}
...
static inline void wait_migrated_callbacks(void)
{
wait_event(rcu_migrate_wq, !atomic_read(&rcu_migrate_type_count));
}
as it upsets some versions of gcc under some circumstances:
kernel/rcupdate.c: In function `_rcu_barrier':
kernel/rcupdate.c:125: sorry, unimplemented: inlining failed in call to 'wait_migrated_callbacks': function body not available
kernel/rcupdate.c:152: sorry, unimplemented: called from here
This can be dealt with by simply putting the static variables (rcu_migrate_*)
at the top, and moving the implementation of the function up so that it
replaces its forward declaration.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: clean up
Create a sub directory in include/trace called events to keep the
trace point headers in their own separate directory. Only headers that
declare trace points should be defined in this directory.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Impact: compile fix
The addition of TRACE_EVENT for modules breaks the build for when
modules are disabled. This code fixes that.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Commit 3d43321b70 ("modules: sysctl to
block module loading") introduces a modules_disabled variable that is
only defined if CONFIG_MODULE_UNLOAD is enabled, despite being used in
other places. This moves it up and fixes up the build.
CC kernel/module.o
kernel/module.c: In function 'sys_init_module':
kernel/module.c:2401: error: 'modules_disabled' undeclared (first use in this function)
kernel/module.c:2401: error: (Each undeclared identifier is reported only once
kernel/module.c:2401: error: for each function it appears in.)
make[1]: *** [kernel/module.o] Error 1
make: *** [kernel/module.o] Error 2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: James Morris <jmorris@namei.org>
Impact: allow modules to add TRACE_EVENTS on load
This patch adds the final hooks to allow modules to use the TRACE_EVENT
macro. A notifier and a data structure are used to link the TRACE_EVENTs
defined in the module to connect them with the ftrace event tracing system.
It also adds the necessary automated clean ups to the trace events when a
module is removed.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Impact: let modules add trace events
The trace event code requires some functions to be exported to allow
modules to use TRACE_EVENT. This patch adds EXPORT_SYMBOL_GPL to the
necessary functions.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Impact: makes it possible to define events in modules
The events are created by reading down the section that they are linked
in by the macros. But this is not scalable to modules. This patch converts
the manipulations to use a global link list, and on boot up it adds
the items in the section to the list.
This change will allow modules to add their tracing events to the list as
well.
Note, this change alone does not permit modules to use the TRACE_EVENT macros,
but the change is needed for them to eventually do so.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch moves the ftrace creation into include/trace/ftrace.h and
simplifies the work of developers in adding new tracepoints.
Just the act of creating the trace points in include/trace and including
define_trace.h will create the events in the debugfs/tracing/events
directory.
This patch removes the need of include/trace/trace_events.h
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In preparation to allowing trace events to happen in modules, we need
to move some of the local declarations in the kernel/trace directory
into include/linux.
This patch simply moves the declarations and performs no context changes.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In the process to make TRACE_EVENT macro work for modules, the trace_seq
operations must be available for core kernel code.
These operations are quite useful and can be used for other implementations.
The main idea is that we create a trace_seq handle that acts very much
like the seq_file handle.
struct trace_seq *s = kmalloc(sizeof(*s, GFP_KERNEL);
trace_seq_init(s);
trace_seq_printf(s, "some data %d\n", variable);
printk("%s", s->buffer);
The main use is to allow a top level function call several other functions
that may store printf like data into the buffer. Then at the end, the top
level function can process all the data with any method it would like to.
It could be passed to userspace, output via printk or even use seq_file:
trace_seq_to_user(s, ubuf, cnt);
seq_puts(m, s->buffer);
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch lowers the number of places a developer must modify to add
new tracepoints. The current method to add a new tracepoint
into an existing system is to write the trace point macro in the
trace header with one of the macros TRACE_EVENT, TRACE_FORMAT or
DECLARE_TRACE, then they must add the same named item into the C file
with the macro DEFINE_TRACE(name) and then add the trace point.
This change cuts out the needing to add the DEFINE_TRACE(name).
Every file that uses the tracepoint must still include the trace/<type>.h
file, but the one C file must also add a define before the including
of that file.
#define CREATE_TRACE_POINTS
#include <trace/mytrace.h>
This will cause the trace/mytrace.h file to also produce the C code
necessary to implement the trace point.
Note, if more than one trace/<type>.h is used to create the C code
it is best to list them all together.
#define CREATE_TRACE_POINTS
#include <trace/foo.h>
#include <trace/bar.h>
#include <trace/fido.h>
Thanks to Mathieu Desnoyers and Christoph Hellwig for coming up with
the cleaner solution of the define above the includes over my first
design to have the C code include a "special" header.
This patch converts sched, irq and lockdep and skb to use this new
method.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Jeremy Fitzhardinge reported this build failure:
LD .tmp_vmlinux1
arch/x86/kernel/built-in.o: In function `ds_take_timestamp':
git/linux/arch/x86/kernel/ds.c:1380: undefined reference to `trace_clock_global'
git/linux/arch/x86/kernel/ds.c:1380: undefined reference to `trace_clock_global'
Which is due to !CONFIG_TRACING && CONFIG_X86_DS=y.
Expose the trace clock code to CONFIG_X86_DS as well.
[ Unfortunately librarizing doesnt work well - ancient architectures
with no raw_local_irq_save() primitive break the build. ]
Reported-by: Jeremy Fitzhardinge <jeremy@goop.org>
LKML-Reference: <49E4413F.7070700@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
'777c6c5 wait: prevent exclusive waiter starvation' made
__wake_up_common() global to be used from abort_exclusive_wait().
It was needed to do a wake-up with the waitqueue lock held while
passing down a key to the wake-up function.
Since '4ede816 epoll keyed wakeups: add __wake_up_locked_key() and
__wake_up_sync_key()' there is an appropriate wrapper for this case:
__wake_up_locked_key().
Use it here and make __wake_up_common() private to the scheduler
again.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1239720785-19661-1-git-send-email-hannes@cmpxchg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clean up
Neil Horman (et. al.) criticized the way the trace events were broken up
into two files. The reason for that was that ftrace needed to separate out
the declarations from where the #include <linux/tracepoint.h> was used.
It then dawned on me that the tracepoint.h header only needs to define the
TRACE_EVENT macro if it is not already defined.
The solution is simply to test if TRACE_EVENT is defined, and if it is not
then the linux/tracepoint.h header can define it. This change consolidates
all the <traces>.h and <traces>_event_types.h into the <traces>.h file.
Reported-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Theodore Tso <tytso@mit.edu>
Reported-by: Jiaying Zhang <jiayingz@google.com>
Cc: Zhaolei <zhaolei@cn.fujitsu.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As discussed in the thread here:
http://marc.info/?l=linux-kernel&m=123964468521142&w=2
Eric W. Biederman observed:
> It looks like some additional bugs have slipped in since last I looked.
>
> set_irq_affinity does this:
> ifdef CONFIG_GENERIC_PENDING_IRQ
> if (desc->status & IRQ_MOVE_PCNTXT || desc->status & IRQ_DISABLED) {
> cpumask_copy(desc->affinity, cpumask);
> desc->chip->set_affinity(irq, cpumask);
> } else {
> desc->status |= IRQ_MOVE_PENDING;
> cpumask_copy(desc->pending_mask, cpumask);
> }
> #else
>
> That IRQ_DISABLED case is a software state and as such it has nothing to
> do with how safe it is to move an irq in process context.
[...]
>
> The only reason we migrate MSIs in interrupt context today is that there
> wasn't infrastructure for support migration both in interrupt context
> and outside of it.
Yes. The idea here was to force the MSI migration to happen in process
context. One of the patches in the series did
disable_irq(dev->irq);
irq_set_affinity(dev->irq, cpumask_of(dev->cpu));
enable_irq(dev->irq);
with the above patch adding irq/manage code check for interrupt disabled
and moving the interrupt in process context.
IIRC, there was no IRQ_MOVE_PCNTXT when we were developing this HPET
code and we ended up having this ugly hack. IRQ_MOVE_PCNTXT was there
when we eventually submitted the patch upstream. But, looks like I did a
blind rebasing instead of using IRQ_MOVE_PCNTXT in hpet MSI code.
Below patch fixes this. i.e., revert commit 932775a4ab
and add PCNTXT to HPET MSI setup. Also removes copying of desc->affinity
in generic code as set_affinity routines are doing it internally.
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Li Shaohua" <shaohua.li@intel.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: "lcm@us.ibm.com" <lcm@us.ibm.com>
Cc: suresh.b.siddha@intel.com
LKML-Reference: <20090413222058.GB8211@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The CPU that first goes idle becomes the idle-load-balancer and remains
that until either it picks up a task or till all the CPUs of the system
goes idle.
Optimize this further to allow it to relinquish it's post
once all it's siblings in the power-aware sched_domain go idle, thereby
allowing the whole package-core to go idle. While relinquising the post,
nominate another an idle-load balancer from a semi-idle core/package.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090414045535.7645.31641.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the nomination of idle-load balancer is done by choosing the first
idle cpu in the nohz.cpu_mask. This may not be power-efficient, since
such an idle cpu could come from a completely idle core/package thereby
preventing the whole core/package from being in a low-power state.
For eg, consider a quad-core dual package system. The cpu numbering need
not be sequential and can something like [0, 2, 4, 6] and [1, 3, 5, 7].
With sched_mc/smt_power_savings and the power-aware IRQ balance, we try to keep
as fewer Packages/Cores active. But the current idle load balancer logic
goes against this by choosing the first_cpu in the nohz.cpu_mask and not
taking the system topology into consideration.
Improve the algorithm to nominate the idle load balancer from a semi idle
cores/packages thereby increasing the probability of the cores/packages being
in deeper sleep states for longer duration.
The algorithm is activated only when sched_mc/smt_power_savings != 0.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090414045530.7645.12175.stgit@sofia.in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes a hierarchical-RCU performance bug located by Anton
Blanchard. The problem stems from a misguided attempt to provide a
work-around for jiffies-counter failure. This work-around uses a per-CPU
n_rcu_pending counter, which is incremented on each call to rcu_pending(),
which in turn is called from each scheduling-clock interrupt. Each CPU
then treats this counter as a surrogate for the jiffies counter, so
that if the jiffies counter fails to advance, the per-CPU n_rcu_pending
counter will cause RCU to invoke force_quiescent_state(), which in turn
will (among other things) send resched IPIs to CPUs that have thus far
failed to pass through an RCU quiescent state.
Unfortunately, each CPU resets only its own counter after sending a
batch of IPIs. This means that the other CPUs will also (needlessly)
send -another- round of IPIs, for a full N-squared set of IPIs in the
worst case every three scheduler-clock ticks until the grace period
finally ends. It is not reasonable for a given CPU to reset each and
every n_rcu_pending for all the other CPUs, so this patch instead simply
disables the jiffies-counter "training wheels", thus eliminating the
excessive IPIs.
Note that the jiffies-counter IPIs do not have this problem due to
the fact that the jiffies counter is global, so that the CPU sending
the IPIs can easily reset things, thus preventing the other CPUs from
sending redundant IPIs.
Note also that the n_rcu_pending counter remains, as it will continue to
be used for tracing. It may also see use to update the jiffies counter,
should an appropriate kick-the-jiffies-counter API appear.
Located-by: Anton Blanchard <anton@au1.ibm.com>
Tested-by: Anton Blanchard <anton@au1.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: anton@samba.org
Cc: akpm@linux-foundation.org
Cc: dipankar@in.ibm.com
Cc: manfred@colorfullife.com
Cc: cl@linux-foundation.org
Cc: josht@linux.vnet.ibm.com
Cc: schamp@sgi.com
Cc: niv@us.ibm.com
Cc: dvhltc@us.ibm.com
Cc: ego@in.ibm.com
Cc: laijs@cn.fujitsu.com
Cc: rostedt@goodmis.org
Cc: peterz@infradead.org
Cc: penberg@cs.helsinki.fi
Cc: andi@firstfloor.org
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
LKML-Reference: <12396834793575-git-send-email->
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: remove overly redundant tracing entries
When tracer is "function" or "function_graph", way too much
"get_parent_ip" entries are recorded in ring_buffer.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <srostedt@redhat.com>
LKML-Reference: <49D458B1.5000703@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pointed out by Roland. The bug was recently introduced by me in
"forget_original_parent: split out the un-ptrace part", commit
39c626ae47.
Since that patch we have a window after exit_ptrace() drops tasklist and
before forget_original_parent() takes it again. In this window the child
can do ptrace(PTRACE_TRACEME) and nobody can untrace this child after
that.
Change ptrace_traceme() to not attach to the exiting ->real_parent. We
don't report the error in this case, we pretend we attach right before
->real_parent calls exit_ptrace() which should untrace us anyway.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vm knobs should go in the vm table. Probably too late for
randomize_va_space though.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch allows event filters to be safely removed or switched
on-the-fly while avoiding the use of rcu or the suspension of tracing of
previous versions.
It does it by adding a new filter_pred_none() predicate function which
does nothing and by never deallocating either the predicates or any of
the filter_pred members used in matching; the predicate lists are
allocated and initialized during ftrace_event_calls initialization.
Whenever a filter is removed or replaced, the filter_pred_* functions
currently in use by the affected ftrace_event_call are immediately
switched over to to the filter_pred_none() function, while the rest of
the filter_pred members are left intact, allowing any currently
executing filter_pred_* functions to finish up, using the values they're
currently using.
In the case of filter replacement, the new predicate values are copied
into the old predicates after the above step, and the filter_pred_none()
functions are replaced by the filter_pred_* functions for the new
filter. In this case, it is possible though very unlikely that a
previous filter_pred_* is still running even after the
filter_pred_none() switch and the switch to the new filter_pred_*. In
that case, however, because nothing has been deallocated in the
filter_pred, the worst that can happen is that the old filter_pred_*
function sees the new values and as a result produces either a false
positive or a false negative, depending on the values it finds.
So one downside to this method is that rarely, it can produce a bad
match during the filter switch, but it should be possible to live with
that, IMHO.
The other downside is that at least in this patch the predicate lists
are always pre-allocated, taking up memory from the start. They could
probably be allocated on first-use, and de-allocated when tracing is
completely stopped - if this patch makes sense, I could create another
one to do that later on.
Oh, and it also places a restriction on the size of __arrays in events,
currently set to 128, since they can't be larger than the now embedded
str_val arrays in the filter_pred struct.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: paulmck@linux.vnet.ibm.com
LKML-Reference: <1239610670.6660.49.camel@tropicana>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch changes filter_check_discard() to make use of the new
ring_buffer_discard_commit() function and modifies the current users to
call the old commit function in the non-discard case.
It also introduces a version of filter_check_discard() that uses the
global trace buffer (filter_current_check_discard()) for those cases.
v2 changes:
- fix compile error noticed by Ingo Molnar
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: fweisbec@gmail.com
LKML-Reference: <1239178554.10295.36.camel@tropicana>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a new config option, CONFIG_EVENT_TRACING that gets selected
when CONFIG_TRACING is selected and adds everything needed by the stuff
in trace_export - basically all the event tracing support needed by e.g.
bprint, minus the actual events, which are only included if
CONFIG_EVENT_TRACER is selected.
So CONFIG_EVENT_TRACER can be used to turn on or off the generated events
(what I think of as the 'event tracer'), while CONFIG_EVENT_TRACING turns
on or off the base event tracing support used by both the event tracer and
the other things such as bprint that can't be configured out.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: fweisbec@gmail.com
LKML-Reference: <1239178441.10295.34.camel@tropicana>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The ring_buffer_discard_commit makes better usage of the ring_buffer
when an event has been discarded. It tries to remove it completely if
possible.
This patch converts the trace event filtering to use
ring_buffer_discard_commit instead of the ring_buffer_event_discard.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The ring_buffer_discard_commit is similar to ring_buffer_event_discard
but it can only be done on an event that has yet to be commited.
Unpredictable results can happen otherwise.
The main difference between ring_buffer_discard_commit and
ring_buffer_event_discard is that ring_buffer_discard_commit will try
to free the data in the ring buffer if nothing has addded data
after the reserved event. If something did, then it acts almost the
same as ring_buffer_event_discard followed by a
ring_buffer_unlock_commit.
Note, either ring_buffer_commit_discard and ring_buffer_unlock_commit
can be called on an event, not both.
This commit also exports both discard functions to be usable by
GPL modules.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Frederic Weisbecker suggested that the trace_special event shouldn't be
filterable; this patch adds a TRACE_EVENT_FORMAT_NOFILTER event macro
that allows an event format to be exported without having a filter
attached, and removes filtering from the trace_special event.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds run-time field descriptions to all the event formats
exported using TRACE_EVENT_FORMAT. It also hooks up all the tracers
that use them (i.e. the tracers in the 'ftrace subsystem') so they can
also have their output filtered by the event-filtering mechanism.
When I was testing this, there were a couple of things that fooled me
into thinking the filters weren't working, when actually they were -
I'll mention them here so others don't make the same mistakes (and file
bug reports. ;-)
One is that some of the tracers trace multiple events e.g. the
sched_switch tracer uses the context_switch and wakeup events, and if
you don't set filters on all of the traced events, the unfiltered output
from the events without filters on them can make it look like the
filtering as a whole isn't working properly, when actually it is doing
what it was asked to do - it just wasn't asked to do the right thing.
The other is that for the really high-volume tracers e.g. the function
tracer, the volume of filtered events can be so high that it pushes the
unfiltered events out of the ring buffer before they can be read so e.g.
cat'ing the trace file repeatedly shows either no output, or once in
awhile some output but that isn't there the next time you read the
trace, which isn't what you normally expect when reading the trace file.
If you read from the trace_pipe file though, you can catch them before
they disappear.
Changes from v1:
As suggested by Frederic Weisbecker:
- get rid of externs in functions
- added unlikely() to filter_check_discard()
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Before patch:
# tracer: power
#
# TASK-PID CPU# TIMESTAMP FUNCTION
# | | | | |
[ 676.875865889] CSTATE: Going to C1 on cpu 0 for 0.005911463
[ 676.882938805] CSTATE: Going to C1 on cpu 0 for 0.104796532
...
After patch:
# tracer: power
#
# TIMESTAMP STATE EVENT
# | | |
[ 676.875865889] CSTATE: Going to C1 on cpu 0 for 0.005911463
[ 676.882938805] CSTATE: Going to C1 on cpu 0 for 0.104796532
...
v2: Use seq_puts instead of seq_printf
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <49E2E889.5000903@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.
In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing/filters: return proper error code when writing filter file
tracing/filters: allow user input integer to be oct or hex
tracing/filters: fix NULL pointer dereference
tracing/filters: NIL-terminate user input filter
ftrace: Output REC->var instead of __entry->var for trace format
Make __stringify support variable argument macros too
tracing: fix document references
tracing: fix splice return too large
tracing: update file->f_pos when splice(2) it
tracing: allocate page when needed
tracing: disable seeking for trace_pipe_raw
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: continue lock debugging despite some taints
lockdep: warn about lockdep disabling after kernel taint
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
percpu: unbreak alpha percpu
mutex: have non-spinning mutexes on s390 by default
Impact: broaden lockdep checks
Lockdep is disabled after any kernel taints. This might be convenient
to ignore bad locking issues which sources come from outside the kernel
tree. Nevertheless, it might be a frustrating experience for the
staging developers or those who experience a warning but are focused
on another things that require lockdep.
The v2 of this patch simply don't disable anymore lockdep in case
of TAINT_CRAP and TAINT_WARN events.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: LTP <ltp-list@lists.sourceforge.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg KH <gregkh@suse.de>
LKML-Reference: <1239412638-6739-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: provide useful missing info for developers
Kernel taint can occur in several situations such as warnings,
load of prorietary or staging modules, bad page, etc...
But when such taint happens, a developer might still be working on
the kernel, expecting that lockdep is still enabled. But a taint
disables lockdep without ever warning about it.
Such a kernel behaviour doesn't really help for kernel development.
This patch adds this missing warning.
Since the taint is done most of the time after the main message that
explain the real source issue, it seems safe to warn about it inside
add_taint() so that it appears at last, without hurting the main
information.
v2: Use a generic helper to disable lockdep instead of an
open coded xchg().
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <1239412638-6739-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
BLK_TC_PC events should be treated differently with BLK_TC_FS events.
Before this patch:
# echo 1 > /sys/block/sda/sda1/trace/enable
# echo pc > /sys/block/sda/sda1/trace/act_mask
# echo blk > /debugfs/tracing/current_tracer
# (generate some BLK_TC_PC events)
# cat trace
bash-2184 [000] 1774.275413: 8,7 I N [bash]
bash-2184 [000] 1774.275435: 8,7 D N [bash]
bash-2184 [000] 1774.275540: 8,7 I R [bash]
bash-2184 [000] 1774.275547: 8,7 D R [bash]
ksoftirqd/0-4 [000] 1774.275580: 8,7 C N 0 [0]
bash-2184 [000] 1774.275648: 8,7 I R [bash]
bash-2184 [000] 1774.275653: 8,7 D R [bash]
ksoftirqd/0-4 [000] 1774.275682: 8,7 C N 0 [0]
bash-2184 [000] 1774.275739: 8,7 I R [bash]
bash-2184 [000] 1774.275744: 8,7 D R [bash]
ksoftirqd/0-4 [000] 1774.275771: 8,7 C N 0 [0]
bash-2184 [000] 1774.275804: 8,7 I R [bash]
bash-2184 [000] 1774.275808: 8,7 D R [bash]
ksoftirqd/0-4 [000] 1774.275836: 8,7 C N 0 [0]
After this patch:
# cat trace
bash-2263 [000] 366.782149: 8,7 I N 0 (00 ..) [bash]
bash-2263 [000] 366.782323: 8,7 D N 0 (00 ..) [bash]
bash-2263 [000] 366.782557: 8,7 I R 8 (25 00 ..) [bash]
bash-2263 [000] 366.782560: 8,7 D R 8 (25 00 ..) [bash]
ksoftirqd/0-4 [000] 366.782582: 8,7 C N (25 00 ..) [0]
bash-2263 [000] 366.782648: 8,7 I R 8 (5a 00 3f 00) [bash]
bash-2263 [000] 366.782650: 8,7 D R 8 (5a 00 3f 00) [bash]
ksoftirqd/0-4 [000] 366.782669: 8,7 C N (5a 00 3f 00) [0]
bash-2263 [000] 366.782710: 8,7 I R 8 (5a 00 08 00) [bash]
bash-2263 [000] 366.782713: 8,7 D R 8 (5a 00 08 00) [bash]
ksoftirqd/0-4 [000] 366.782730: 8,7 C N (5a 00 08 00) [0]
bash-2263 [000] 366.783375: 8,7 I R 36 (5a 00 08 00) [bash]
bash-2263 [000] 366.783379: 8,7 D R 36 (5a 00 08 00) [bash]
ksoftirqd/0-4 [000] 366.783404: 8,7 C N (5a 00 08 00) [0]
This is what we do with PC events in user-space blktrace.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <49D32387.9040106@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Not all events are pc (packet command) events. An event is a pc
event only if it has BLK_TC_PC bit set.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <49D3236D.3090705@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: refactor code for future changes
Current kmemtrace.h is used both as header file of kmemtrace and kmem's
tracepoints definition.
Tracepoints' definition file may be used by other code, and should only have
definition of tracepoint.
We can separate include/trace/kmemtrace.h into 2 files:
include/linux/kmemtrace.h: header file for kmemtrace
include/trace/kmem.h: definition of kmem tracepoints
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <49DEE68A.5040902@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- propagate return value of filter_add_pred() to the user
- return -ENOSPC but not -ENOMEM or -EINVAL when the filter array
is full
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Tom Zanussi <tzanussi@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <49E04CF0.3010105@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make sure messages from user space are NIL-terminated strings,
otherwise we could dump random memory while reading filter file.
Try this:
# echo 'parent_comm ==' > events/sched/sched_process_fork/filter
# cat events/sched/sched_process_fork/filter
parent_comm == �
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Tom Zanussi <tzanussi@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <49E04C32.6060508@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Several drivers use asynchronous work to do device discovery, and we
synchronize with them in the compiled-in case before we actually try to
mount root filesystems etc.
However, when compiled as modules, that synchronization is missing - the
module loading completes, but the driver hasn't actually finished
probing for devices, and that means that any user mode that expects to
use the devices after the 'insmod' is now potentially broken.
We already saw one case of a similar issue in the ACPI battery code,
where the kernel itself expected the module to be all done, and unmapped
the init memory - but the async device discovery was still running.
That got hacked around by just removing the "__init" (see commit
5d38258ec0 "ACPI battery: fix async boot
oops"), but the real fix is to just make the module loading wait for all
async work to be completed.
It will slow down module loading, but since common devices should be
built in anyway, and since the bug is really annoying and hard to handle
from user space (and caused several S3 resume regressions), the simple
fix to wait is the right one.
This fixes at least
http://bugzilla.kernel.org/show_bug.cgi?id=13063
but probably a few other bugzilla entries too (12936, for example), and
is confirmed to fix Rafael's storage driver breakage after resume bug
report (no bugzilla entry).
We should also be able to now revert that ACPI battery fix.
Reported-and-tested-by: Rafael J. Wysocki <rjw@suse.com>
Tested-by: Heinz Diehl <htd@fancy-poultry.org>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the get_futex_key() call were to fail, the existing code would
try and put_futex_key() prior to returning. This patch makes sure
we only put_futex_key() if get_futex_key() succeeded.
Reported-by: Clark Williams <williams@redhat.com>
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
LKML-Reference: <20090410165005.14342.16973.stgit@Aeon>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When moving documents to Documentation/trace/, I forgot to
grep Kconfig to find out those references.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Pekka Paalanen <pq@iki.fi>
Cc: eduard.munteanu@linux360.ro
LKML-Reference: <49DE97EF.7080208@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While trying to optimize the new lock on reiserfs to replace
the bkl, I find the lock tracing very useful though it lacks
something important for performance (and latency) instrumentation:
the time a task waits for a lock.
That's what this patch implements:
bash-4816 [000] 202.652815: lock_contended: lock_contended: &sb->s_type->i_mutex_key
bash-4816 [000] 202.652819: lock_acquired: &rq->lock (0.000 us)
<...>-4787 [000] 202.652825: lock_acquired: &rq->lock (0.000 us)
<...>-4787 [000] 202.652829: lock_acquired: &rq->lock (0.000 us)
bash-4816 [000] 202.652833: lock_acquired: &sb->s_type->i_mutex_key (16.005 us)
As shown above, the "lock acquired" field is followed by the time
it has been waiting for the lock. Usually, a lock contended entry
is followed by a near lock_acquired entry with a non-zero time waited.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <1238975373-15739-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: pick up both v2.6.30-rc1 [which includes tracing/urgent fixes]
and pick up the current lineup of tracing/urgent fixes as well
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I got these from strace:
splice(0x3, 0, 0x5, 0, 0x1000, 0x1) = 12288
splice(0x3, 0, 0x5, 0, 0x1000, 0x1) = 12288
splice(0x3, 0, 0x5, 0, 0x1000, 0x1) = 12288
splice(0x3, 0, 0x5, 0, 0x1000, 0x1) = 16384
splice(0x3, 0, 0x5, 0, 0x1000, 0x1) = 8192
splice(0x3, 0, 0x5, 0, 0x1000, 0x1) = 8192
splice(0x3, 0, 0x5, 0, 0x1000, 0x1) = 8192
I wanted to splice_read 4096 bytes, but it returns 8192 or larger.
It is because the return value of tracing_buffers_splice_read()
does not include "zero out any left over data" bytes.
But tracing_buffers_read() includes these bytes, we make them
consistent.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
LKML-Reference: <49D46674.9030804@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Cleanup
These two lines:
if (unlikely(*ppos))
return -ESPIPE;
in tracing_buffers_splice_read() are not needed, VFS layer
has disabled seek(2).
We remove these two lines, and then we can update file->f_pos.
And tracing_buffers_read() updates file->f_pos, this fix
make tracing_buffers_splice_read() updates file->f_pos too.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
LKML-Reference: <49D46670.4010503@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Cleanup
Sometimes, we open trace_pipe_raw, but we don't read(2) it,
we just splice(2) it, thus, the page is not used.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
LKML-Reference: <49D4666B.4010608@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: disable pread()
We set tracing_buffers_fops.llseek to no_llseek,
but we can still perform pread() to read this file.
That is not expected.
This fix uses nonseekable_open() to disable it.
tracing_buffers_fops.llseek is still set to no_llseek,
it mark this file is a "non-seekable device" and is used by
sys_splice(). See also do_splice() or manual of splice(2):
ERRORS
EINVAL Target file system doesn't support splicing;
neither of the descriptors refers to a pipe;
or offset given for non-seekable device.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
LKML-Reference: <49D46668.8030806@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: consolidate documents
blktrace: pass the right pointer to kfree()
tracing/syscalls: use a dedicated file header
tracing: append a comma to INIT_FTRACE_GRAPH
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: do not count frozen tasks toward load
sched: refresh MAINTAINERS entry
sched: Print sched_group::__cpu_power in sched_domain_debug
cpuacct: add per-cgroup utime/stime statistics
posixtimers, sched: Fix posix clock monotonicity
sched_rt: don't allocate cpumask in fastpath
cpuacct: make cpuacct hierarchy walk in cpuacct_charge() safe when rcupreempt is used -v2
Impact: performance regression fix for s390
The adaptive spinning mutexes will not always do what one would expect on
virtualized architectures like s390. Especially the cpu_relax() loop in
mutex_spin_on_owner might hurt if the mutex holding cpu has been scheduled
away by the hypervisor.
We would end up in a cpu_relax() loop when there is no chance that the
state of the mutex changes until the target cpu has been scheduled again by
the hypervisor.
For that reason we should change the default behaviour to no-spin on s390.
We do have an instruction which allows to yield the current cpu in favour of
a different target cpu. Also we have an instruction which allows us to figure
out if the target cpu is physically backed.
However we need to do some performance tests until we can come up with
a solution that will do the right thing on s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
LKML-Reference: <20090409184834.7a0df7b2@osiris.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix perf-report output for /home mounted binaries, etc.
dentry_path() only provide path-names up to the mount root, which is
unsuited for out purpose, use d_path() instead.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090409085524.601794134@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add sysctl for paranoid/relaxed perfcounters policy
Allow the use of system wide perf counters to everybody, but provide
a sysctl to disable it for the paranoid security minded.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090409085524.514046352@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: performance optimization
The mmap/comm tracking code does quite a lot of work before it discovers
there's no interest in it, avoid that by keeping a counter.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090409085524.427173196@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: micro-optimization
Under group scheduling we traverse up until we are at common siblings
to make the wakeup comparison on.
At this point however, they should have the same parent so continuing
to check up the tree is redundant.
Signed-off-by: Paul Turner <pjt@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <alpine.DEB.1.00.0904081520320.30317@kitami.corp.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix kfree crash with non-standard act_mask string
If passing a string with leading white spaces to strstrip(),
the returned ptr != the original ptr.
This bug was introduced by me.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <49DD694C.8020902@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix build warnings and possibe compat misbehavior on IA64
Building a kernel on ia64 might trigger these ugly build warnings:
CC arch/ia64/ia32/sys_ia32.o
In file included from arch/ia64/ia32/sys_ia32.c:55:
arch/ia64/ia32/ia32priv.h:290:1: warning: "elf_check_arch" redefined
In file included from include/linux/elf.h:7,
from include/linux/module.h:14,
from include/linux/ftrace.h:8,
from include/linux/syscalls.h:68,
from arch/ia64/ia32/sys_ia32.c:18:
arch/ia64/include/asm/elf.h:19:1: warning: this is the location of the previous definition
[...]
sys_ia32.c includes linux/syscalls.h which in turn includes linux/ftrace.h
to import the syscalls tracing prototypes.
But including ftrace.h can pull too much things for a low level file,
especially on ia64 where the ia32 private headers conflict with higher
level headers.
Now we isolate the syscall tracing headers in their own lightweight file.
Reported-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jason Baron <jbaron@redhat.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Jiaying Zhang <jiayingz@google.com>
Cc: Michael Rubin <mrubin@google.com>
Cc: Martin Bligh <mbligh@google.com>
Cc: Michael Davidson <md@google.com>
LKML-Reference: <20090408184058.GB6017@nowhere>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: circular locking bugfix
The various implemetnations and proposed implemetnations of work_on_cpu()
are vulnerable to various deadlocks because they all used queues of some
form.
Unrelated pieces of kernel code thus gained dependencies wherein if one
work_on_cpu() caller holds a lock which some other work_on_cpu() callback
also takes, the kernel could rarely deadlock.
Fix this by creating a short-lived kernel thread for each work_on_cpu()
invokation.
This is not terribly fast, but the only current caller of work_on_cpu() is
pci_call_probe().
It would be nice to find some other way of doing the node-local
allocations in the PCI probe code so that we can zap work_on_cpu()
altogether. The code there is rather nasty. I can't think of anything
simple at this time...
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
kthreadd is the single thread which implements ths "create" request, move
sched_setscheduler/etc from create_kthread() to kthread_create() to
improve the scalability.
We should be careful with sched_setscheduler(), use _nochek helper.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Vitaliy Gusev <vgusev@openvz.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Remove the unnecessary find_task_by_pid_ns(). kthread() can just
use "current" to get the same result.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This fixes all the checkpatch --file complaints about kernel/ptrace.c
and also removes an unused #include. I've verified that there are no
changes to the compiled code on x86_64.
Signed-off-by: Roland McGrath <roland@redhat.com>
[ Removed the parts that just split a line - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul suggested we allow for data addresses to be recorded along with
the traditional IPs as power can provide these.
For now, only the software pagefault events provide data addresses,
but in the future power might as well for some events.
x86 doesn't seem capable of providing this atm.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090408130409.394816925@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move PERF_RECORD_TIME so that all the fixed length items come before
the variable length ones.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090408130409.307926436@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar