This driver adds support for loading Intel Integrated Sensor Hub (ISH) firmware
from host file system to ISH SRAM and start execution.
At power-on, the ISH subsystem shall boot to an interim Shim loader-firmware,
which shall expose an ISHTP loader device.
The driver implements an ISHTP client that communicates with the Shim ISHTP
loader device over the intel-ish-hid stack, to download the main ISH firmware.
Signed-off-by: Rushikesh S Kadam <rushikesh.s.kadam@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Nick Crews <ncrews@chromium.org>
Tested-by: Jett Rink <jettrink@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to HUTRR89 usage 0x1cb from the consumer page was assigned to
allow launching desktop-aware assistant application, so let's add the
mapping.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Recent kernels allow the generic-hid driver to be used as fallback for
devices with a specialized driver, when the hiddev is not listed in
hid_have_special_driver. Over time we are removing more and more
devices from the hid_have_special_driver table as devices get tested
to support this setup.
Before this commit the following happens when a HID device which has a
special-driver and is no longer listed in hid_have_special_driver, gets
enumerated:
1) device_add() gets called
2) bus_add_device() looks for a matching already registered hid driver,
and bind hid-generic to the new device
3) kobject_uevent(&dev->kobj, KOBJ_ADD) gets called notifying userspace of
the new hid_dev. udev calls modprobe based on the modalias in the uevent
4) The special driver gets loaded by modprobe
5) __hid_bus_reprobe_drivers() unbinds hid-generic and binds the new driver
There are a couple of downsides to this:
a) The probing messages printend when a HID driver bounds show up twice in
dmesg, which is confusing for the user
b) The (un)binding typically causes one or more evdev device-nodes to get
(un)registered firing of udev events to which e.g. the xserver responds by
(un)registering xinput devices and reporting this to interested clients.
IOW the i. bind generic, ii. unbind generic, iii. bind special driver dance
sets in motion a whole chain of events each step, while we really only want
the events from step iii. to be reported to userspace.
This commits introduces a request_module call before the device_add()
call, so that the special-driver is loaded when step 2) looks for a
matching driver and we directly bind the specialized driver.
Note the request_module call translates to an execve("/sbin/modprobe", ...)
and we now do this for each HID device added. So this is not entirely free,
but adding HID devices is not something which happens 100s of times a
second, so this should be fine.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[bentiss: fixed typo in commit message found by checkpatch.pl]
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
As seen on some USB wireless keyboards manufactured by Primax, the HID
parser was using some assumptions that are not always true. In this case
it's s the fact that, inside the scope of a main item, an Usage Page
will always precede an Usage.
The spec is not pretty clear as 6.2.2.7 states "Any usage that follows
is interpreted as a Usage ID and concatenated with the Usage Page".
While 6.2.2.8 states "When the parser encounters a main item it
concatenates the last declared Usage Page with a Usage to form a
complete usage value." Being somewhat contradictory it was decided to
match Window's implementation, which follows 6.2.2.8.
In summary, the patch moves the Usage Page concatenation from the local
item parsing function to the main item parsing function.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Terry Junge <terry.junge@poly.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
We have a new Dell laptop which has the synaptics I2C touchpad
(06cb:7e7e) on it. After booting up the Linux, the touchpad doesn't
work, there is no interrupt when touching the touchpad, after
disable the runtime PM, everything works well.
I also tried the quirk of I2C_HID_QUIRK_DELAY_AFTER_SLEEP, it is
better after applied this quirk, there are interrupts but data it
reports is invalid.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to hidpp20_batterylevel_get_battery_info my Logitech K270
keyboard reports only 2 battery levels. This matches with what I've seen
after testing with batteries at varying level of fullness, it always
reports either 5% or 30%.
Windows reports "battery good" for the 30% level. I've captured an USB
trace of Windows reading the battery and it is getting the same info
as the Linux hidpp code gets.
Now that Linux handles these devices as hidpp devices, it reports the
battery as being low as it treats anything under 31% as low, this leads
to the user constantly getting a "Keyboard battery is low" warning from
GNOME3, which is very annoying.
This commit fixes this by changing the low threshold to anything under
30%, which I assume is what Windows does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove the hidpp_is_connected() function wrapper, and have the callers
directly call hidpp_root_get_protocol_version() instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simply always print the HID++ version on hidpp_root_get_protocol_version
success.
This also fixes the version not being printed when a HID++ device
connected through a receiver is already connected when the hidpp driver
is loaded.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Similar to commit edfc3722cf ("HID: quirks: Fix keyboard + touchpad on
Toshiba Click Mini not working"), the Lenovo Miix 630 has a combo
keyboard/touchpad device with vid:pid of 04F3:0400, which is shared with
Elan touchpads. The combo on the Miix 630 has an ACPI id of QTEC0001,
which is not claimed by the elan_i2c driver, so key on that similar to
what was done for the Toshiba Click Mini.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Convert to use sysfs_streq() instead of custom approach.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to HUT 1.12 usage 0xb5 from the generic desktop page is reserved
for switching between external and internal display, so let's add the
mapping.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to HUT 1.12 usage 0x232 from the consumer page is reserved for
switching application between full screen and windowed mode, so let's add
the mapping.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to HUTRR73 usages 0x79, 0x7a and 0x7c from the consumer page
correspond to Brightness Up/Down/Toggle keys, so let's add the mappings.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to HUTRR77 usage 0x29f from the consumer page is reserved for
the Desktop application to present all running user’s application windows.
Linux defines KEY_SCALE to request Compiz Scale (Expose) mode, so let's
add the mapping.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to HUTRR37 usage 0x6d from the consumer usage page corresponds
to action that selects the next available supported aspect ratio option
on a device which outputs or displays video. However KEY_ZOOM means
activate "Full Screen" mode, KEY_ASPECT_RATIO should be used instead.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
hidpp_scroll_counter_handle_scroll() doesn't expect a 0-value scroll event, it
gets interpreted as a negative scroll direction event. This can cause scroll
direction resets and thus broken scrolling.
Fixes: 4435ff2f09 ("HID: logitech: Enable high-resolution scrolling on Logitech mice")
Cc: stable@vger.kernel.org # v5.0
Reported-and-tested-by: Aimo Metsälä <aimetsal@outlook.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
There is a race condition that could happen if hid_debug_rdesc_show()
is running while hdev is in the process of going away (device removal,
system suspend, etc) which could result in NULL pointer dereference:
BUG: unable to handle kernel paging request at 0000000783316040
CPU: 1 PID: 1512 Comm: getevent Tainted: G U O 4.19.20-quilt-2e5dc0ac-00029-gc455a447dd55 #1
RIP: 0010:hid_dump_device+0x9b/0x160
Call Trace:
hid_debug_rdesc_show+0x72/0x1d0
seq_read+0xe0/0x410
full_proxy_read+0x5f/0x90
__vfs_read+0x3a/0x170
vfs_read+0xa0/0x150
ksys_read+0x58/0xc0
__x64_sys_read+0x1a/0x20
do_syscall_64+0x55/0x110
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Grab driver_input_lock to make sure the input device exists throughout the
whole process of dumping the rdesc.
[jkosina@suse.cz: update changelog a bit]
Signed-off-by: he, bo <bo.he@intel.com>
Signed-off-by: "Zhang, Jun" <jun.zhang@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of directly accessing PCI device poitner via struct ishtp_cl,
create interface function for same. This is required for DMA transfer.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only include intel-ish-client-if.h, which has all interfaces required to
implment ISHTP client. There is no longer any direct field access from
core ISHTP only include files.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move function idefinitions related to bus and device to common header file.
Also create new function to get fw client id and move ish_hw_reset() from
inline to exported function.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move the interface functions in client.h to common include. These are
already abstracted well to use as is. Also move any associated structures
used by these functions.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Store ishtp_cl_device pointer in device struct private data. In this
way we can get ishtp_cl_device * from device struct pointer.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move the driver registry with the ishtp bus to the common interface
file, which clients can include.
Also rename __ishtp_cl_driver_register() to ishtp_cl_driver_register()
and removed define for ishtp_cl_driver_register.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All callers will only use ISHTP_HOST_CLIENT_ID_ANY, so get rid of
option to pass this additional id.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ISH clients don't need to access any field of struct ishtp_cl_device. To
avoid this create an interface functions instead where it is required.
In the case of ishtp_cl_allocate(), modify the parameters so that the
clients don't have to dereference.
Clients can also use tracing, here a new interface is added to get the
common trace function pointer, instead of direct call.
The new interface functions defined in one external header file, named
intel-ish-client-if.h. This is the only header files all ISHTP clients
must include.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently we depend on the guid check in ishtp_cl_driver.probe to match
the device and driver. However Linux device core first calls the match()
callback to decide the matching of driver and device, and then does some
preparation before calling the driver probe function. If we return error
in the driver probe, it needs to tear down all the preparation work and
retry with next driver.
Adding the match callback can avoid the unnecessary entry into unmatched
driver probe function for ishtp clients reported by FW.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
create_singlethread_workqueue may fail and return NULL. The fix checks if it is
NULL to avoid NULL pointer dereference. Also, the fix moves the call of
create_singlethread_workqueue earlier to avoid resource-release issues.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 71f6fa90a3 ("HID: increase maximum global item tag report size
to 256") increases the max report size from 128 to 256.
We also need to update the report size in hid_field_extract() otherwise
it complains and truncates now valid report size:
[ 406.165461] hid-sensor-hub 001F:8086:22D8.0002: hid_field_extract() called with n (192) > 32! (kworker/5:1)
BugLink: https://bugs.launchpad.net/bugs/1818547
Fixes: 71f6fa90a3 ("HID: increase maximum global item tag report size to 256")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Raw interface is often used to update firmwares in HID devices.
We are enabling the interface to support in-field firmware update
for the HID devices attached to ISH.
Signed-off-by: Hyungwoo Yang <hyungwoo.yang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When using this driver with the wireless dongle and some usermode
program that monitors every input device (acpid, for example), while
another usermode client opens and closes the low-level device
repeadedly, the system eventually deadlocks.
The reason is that steam_input_register_device() must not be called with
the mutex held, because the input subsystem has its own synchronization
that clashes with this one: it is possible that steam_input_open() is
called before input_register_device() returns, and since
steam_input_open() needs to lock the mutex, it deadlocks.
However we must hold the mutex when calling any function that sends
commands to the controller. If not, random commands end up falling fail.
Reported-by: Simon Gene Gottlieb <simon@gottliebtfreitag.de>
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Tested-by: Simon Gene Gottlieb <simon@gottliebtfreitag.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently ver_ptr is being null checked twice, once before calling
usb_string and once afterwards. The second null check is redundant
and can be removed, remove it.
Detected by CoverityScan, CID#1477308 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The kernel-doc annotation is misused for hid_mouse_ignore_list. The script
complains about it:
drivers/hid/hid-quirks.c:894: warning: cannot understand function prototype: 'const struct hid_device_id hid_mouse_ignore_list[] = '
Drop the annotation to make script happy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The newly added power supply code fails to link when the power supply core
code is disabled:
drivers/hid/hid-asus.o: In function `asus_battery_get_property':
hid-asus.c:(.text+0x11de): undefined reference to `power_supply_get_drvdata'
drivers/hid/hid-asus.o: In function `asus_probe':
hid-asus.c:(.text+0x170c): undefined reference to `devm_power_supply_register'
hid-asus.c:(.text+0x1734): undefined reference to `power_supply_powers'
drivers/hid/hid-asus.o: In function `asus_raw_event':
hid-asus.c:(.text+0x1914): undefined reference to `power_supply_changed'
Select the subsystem from Kconfig as we do for other hid drivers already.
Fixes: 6311d329e1 ("HID: hid-asus: Add BT keyboard dock battery monitoring support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
When building with -Wformat, clang warns:
drivers/hid/hid-quirks.c:1075:27: warning: format specifies type
'unsigned short' but the argument has type '__u32' (aka 'unsigned int')
[-Wformat]
bl_entry->driver_data, bl_entry->vendor,
^~~~~~~~~~~~~~~~
./include/linux/hid.h:1170:48: note: expanded from macro 'dbg_hid'
printk(KERN_DEBUG "%s: " format, __FILE__, ##arg); \
~~~~~~ ^~~
drivers/hid/hid-quirks.c:1076:4: warning: format specifies type
'unsigned short' but the argument has type '__u32' (aka 'unsigned int')
[-Wformat]
bl_entry->product);
^~~~~~~~~~~~~~~~~
./include/linux/hid.h:1170:48: note: expanded from macro 'dbg_hid'
printk(KERN_DEBUG "%s: " format, __FILE__, ##arg); \
~~~~~~ ^~~
drivers/hid/hid-quirks.c:1242:12: warning: format specifies type
'unsigned short' but the argument has type '__u32' (aka 'unsigned int')
[-Wformat]
quirks, hdev->vendor, hdev->product);
^~~~~~~~~~~~
./include/linux/hid.h:1170:48: note: expanded from macro 'dbg_hid'
printk(KERN_DEBUG "%s: " format, __FILE__, ##arg); \
~~~~~~ ^~~
drivers/hid/hid-quirks.c:1242:26: warning: format specifies type
'unsigned short' but the argument has type '__u32' (aka 'unsigned int')
[-Wformat]
quirks, hdev->vendor, hdev->product);
^~~~~~~~~~~~~
./include/linux/hid.h:1170:48: note: expanded from macro 'dbg_hid'
printk(KERN_DEBUG "%s: " format, __FILE__, ##arg); \
~~~~~~ ^~~
4 warnings generated.
This patch fixes the format strings to use the correct format type for unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Louis Taylor <louis@kragniz.eu>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Power management improvements from Song Hongyan
Switch to new UUID API from Andy Shevchenko
Generalization the driver bindin to support more than just sensors from Srinivas Pandruvada
Tested with a Waltop tablet and it seems to work fine.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested with one KYE tablet and it seems to work fine.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested with a couple UC-Logic tablets and it seems to work fine.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Do not try to initialize UC-Logic tablets if the underlying device is
not a USB device, but e.g. a uhid device.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add support for Ugee G5 to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add support for converting Gray-coded rotary encoder input into dial
input compatible with HID standard. Needed for Ugee G5 support.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add support for inserting a Wacom pad device ID into hid-uclogic
reports. This allows reporting dial inputs in a way compatible with the
Wacom driver. Needed for Ugee G5 support in particular.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add support for XP-Pen Deco 01 to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add support for XP-Pen Star G640 to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add support for XP-Pen Star G540 to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add proper support for Ugee EX07(S) frame controls to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add support for Ugee M540 to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add support for Ugee 2150 to hid-uclogic.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add support for UC-Logic v2 protocol to hid-uclogic.
This adds support for a bunch of new Huion models.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Support parsing fragmented high-resolution reports in hid-uclogic to
support v2 reporting protocol.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Newer UC-Logic tablets, such as ones made by Huion have stopped
reporting in-range state, but they're otherwise worthy tablets. The
manufacturer was notified of the problem and promised to fix this in the
future. Meanwhile, detect pen coming in range, and emulate the reports
to the userspace, to make the tablets useable.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Designate the current UC-Logic tablet initialization protocol v1, in
preparation for adding support for v2 protocol.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Re-initialize UC-Logic tablets on resume. UC-Logic tablet initialization
and parameter retrieval cannot be separated for the large part, so
simply discard the retrieved parameters after initialization.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Refactor and extract UC-Logic tablet initialization and parameter
discovery into a module. For these tablets, the major part of parameter
discovery cannot be separated from initialization so they have to be in
the same module. Define explicitly and clearly what possible quirks the
tablets may have to make the driver implementation easier and simpler.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
As hid-uclogic has a lot of report descriptors already and there's going
to be more, move them out of the driver code and into a separate module.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add "_UCLOGIC" to Ugee tablet device ID macros so it's clear they come
with UC-Logic vendor ID.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add support for ViewSonic PD1011 signature (display) pad, which is also
sold by Signotec under a different name.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Originally contributed by Andrey Alekseenko <al42and@gmail.com>.
Signed-off-by: Andrey Alekseenko <al42and@gmail.com>
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Wacom has introduced a new pen compatible with its MobileStudio Pro and
other tablets. Although adding it to the tool ID tablet is not strictly
necessary unrecognized pens are reported as BTN_TOOL_PEN already, unless
the tablet sends the "eraser" bit, when BTN_TOOL_RUBBER is used instead),
we'll keep it updated anyway.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/hid/hid-roccat-kone.c: In function ‘kone_keep_values_up_to_date’:
drivers/hid/hid-roccat-kone.c:784:20: warning: this statement may fall through [-Wimplicit-fallthrough=]
kone->actual_dpi = kone->profiles[event->value - 1].
~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
startup_dpi;
~~~~~~~~~~~
drivers/hid/hid-roccat-kone.c:786:2: note: here
case kone_mouse_event_osd_profile:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of using an 128-byte on-stack array to store the request, we can
instantiate the request on stack directly. This can save the stack usage of
these functions, since most of the requests are much smaller than 128 bytes.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Tested-by: Hongyan Song <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reading of IPC_REG_ISH_HOST_FWSTS will flush both message register
and doorbell. So move the doorbell write before reading of
IPC_REG_ISH_HOST_FWSTS.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Tested-by: Hongyan Song <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently we are using one additional static variable and a spinlock to
prevent contention of writing IPC messages to ISH hardware, which is
not necessary. Once ISH is ready to accept new data, we can push new
data to hardware. This pushing of new data is already protected by
wr_processing_spinlock for contention, which is enough. So use this
spinlock to check both readiness for accepting new data and once ready
allow writing of ipc message from queue to ISH hardware.
While here, cleaned up some space after return.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Tested-by: Hongyan Song <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When performing a warm reset in ishtp bus driver, the ishtp_cl_device
will not be removed, its fw_client still points to the already freed
ishtp_device.fw_clients array.
Later after driver finishing ishtp client enumeration, this dangling
pointer may cause driver to bind the wrong ishtp_cl_device to the new
client, causing wrong callback to be called for messages intended for
the new client.
This helps in development of firmware where frequent switching of
firmwares is required without Linux reboot.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Tested-by: Hongyan Song <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/hid/wacom_wac.c: In function ‘wacom_setup_pen_input_capabilities’:
drivers/hid/wacom_wac.c:3506:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
__clear_bit(ABS_MISC, input_dev->absbit);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/hid/wacom_wac.c:3508:2: note: here
case WACOM_MO:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Logitech WingMan Formula GP by default presents a combined
accelerate/brake axis, so this patch assigns it to hid-logitech in order to
benefit from the axis-splitting logic in lg4ff. There is also a fixed
report descriptor for the resulting report.
Signed-off-by: Jarrad Whitaker <jarrad.whitaker@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the trackpoint and three mouse buttons on the type cover
of the Lenovo X1 Tablet Gen3.
This is the same as with the 2nd generation Lenovo X1 Tablet.
Signed-off-by: Mikael Wikström <leakim.wikstrom@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a new firmware for the Steam Controller with support for BLE
connections. When using such a device with a wired connection, it
reboots itself every 10 seconds unless an application has opened it.
Doing hid_hw_open() unconditionally on probe fixes the issue, and the
code becomes simpler.
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add ASUS Transbook T100CHI/T90CHI keyboard dock into battery quirk list, in
order to add specific implementation in hid-asus.
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Transbook T90CHI support into hid-asus.
T90CHI returns same BT vendor/product values as T100CHI, so identifies T90CHI
by name.
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The bluetooth-keyboard which comes with the Toshiba WT10A tablet uses
a couple of usage codes in the vendor specific ffbc page.
The keyboard has a vendor-id of 04f2 which maps to Chicony.
Other then adding a few keymappings for the ffbc usages, no special
handling is necessary. So rather then adding a new hid-toshiba driver,
this commit adds the ID and 2 extra key-mappings to the hid-topseed
driver. The hid-topseed driver already contains mapping for some
ffbc usages (and does nothing else) and it already binds to another
Chicony manufactured keyboard.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The Intel ISH HID can now have other devices attached to it, not just
sensors. Hence ISH HID transport is no longer just used for sensors.
Currently the vendor and product id is hardcoded for sensors, but they
can be obtained from ISH firmware for the real device. The driver already
extract them and store as part of device_info structure in client_data.
So use vendor id/product id obtained from the ISH firmware.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Ring buffer implementation in hid_debug_event() and hid_debug_events_read()
is strange allowing lost or corrupted data. After commit 717adfdaf1
("HID: debug: check length before copy_to_user()") it is possible to enter
an infinite loop in hid_debug_events_read() by providing 0 as count, this
locks up a system. Fix this by rewriting the ring buffer implementation
with kfifo and simplify the code.
This fixes CVE-2019-3819.
v2: fix an execution logic and add a comment
v3: use __set_current_state() instead of set_current_state()
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1669187
Cc: stable@vger.kernel.org # v4.18+
Fixes: cd667ce247 ("HID: use debugfs for events/reports dumping")
Fixes: 717adfdaf1 ("HID: debug: check length before copy_to_user()")
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The 'wacom_hid_usage_quirk' function is the intended home for fixing
up descriptors that are buggy or that don't quite fit the mold. Commit
578325120e was supposed to move all of these quirks but it missed the
code to handle fixup the serial number usages for AES pens. Lets move
this code out of 'wacom_wac_pen_usage_mapping' where it was previously
lurking and put it into the same place as the others.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Don't populate the array buf on the stack but instead make it
static. Makes the object code smaller by 43 bytes:
Before:
text data bss dec hex filename
7769 1520 0 9289 2449 drivers/hid/hid-elan.o
After:
text data bss dec hex filename
7662 1584 0 9246 241e drivers/hid/hid-elan.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Host driver should handle interrupt mask register earlier than wake up ish FW
else there will be conditions when FW interrupt comes, host PIMR register still
not set ready, so move the interrupt mask setting before ish_wakeup.
Clear PISR busy_clear bit in ish_irq_handler. If not clear, there will be
conditions host driver received a busy_clear interrupt (before the busy_clear
mask bit is ready), it will return IRQ_NONE after check_generated_interrupt,
the interrupt will never be cleared, causing the DEVICE not sending following
IRQ.
Since PISR clear should not be called for the CHV device we do this change.
After the change, both ISH2HOST interrupt and busy_clear interrupt will be
considered as interrupt from ISH, busy_clear interrupt will return IRQ_HANDLED
from IPC_IS_BUSY check.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
While using Elan touchpads, the message floods:
[ 136.138487] i2c_hid i2c-DELL08D6:00: i2c_hid_get_input: incomplete report (14/65535)
Though the message flood is annoying, the device it self works without
any issue. I suspect that the device in question takes too much time to
pull the IRQ back to high after I2C host has done reading its data.
Since the host receives all useful data, let's ignore the input report
when there's no data.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Manually tracking an active collection to set collection parents is not
necessary, we just have to look one step back into the collection stack
to find the correct parent.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The USB report descriptor sent by the Maltron L90 keyboard is invalid,
causing the media key reports not to be accepted.
This patch adds a driver which uses a report fixup to replace the
descriptor.
Signed-off-by: William Whistler <wtbw@wtbw.co.uk>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
A Goodix touchpad doesn't work. Touching the touchpad can trigger IRQ
but there's no input event from HID subsystem.
Turns out it reports some invalid data:
[ 22.136630] i2c_hid i2c-DELL091F:00: input: 0b 00 01 00 00 00 00 00 00 00 00
After some trial and error, it's another device that doesn't work well
with ON/SLEEP commands. Disable runtime PM to fix the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously, the pointer to the parent collection was stored. If a device
exceeds 16 collections (HID_DEFAULT_NUM_COLLECTIONS), the array to store
the collections is reallocated, the pointer to the parent collection becomes
invalid.
Replace the pointers with an index-based lookup into the collections array.
Fixes: c53431eb69 ("HID: core: store the collections as a basic tree")
Reported-by: Pandruvada, Srinivas <srinivas.pandruvada@intel.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Tested-by: Kyle Pelton <kyle.d.pelton@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rumble support on SHANWAN PS3 gamepad is not working when a user
program has asked it to. If a HID Output Reports is sent via Control
Channel then it will be discard by gamepad, thus rumble motor and led
settings in Output Report are ignored.
This patch therefore sends HID Output Report via Interrupt Channel to
SHANWAN gamepad instead of Control Channel, fixing rumble motor and
led settings.
Signed-off-by: Hongye Yuan <outmatch@gmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Transform the one-time check for a SHANWAN PS3 clone gamepad into a
quirk, to avoid doing the same string comparison in multiple places.
Signed-off-by: Hongye Yuan <outmatch@gmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Pull HID updates from Jiri Kosina:
- high-resolution scrolling support that gracefully handles differences
between MS and Logitech implementations in HW, from Peter Hutterer
and Harry Cutts
- MSI IRQ support for intel-ish driver, from Song Hongyan
- support for new hardware (Cougar 700K, Odys Winbook 13, ASUS FX503VD,
ASUS T101HA) from Daniel M. Lambea, Hans de Goede and Aleix Roca
Nonell
- other small assorted fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (22 commits)
HID: i2c-hid: Add Odys Winbook 13 to descriptor override
HID: lenovo: Add checks to fix of_led_classdev_register
HID: intel-ish-hid: add MSI interrupt support
HID: debug: Change to use DEFINE_SHOW_ATTRIBUTE macro
HID: doc: fix wrong data structure reference for UHID_OUTPUT
HID: intel-ish-hid: fixes incorrect error handling
HID: asus: Add support for the ASUS T101HA keyboard dock
HID: logitech: Use LDJ_DEVICE macro for existing Logitech mice
HID: logitech: Enable high-resolution scrolling on Logitech mice
HID: logitech: Add function to enable HID++ 1.0 "scrolling acceleration"
HID: logitech-hidpp: fix typo, hiddpp to hidpp
HID: input: use the Resolution Multiplier for high-resolution scrolling
HID: core: process the Resolution Multiplier
HID: core: store the collections as a basic tree
Input: add `REL_WHEEL_HI_RES` and `REL_HWHEEL_HI_RES`
HID: input: support Microsoft wireless radio control hotkey
HID: use macros in IS_INPUT_APPLICATION
HID: asus: Add support for the ASUS FX503VD laptop
HID: asus: Add event handler to catch unmapped Asus Vendor UsagePage codes
HID: cougar: Add support for Cougar 700K Gaming Keyboard
...
The Odys Winbook 13 uses a SIPODEV SP1064 touchpad, which does not
supply descriptors, add this to the DMI descriptor override list, fixing
the touchpad not working.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1526312
Reported-by: Rene Wagner <redhatbugzilla@callerid.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In lenovo_probe_tpkbd(), the function of_led_classdev_register() could
return an error value that is unchecked. The fix adds these checks.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Core changes:
- Some core changes are already in outside of this pull
request as they came through the regulator tree, most
notably devm_gpiod_unhinge() that removes devres refcount
management from a GPIO descriptor. This is needed in
subsystems such as regulators where the regulator core
need to take over the reference counting and lifecycle
management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match()
as nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This
helps setting the direction now that we are two GPIO
maintainers.
- Handle the MMC CD/WP properties in the device tree core.
(The bulk of patches activating this code is already
merged through the MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so
we as gpiochips can request lines as active low or open
drain etc even from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has
been around for ages, and is now modernized to reduce code
duplication that has stacked up and is using regmap to read
write and cache registers.
- Intel drivers are now maintained in a separate tree and
start with a round of cleanups and unifications.
-----BEGIN PGP SIGNATURE-----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=05LW
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.21 kernel series.
Core changes:
- Some core changes are already in outside of this pull request as
they came through the regulator tree, most notably
devm_gpiod_unhinge() that removes devres refcount management from a
GPIO descriptor. This is needed in subsystems such as regulators
where the regulator core need to take over the reference counting
and lifecycle management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This helps
setting the direction now that we are two GPIO maintainers.
- Handle the MMC CD/WP properties in the device tree core. (The bulk
of patches activating this code is already merged through the
MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so we as
gpiochips can request lines as active low or open drain etc even
from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has been
around for ages, and is now modernized to reduce code duplication
that has stacked up and is using regmap to read write and cache
registers.
- Intel drivers are now maintained in a separate tree and start with
a round of cleanups and unifications"
* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
gpio: sama5d2-piobu: Depend on OF_GPIO
gpio: Add Cadence GPIO driver
dt-bindings: gpio: Add bindings for Cadence GPIO
gpiolib-acpi: remove unused variable 'err', cleans up build warning
gpio: mxs: read pin level directly instead of using .get
gpio: aspeed: remove duplicated statement
gpio: add driver for SAMA5D2 PIOBU pins
dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
gpio/mmc/of: Respect polarity in the device tree
dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
memory: omap-gpmc: Get the header of the enum
ARM: omap1: Fix new user of gpiochip_request_own_desc()
gpio: pca953x: Add regmap dependency for PCA953x driver
gpio: raspberrypi-exp: decrease refcount on firmware dt node
gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
gpio: pca953x: Restore registers after suspend/resume cycle
gpio: pca953x: Zap single use of pca953x_read_single()
gpio: pca953x: Zap ad-hoc reg_output cache
gpio: pca953x: Zap ad-hoc reg_direction cache
gpio: pca953x: Perform basic regmap conversion
...
Now ish hid ipc only support sideband interrupt but on some platforms
they use MSI interrupt.
In order to make the interrupt type coverage all the scenario add
single MSI interrupt support, it can match all interrupt types.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The memory chunk allocated by hid_allocate_device() should be released
by hid_destroy_device(), not kfree().
Fixes: 0b28cb4bcb1("HID: intel-ish-hid: ISH HID client driver")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ASUS T101HA keyboard dock generates HID events using the ASUS vendor
specific UsagePage 0xff31. In consequence, some multimedia keys such as
brightness up and down are not working with hid-generic.
This commit adds the T101HA dock into the supported device list of the
hid-asus driver. It also prevents the dock's integrated touchpad to be
bound with hid-asus given that it is already working fine with
hid-multitouch.
Signed-off-by: Aleix Roca Nonell <kernelrocks@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Before things go out of hand, make it possible to pass
flags when requesting "own" descriptors from a gpio_chip.
This is necessary if the chip wants to request a GPIO with
active low semantics, for example.
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull HID subsystem fixes from Jiri Kosina:
- two device-specific quirks from Hans de Goede and Nic Soudée
- reintroduction of (mistakenly remocved) ABS_RESERVED from Peter
Hutterer
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
Input: restore EV_ABS ABS_RESERVED
HID: quirks: fix RetroUSB.com devices
HID: ite: Add USB id match for another ITE based keyboard rfkill key quirk
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
There are three features used by various Logitech mice for
high-resolution scrolling: the scrolling acceleration bit in HID++ 1.0,
and the x2120 and x2121 features in HID++ 2.0 and above. This patch
supports all three, and uses the multiplier reported by the mouse for
the HID++ 2.0+ features.
The full list of product IDs of mice which support high-resolution
scrolling was provided by Logitech, but the patch was tested using the
following mice (using the Unifying receiver):
* HID++ 1.0: Anywhere MX, Performance MX
* x2120: M560
* x2121: MX Anywhere 2, MX Master 2S
This patch is a combinations of the now-reverted commits 1ff2e1a44e,
d56ca9855b, 5fe2ccbef9, 044ee89028 together with some extra bits for the
directional and timeout-based reset.
The previous patch series was in hid-input, it appears this remainder
handling is logitech-specific and was moved to hid-logitech-hidpp.c and
renamed accordingly.
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
"Scrolling acceleration" is a bit of a misnomer: it doesn't deal with
acceleration at all. However, that's the name used in Logitech's spec,
so I used it here.
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Windows uses a magic number of 120 for a wheel click. High-resolution
scroll wheels are supposed to use a fraction of 120 to signal smaller
scroll steps. This is implemented by the Resolution Multiplier in the
device itself.
If the multiplier is present in the report descriptor, set it to the
logical max and then use the resolution multiplier to calculate the
high-resolution events. This is the recommendation by Microsoft, see
http://msdn.microsoft.com/en-us/windows/hardware/gg487477.aspx
Note that all mice encountered so far have a logical min/max of 0/1, so
it's a binary "yes or no" to high-res scrolling anyway.
To make userspace simpler, always enable the REL_WHEEL_HI_RES bit. Where
the device doesn't support high-resolution scrolling, the value for the
high-res data will simply be a multiple of 120 every time. For userspace,
if REL_WHEEL_HI_RES is available that is the one to be used.
Potential side-effect: a device with a Resolution Multiplier applying to
other Input items will have those items set to the logical max as well.
This cannot easily be worked around but it is doubtful such devices exist.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The Resolution Multiplier is a feature report that modifies the value of
Usages within the same Logical Collection. If the multiplier is set to
anything but 1, the hardware reports (value * multiplier) for the same amount
of physical movement, i.e. the value we receive in the kernel is
pre-multiplied.
The hardware may either send a single (value * multiplier), or by sending
multiplier as many reports with the same value, or a combination of these two
options. For example, when the Microsoft Sculpt Ergonomic mouse Resolution
Multiplier is set to 12, the Wheel sends out 12 for every detent but AC Pan
sends out a value of 3 at 4 times the frequency.
The effective multiplier is based on the physical min/max of the multiplier
field, a logical min/max of [0,1] with a physical min/max of [1,8] means the
multiplier is either 1 or 8.
The Resolution Multiplier was introduced for high-resolution scrolling in
Windows Vista and is commonly used on Microsoft mice.
The recommendation for the Resolution Multiplier is to default to 1 for
backwards compatibility. This patch adds an arbitrary upper limit at 255. The
only known use case for the Resolution Multiplier is for scroll wheels where the
multiplier has to be a fraction of 120 to work with Windows.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
For each collection parsed, store a pointer to the parent collection
(if any). This makes it a lot easier to look up which collection(s)
any given item is part of
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
SNES RetroPort and RetroPad register only 4 gamepad buttons
when they should register all 8 buttons. This is described here:
https://ask.fedoraproject.org/en/question/128102
This is happening because of:
Commit 190d7f02ce ("HID: input: do not increment usages when
duplicate is found")
Here, I add the quirk HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE
(created for backward compatibility with the change in 190d7f02ce)
for the two products.
Tested with both RetroPort and RetroPad.
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Nic Soudée <nsoudee@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Pull input updates from Dmitry Torokhov:
"Mostly new IDs for Elan/Synaptics touchpads, plus a few small fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: omap-keypad - fix keyboard debounce configuration
Input: xpad - quirk all PDP Xbox One gamepads
Input: synaptics - enable SMBus for HP 15-ay000
Input: synaptics - add PNP ID for ThinkPad P50 to SMBus
Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15ARR
Input: elan_i2c - add support for ELAN0621 touchpad
Input: hyper-v - fix wakeup from suspend-to-idle
Input: atkbd - clean up indentation issue
Input: st1232 - convert to SPDX identifiers
Input: migor_ts - convert to SPDX identifiers
Input: dt-bindings - fix a typo in file input-reset.txt
Input: cros_ec_keyb - fix button/switch capability reports
Input: elan_i2c - add ELAN0620 to the ACPI table
Input: matrix_keypad - check for errors from of_get_named_gpio()
Here are some small IIO and Staging driver fixes for 4.20-rc5.
Nothing major, the IIO fix ended up touching the HID drivers at the same
time, but the HID maintainer acked it. The staging fixes are all minor
patches for reported issues and regressions, full details are in the
shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXAFeeA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykZSQCgm8wafCzK2b9YjeUmAxFJQCKkK7YAnjHSqa8N
FwSpP/zei0mtZgw6Rzj9
=cBhw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some small IIO and staging driver fixes for 4.20-rc5.
Nothing major, the IIO fix ended up touching the HID drivers at the
same time, but the HID maintainer acked it. The staging fixes are all
minor patches for reported issues and regressions, full details are in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio/hid-sensors: Fix IIO_CHAN_INFO_RAW returning wrong values for signed numbers
staging: vchiq_arm: fix compat VCHIQ_IOC_AWAIT_COMPLETION
staging: mt7621-pinctrl: fix uninitialized variable ngroups
staging: rtl8723bs: Add missing return for cfg80211_rtw_get_station
staging: most: use format specifier "%s" in snprintf
staging: rtl8723bs: Fix incorrect sense of ether_addr_equal
staging: mt7621-dma: fix potentially dereferencing uninitialized 'tx_desc'
staging: comedi: clarify/unify macros for NI macro-defined terminals
drivers: staging: cedrus: find ctx before dereferencing it ctx
staging: rtl8723bs: Fix the return value in case of error in 'rtw_wx_read32()'
staging: comedi: ni_mio_common: scale ao INSN_CONFIG_GET_CMD_TIMING_CONSTRAINTS
iio:st_magn: Fix enable device after trigger
The ASUS FX503VD laptop uses an USB keyboard with several hotkeys
which use the Asus Vendor specific UsagePage.
This uses two usage-codes within the page which have not been seen
before, 0x7c for its mic-mute hotkey and 0x99 for Fn+F5 which has
a "fan" symbol as hotkey symbol on the keyb. we map this to KEY_PROG4
(PROG1-PROG3 are already used).
This commit adds the mappings for the 2 new usage codes and the USB-ids
for this keyboard to the hid-asus driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Various Asus devices generate HID events using the Asus Vendor specific
UsagePage 0xff31 and hid-asus will map these in its input_mapping for all
devices to which it binds (independent of any quirks).
Add an event callback which check for unmapped (because sofar unknown)
usages within the Asus Vendor UsagePage and log a warning for these.
The purpose of this patch is to help debugging / find such unmapped codes
and add them to the asus_input_mapping() function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The 258a:6a88 keyboard-dock shipped with the Prowise PT301 tablet is
likely another ITE based design. The controller die is directly bonded
to the PCB with a blob of black glue on top so there are no markings and
the 258a vendor-id used is unknown anywhere. But the keyboard has the
exact same hotkeys mapped to Fn+F1 - F10 as the other ITE8595 keyboard
I have *and* it has the same quirky behavior wrt the rfkill hotkey.
Either way as said this keyboard has the same quirk for its rfkill /
airplane mode hotkey as the ITE 8595 chip, it only sends a single release
event when pressed and released, it never sends a press event.
This commit adds the 258a:6a88 USB id to the hid-ite id-table, fixing
the rfkill key not working on this keyboard.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
* st_magn
- Avoid an ordering issue that lead to large numbers of unhandled
interrupts whilst enabling buffered capture.
* hid-sensors
- Fix a long running problem with signed values reading wrong from
sysfs on these sensors. It appears people were only using the
buffered interface. These typically occur in laptops so chances
are everyone was using the sensor-proxy which will use the buffered
interface by default.
-----BEGIN PGP SIGNATURE-----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=nVLE
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.20 cycle.
* st_magn
- Avoid an ordering issue that lead to large numbers of unhandled
interrupts whilst enabling buffered capture.
* hid-sensors
- Fix a long running problem with signed values reading wrong from
sysfs on these sensors. It appears people were only using the
buffered interface. These typically occur in laptops so chances
are everyone was using the sensor-proxy which will use the buffered
interface by default.
* tag 'iio-fixes-for-4.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio/hid-sensors: Fix IIO_CHAN_INFO_RAW returning wrong values for signed numbers
iio:st_magn: Fix enable device after trigger
This reverts commit 1ff2e1a44e.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 051dc9b057.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit d56ca9855b.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 3fe1d6bbcd.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 5fe2ccbef9.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 044ee89028.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Add USB ID 060b:700a to the list of valid USB IDS for the
cougar hid driver.
Signed-off-by: Daniel M. Lambea <dmlambea@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for two Primax mice as well.
0x4e22 is the Dell MS111-P and 0x4d0f is the unbranded HP Portia
mouse HP 697738-001. Both were built until approx. 2014.
Those were the standard mice from those vendors and are still
around - even as new old stock.
Reference: https://github.com/sriemer/fix-linux-mouse/issues/11
Signed-off-by: Sebastian Parschauer <sparschauer@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
LG touchscreen (1fd2:8001) stops working after reboot:
[ 4.859153] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 4.936070] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 9.948224] i2c_hid i2c-SAPS2101:00: failed to reset device.
The device in question stops working after receives SLEEP, ON, SLEEP
commands in a short period. The scenario is like this:
- Once the desktop session closes, it also closed the hid device, so the
device gets runtime suspended and receives a SLEEP command.
- Before calling shutdown callback, it gets runtime resumed and received
an ON command.
- In the shutdown callback, it receives another SLEEP command.
I failed to find a reliable interval between ON/SLEEP commands that can
make it work, so let's simply disable runtime PM for the device.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cirque Touchpad/Pointstick combo is similar to Alps devices, it requires
MT_CLS_WIN_8_DUAL to expose its pointstick as a mouse.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously, when a HID client such as the Steam Client was running, this
driver disabled its input device to avoid doubling the input events.
While it worked mostly fine, some games got confused by the idle gamepad,
and switched to two player mode, or asked the user to choose which gamepad
to use. Other games just crashed, probably a bug in Unity [1].
With this commit, when a HID client starts, the input device is removed;
when the HID client ends the input device is recreated.
[1]: https://github.com/ValveSoftware/steam-for-linux/issues/5645
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 336fd4f5f2.
Please note that `strlcpy()` does *NOT* do what you think it does.
strlcpy() *ALWAYS* reads the full input string, regardless of the
'length' parameter. That is, if the input is not zero-terminated,
strlcpy() will *READ* beyond input boundaries. It does this, because it
always returns the size it *would* copy if the target was big enough,
not the truncated size it actually copied.
The original code was perfectly fine. The hid device is
zero-initialized and the strncpy() functions copied up to n-1
characters. The result is always zero-terminated this way.
This is the third time someone tried to replace strncpy with strlcpy in
this function, and gets it wrong. I now added a comment that should at
least make people reconsider.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a UHID_CREATE command is written to the uhid char device, a
copy_from_user() is done from a user pointer embedded in the command.
When the address limit is KERNEL_DS, e.g. as is the case during
sys_sendfile(), this can read from kernel memory. Alternatively,
information can be leaked from a setuid binary that is tricked to write
to the file descriptor. Therefore, forbid UHID_CREATE in these cases.
No other commands in uhid_char_write() are affected by this bug and
UHID_CREATE is marked as "obsolete", so apply the restriction to
UHID_CREATE only rather than to uhid_char_write() entirely.
Thanks to Dmitry Vyukov for adding uhid definitions to syzkaller and to
Jann Horn for commit 9da3f2b740 ("x86/fault: BUG() when uaccess
helpers fault on kernel addresses"), allowing this bug to be found.
Reported-by: syzbot+72473edc9bf4eb1c6556@syzkaller.appspotmail.com
Fixes: d365c6cfd3 ("HID: uhid: add UHID_CREATE and UHID_DESTROY events")
Cc: <stable@vger.kernel.org> # v3.6+
Cc: Jann Horn <jannh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jann Horn <jannh@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Before this commit sensor_hub_input_attr_get_raw_value() failed to take
the signedness of 16 and 8 bit values into account, returning e.g.
65436 instead of -100 for the z-axis reading of an accelerometer.
This commit adds a new is_signed parameter to the function and makes all
callers pass the appropriate value for this.
While at it, this commit also fixes up some neighboring lines where
statements were needlessly split over 2 lines to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It makes little sense but still possible to put Hyper-V guests into
suspend-to-idle state. To wake them up two wakeup sources were registered
in the past: hyperv-keyboard and hid-hyperv. However, since
commit eed4d47efe ("ACPI / sleep: Ignore spurious SCI wakeups from
suspend-to-idle") pm_wakeup_event() from these devices is ignored. Switch
to pm_wakeup_hard_event() API as these devices are actually the only
possible way to wakeup Hyper-V guests.
Fixes: eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle)
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
lockdep is much more powerful enforcing the locking rules than code comments,
so let's switch to it.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Motorola/Zebra Symbol DS4308-HD is a handheld USB barcode scanner
which does not have a battery, but reports one anyway that always has
capacity 2.
Let's apply the IGNORE quirk to prevent it from being treated like a
power supply so that userspaces don't get confused that this
accessory is almost out of power and warn the user that they need to charge
their wired barcode scanner.
Reported here: https://bugs.chromium.org/p/chromium/issues/detail?id=804720
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
asus_wmi_evaluate_method() is an empty dummy function when CONFIG_ASUS_WMI
is disabled, or not reachable from a built-in device driver. This leads to
a theoretical evaluation of an uninitialized variable that the compiler
complains about, failing to check that the hardcoded return value makes
this an unreachable code path:
In file included from include/linux/printk.h:336,
from include/linux/kernel.h:14,
from include/linux/list.h:9,
from include/linux/dmi.h:5,
from drivers/hid/hid-asus.c:29:
drivers/hid/hid-asus.c: In function 'asus_input_configured':
include/linux/dynamic_debug.h:135:3: error: 'value' may be used uninitialized in this function [-Werror=maybe-uninitialized]
__dynamic_dev_dbg(&descriptor, dev, fmt, \
^~~~~~~~~~~~~~~~~
drivers/hid/hid-asus.c:359:6: note: 'value' was declared here
u32 value;
^~~~~
With an extra IS_ENABLED() check, the warning goes away.
Fixes: 3b692c55e5 ("HID: asus: only support backlight when it's not driven by WMI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull in a merge commit that brought in 3b692c55e5 ("HID: asus: only
support backlight when it's not driven by WMI") so that fixup could be
applied on top of it.
Move the Dell dcdbas and dell_rbu drivers into platform/drivers/x86 as
they are closely coupled with other drivers in this location.
Improve _init* usage for acerhdf and fix some usage issues with messages
and module parameters.
Simplify asus-wmi by calling ACPI/WMI methods directly, eliminating
workqueue overhead, eliminate double reporting of keyboard backlight.
Fix wake from USB failure on Bay Trail devices (intel_int0002_vgpio).
Notify intel_telemetry users when IPC1 device is not enabled.
Update various drivers with new laptop model IDs.
Update several intel drivers to use SPDX identifers and order headers
alphabetically.
The following is an automated git shortlog grouped by driver:
Add Intel AtomISP2 dummy / power-management driver:
- Add Intel AtomISP2 dummy / power-management driver
lg-laptop:
- Add LG Gram laptop special features driver
HID:
- asus: only support backlight when it's not driven by WMI
MAINTAINERS:
- intel_telemetry: Update maintainers info
- intel_pmc_core: Update MAINTAINERS
- Update maintainer for dcdbas and dell_rbu
- Use my infradead account exclusively for PDx86 work
acerhdf:
- restructure to allow large BIOS table be __initconst
- mark appropriate content with __init prefix
- Add BIOS entry for Gateway LT31 v1.3307
- Remove cut-and-paste trap from instructions
- Enable ability to list supported systems
- clarify modinfo messages for BIOS override
asus-wmi:
- export function for evaluating WMI methods
- Only notify kbd LED hw_change by fn-key pressed
- Simplify the keyboard brightness updating process
firmware:
- dcdbas: include linux/io.h
- dcdbas: Move dcdbas to drivers/platform/x86
- dell_rbu: Move dell_rbu to drivers/platform/x86
- dcdbas: Add support for WSMT ACPI table
- dell_rbu: Make payload memory uncachable
ideapad-laptop:
- Add Y530-15ICH to no_hw_rfkill
- Use __func__ instead of read_ec_cmd in pr_err
intel-hid:
- Convert to use SPDX identifier
intel-ips:
- Convert to use SPDX identifier
intel-rst:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel-smartconnect:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel-wmi-thunderbolt:
- Add dynamic debugging
- Convert to use SPDX identifier
intel_bxtwc_tmu:
- Convert to use SPDX identifier
intel_cht_int33fe:
- Convert to use SPDX identifier
intel_chtdc_ti_pwrbtn:
- Add SPDX identifier
intel_int0002_vgpio:
- Convert to use SPDX identifier
- Implement irq_set_wake
- Enable the driver on Bay Trail platforms
intel_menlow:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_mid_powerbtn:
- Convert to use SPDX identifier
- Remove unnecessary init.h inclusion
- Get rid of custom ICPU() macro
intel_mid_thermal:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_oaktrail:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_pmc:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_punit_ipc:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_scu_ipc:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_telemetry:
- Get rid of custom macro
- report debugfs failure
- Convert to use SPDX identifier
intel_turbo_max_3:
- Convert to use SPDX identifier
- Sort headers alphabetically
mlx-platform:
- Properly use mlxplat_mlxcpld_msn201x_items
touchscreen_dmi:
- Add min-x and min-y settings for various models
- Add info for the Onda V80 Plus v3 tablet
- Add info for the Trekstor Primetab T13B tablet
- Add info for the Trekstor Primebook C11 convertible
tracing:
- Trivia spelling fix containerof() -> container_of()
wmi:
- declare device_type structure as constant
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJb2mDCAAoJEKbMaAwKp364KdkH/Rar8cenw7uFeVzT5o4fGzTn
0Oo1Pnwh+hPgmQwmf8O/mHsa/1Zb9nX4nNLU/ysDUjAAZ9wZLoB57HlImQquPA74
c8lXTz5MVF140WB1f1Ck5PmeonJR2Xve7HTYCoBmGo71jOxHxCgJbp1Giiho0Imd
3NXzzahEnAiy/L5PhqqYTmIfTeAHQ2Fo7GkHCjMnS20FP2fBtvPrc7db03F+FZ4y
QTfbT0oR42NdeW21AbCRGY3P47axB3xDJX4LOYrb4uo4CIzd1yatlHk407NRRyv8
pab6aeJR23FouA/tcvv+T36D3vqRw78e6BWdoyowWOd7CUOgjtSC3lKGzfT6hSY=
=0BDZ
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.20-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
- Move the Dell dcdbas and dell_rbu drivers into platform/drivers/x86
as they are closely coupled with other drivers in this location.
- Improve _init* usage for acerhdf and fix some usage issues with
messages and module parameters.
- Simplify asus-wmi by calling ACPI/WMI methods directly, eliminating
workqueue overhead, eliminate double reporting of keyboard backlight.
- Fix wake from USB failure on Bay Trail devices (intel_int0002_vgpio).
- Notify intel_telemetry users when IPC1 device is not enabled.
- Update various drivers with new laptop model IDs.
- Update several intel drivers to use SPDX identifers and order headers
alphabetically.
* tag 'platform-drivers-x86-v4.20-1' of git://git.infradead.org/linux-platform-drivers-x86: (64 commits)
HID: asus: only support backlight when it's not driven by WMI
platform/x86: asus-wmi: export function for evaluating WMI methods
platform/x86: asus-wmi: Only notify kbd LED hw_change by fn-key pressed
platform/x86: wmi: declare device_type structure as constant
platform/x86: ideapad: Add Y530-15ICH to no_hw_rfkill
platform/x86: Add Intel AtomISP2 dummy / power-management driver
platform/x86: touchscreen_dmi: Add min-x and min-y settings for various models
platform/x86: touchscreen_dmi: Add info for the Onda V80 Plus v3 tablet
platform/x86: touchscreen_dmi: Add info for the Trekstor Primetab T13B tablet
platform/x86: intel_telemetry: Get rid of custom macro
platform/x86: intel_telemetry: report debugfs failure
MAINTAINERS: intel_telemetry: Update maintainers info
platform/x86: Add LG Gram laptop special features driver
platform/x86: asus-wmi: Simplify the keyboard brightness updating process
platform/x86: touchscreen_dmi: Add info for the Trekstor Primebook C11 convertible
platform/x86: mlx-platform: Properly use mlxplat_mlxcpld_msn201x_items
MAINTAINERS: intel_pmc_core: Update MAINTAINERS
firmware: dcdbas: include linux/io.h
platform/x86: intel-wmi-thunderbolt: Add dynamic debugging
platform/x86: intel-wmi-thunderbolt: Convert to use SPDX identifier
...
The Asus GL502VSK has the same 0B05:1837 keyboard as we've seen in
several Republic of Gamers laptops.
However, in this model, the keybard backlight control exposed by hid-asus
has no effect on the keyboard backlight. Instead, the keyboard
backlight is correctly driven by asus-wmi.
With two keyboard backlight devices available (and only the acer-wmi
one working), GNOME is picking the wrong one to drive in the UI.
Avoid this problem by not creating the backlight interface when we
detect a WMI-driven keyboard backlight.
We have also tested Asus GL702VMK which does have the hid-asus
backlight present, and it still works fine with this patch (WMI method
call returns UNSUPPORTED_METHOD).
A direct "depends on ASUS_WMI" is intentionally avoided so that HID_ASUS
users who have ASUS_WMI=n will not quietly lose their HID_ASUS driver on
a kernel upgrade.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This device uses the SIPODEV SP1064 touchpad, which does not
supply descriptors, so it has to be added to the override list.
Reported-by: Tim Aldridge <taldridge@mac.com>
Signed-off-by: Julian Sax <jsbc@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
-----BEGIN PGP SIGNATURE-----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=Cc6D
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new dvb frontend driver: lnbh29
- new sensor drivers: imx319 and imx 355
- some old soc_camera driver renames to avoid conflict with new
drivers
- new i.MX Pixel Pipeline (PXP) mem-to-mem platform driver
- a new V4L2 frontend for the FWHT codec
- several other improvements, bug fixes, code cleanups, etc
* tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (289 commits)
media: rename soc_camera I2C drivers
media: cec: forgot to cancel delayed work
media: vivid: Support 480p for webcam capture
media: v4l2-tpg: fix kernel oops when enabling HFLIP and OSD
media: vivid: Add 16-bit bayer to format list
media: v4l2-tpg-core: Add 16-bit bayer
media: pvrusb2: replace `printk` with `pr_*`
media: venus: vdec: fix decoded data size
media: cx231xx: fix potential sign-extension overflow on large shift
media: dt-bindings: media: rcar_vin: add device tree support for r8a7744
media: isif: fix a NULL pointer dereference bug
media: exynos4-is: make const array config_ids static
media: cx23885: make const array addr_list static
media: ivtv: make const array addr_list static
media: bttv-input: make const array addr_list static
media: cx18: Don't check for address of video_dev
media: dw9807-vcm: Fix probe error handling
media: dw9714: Remove useless error message
media: dw9714: Fix error handling in probe function
media: cec: name for RC passthrough device does not need 'RC for'
...
Commit 1ff2e1a44e ("HID: input: Create a utility class for counting
scroll events") created the helper function
hid_scroll_counter_handle_scroll()
to handle high-res scroll events and also expose them as regular wheel
events.
But the resulting algorithm was unstable, and causes scrolling to be
very unreliable. When you hit the half-way mark of the highres
multiplier, small highres movements will incorrectly translate into big
traditional wheel movements, causing odd jitters.
Simplify the code and make the output stable.
NOTE! I'm pretty sure this will need further tweaking. But this at
least turns a unusable mouse wheel on my Logitech MX Anywhere 2S into
a usable one.
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Harry Cutts <hcutts@chromium.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
.. even when that "default y" is hidden syntactically as a
default !EXPERT
it's wrong.
The only reason something should be 'default y' is if it used to be
built-in, and it was made configurable, and the 'default y' is just
retaining the status quo.
Altheratively, the hardware for the driver has become _so_ common that
it really makes sense for everybody to build it. Finally, one possible
reason for 'default y' is because the option is not enabling any new
code at all, but is just enabling other options (the networking people
do this for vendor options, for example, so that you can disable whole
vendors at a time).
Clearly, none of these cases hold for the BigBen Interactive Kids'
gamepad, and HID_BIGBEN_FF should thus most definitely not default
to on for everybody.
Cc: Hanno Zulla <kontakt@hanno.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9ee3e06610 ("HID: i2c-hid: override HID descriptors for certain
devices") added a new dmi_system_id quirk table to override certain HID
report descriptors for some systems that lack them.
But the table wasn't properly terminated, causing the dmi matching to
walk off into la-la-land, and starting to treat random data as dmi
descriptor pointers, causing boot-time oopses if you were at all
unlucky.
Terminate the array.
We really should have some way to just statically check that arrays that
should be terminated by an empty entry actually are so. But the HID
people really should have caught this themselves, rather than have me
deal with an oops during the merge window. Tssk, tssk.
Cc: Julian Sax <jsbc@gmx.de>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If userspace only reads the trackstick node, and no one is listening to
the touchpad nor the hidraw node then, the device is not powered on.
Add open/close callbacks to allow users to disable the touchpad in Gnome
while keeping the trackstick active.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1559632
Link: https://gitlab.gnome.org/GNOME/mutter/issues/128
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 67ddbb3e65.
67ddbb3e65 ("HID: add NOGET quirk for Eaton Ellipse MAX UPS") was reported
by Laurent Bigonville. It turns out that a later model Laurent got
doesn't need the quirk after all.
My take is that Eaton upgraded their firmwares, so we don't need it
anymore.
The old model was from 2012, so better make sure the new line works
properly by removing the quirk. This allows upower to actually fetch
the current data.
Reported-by: Laurent Bigonville <bigon@bigon.be>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rushikesh S Kadam