buf_prepare callback is called for every queued buffer. This is
an overkill. Call it at buf_setup, as this should be enough.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are two problems at the comment:
- it is badly idented;
- its comment doesn't mean anything.
Fix it.
Requested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Analog video inputs are the tuner, plus composite, svideo, etc,
e. g. the input pat should actually be like:
___________
TUNER --------> | |
| |
SVIDEO .......> | cx25840 |
| |
COMPOSITE1 ...> |_________|
(in the above, dashes represent the enabled link, and periods
represent the disabled ones)
In other words, if we want to properly represent the pipeline,
it should be possible to see via the media controller if the tuner
is being used as an image source, or if the source is something else.
I didn't map those other inputs here yet, due to a few things:
- The extra inputs would require subdevs that won't be controlled
- I was in doubt about the best way for doing that
- That would likely require some extra setup for cx25840 caller
drivers, in order to represent what of the possible internal
inputs are actually used on each specific board
Actually, at least for now, I was unable to see much benefit
on adding such map now, so let's just document it, as this could
be added later on, as needed.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prefix all DVB media controller entities with "dvb-" and use dash
instead of underline at the names.
Requested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_usb_probe’:
drivers/media/usb/cx231xx/cx231xx-cards.c:1589:15: error: ‘struct v4l2_device’ has no member named ‘mdev’
dev->v4l2_dev.mdev = dev->media_dev;
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1589:26: error: ‘struct cx231xx’ has no member named ‘media_dev’
dev->v4l2_dev.mdev = dev->media_dev;
^
scripts/Makefile.build:257: recipe for target 'drivers/media/usb/cx231xx/cx231xx-cards.o' failed
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
if CONFIG_MEDIA_CONTROLLER_DVB is not selected, it is now
producing this warning:
drivers/media/dvb-core/dvb_frontend.c: In function ‘dvb_frontend_thread’:
drivers/media/dvb-core/dvb_frontend.c:695:6: warning: unused variable ‘ret’ [-Wunused-variable]
int ret;
^
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The logic there tries to start the media entity even if it
doesn't exist, causing this bug:
[ 314.356162] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
[ 314.356202] IP: [<ffffffffa02ef74c>] media_entity_pipeline_start+0x1c/0x390 [media]
Reported-by: Gert-Jan van der Stroom <gjstroom@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU6pFJAAoJEHm+PkMAQRiG2OwH/24nDK+l9zkaRs0xJsVh+qiW
8A2N1od0ickz43iMk48jfeWGkFOkd4izyvan/daJshJOE1Y5lCdSs7jq/OXVOv9L
G0+KQUoC5NL0hqYKn1XJPFluNQ1yqMvrDwQt99grDGzruNGBbwHuBhAQmgzpj1nU
do8KrGjr7ft1Rzm4mOAdET/ExWiF+mRSJSxxOv598HbsIRdM5wgn0hHjPlqDxmLN
KH4r3YYEm0cHyjf4Krse0+YdhqdamRGJlmYxJgEsYNwCoMwkmHlLTc71diseUhrg
r/VYIYQvpAA6Yvgw8rJ0N5gk/sJJig+WyyPhfQuc2bD5sbL9eO7mPnz2UP7z7ss=
=vXB6
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc1' into patchwork
Linux 34.0-rc1
* tag 'v4.0-rc1': (8947 commits)
Linux 4.0-rc1
autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
procfs: fix race between symlink removals and traversals
debugfs: leave freeing a symlink body until inode eviction
Documentation/filesystems/Locking: ->get_sb() is long gone
trylock_super(): replacement for grab_super_passive()
fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry)
SELinux: Use d_is_positive() rather than testing dentry->d_inode
Smack: Use d_is_positive() rather than testing dentry->d_inode
TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR()
Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode
Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb
VFS: Split DCACHE_FILE_TYPE into regular and special types
VFS: Add a fallthrough flag for marking virtual dentries
VFS: Add a whiteout dentry type
VFS: Introduce inode-getting helpers for layered/unioned fs environments
kernel: make READ_ONCE() valid on const arguments
blk-throttle: check stats_cpu before reading it from sysfs
...
Decrementing the reference count of the previous endpoint node allows to
use the of_graph_get_next_endpoint function in a for_each_... style macro.
All current users of this function that pass a non-NULL prev parameter
(that is, soc_camera and imx-drm) are changed to not decrement the passed
prev argument's refcount themselves.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While the DVB thread is running, the media pipeline should be
streaming. This should prevent any attempt of using the analog
TV while digital TV is working, and vice-versa.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the dvb frontend thread starts, the tuner should be switched
to the frontend. Add a code that ensures that this will happen,
using the media controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For now, let's keep the DVB-specific media controller links enabled
by default. On most devices, this is fixed anyway, so no big issue.
Ok, the demux actually have dynamic links based on the filters, but
we don't represent them yet, as the media controller currently lacks
the capability of dynamically create/delete entities.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
cx231xx is simple with regards to DVB: all boards have just one
DVB adapter. So, we can use the default DVB helper function to
create the DVB media graph.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to create a DVB graph, linking the several DVB devnodes.
Add such function. Please notice that this helper function
doesn't take into account devices with multiple DVB adapters
and frontends.
For devices with multiple adapters, they should either create two
different media controller instances or to improve this function
to take the adapter ID into account.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While on some devices the tuner is bound inside the frontend,
other devices use a separate subdevice for it.
So, in order to be more generic, better to map it with two
pads.
That will allows to use the media controller to lock the tuner
between the DVB and the V4L2 sub-drivers, on hybrid devices.
While here, change the logic to use pad 0 as sink for devices
with both sink and source pads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that we have entities and pads, let's create media links
between them, for analog setup.
We may not have all the links for digital yet, as the dvb extention
may not be loaded yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of keeping the media controller entity not initialized,
fill it and create the pads for cx25840.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Properly initialize tuner core subdev at the media controller.
That requires a new subtype at the media controller API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We want to represent the links between the several DVB devnodes,
so let's create PADs for them.
The DVB net devnode is a different matter, as it is not related
to the media stream, but with network. So, at least for now, let's
not add any pad for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the dvb core network support aware of the media controller and
register the corresponding devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the dvb core CA support aware of the media controller and
register the corresponding devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the dvb core demux support aware of the media controller and
register the corresponding devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that the dvb core is capable of registering devices via the
media controller, add support for the DVB frontend devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let's add media controller support for this driver and register it
for both V4L and DVB.
The media controller on this driver is not mandatory, as it can fully
work without it. So, if the media controller register fails, just print
an error message, but proceed with device registering.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide a way to register media controller device nodes
at the DVB core.
Please notice that the dvbdev callers also require changes
for the devices to be registered via the media controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The previous provision for DVB media controller support were to
define an ID (likely meaning the adapter number) for the DVB
devnodes.
This is just plain wrong. Just like V4L, DVB devices (and any other
device node)) are uniquely identified via a (major, minor) tuple.
This is enough to uniquely identify a devnode, no matter what
API it implements.
So, before we go too far, let's mark the old v4l, fb, dvb and alsa
"devnode" info as deprecated, and just call it as "dev".
We can latter add fields specific to each API if needed.
As we don't want to break compilation on already existing apps,
let's just keep the old definitions as-is, adding a note that
those are deprecated at media-entity.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This allows those get_user_pages calls to pass FAULT_FLAG_ALLOW_RETRY to
the page fault in order to release the mmap_sem during the I/O.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Peter Feiner <pfeiner@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported by Peter Kovar, there's a potential risk of a division by
zero on calls to jpeg_set_qual() when quality is zero.
As quality can't be 0 or lower than that, add an extra clause to cover
this special case.
Signed-off-by: Luis de Bethencourt <luis.bg@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the generic facility instead of a home-grown one.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert dprintk to netdev_dbg where appropriate.
Remove dvb_net_debug module_param.
Remove __func__ from output as that can be added by dynamic_debug.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No need for more macros, so remove them and use the kernel extension.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of implement its own logic, use the already-defined one.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch is based on Antti's silabs branch.
Add support for 1.7 MHz bandwidth. Supported in all versions of Si2168 according to short data sheets.
[mchehab@osg.samsung.com: Fix CodingStyle]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch should is based on Antti's silabs branch.
According to dvb-frontend.h set_frontend may be called with bandwidth_hz set to 0 if automatic bandwidth is required. Si2168 does not support automatic bandwidth and does not declare FE_CAN_BANDWIDTH_AUTO in caps.
This patch will change the behaviour in a way that EINVAL is returned if bandwidth_hz is 0.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We have to check pointer for NULL and then dereference it.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
symbol-rate report was wrongly removed off by the commit:906aaf5a .
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This allows calling the original functions providing the streaming is off.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create dm04_read_status to check lock through either interrupt values
or directly by the call back.
When the device is not streaming the frontends original call back is
used. When streaming has started it turns off I2C messaging by
setting st->i2c_talk_onoff to zero. I2C can only be turn on again
by one of the other allowed frontend calls.
All old code is removed from lme2510_msg and this function only needs
to set st->i2c_talk_onoff to 1.
The lock status is saved and when the frondend is locked is maintained
by lme2510_int_response who will now just kill the lock.
The call back for rs2000 tuner is nologer required.
All frontend types have been tested.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create call backs dm04_read_signal_strength, dm04_read_snr and
move dm04_read_ber and dm04_read_ucblocks for all frontends
Removing the I2C filtering from lme2510_msg and the old rs2000 callbacks.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A quirk of some older firmwares that report endpoint pipe type as PIPE_BULK
but the endpoint otheriwse functions as interrupt.
Check if usb_endpoint_type is USB_ENDPOINT_XFER_BULK and set as usb_rcvbulkpipe.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ocassionally the device fails to report back an interrupt urb status which
results in false no lock trigger on the RS2000 demodulator.
Increase time from 60 msecs to 200 msecs.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
X-Patchwork-Delegate: m.chehab@samsung.com
Fix the following smatch warning:
drivers/media/pci/cx88//cx88-dvb.c:1508 dvb_register() warn: if statement not indented
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As complained by smatch:
drivers/media/usb/dvb-usb-v2/rtl28xxu.c:1159 rtl2832u_tuner_attach() info: 'pdata' is not actually initialized (unreached code).
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/rtl2832.c:157:5: warning: no previous prototype for ‘rtl2832_bulk_write’ [-Wmissing-prototypes]
int rtl2832_bulk_write(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2832.c:169:5: warning: no previous prototype for ‘rtl2832_update_bits’ [-Wmissing-prototypes]
int rtl2832_update_bits(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2832.c:181:5: warning: no previous prototype for ‘rtl2832_bulk_read’ [-Wmissing-prototypes]
int rtl2832_bulk_read(struct i2c_client *client, unsigned int reg, void *val,
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/rtl2830.c:21:5: warning: no previous prototype for ‘rtl2830_bulk_write’ [-Wmissing-prototypes]
int rtl2830_bulk_write(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2830.c:33:5: warning: no previous prototype for ‘rtl2830_update_bits’ [-Wmissing-prototypes]
int rtl2830_update_bits(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2830.c:45:5: warning: no previous prototype for ‘rtl2830_bulk_read’ [-Wmissing-prototypes]
int rtl2830_bulk_read(struct i2c_client *client, unsigned int reg, void *val,
^
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use rtl28xxu_ prefix for all register access routine names.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As all the callbacks are already same we could merge device
properties struct too and save space.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Merge all chip type specific prefixed (rtl2831u_ and rtl2832u_)
callback to top level callback prefixed as rtl28xxu_.
rtl2831u_foo() => rtl28xxu_foo()
rtl2832u_foo() => rtl28xxu_foo()
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Detect automatically whether chip is old RTL2831U or newer
RTL2832U/RTL2832P. Detection is based I2C command that is found only
from newer RTL2832U models.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Buffer needed for USB control message is small so move it to state
and get rid of alloc/free used for each control message.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pass correct device pointer to dev_* logging in order to print
module name and bus id correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I prefer dev over priv and I want keep all my drivers in line with
that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There was 2 muxed I2C adapters, one for demod tuner bus and one for
internal use. Idea of internal I2C adapter was to force I2C repeater
close when demod access its registers. Driver has also delayed work
queue based method to close I2C repeater.
After regmap conversion internal I2C adapter based repeater close
left unused - only work queue method was in use. We could not use
internal mux adapter method with regmap as it makes recursive regmap
call, which causes deadlock as regmap has own locking. Due to that
remove whole method totally.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We are consumer of DVB frontend provided by rtl28xxu module. Due to
that we must use refcount to ensure none could remove rtl28xxu when
we are alive (or when we are streaming, if more fine-grained
refcounting is wanted).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver, rtl28xxu, offers frontend service for rtl2832_sdr
module, thus we are producer and rtl2832_sdr module is consumer.
Due to that, reference counting should be done in way rtl2832_sdr
takes refrence to rtl28xxu. Remove wrong refcount.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Logic is so simple that there is no idea to separate tuner selection to
own function, instead do it in a callback and get rid of one function.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
DVB FE callback functionality went broken after I moved tuners to
demod muxed I2C adapter. That happens because driver state was
carried by I2C adapter and when mux is used there is one adapter
more in a chain.
USB adapter <-> I2C adapter <-> muxed I2C adapter
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Put demod to soft reset in order to save power when sleep. That drops
power usage ~30mA @5V on USB dongle I tested. In real life it does
not matter much as USB IF powers off demod too, but now it is done
twice - demod and USB IF.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I have implemented tons of things for that driver, more than anyone
else, so lets claim copyright and module authorship.
Cc: Thomas Mair <thomas.mair86@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove all the stuff that is not needed anymore. Rename variable.
Remove extra new lines.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pass correct device, platform device, for logging system in order
to format printouts correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both mn88472 and mn88473 slave demods are connected to master I2C
bus, not the bus behind master demod I2C gate like tuners. Use
correct bus.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
That SDR driver module was abusing DVB frontend SEC (satellite
equipment controller) device and due to that it was also using
legacy DVB binding. Platform bus is pseudo-bus provided by kernel
driver model and it fits cases like that, where any other busses
are not suitable.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
'dev' sounds better than 's' for such variable.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide register read and write callbacks for SDR module.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Chips uses 8-bit register addresses with 5 pages. Extend register
address by using register page as a first byte of address, defining
virtual register addresses. That is common method of handling
register pages and regmap also uses it. Remove page + address
conversion glue which was there for regmap.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to do software reset on init() as it is done a bit
later on end of set_frontend(). Software reset usually means
restarting (resetting to starting point) chip internal state machine
(FSM). Naturally it is done after all parameters are programmed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Enable regmap register cache in order to reduce IO.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
RTL2832 demod integrated into RTL2832U has PID filter. PID filtering
is provided by rtl2832 demod driver. Add support for it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Demod lock flags are derived from demod state machine states. States
are running from 1 to 11, where highest state 11 means demod is
fully locked and streaming. Naturally smaller state numbers means
there is some partial locks.
Define now state 10 as missing synch and lock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We don't need it anymore as all users are using muxed I2C adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tuners are connected to demod I2C adapter. Use that muxed adapter
for each tuner. That allows us to get rid of hackish FE gate control
solution.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Estimate signal strength from IF digital AGC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use platform data configuration for rtl2832 demod driver. Old
configuration are still left as it is used for rtl2832_sdr driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move all needed configuration values to platform data structure
and remove old configuration code where possible.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename it device state variable to dev. Both priv and dev are very
common terms for such variable in kernel, but I like use dev in
order to keep drivers consistent.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Exported resources are not needed anymore as all users are using
callbacks carried via platform data. Due to that we will remove
those.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch demod resource use from exported symbols to callbacks its
provides.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add callback for all of those functions which are currently
exported using EXPORT_SYMBOL. That allows us convert every user to
callbacks and eventually all exported symbols could be removed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Own I2C locking is needed due to two special reasons:
1) Chips uses multiple register pages/banks on single I2C slave.
Page is changed via I2C register access.
2) Chip offers muxed/gated I2C adapter for tuner. Gate/mux is
controlled by I2C register access.
Due to these reasons, I2C locking did not fit very well.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
RTL2830 demod integrated to RTL2831U has PID filter. PID filtering
is provided by rtl2830 demod driver. Add support for it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Trivial changes proposed by checkpatch.pl and some more.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove internal config and use configuration values directly from
the platform data.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pass correct device for dev_foo() logging in order to print logs
correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As a I2C driver struct i2c_client is top level structure representing
the driver. Use it as parameter to carry all needed information for
each function in order to simplify things.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use name 'dev' for device state instance as it is more common and
also one letter shorter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove legacy DVB binding as all users are using I2C binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rtl2830 driver supports now I2C model too. Start using it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert driver to kernel I2C model. Old DVB proprietary model is
still left there also.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Top level pointer on USB probe is struct usb_interface *. Add that
pointer to struct dvb_usb_device that drivers could use it, for
dev_* logging and more.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Although IRQ_HANDLED is "safe" value to return,
it is better to let the kernel know whether the driver handle the interrupt or not.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/platform/am437x/am437x-vpfe.c:2767:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mmp ccic driver expects a platform_data structure that does not exist
in the mainline kernel and presumably was changed in a kernel fork, which
leads to build errors now:
media/platform/marvell-ccic/mmp-driver.c: In function 'mmpcam_calc_dphy':
media/platform/marvell-ccic/mmp-driver.c:252:15: error: 'struct mmp_camera_platform_data' has no member named 'dphy3_algo'
switch (pdata->dphy3_algo) {
^
media/platform/marvell-ccic/mmp-driver.c:253:7: error: 'DPHY3_ALGO_PXA910' undeclared (first use in this function)
case DPHY3_ALGO_PXA910:
^
media/platform/marvell-ccic/mmp-driver.c:253:7: note: each undeclared identifier is reported only once for each function it appears in
media/platform/marvell-ccic/mmp-driver.c:257:8: error: 'struct mmp_camera_platform_data' has no member named 'dphy'
This marks the driver as 'BROKEN' but keeps the code around.
Alternatively it could be removed entirely.
Fixes: 05fed81625 ("[media] marvell-ccic: add MIPI support for marvell-ccic driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Libin Yang <lbyang@marvell.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1: Simplify the vpe mem-to-mem driver by using the m2m ioctl
and vb2 helpers.
2: Align and arranged the v4l2_ioctl_ops.
3: Fixes a typo.
4: Use of_match_ptr() instead of explicitly defining the macro
to NULL in case CONFIG_OF is not defined.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
X-Patchwork-Delegate: m.chehab@samsung.com
As shown at the code, upd_demod_gain_period is used to write
to two 16-bit registers:
dib8000_write_word(state, 1946, upd_demod_gain_period & 0xFFFF);
dib8000_write_word(state, 1947, reg | (1<<14) | ((upd_demod_gain_period >> 16) & 0xFF));
So, it should be declared as u32.
This fixes the following smatch warning:
drivers/media/dvb-frontends/dib8000.c:1282 dib8000_agc_startup() warn: right shifting more than type allows
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/pci/cx23885/cx23885-dvb.c:2080 dvb_register() Function too hairy. Giving up.
This is indeed a too complex function, with lots of stuff inside.
Breaking this into two functions makes it a little bit less hairy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert au0828 to use videobuf2. Tested with NTSC.
Tested video and vbi devices with xawtv, tvtime,
and vlc. Ran v4l2-compliance to ensure there are
no failures.
Video compliance test results summary:
Total: 75, Succeeded: 75, Failed: 0, Warnings: 18
Vbi compliance test results summary:
Total: 75, Succeeded: 75, Failed: 0, Warnings: 0
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
au0828 picked up UNSET from videobuf-core.h and fails to compile
if videobuf-core.h isn't included. Change it to use -1U instead
to fix the problem.
drivers/media/usb/au0828/au0828-cards.c:47:17: error: ‘UNSET’ undeclared here (not in a function)
.tuner_type = UNSET,
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
au0828_analog_register() frees au0828_dev when it fails to
locate isoc endpoint. au0828_usb_probe() continues with dvb
and rc probe and registration assuming dev is still valid.
When au0828_analog_register() fails to locate isoc endpoint,
it should return without free'ing au0828_dev. Otherwise, the
probe will fail as dev is null when au0828_dvb_register() is
called.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In fast switch mode the adv7180 (and similar) can lock onto a new signal
faster when switching between different inputs. As a downside though it is
no longer able to auto-detect the incoming format.
The fast switch mode is exposed as a boolean v4l control that allows
userspace applications to either enable or disable fast switch mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some of the devices supported by this driver have a interlaced-to-
progressive converter which can optionally be enabled. This patch adds
support for enabling and disabling the I2P converter on such devices.
I2P mode can be enabled by selecting V4L2_FIELD_NONE instead of
V4L2_FIELD_INTERLACED for the format.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7280-m/adv2781-m/adv7281-ma/adv7282-m
devices to the adv7180 driver. They are very similar to the
adv7280/adv7281/adv7282 but instead of parallel video out they feature a
MIPI CSI2 transmitter.
The CSI2 transmitter is configured via a separate I2C address, so we need to
register a dummy device for it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7280/adv7281/adv7282 devices to the
adv7180 driver. They are very similar to the adv7182, the main difference
from the drivers point of view are some different tuning constants for
improved video performance.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7182 to the adv7180 driver. The adv7182
is similar to the adv7180, the main difference from the driver's point of
view is how the video input and how the input format are selected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7180 is part of a larger family of device, which have all a very
similar register map layout. This patch prepares the adv7180 driver for
support for multiple different devices. For now the only difference we care
about is the number of input channel configurations. Also the way the input
format is configured slightly differs between some devices.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We have basically the same code to set the video standard in init_device()
and adv7180_s_std(). Factor this out into a common helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add media controller support to the adv7180 driver by registering a media
entity instance for it as well as implementing pad ops for configuring the
format.
As there currently don't seem to be any users of the video ops format
operations those are removed as well in this patch.
Also set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so it is
possible to create a subdevice device node.
Since the driver now depends on VIDEO_V4L2_SUBDEV_API all drivers which
select the driver need to depend on that symbol as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reset the device when initializing it so it is in a good known state and the
assumed register settings matches the actual register settings.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ad7180 has multiple register pages which can be switched between by
writing to a register. Currently the driver manually switches between pages
whenever a register outside of the default register map is accessed and
switches back after it has been accessed. This is a bit tedious and also
potential source for bugs.
This patch adds two helper functions that take care of switching between
pages and reading/writing the register. The register numbers for registers
are updated to encode both the page (in the upper 8-bits) and the register
(in the lower 8-bits) numbers.
Having multiple pages means that a register access is not a single atomic
i2c_smbus_write_byte_data() or i2c_smbus_read_byte_data() call and we need
to make sure that concurrent register access does not race against each
other.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Consistently prefix register defines with ADV7180_REG. Also remove the "ADI"
from register names, the ADV7180 prefix should provide enough of a namespace
separation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Most IRQ controllers support different types of interrupts. The adv7180
generates falling edge interrupts, so make sure to pass IRQF_TRIGGER_FALLING
to request_threaded_irq() so the IRQ controller is configured for the
correct mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently the IRQ is requested from within the init_device() function. This
function is not only called during device probe, but also during resume
causing the driver to try to request the IRQ again. Move requesting the IRQ
from init_device() to the probe function to make sure that it is only
requested once.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The davinci media drivers use videobuf2, which they enable through
a 'select' statement. If one of these drivers is built-in, but
the v4l2 core is a loadable modules, we end up with a link
error:
drivers/built-in.o: In function `vb2_fop_mmap':
:(.text+0x113e84): undefined reference to `video_devdata'
drivers/built-in.o: In function `vb2_ioctl_create_bufs':
:(.text+0x114710): undefined reference to `video_devdata'
drivers/built-in.o: In function `vb2_ioctl_reqbufs':
:(.text+0x114ed8): undefined reference to `video_devdata'
drivers/built-in.o: In function `vb2_ioctl_querybuf':
:(.text+0x115530): undefined reference to `video_devdata'
To solve this, we need to add a dependency on VIDEO_V4L2,
which enforces that the davinci drivers themselves can only
be loadable modules if V4L2 is not built-in, and they do
not cause the videobuf2 code to be built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Keep the colorspace and encoding names consistent with what is
used elsewhere (primarily the utilities in v4l-utils.git).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The USB and MMC front-ends to the siano driver both only make
sense when combined with the SMS_SIANO_MDTV driver. That driver
already requires RC_CORE to not be a module, so we also need
to add that dependency here.
drivers/built-in.o: In function `smssdio_remove':
:(.text+0x155bd8): undefined reference to `smscore_putbuffer'
:(.text+0x155bdc): undefined reference to `smscore_unregister_device'
drivers/built-in.o: In function `smssdio_interrupt':
:(.text+0x155e4c): undefined reference to `smsendian_handle_rx_message'
:(.text+0x155e50): undefined reference to `smscore_onresponse'
:(.text+0x155e54): undefined reference to `smscore_getbuffer'
:(.text+0x155e58): undefined reference to `smscore_putbuffer'
drivers/built-in.o: In function `smssdio_sendrequest':
:(.text+0x155f20): undefined reference to `smsendian_handle_tx_message'
drivers/built-in.o: In function `smssdio_probe':
:(.text+0x15610c): undefined reference to `sms_get_board'
:(.text+0x156114): undefined reference to `smscore_register_device'
:(.text+0x156118): undefined reference to `smscore_set_board_id'
:(.text+0x156128): undefined reference to `smscore_unregister_device'
:(.text+0x156140): undefined reference to `smscore_start_device'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Large udelay values are not allowed on the ARM architecture
and result in a build error like
ERROR: "__bad_udelay" [drivers/media/radio/radio-aimslab.ko] undefined!
This changes the aimslab radio driver to use an equivalent mdelay
statement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The timberdale media driver requires the use of the respective
dma engine driver, but that may not be enabled, causing a
Kconfig warning:
warning: (VIDEO_TIMBERDALE) selects TIMB_DMA which has unmet direct dependencies (DMADEVICES && MFD_TIMBERDALE)
This fixes the dependency by removing the inappropriate 'select'
statement and replacing it with a direct dependency on the
drivers that provide the services this needs.
Fixes: 7155043c2d ("[media] enable COMPILE_TEST for media drivers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is only an API consolidation and should make things more readable
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
changeset 5eeb301482 added a fixup at the error check
code. However, it introduced a new error:
drivers/media/usb/cx231xx/cx231xx-cards.c:1586 cx231xx_usb_probe() error: we previously assumed 'dev' could be null (see line 1430)
This happens when dev = kmalloc() fails. So, instead of relying
on it to succeed, just change the parameter of clear_bit() from
'dev->devno' to 'nr'.
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit b7085c0864 ("cx231xx: convert from pr_foo to dev_foo")
moves usb_get_dev(interface_to_usbdev(interface)) to the beginning
of cx231xx_usb_probe() to use udev->dev in dev_err(),
but it does not make sure usbdev is put on all failure paths.
Later dev_err(udev->dev) was replaced by dev_err(d).
So the patch moves usb_get_dev() below (before the first use)
and fixes another failure path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This commit moves the "buffer in use" logic from the .buf_cleanup
handler into .stop_streaming, based on advice that this is its
proper logical home.
By ensuring the list of pointers in priv->queue_buf[] is managed
as soon as possible, we avoid warnings concerning buffers in ACTIVE
state when the system cleans up after streaming stops. This fixes a
problem with modification of buffers after their content has been
cleared for passing to userspace.
After the refactoring, the buf_init and buf_cleanup functions were
found to contain only initialisation/release steps as are carried out
elsewhere if omitted; these functions and references were removed.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The code that tests that capture from a stream has stopped is
presently insufficient and the potential for a race condition
exists where frame capture may generate an interrupt between
requesting the capture process halt and freeing buffers.
This patch refactors code out of rcar_vin_videobuf_release() and
into rcar_vin_wait_stop_streaming(), and ensures there are calls
in places where we need to know that capturing has finished.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reuse the v4l2 size definitions from v4l2-image-sizes.h.
So we can remove the rudundent definitions from ov2640.c.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A hunk, removing this code has been lost between versions 6 and 7 of
patch "soc-camera: add V4L2-async support." The code is harmless, but
redundant.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that the bitstream buffer is only allocated for the BIT decoder
case, we can use bitstream.size to check for bitstream ringbuffer
operation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The BIT encoder does not use a per-context bitstream ringbuffer as it encodes
directly into the videobuf2 capture queue's buffers. Avoid allocation of the
bitstream ringbuffer for encoder contexts.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In preparation for CODA9 JPEG support, allow contexts that
control hardware units directly, without the BIT processor.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure the buffer_mutex lock is taken in coda_bit_release
while coda_free_framebuffers and coda_free_context_buffers
are called.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In preparation for CODA9 JPEG support, which doesn't have to call
SEQ_END on the BIT processor.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since we have to copy from input buffers into the bitstream ringbuffer
with the CPU, there is no need for contiguous DMA buffers on the decoder
input side.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On i.MX6, two subsampling ping-pong buffers are used for motion estimation and
deblocking They should not be counted as framebuffers, or they will be also used
to store reconstructed frames, causing visible artifacts in P-frames.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch queues seq_end_work and flushes the queue during stop_streaming
and clears the ctx->initialized flag. This allows to start streaming again
after stopping streaming without releasing the context.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The isequence counter is never used, qsequence counts the buffers queued into
the bit decoder bitstream ringbuffer. It needs to be reset in stop_streaming.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Compare rounded up width to fit into bytesperline.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To make sure a set RET_DEC_PIC_SUCCESS flag is not a leftover from
a previous successful run, clear it in prepare_decode.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Properly zero the structure on the stack before using it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
v4l2-compliance complains about invalid colorspace settings being accepted
on the output side. This patch only allows REC709 and JPEG.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Clarify whether job_ready returns false because the context is on hold, waiting
for new input buffers, whether there are not enough input buffers to fill two
into the bitstream, or whether there is not enough data in the bitstream buffer
for the bitstream reader hardware to read a whole frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If userspace doesn't properly separate the bitstream input into
individual frames (which may happen for example on slightly
corrupted streams) the CODA hardware may decode more frames
than we expect. We already log an error in this case, but it's
also necessary to adjust the sequence offset. Otherwise we
spam the log with a sequence number mismatch on every frame
frame after the unexpected one.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Handle an empty buffer metadata list without crashing. This can happen
if the decoder is fed a broken stream, or multiple compressed frames in
a single queued buffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Do not remove the per-context debugfs directory before the
per-buffer debugfs entries contained therein.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch fixes the ENC_SEQ_RC_PARA initial delay and bitrate masks.
These bit fields are 15 bit wide, not 7 bit.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The decoder should handle V4L2_DEC_CMD_STOP to trigger drain,
but it currently expecting V4L2_ENC_CMD_STOP.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The MFC driver has two controls, DISPLAY_DELAY and DISPLAY_DELAY_ENABLE
that allow forcing the decoder to return a decoded frame sooner
regardless of the order. The added support for firmware version 6 and
higher was not taking into account the DISPLAY_DELAY_ENABLE boolean.
Instead it had a comment stating that DISPLAY_DELAY should be set to a
negative value to disable it. This is not possible since the control
range is from 0 to 65535. This feature was also supposed to be disabled
by default in order to produce frames in display order.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename firmware variable from fw_file to fw_name and change its
type from u8 to const char as request_firmware() input is.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Print chip version once using log level into when init() is called.
Remove cold/warm state printing as those are not very useful.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Firmware version could be printed similarly than si2168 driver does.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use own goto label for error case mem free is needed, even kfree could
be called with NULL. I think it is better to have it, even not required.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- Rename ID table.
- Remove magic numbers from ID table driver data field.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename firmare download error path goto label. Remove firmware NULL
set as NULL value is not needed anymore, due to recent change which
started using goto labels for firmware error handling.
Cc: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Carry struct i2c_client pointer in tuner_priv. This driver is I2C driver,
which is represented as a struct i2c_client, so better to carry this top
level structure for each routine in order to unify things.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove if () from firmware command error path as there should not be
any error prone conditional logic there. Use goto labels instead.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
'dev' is likely most common name in kernel for structure containing
device state instance, so rename it in order to keep things
consistent.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename firmware variable from fw_file to fw_name and change its type
from u8 to const char as request_firmware() input defines.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Print chip version once using log level into when init() is called.
Remove cold/warm state printing as those are not very useful.
old printing:
si2168 6-0064: found a 'Silicon Labs Si2168' in cold state
si2168 6-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 6-0064: firmware version: 4.0.11
si2168 6-0064: found a 'Silicon Labs Si2168' in warm state
new printing:
si2168 6-0064: found a 'Silicon Labs Si2168-B40'
si2168 6-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 6-0064: firmware version: 4.0.11
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
commit 034e1ec0ce
si2168: One function call less in si2168_init() after error detection
That commit added goto label for error path to release firmware,
but forgets to remove variable NULL set. Remove those now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All known old firmware firmware formats are downloaded using 8 byte
chunks. Reject firmware if it could not be divided to 8 byte chunks
and because of that we could simplify some calculations. Now both
supported firmware download routines are rather similar.
Cc: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use own label for kzalloc failure in which does not call kfree().
kfree() could be called with NULL, but it is still better to have
own label which skips unnecessary kfree().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change formatter from signed to unsigned as stream_id is 32bit
unsigned variable.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Even firmware version is not needed to know, it is still interesting
and useful to know some cases. Due to that increase its printing to
info log level.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename some goto labels and more. No functionality changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove if () from firmware command error path as there should not be
any error prone conditional logic there. Use goto labels instead.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We don't need that anymore as same pointer is passed to each
routine via struct dvb_frontend private field.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Carry struct i2c_client pointer inside struct dvb_frontend private
pointer. This driver is I2C driver, which is represented as a
struct i2c_client, so better to carry this top level structure for
each routine in order to unify things. This allows further
simplification.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
'dev' is most common name in kernel for structure containing device
state instance, so rename it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
w_scan complains about missing symbol rate limits:
This dvb driver is *buggy*: the symbol rate limits are undefined - please report to linuxtv.org
Chip supports 1 to 7.2 MSymbol/s on DVB-C.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for controlling TP clock mode for VSB and QAM annex-B/C mode.
Gated clock mode is the default value, and does not support QAM annex-C.
The patch enables setting this control to fixed clock mode.
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify the code a little bit by removing some uneeded arguments
to lgdt3305_mpeg_mode_polarity().
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I found a problem on vc032x gspca usb webcam subdriver: "bytesperline"
property is wrong for YUYV and YVYU formats.
With recent v4l-utils library (>=0.9.1), that uses "bytesperline" for
pixel format conversion, the result is a wrong jerky image.
Patch tested on my laptop (USB webcam Logitech Orbicam 046d:0892).
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=91181
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
"n" is a user controlled integer. The code here doesn't handle the case
where "n" is negative and this causes a static checker warning.
drivers/media/usb/gspca/gspca.c:1571 vidioc_s_parm()
warn: no lower bound on 'n'
parm.capture.readbuffers is unsigned, so make n unsigned too, fixing this.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support in the PS3 Eye driver for QVGA capture at higher
frame rates: 187, 150, and 137 FPS. This functionality is valuable
because the PS3 Eye is popular for computer vision projects and no
other camera in its price range supports such high frame rates.
Correct a QVGA mode that was listed as 40 FPS. It is really 37 FPS
(half of 75 FPS).
Tests confirm that the nominal frame rates are achieved.
Signed-off-by: Joe Howse <josephhowse@nummist.com>
Tested-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If start_streaming fails, then the buffers must be given back to vb2 with state
QUEUED, not ERROR. Otherwise a WARN_ON will be generated.
In the disconnect it is pointless to call pwc_cleanup_queued_bufs() as stop_streaming()
will be called anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the larger fifo found on sun5i and sun6i, having a separate
compatible for the ir found on sun5i & sun6i also is useful if we ever want
to add ir transmit support, because the sun5i & sun6i version do not have
transmit support.
Note this commits also adds checking for the end-of-packet interrupt flag
(which was already enabled), as the fifo-data-available interrupt flag only
gets set when the trigger-level is exceeded. So far we've been getting away
with not doing this because of the low trigger-level, but this is something
which we should have done since day one.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On sun6i the cir block is attached to the reset controller, add support
for de-asserting the reset if a reset controller is specified in dt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Checkpatch complained about a few issues, like FSF address. Also,
multi-line comments are not following the Kernel CodingStyle.
While not too late, let's fix those issues.
Cc: John McMaster <johndmcmaster@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adds support for AmScope MU800 / ToupTek UCMOS08000KPB USB microscope camera.
Signed-off-by: John McMaster <johndmcmaster@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When converting to or from Y'CbCr and R'G'B' the Y offset depends
on the quantization range: it's 0 for full and 16 for limited range.
But in the code it was hardcoded to 16. This messed up the brightness
of the generated pattern.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_read_number() is defined in of.h but does not return an error code, so
that non-of implementation could simply return an error.
Temporarily work around this until of_read_number() can be replaced by
of_property_read_u64_array().
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We must unregister frontend first and after that driver itself. That
order went wrong after demod drivers were switched to kernel I2C
drivers, causing crashes.
Tested-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As rtl2832 driver support now I2C binding we will switch to that one.
Tested-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert that driver to I2C driver model.
Legacy DVB binding is left also for later removal...
Tested-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The UVC spec is a bit vague wrt devices using bulk endpoints,
specifically, how to signal to a device to start streaming.
For devices using isoc endpoints, the sequence for start streaming is:
1) The host sends PROBE_CONTROL(SET_CUR) PROBE_CONTROL(GET_CUR)
2) Host selects desired config and calls COMMIT_CONTROL(SET_CUR)
3) Host selects an alt interface other then zero - e.g SELECT_ALTERNATE_INTERFACE(1)
4) The device starts streaming
However for devices using bulk endpoints, there must be *no* alt interface
other than setting zero. From the UVC spec:
"A VideoStreaming interface containing a bulk endpoint for streaming shall
support only alternate setting zero. Additional alternate settings containing
bulk endpoints are not permitted in a device that is compliant with the Video
Class specification."
So for devices using bulk endpoints, step #3 above is irrelevant, and thus
cannot be used as an indication for the device to start streaming.
So in practice, such devices start streaming immediately after a
COMMIT_CONTROL(SET_CUR).
In the uvc resume() handler, an unsolicited commit is sent, which causes
devices using bulk endpoints to start streaming unintentionally.
This patch modifies resume() handler to send a commit only if streaming
needs to be reestablished, i.e if the device was actually streaming before is
was suspended.
Signed-off-by: Aviv Greenberg <aviv.d.greenberg@intel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
LNE bit in VI6_DISP_IRQ_STA register are from the 0 bit to 4 bit.
This fixes bit position specified by VI6_DISP_IRQ_STA_LNE.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
LNEE bit in VI6_DISP_IRQ_ENB register are from the 0 bit to 4 bit.
This fixes bit position specified by VI6_DISP_IRQ_ENB_LNEE.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
According to the spec, the minimum input pixel size for BRU is 1px,
not 4px.
Signed-off-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new logging functions from the hdmi module.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to jump to the 'err' label as we can simply return the error
code directly and make the code shorter.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The "i" variable is used as an offset into both the dev->vfd[] and the
dev->devtype->vdevs[] arrays. The second array is smaller so we should
use that as a limit instead of ARRAY_SIZE(dev->vfd). Also the original
check was off by one.
We should use a format string as well in case the ->name has any funny
characters and also to stop static checkers from complaining.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Improve g_tuner and add s_hw_freq_seek and enum_freq_bands support for cards
with TEA575x radio.
This allows signal/stereo detection and HW seek to work on these cards.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Split ioctl interface from enum_freq_bands, g_tuner and s_hw_freq_seek
functions and export them to be used in other drivers like bttv.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove tea575x-specific code from bttv and use the common driver instead.
Only set_frequency is implemented (signal/stereo detection or seek would
require more changes to bttv).
It works fine on Video Highway Xtreme (it actually makes the radio usable as
it currently cannot be tuned properly).
Miro/Pinnacle is untested but seems to be simple and should work.
However, I don't understand the Terratec Active Radio Upgrade code. The HW
seems to need IOR, IOW and CSEL signals that were taken from ISA bus on
older cards (IOR and IOW directly and CSEL from some address decoder) and
are emulated here using GPIOs. But the code manipulating these signals in
bttv seems to be broken - it never asserts the IOR signal. If anyone has
this HW, please test if I got that right.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the function pvr2_hdw_cmd_powerdown() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Removes some functions that are not used anywhere:
test_read() edid_read_block() dpp_write() dpp_read()
esdp_write() esdp_read() cec_write_clr_set()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the function vsp1_hsit_read() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the function saa7134_queue() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the function write_eeprom_byte() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Removes some functions that are not used anywhere:
vblanking() hblanking()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Based on versioncheck.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Based on versioncheck.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
The semantic patch also changes the cast to long to a cast to unsigned
long in the data initializer, as unsigned long is the type of the data field.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-t.function = f;
-t.data = d;
-init_timer(&t);
+setup_timer(&t,f,d);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The videobuf_dma_init* and videobuf_dma_map() functions are no longer
used except in videobuf-dma-sg.c itself. Make them static.
These functions were abused in various drivers. All those drivers
have now been fixed, so by no longer exporting these functions
future abuse is now prevented.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the function fm_rx_get_rds_system() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To be future-proof and for better readability the time comparisons are
modified to use time_after() instead of plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As mx53 is a dt-only architecture we can safely remove its entry from the
coda_platform_ids[] structure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUxbzlAAoJEHm+PkMAQRiGtqYIAJ8YlKX9cXKYmXx8/FncINH+
2erj94KyHG080R1uwSq1+7zXWCZUUlxiJnDnsup5rG0dImcicqgOE48oHax1aN6b
yHfPONkTjNJ1HYepuGC3YWCG9wIjPZQ5S8KHrwRjyVoE+ddhe9gWgvArA3jl/fW/
2fYNWekoRoMcRiNb4/w2weyOOBywdSVpmj0WYiwdztysG2ymw5hUXRHJhvSf1AFm
RQJfUHkhCOYpQGY7XFba/1uGhTJfOgDmYAfspAOLzmrXE/DJcCutsVdBZO+12fAL
nhGpM/PkRYxMvwzDKIUoG35qsymYOMqo54oXhr0S2JjyXTGdGmB6qHxIfqnV5Tk=
=O/Lr
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rc6' into patchwork
This is needed in order to get the media fixes applied on -rc6.
Linux 3.19-rc6
* tag 'v3.19-rc6': (891 commits)
Linux 3.19-rc6
dm: fix handling of multiple internal suspends
hwmon: (i5500_temp) Convert to use ATTRIBUTE_GROUPS macro
hwmon: (i5500_temp) Convert to module_pci_driver
hwmon: (i5500_temp) Don't bind to disabled sensors
hwmon: (i5500_temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets
arm64: dts: add baud rate to Juno stdout-path
Revert "platform: x86: dell-laptop: Add support for keyboard backlight"
Revert "Documentation: Add entry for dell-laptop sysfs interface"
dm cache: fix problematic dual use of a single migration count variable
dm cache: share cache-metadata object across inactive and active DM tables
of/unittest: Overlays with sub-devices tests
KVM: x86: SYSENTER emulation is broken
KVM: x86: Fix of previously incomplete fix for CVE-2014-8480
arm64: dump: Fix implicit inclusion of definition for PCI_IOBASE
x86/tsc: Change Fast TSC calibration failed from error to info
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
x86, mm: Change cachemode exports to non-gpl
x86, tls: Interpret an all-zero struct user_desc as "no segment"
...
Conflicts:
drivers/media/pci/cx23885/cx23885.h
The debug parameter is not used anymore, as this module was
converted already to use dev_dbg().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Increase si2168 cmd execute timeout to prevent firmware load failures. Tests
shows it takes up to 52ms to load the 'dvb-demod-si2168-a30-01.fw' firmware.
Increase timeout to a safe value of 70ms.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yD+L
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fix some race conditions caused by a regression on videobuf2
- fix a interrupt release bug on cx23885
- fix support for Mygica T230 and HVR4400
- fix compilation breakage when USB is not selected on tlg2300
- fix capabilities report on ompa3isp, soc-camera, rcar_vin and
pvrusb2
* tag 'media/v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] omap3isp: Correctly set QUERYCAP capabilities
[media] cx23885: fix free interrupt bug
[media] pvrusb2: fix missing device_caps in querycap
[media] vb2: fix vb2_thread_stop race conditions
[media] rcar_vin: Update device_caps and capabilities in querycap
[media] soc-camera: fix device capabilities in multiple camera host drivers
[media] Fix Mygica T230 support
[media] cx23885: Split Hauppauge WinTV Starburst from HVR4400 card entry
[media] tlg2300: Fix media dependencies
device_caps in struct v4l2_capability were inadequately set in
VIDIOC_QUERYCAP. Fix this. Without this a WARN_ON in the v4l2 core
is triggered. This WARN_ON was added for kernel 3.19 exactly to
detect these situations.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The VIDIOC_QUERYCAP function should set device_caps, but this was missing.
In addition, it set the version field as well, but that should be done by
the core, not by the driver.
If a driver doesn't set device_caps the v4l2 core will issue a WARN_ON, so
it's important that this is set correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The locking scheme inside the vb2 thread is unsafe when stopping the
thread. In particular kthread_stop was called *after* internal data
structures were cleaned up instead of doing that before. In addition,
internal vb2 functions were called after threadio->stop was set to
true and vb2_internal_streamoff was called. This is also not allowed.
All this led to a variety of race conditions and kernel warnings and/or
oopses.
Fixed by moving the kthread_stop call up before the cleanup takes
place, and by checking threadio->stop before calling internal vb2
queuing operations.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.16 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The V4L2 API requires both .capabilities and .device_caps fields of
struct v4l2_capability to be set. Otherwise the compliance checker
complains and since commit "v4l2-ioctl: WARN_ON if querycap didn't fill
device_caps" a compile-time warning is issued. Fix this non-compliance
in the rcar_vin driver.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The V4L2 API requires both .capabilities and .device_caps fields of
struct v4l2_capability to be set. Otherwise the compliance checker
complains and since commit "v4l2-ioctl: WARN_ON if querycap didn't fill
device_caps" a compile-time warning is issued. Fix this non-compliance
in several soc-camera camera host drivers.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 2adb177e57 removed 2 devices
from the cxusb device table but failed to fix up the T230 properties
that follow, meaning that this device no longer gets detected properly.
Adjust the cxusb_table index appropriate so detection works.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Unconditionally attaching Si2161/Si2165 demod driver
breaks Hauppauge WinTV Starburst.
So create own card entry for this.
Add card name comments to the subsystem ids.
This fixes a regression introduced in 3.17 by
36efec48e2 ([media] cx23885: Add si2165 support for HVR-5500)
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
CC: stable@vger.kernel.org # for 3.17 and upper
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1) I2C slave addresses were printed so called 8-bit format. Use
standard 7-bit notation.
2) I2C slave address was printed with hex formatted without leading
zeros, which makes output one digit shorter in a case of address
fit to one hex digit. Use 4 char wide hex number with leading zeros
as usually used for I2C slave addresses.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Demod I2C client should be NULL after demod is unregistered on error
path, otherwise it will be unregistered again when driver is unload.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If NO_DMA=y:
drivers/built-in.o: In function `vb2_vmalloc_dmabuf_ops_detach':
videobuf2-vmalloc.c:(.text+0x6f11b0): undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `vb2_vmalloc_dmabuf_ops_map':
videobuf2-vmalloc.c:(.text+0x6f1266): undefined reference to `dma_unmap_sg'
videobuf2-vmalloc.c:(.text+0x6f1282): undefined reference to `dma_map_sg'
As we don't want to make the core VIDEOBUF2_VMALLOC depend on HAS_DMA
(it's v4l2 core code, and selected by a lot of drivers), stub out the
DMA support if HAS_DMA is not set.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since commit da6e162d6a ("[media] rc-core: simplify sysfs code"), when
the IR protocol is set using the sysfs interface to the same set of
protocols that are already set, store_protocols() does not refresh the
scancode filter with the new protocol, even if it has already called the
change_protocol() callback successfully. This results in the filter
being disabled in the hardware and not re-enabled until the filter is
set again using sysfs.
Fix in store_protocols() by still re-applying the filter whenever the
change_protocol() driver callback succeeded.
The problem can be reproduced with the img-ir driver by setting a
filter, and then setting the protocol to the same protocol that is
already set:
$ echo nec > protocols
$ echo 0xffff > filter_mask
$ echo nec > protocols
After this, messages which don't match the filter were still being
received.
Fixes: da6e162d6a ("[media] rc-core: simplify sysfs code")
Reported-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: David Härdeman <david@hardeman.nu>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Biphase decoding in the current img-ir has got a quirk, where multiple
Interrupts are generated when an incomplete IR code is received by the
decoder.
Patch adds a work around for the quirk and enables biphase decoding.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add toggle bit to struct img_ir_scancode_req so that protocols can
provide it to img_ir_handle_data(), and pass that toggle bit up to
rc_keydown instead of 0.
This is needed for the upcoming rc-5 and rc-6 patches.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The information being requested of hardware decode callbacks through
the img-ir-hw scancode API is mounting up, so combine it into a struct
which can be passed in with a single pointer rather than multiple
pointer arguments. This allows it to be extended more easily without
touching all the hardware decode callbacks.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-video. Fix these.
Fixes: a61f68119a ("[media] em28xx-video: implement em28xx_ops: suspend/resume hooks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-dvb. Fix these.
Fixes: ca2b46dacb ("[media] em28xx-dvb: implement em28xx_ops: suspend/resume hooks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-audio. Fix these.
Fixes: 6d746f91f2 ("[media] em28xx-audio: implement em28xx_ops: suspend/resume hooks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-audio. Fix these.
Fixes: 1b3fd2d342 ("[media] em28xx-audio: don't hardcode audio URB calculus")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-core. Fix these.
Fixes: 9c669b7314 ("[media] em28xx: add suspend/resume to em28xx_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-input. Fix these.
Fixes: 5025076aad ("[media] em28xx-input: implement em28xx_ops: suspend/resume hooks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The lockdep splat addressed in a previous commit revealed that at
least one message in em28xx-input.c was missing a new line:
em28178 #0: Closing input extensionINFO: trying to register non-static key.
Further inspection shows several other messages also miss a new line.
These will be fixed in a subsequent patch.
Fixes: aa929ad783 ("[media] em28xx: print a message at disconnect")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add xtal as a configuration parameter so it can be used
in the IF register value calculation.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds Video Processing Front End (VPFE) driver for
AM437X family of devices
Driver supports the following:
- V4L2 API using MMAP buffer access based on videobuf2 api
- Asynchronous sensor/decoder sub device registration
- DT support
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
[hans.verkuil@cisco.com: swapped two lines to fix vpfe_release() & add pinctrl include]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This makes the macros a little bit safer.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pll_flags quirk just returned the extra PLL flags the sensor required,
but the init quirk is far more versatile. It can be used to perform any
extra initialisation needed by the sensor, including allocating memory for
sensor specific struct and creating sensor specific new controls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As the controls creation is separated in two sections, the available media
bus codes and link frequencies can be enumerated later on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The default values and limits for certain controls need the knowledge of
available media bus codes or link frequencies. Create such controls later
on, so that most of the initialisation of the sensor has already been done
when the init quirk is called.
[mchehab@osg.samsung.com: make checkpatch.pl happier]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Clean up smiapp_init_controls() by adding newlines to appropriate places and
by removing superfluous error handling. The caller will clean up control
handlers in any case if the function fails.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Also call smiapp_cleanup() in smiapp_remove(), replacing code that did the
same than the function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The flash capability register is already read as part of the limit
registers. Do no access it separately; instead use the value from the
limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In the case of platform data, ISPs that provide clocks to the sensor must
probe before the sensor does. Accessing the sensor does require the clocks,
and thus, probe cannot access the sensor in such a system.
This limitation does not exist in the case of the DT. Perform all
initialisation except Media entity initialisation, link creation and
sub-device registration in probe.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The registered callback is called by the V4L2 async framework after the
bound callback. This allows separating the functionality in the registered
callback so that on DT based systems only sub-device registration is done
there.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platform data support is retained.
of_property_read_u64_array() isn't used yet as it's not in yet.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SMIA compatible sensors only need a single clock.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The source sub-device's name will be overwritten shortly. Don't give it a
name in the meantime.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
struct device has a forward declaration in the header already. The header is
only needed in the .c file.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove FSF's address information from the license header in the smiapp
driver and the smiapp-pll PLL calculator. This should no longer be needed,
and would be rendered outdated in case the FSF chooses to relocate its
office.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Timo Ahonen <timo.ahonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If VIDEO_CAFE_CCIC=y, but VIDEOBUF2_DMA_SG=m:
drivers/built-in.o: In function `mcam_v4l_open':
mcam-core.c:(.text+0x1c2e81): undefined reference to `vb2_dma_sg_memops'
mcam-core.c:(.text+0x1c2eb0): undefined reference to `vb2_dma_sg_init_ctx'
drivers/built-in.o: In function `mcam_v4l_release':
mcam-core.c:(.text+0x1c34bf): undefined reference to `vb2_dma_sg_cleanup_ctx'
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver supports VBI and the comment "VBI support
is not yet working" is inaccurate. Remove it.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:344:20: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:354:20: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:364:24: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:366:23: warning: cast to restricted __le16
The get_unaligned_le*() functions return the value using cpu endianness,
so calling le*_to_cpu is wrong.
It hasn't been not noticed because this code has only been run on little
endian systems, so le*_to_cpu doesn't do anything.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
The be16_to_cpu conversions in m5mols_get_version() are not needed since the
data is already using cpu endianness. This was never noticed since these
version fields are never used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/hd29l2.c:29:18: warning: Variable length array is used.
drivers/media/dvb-frontends/hd29l2.c:34:32: error: cannot size expression
drivers/media/dvb-frontends/hd29l2.c:125:5: warning: symbol 'hd29l2_rd_reg_mask' was not declared. Should it be static?
Variable length arrays are frowned upon, so replace with a fixed length and check
that there won't be a buffer overrun.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix this warning:
drivers/media/v4l2-core/videobuf2-vmalloc.c:98:28: warning: incorrect type in assignment (different address spaces)
drivers/media/v4l2-core/videobuf2-vmalloc.c:158:28: warning: incorrect type in argument 1 (different address spaces)
The warning is correct, but we have no other choice here to forcibly cast.
At least it is now explicit that such a cast is needed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix this warning:
drivers/media/pci/ivtv/ivtv-irq.c:418:9: warning: context imbalance in 'ivtv_dma_stream_dec_prepare' - different lock contexts for basic block
sparse didn't quite understand the locking scheme, so rewrite it to keep
sparse happy.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixes these sparse warnings.
drivers/media/pci/ttpci/budget-core.c:250:17: warning: context imbalance in 'ttpci_budget_debiread' - different lock contexts for basic block
drivers/media/pci/ttpci/budget-core.c:289:17: warning: context imbalance in 'ttpci_budget_debiwrite' - different lock contexts for basic block
To be honest, the new code does look better than the old.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/pci/ttpci/av7110.c:1226:15: warning: memset with byte count of 192512
Instead of memsetting this in one go, loop over each line and memset each line
separately.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The old debug field is renamed to dev_debug to ensure that existing drivers
(including out-of-tree drivers) that try to use the old name will no longer
compile. A comment has also been added that makes it explicit that drivers
shouldn't use this field.
Additional bits have been added to the debug flag to be more fine-grained
when debugging, especially when dealing with streaming ioctls and read,
write and poll. You want to enable those explicitly to prevent flooding
the log when streaming unless you actually want to do that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The debug field in struct video_device is for internal use only and
drivers should mix that with their own debug module options.
It is handled by the V4L2 core and users can set it using
/sys/class/video4linux/<devX>/debug.
It has been deprecated for some time now, so it is time to remove it
completely from the drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Dropping code (introduced in 316d9e84a7)
which intends to make raising of motion events more "smooth"(?).
It made motion event never appear in my installation.
That code is complicated, so I couldn't figure out quickly how to fix
it, so dropping it seems better to me.
Another justification is that anyway application would implement
"motion signal stabilization" if required, it is not necessarily kernel
driver's job.
Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video output functionality never worked for this driver. Now remove the
creation of the output video nodes as well to prevent users from thinking
that video output is available, when it isn't.
To correctly implement this the video output should use vb2 as well, and
that requires rewriting the output DMA setup. But without hardware to test
I am not able to do that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the VIDIOC_CREATE_BUFS ioctl. This was missing in this
driver and in vb2 it's trivial to add.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch converts the cx25821 driver from the old videobuf framework to
the new vb2 framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The alsa driver uses videobuf low-level functions that are not
available in vb2, so replace them by driver-specific functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The btcx-risc module is no longer used by other drivers except for bttv.
So move it from common to bt8xx and make it part of the bttv driver instead
of as a separate module.
This module should never have been a common module since most of the code
has always been bttv specific.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove this comment block, it's unused. This removes the btcx_riscmem
reference as well, since that will no longer be available to other
drivers except bttv.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those btcx_risc functions are meant for use with bttv, other drivers
should just allocate the memory themselves.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Regardless of a number of inputs, we should always enable virtual RPF
when BRU is used. This allows the case when there's only one input to
BRU, and a size of the input is smaller than a size of an output of BRU.
Signed-off-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Source address of VSP1 RPF needs to be reset whenever crop offsets are
recalculated.
This correctly reflects a crop setting even VIDIOC_QBUF is called
before VIDIOC_STREAMON is called.
Signed-off-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that all platforms instantiate the VSP1 through DT, platform data
support isn't needed anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Magewell XI100DUSB-HDMI[1] video capture device reports the pixel
format "e436eb7d-524f-11ce-9f53-0020af0ba770". This is its GUID for
BGR 8:8:8.
The UVC 1.5 spec[2] only defines GUIDs for YUY2, NV12, M420 and I420.
This seems to be an extension documented in the Microsoft Windows Media
Format SDK[3] - or at least the Media Format SDK was the only hit that
Google gave when searching for the GUID. This Media Format SDK defines
this GUID as corresponding to `MEDIASUBTYPE_RGB24`. Note though, the
XI100DUSB outputs BGR e.g. byte-reversed. I don't know if its the
capture device in error or Microsoft mean BGR when they say RGB.
[1]: http://www.magewell.com/hardware/dongles/xi100dusb-hdmi/xi100dusb-hdmi_features.html?lang=en
[2]: http://www.usb.org/developers/docs/devclass_docs/USB_Video_Class_1_5.zip
[3]: http://msdn.microsoft.com/en-gb/library/windows/desktop/dd757532(v=vs.85).aspx
Signed-off-by: William Manley <will@williammanley.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch drops driver specific wait_prepare() and wait_finish()
callbacks from vb2_ops and instead uses the the helpers
vb2_ops_wait_prepare/finish() provided by the vb2 core, the lock member
of the queue needs to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the requested clock rate passed to the XCLK set_rate or round_rate
operation is 0, the driver will try to divide by 0. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These drivers depend on VIDEO_V4L2_SUBDEV_API, which in turn
depends on MEDIA_CONTROLLER. So it is sufficient to just depend
on VIDEO_V4L2_SUBDEV_API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Drop the duplicate get/set_crop pad ops and only use get/set_selection.
It makes no sense to have two duplicate ops in the internal subdev API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The crop and selection pad ops are duplicates. Replace all uses of get/set_crop
by get/set_selection. This will make it possible to drop get/set_crop
altogether.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1) This is not allowed by the kernel coding style
2) Just configure your editor correctly
3) It's really ugly
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kamil Debski <k.debski@samsung.com>
Cc: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1rPM
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull second set of media updates from Mauro Carvalho Chehab:
- Move drivers for really old legacy hardware to staging. Those are
using obsolete media kAPIs and are for hardware that nobody uses for
years. Simply not worth porting them to the new kAPIs. Of course,
if anyone pops up to fix, we can move them back from there
- While not too late, do some API fixups at the new colorspace API,
added for v3.19
- Some improvements for rcar_vin driver
- Some fixups at cx88 and vivid drivers
- Some Documentation fixups
* tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] bq/c-qcam, w9966, pms: move to staging in preparation for removal
[media] tlg2300: move to staging in preparation for removal
[media] vino/saa7191: move to staging in preparation for removal
[media] MAINTAINERS: vivi -> vivid
[media] cx88: remove leftover start_video_dma() call
[media] cx88: add missing alloc_ctx support
[media] v4l2-ioctl: WARN_ON if querycap didn't fill device_caps
[media] vivid: fix CROP_BOUNDS typo for video output
[media] DocBook media: update version number and document changes
[media] vivid.txt: document new controls
[media] DocBook media: add missing ycbcr_enc and quantization fields
[media] v4l2-mediabus.h: use two __u16 instead of two __u32
[media] rcar_vin: Fix interrupt enable in progressive
[media] rcar_vin: Enable VSYNC field toggle mode
[media] rcar_vin: Add scaling support
[media] rcar_vin: Add DT support for r8a7793 and r8a7794 SoCs
[media] rcar_vin: Add YUYV capture format support
These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible. In addition, cheaper and vastly better hardware is
available today.
So these drivers are a prime candidate for removal. If someone is
interested in working on these drivers to prevent their removal, then
please contact the linux-media mailinglist.
Let's be honest, the age of parallel port webcams and ISA video capture
boards is really gone.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver hasn't been tested in a long, long time. The company that made
this chip has gone bust many years ago and hardware using this chip is next
to impossible to find.
This driver needs to be converted to newer media frameworks but due to the
lack of hardware that's going to be impossible. Since cheap alternatives are
easily available, there is little point in keeping this driver alive.
In other words, this driver is a prime candidate for removal. If someone is
interested in working on this driver to prevent its removal, then please
contact the linux-media mailinglist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible.
So these drivers are a prime candidate for removal. If someone is
interested in working on these drivers to prevent their removal, then
please contact the linux-media mailinglist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The start_streaming op is responsible for starting the video dma,
so it shouldn't be called anymore from the buf_queue op.
Unfortunately, this call to start_video_dma() was added to the
start_streaming op, but was forgotten to be removed from the
buf_queue op, which is where it used to be before the vb2 conversion.
Calling this function twice causes very hard to find errors: sometimes
it works, sometimes it doesn't. It took me a whole friggin' day
to track this down, and in the end it was just luck that my eye suddenly
triggered on that line.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx88 vb2 conversion and the vb2 dma_sg improvements were developed separately and
were merged separately. Unfortunately, the patch updating drivers to the dma_sg
improvements didn't take the updated cx88 driver into account. Basically two ships
passing in the night, unaware of one another even though both ships have the same
owner, i.e. me :-)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Chris Lee <updatelee@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is easy to forget to do in drivers. While v4l2-compliance will check for it,
not everyone remembers to run it. So warn about it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
An error was returned if composing was not supported, instead of if
cropping was not supported.
A classic copy-and-paste bug. Found with v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.18
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so Kconfig options
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace PM_RUNTIME with PM in Kconfig dependencies throughout the
tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
The progressive input is captured by the field interrupt.
Therefore the end of frame interrupt is unnecessary.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
By applying this patch, it sets to VSYNC field toggle mode not only
at the time of progressive mode but at the time of an interlace mode.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Based on platform device work by Matsuoka-san.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This became a fairly large pull request. In addition to the usual
driver updates / fixes, there have been a high amount of cleanups in
ASoC area, as well as control API helpers and kernel documentations
fixes touching through the whole tree.
In the driver side, the biggest changes are the support for new Intel
SoC found on new x86 machines, and the updates of FireWire dice and
oxfw drivers.
Some remarkable items are below:
* ALSA core
- PCM mmap code cleanup, removal of arch-dependent codes
- PCM xrun injection support
- PCM hwptr tracepoint support
- Refactoring of snd_pcm_action(), simplification of PCM locking
- Robustified sequecner auto-load functionality
- New control API helpers and lots of cleanups along with them
- Lots of kerneldoc fixes and cleanups
* USB-audio
- The mixer resume code was largely rewritten, and the devices with
quirks are resumed properly.
- New hardware support: Focusrite Scarlett, Digidesign Mbox1,
Denon/Marantz DACs, Zoom R16/24
* FireWire
- DICE driver updates with better duplex and sync support, including
MIDI support
- New OXFW driver for Oxford Semiconductor FW970/971 chipset,
including the previous LaCie Speakers device. Fullduplex and MIDI
support included as well as DICE driver.
* HD-audio
- Refactoring the driver-caps quirk handling in snd-hda-intel
- More consistent control names representing the topology better
- Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
fix, ASUS Z99He laptop EAPD
* ASoC
- Conversion of AC'97 drivers to use regmap, bringing us closer to
the removal of the ASoC level I/O code
- Clean up a lot of old drivers that were open coding things that
have subsequently been implemented in the core
- Some DAPM performance improvements
- Removal of the now seldom used CODEC mutex
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers
- Support for Samsung boards using rt5631 as the CODEC
- Removal of the obsolete AFEB9260 machine driver
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks
* Others
- ASIHPI driver update and cleanups
- Lots of dev_*() printk conversions
- Lots of trivial cleanups for the codes spotted by Coccinelle
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sB6v
-----END PGP SIGNATURE-----
Merge tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became a fairly large pull request. In addition to the usual
driver updates / fixes, there have been a high amount of cleanups in
ASoC area, as well as control API helpers and kernel documentations
fixes touching through the whole tree.
In the driver side, the biggest changes are the support for new Intel
SoC found on new x86 machines, and the updates of FireWire dice and
oxfw drivers.
Some remarkable items are below:
ALSA core:
- PCM mmap code cleanup, removal of arch-dependent codes
- PCM xrun injection support
- PCM hwptr tracepoint support
- Refactoring of snd_pcm_action(), simplification of PCM locking
- Robustified sequecner auto-load functionality
- New control API helpers and lots of cleanups along with them
- Lots of kerneldoc fixes and cleanups
USB-audio:
- The mixer resume code was largely rewritten, and the devices with
quirks are resumed properly.
- New hardware support: Focusrite Scarlett, Digidesign Mbox1,
Denon/Marantz DACs, Zoom R16/24
FireWire:
- DICE driver updates with better duplex and sync support, including
MIDI support
- New OXFW driver for Oxford Semiconductor FW970/971 chipset,
including the previous LaCie Speakers device. Fullduplex and MIDI
support included as well as DICE driver.
HD-audio:
- Refactoring the driver-caps quirk handling in snd-hda-intel
- More consistent control names representing the topology better
- Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
fix, ASUS Z99He laptop EAPD
ASoC:
- Conversion of AC'97 drivers to use regmap, bringing us closer to
the removal of the ASoC level I/O code
- Clean up a lot of old drivers that were open coding things that
have subsequently been implemented in the core
- Some DAPM performance improvements
- Removal of the now seldom used CODEC mutex
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers
- Support for Samsung boards using rt5631 as the CODEC
- Removal of the obsolete AFEB9260 machine driver
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks
Others:
- ASIHPI driver update and cleanups
- Lots of dev_*() printk conversions
- Lots of trivial cleanups for the codes spotted by Coccinelle"
* tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
ALSA: pcxhr: NULL dereference on probe failure
ALSA: lola: NULL dereference on probe failure
ALSA: hda - Add "eapd" model string for AD1986A codec
ALSA: hda - Add EAPD fixup for ASUS Z99He laptop
ALSA: oxfw: Add hwdep interface
ALSA: oxfw: Add support for capture/playback MIDI messages
ALSA: oxfw: add support for capturing PCM samples
ALSA: oxfw: Add support AMDTP in-stream
ALSA: oxfw: Add support for Behringer/Mackie devices
ALSA: oxfw: Change the way to start stream
ALSA: oxfw: Add proc interface for debugging purpose
ALSA: oxfw: Change the way to make PCM rules/constraints
ALSA: oxfw: Add support for AV/C stream format command to get/set supported stream formation
ALSA: oxfw: Change the way to name card
ALSA: dice: Add support for MIDI capture/playback
ALSA: dice: Add support for capturing PCM samples
ALSA: dice: Support for non SYT-Match sampling clock source mode
ALSA: dice: Add support for duplex streams with synchronization
ALSA: dice: Change the way to start stream
ALSA: jack: Add dummy snd_jack_set_key() definition
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUhxhbAAoJEAhfPr2O5OEV4JwP/2I7D2KGz5tdNGDAh1H8+swR
hoj3tX7HLhwBmF6XIUlMYbk5L/ClDace6kcjT6OjwJ9SktrrKks6ZSsYsBjCIyOC
yS7xNQArUKzWk4vV+uJVAvtF8V57LLFul8dhHk0JJwAxrkWnPvDdfJNs4PhUAkgn
1i0PPshNo5Ow/+4YMiOjEDR+q9TMSUUzaq5zkPF7AFCnykuJ1wUJwUE0qjTfGi+4
gl1yMye0TEawTYSM8h/+Lh7wosNFZYcXg85r04A6a8h6GLgg0h6KSOJjyPITmQ+j
hLdtyiYs8a6XT+Y8o416zxpbSozo7KXCUTtet/N5g+lgQMqZqSd9WxE52SOY+kfd
UVeob0VfWR0xdDzaJp5rLQ/MQ16RTHaHppgUidFxxGe9D5f9JM/88I0OfwNzl4uO
cv2cyeNktHH6bcjfOGqxSVmZWgAm6q6qU7MN07PoN+5TcUlYTAOi1WLE5K+7HGgw
CxzOZ61oxi/OO1FapaVoipq6ycjltTql2kbcARvmrRrbge0ocAqHxHqFyUbDDhNw
Wn/O6VzLfpW0vGTacC6+xcUSpIhwajJ80UJAOqJP8sw0Xtmian5Lcs6gVzxwkOdU
36Po4RRGFqsG6Sq3HR+toNwKt/nHNEFkJwYcNFHdvBiXTEYYkMe6MccUxxb3i/iI
KxB1s51zVy9t3PqjP+3J
=i7gx
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Pull VFS changes from Al Viro:
"First pile out of several (there _definitely_ will be more). Stuff in
this one:
- unification of d_splice_alias()/d_materialize_unique()
- iov_iter rewrite
- killing a bunch of ->f_path.dentry users (and f_dentry macro).
Getting that completed will make life much simpler for
unionmount/overlayfs, since then we'll be able to limit the places
sensitive to file _dentry_ to reasonably few. Which allows to have
file_inode(file) pointing to inode in a covered layer, with dentry
pointing to (negative) dentry in union one.
Still not complete, but much closer now.
- crapectomy in lustre (dead code removal, mostly)
- "let's make seq_printf return nothing" preparations
- assorted cleanups and fixes
There _definitely_ will be more piles"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
copy_from_iter_nocache()
new helper: iov_iter_kvec()
csum_and_copy_..._iter()
iov_iter.c: handle ITER_KVEC directly
iov_iter.c: convert copy_to_iter() to iterate_and_advance
iov_iter.c: convert copy_from_iter() to iterate_and_advance
iov_iter.c: get rid of bvec_copy_page_{to,from}_iter()
iov_iter.c: convert iov_iter_zero() to iterate_and_advance
iov_iter.c: convert iov_iter_get_pages_alloc() to iterate_all_kinds
iov_iter.c: convert iov_iter_get_pages() to iterate_all_kinds
iov_iter.c: convert iov_iter_npages() to iterate_all_kinds
iov_iter.c: iterate_and_advance
iov_iter.c: macros for iterating over iov_iter
kill f_dentry macro
dcache: fix kmemcheck warning in switch_names
new helper: audit_file()
nfsd_vfs_write(): use file_inode()
ncpfs: use file_inode()
kill f_dentry uses
lockd: get rid of ->f_path.dentry->d_sb
...
Lots and lots of changes this time around, the usual set of driver
updates and a huge bulk of cleanups from Lars-Peter. Probably the most
interesting thing for most users is the Intel driver updates which will
(with some more machine integration work) enable support for newer x86
laptops.
- Conversion of AC'97 drivers to use regmap, bringing us closer to the
removal of the ASoC level I/O code.
- Clean up a lot of old drivers that were open coding things that have
subsequently been implemented in the core.
- Some DAPM performance improvements.
- Removal of the now seldom used CODEC mutex.
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers.
- Support for Samsung boards using rt5631 as the CODEC.
- Removal of the obsolete AFEB9260 machine driver.
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhajpAAoJECTWi3JdVIfQcOsH/00TMeXlkIjnYe+AC9VjEMYN
IAYaXs1UcAfxB4CpS9ik4sb4LQnnxl9aqy5clUZOLHvDAgHmi6L1E8CteJUGFXZ6
/jjpu9/mI975asgyiNP44QDLSNDjzXX6Z1eeXRGvyKMNZkpg4FLfVq9a6ONtf1dw
N3Hl3LG+wvPhAdR/OSKg9eDVnV1iY7mWOWr/9/1q8UhYRpCTL8x70ytBz6tfeU2r
4fQmFma+qefYXvyuqzuiwzSHJKt+46Z35EyNlkCBpVJVErZL2TGOv4H04PjZhg6+
4CR+YGJMSURRhgMCvUCAh4j6a4c+oSXU/LEl9wMcjWMfa3UtZWKojqlK8lYMeoE=
=Pv8r
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.19
Lots and lots of changes this time around, the usual set of driver
updates and a huge bulk of cleanups from Lars-Peter. Probably the most
interesting thing for most users is the Intel driver updates which will
(with some more machine integration work) enable support for newer x86
laptops.
- Conversion of AC'97 drivers to use regmap, bringing us closer to the
removal of the ASoC level I/O code.
- Clean up a lot of old drivers that were open coding things that have
subsequently been implemented in the core.
- Some DAPM performance improvements.
- Removal of the now seldom used CODEC mutex.
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers.
- Support for Samsung boards using rt5631 as the CODEC.
- Removal of the obsolete AFEB9260 machine driver.
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks.
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
The alternative of CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME may be
replaced with CONFIG_PM too.
Make these changes everywhere under drivers/media/.
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Kamil Debski <k.debski@samsung.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ImgTec Infrared decoder block which img-ir drives is only used in
IMGWorks SoCs so far, such as the TZ1090 (Meta based) and the upcoming
Pistachio (MIPS based). Therefore make the driver depend on METAG (for
TZ1090) or MIPS (for Pistachio) or COMPILE_TEST (so that it is included
in x86 allmodconfig builds), to avoid cluttering the Kconfig menu with
drivers for hardware that isn't yet available on other platforms.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The img_ir_register_decoder() and img_ir_unregister_decoder() functions
were dropped prior to the img-ir driver being applied to simplify the
protocol decoder setup. However the declarations of these functions in
img-ir-hw.h were still included. Delete them since they're completely
unused.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The end timer is used for switching back from repeat code timings when
no repeat codes have been received for a certain amount of time. When
the protocol is changed, the end timer is deleted synchronously with
del_timer_sync(), however this takes place while holding the main spin
lock, and the timer handler also needs to acquire the spin lock.
This opens the possibility of a deadlock on an SMP system if the
protocol is changed just as the repeat timer is expiring. One CPU could
end up in img_ir_set_decoder() holding the lock and waiting for the end
timer to complete, while the other CPU is stuck in the timer handler
spinning on the lock held by the first CPU.
Lockdep also spots a possible lock inversion in the same code, since
img_ir_set_decoder() acquires the img-ir lock before the timer lock, but
the timer handler will try and acquire them the other way around:
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.18.0-rc5+ #957 Not tainted
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(((&hw->end_timer))){+.-...}, at: [<4006ae5c>] _call_timer_fn+0x0/0xfc
but this lock was taken by another, HARDIRQ-safe lock in the past:
(&(&priv->lock)->rlock#2){-.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(((&hw->end_timer)));
local_irq_disable();
lock(&(&priv->lock)->rlock#2);
lock(((&hw->end_timer)));
<Interrupt>
lock(&(&priv->lock)->rlock#2);
*** DEADLOCK ***
This is fixed by releasing the main spin lock while performing the
del_timer_sync() call. The timer is prevented from restarting before the
lock is reacquired by a new "stopping" flag which img_ir_handle_data()
checks before updating the timer.
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(((&hw->end_timer))){+.-...}, at: [<4006ae5c>] _call_timer_fn+0x0/0xfc
but this lock was taken by another, HARDIRQ-safe lock in the past:
(&(&priv->lock)->rlock#2){-.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(((&hw->end_timer)));
local_irq_disable();
lock(&(&priv->lock)->rlock#2);
lock(((&hw->end_timer)));
<Interrupt>
lock(&(&priv->lock)->rlock#2);
*** DEADLOCK ***
This is fixed by releasing the main spin lock while performing the
del_timer_sync() call. The timer is prevented from restarting before the
lock is reacquired by a new "stopping" flag which img_ir_handle_data()
checks before updating the timer.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Sifan Naeem <sifan.naeem@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A problem was found on Polaris where if the unit it booted via the power
button on the infrared remote then the next button press on the remote
would return the key code used to power on the unit.
The sequence is:
- The polaris powered off but with the powerdown controller (PDC) block
still powered.
- Press power key on remote, IR block receives the key.
- Kernel starts, IR code is in IMG_IR_DATA_x but neither IMG_IR_RXDVAL
or IMG_IR_RXDVALD2 are set.
- Wait any amount of time.
- Press any key.
- IMG_IR_RXDVAL or IMG_IR_RXDVALD2 is set but IMG_IR_DATA_x is
unchanged since the powerup key data was never read.
This is worked around by always reading the IMG_IR_DATA_x in
img_ir_set_decoder(), rather than only when the IMG_IR_RXDVAL or
IMG_IR_RXDVALD2 bit is set.
Signed-off-by: Dylan Rajaratnam <dylan.rajaratnam@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes the driver on arm.
Reported-by: Steven Guitton <keltiek@gmail.com>
Tested-by: Steven Guitton <keltiek@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dvb_unregister_device() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The release_firmware() function was called in some cases by the si2157_init()
function during error handling even if the passed variable contained still
a null pointer. This implementation detail could be improved
by the introduction of another jump label.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The release_firmware() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As pointed by smatch:
drivers/media/dvb-frontends/stv090x.c:2787 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2789 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2791 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2793 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2795 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
The situation of a buffer overflow won't happen, in practice,
with the current values of car_loop table. Yet, the entire logic
that checks for those registration values is too complex. So,
better to add an explicit check, just in case someone changes
the car_loop tables causing a buffer overflow by mistake.
This also helps to remove several smatch warnings, with is good.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
if STV090x_RANGEOK is not returned, then STV090x_OUTOFRANGE
is returned. However, that part of the code is never reached,
as pointed by smatch:
drivers/media/dvb-frontends/stv090x.c:2673 stv090x_get_sig_params() info: ignoring unreachable code.
So, remove the two uneeded elses, with makes the code a little bit
cleaner.
No functional changes, and one less smatch warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While writing changeset fdf1bc9fa2, I noticed some checkpatch
complains about the CodingStyle for function parameters. So,
clean them.
While here, also removes uneeded "extern" from function prototype.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch is basically produced while testing a tool that
Joe Perches sent upstream sometime ago:
https://lkml.org/lkml/2014/7/11/794
I used it with those arguments:
$ reformat_with_checkpatch.sh drivers/media/usb/em28xx/em28xx*.[ch]
It actually produced 24 patches, with is too much, and showed
interesting things: gcc produced different codes on most of the
patches, even with just linespace changes. The total code data
remained the same on all cases I checked though.
Anyway, provided that we fold the resulting patches, this tool
seems useful.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for new type of firmware versions of Si2168 chip.
Old type: n x 8 bytes (all data, first byte seems to be 04 or 05)
New type: n x 17 bytes (1 byte indicates len and max 16 bytes data)
New version of TechnoTrend CT2-4400 drivers
(http://www.tt-downloads.de/bda-treiber_4.3.0.0.zip) contains newer
firmware for Si2168-B40 that is in the new format. It can be extracted
with the following command:
dd if=ttTVStick4400_64.sys ibs=1 skip=323872 count=6919 of=dvb-demod-si2168-b40-01.fw
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A debug printout for firmware version.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/tuners/tda18271-common.c:176 tda18271_read_extended() warn: if statement not indented
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Drivers that use dvb_attach can have just one exported symbol,
or they will cause compilation breakages depending on the
selected frontends.
As Jim reported:
drivers/built-in.o: In function `technisat_usb2_set_voltage':
technisat-usb2.c:(.text+0x3b4919): undefined reference to `stv090x_set_gpio'
make: *** [vmlinux] Error 1
That happens because, on his configuration, the configuration
is:
CONFIG_DVB_USB=y
CONFIG_DVB_STV090x=m
Luis proposed ar way to fix, but that would just force the
STV090x to be selected, even if one wants to use a device
with a different frontend.
Instead, let's do the right thing: move set_gpio to the
configuration structure and fill it during dvb_attach().
This way, the driver can still call it, and dvb_attach()
will load stv090x module only if the device really needs it.
Reported by: Jim Davis <jim.epost@gmail.com>
Cc: Luis Rodriguez <mcgrof@suse.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove TechnoTrend CT2-4400 and CT2-4650 devices from cxusb.
They are supported by dvb-usb-dvbsky driver in PATCH 3/3.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Recent rtl28xxu patch I made moved demod ADC enable from power control
to frontend control (due to slave demod support). Because of that we
need call USB interface frontend control too in order to enable ADC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function releases the queue if the file being released is the queue
owner. The check reads the queue->owner field without taking the queue
lock, creating a race condition with functions that set the queue owner,
such as vb2_ioctl_reqbufs() for instance.
Fix this by moving the queue->owner check within the mutex protected
section.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vb2_fop_poll() implementation tries to be clever on whether it needs
to lock the queue mutex by checking whether polling might start fileio.
The test requires reading the q->num_buffer field, which is racy if we
don't hold the queue mutex in the first place.
Remove the extra cleverness and just lock the mutex.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for selection target V4L2_SEL_TGT_NATIVE_SIZE. It is equivalent
of what V4L2_SEL_TGT_CROP_BOUNDS used to be. Support for
V4L2_SEL_TGT_CROP_BOUNDS is still supported by the driver as a compatibility
interface.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The fields were previously uninitialised, leaving the returned values to
where the user had set them. This was never the intention.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When compiling under COMPILE_TEST on a x86_64 the following warnings
appear:
drivers/media/platform/omap/omap_vout.c: In function 'omap_vout_uservirt_to_phys':
drivers/media/platform/omap/omap_vout.c:209:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
return virt_to_phys((void *) virtp);
^
drivers/media/platform/omap/omap_vout.c: In function 'omapvid_setup_overlay':
drivers/media/platform/omap/omap_vout.c:420:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
v4l2_dbg(1, debug, &vout->vid_dev->v4l2_dev,
^
drivers/media/platform/omap/omap_vout.c: In function 'omap_vout_buffer_prepare':
drivers/media/platform/omap/omap_vout.c:794:34: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
vout->queued_buf_addr[vb->i] = (u8 *)
^
In file included from arch/x86/include/asm/dma-mapping.h:44:0,
from include/linux/dma-mapping.h:82,
from drivers/media/platform/omap/omap_vout.c:40:
drivers/media/platform/omap/omap_vout.c:803:58: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
dma_addr = dma_map_single(vout->vid_dev->v4l2_dev.dev, (void *) addr,
^
include/asm-generic/dma-mapping-common.h:174:60: note: in definition of macro 'dma_map_single'
#define dma_map_single(d, a, s, r) dma_map_single_attrs(d, a, s, r, NULL)
^
These are fixed by this patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support in the capture driver for using
vb2_ops_wait_prepare/finish() helpers provided by the
vb2 core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vb2_put_vma() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Querycap shouldn't set the version field (the core does that for you),
but it should set the device_caps field.
In addition, remove the CAPTURE and OUTPUT caps for M2M devices. These
were already slated for removal, so it's time to do so.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Querycap shouldn't set the version field (the core does that for you),
but it should set the device_caps field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Cc: Gerhard Sittig <gsi@denx.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Querycap should set the device_caps field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Querycap shouldn't set the version field (the core does that for you),
but it should set the device_caps field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This was missing in this driver, so add this functionality.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for YCbCr output and support setting colorspace,
YCbCr encoding and quantization for the AVI InfoFrame.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement controls to set the YCbCr encoding and the quantization
range for the colorspace.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add AdobeRGB and BT.2020 support.
The colorspace control now orders the colorspaces according to how often
they are used. So rarely used colorspaces are moved to the end. This makes
it more logical when testing colorspace support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the new AdobeRGB and BT.2020 colorspaces. Also support
explicit Y'CbCr and quantization settings.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This extends the precalculated tpg_csc_colors matrix with AdobeRGB and BT.2020
colorspace support.
It also adds two precalculated tables that convert between linear RGB and non-linear
Rec.709 R'G'B' values, i.e. the Rec. 709 transfer function. This is needed to
efficiently handle the BT.2020 Constant Luminance Yc'CbcCrc encoding and decoding.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Log the new ycbcr_enc and quantization fields. Note that it now
also logs the flags field for the multiplanar buffer type. This was
forgotten when the flags field was added.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Amlogic Meson SoCs include a infrared remote control receiver that can
operate in two modes: "NEC" mode in which the hardware decodes frames
using the NEC IR protocol, and "general" mode in which the receiver
simply reports the duration of pulses and spaces for software
decoding.
This is a driver for the IR receiver that implements software decoding
of received frames.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Mauro Carvalho Chehab