The current trigger() has two crucial problems:
1) The DMA request enabling operations (FSL_SAI_CSR_FRDE) for Tx and Rx are
now totally exclusive: It would fail to run simultaneous Tx-Rx cases.
2) The TERE disabling operation depends on an incorrect condition -- active
reference count that only gets increased in snd_pcm_open() and decreased
in snd_pcm_close(): The TERE would never get cleared.
So this patch overwrites the trigger function by following these rules:
A) We continue to support tx-async-while-rx-sync-to-tx case alone, which's
originally limited by this fsl_sai driver, but we make the code easy to
modify for the further support of the opposite case.
B) We enable both TE and RE for PLAYBACK stream or CAPTURE stream but only
enabling the DMA request bit (FSL_SAI_CSR_FRDE) of the current direction
due to the requirement of SAI -- For tx-async-while-rx-sync-to-tx case,
the receiver is enabled only when both the transmitter and receiver are
enabled.
Tested cases:
a) aplay test.wav -d5
b) arecord -r44100 -c2 -fS16_LE test.wav -d5
c) arecord -r44100 -c2 -fS16_LE -d5 | aplay
d) (aplay test2.wav &); sleep 1; arecord -r44100 -c2 -fS16_LE test.wav -d1
e) (arecord -r44100 -c2 -fS16_LE test.wav -d5 &); sleep 1; aplay test.wav -d1
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch improves fsl_sai_isr() in these ways:
1, Add comment for mask fetching code.
2, Return IRQ_NONE if the IRQ is not for the device.
3, Use regmap_write() instead of regmap_update_bits().
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Here is a bunch of small fixes that have been collected since the
previous pull request. In addition to various misc fixes, the
following are included:
- HD-audio quirks for Dell, HP, Chromebook, and ALC28x codecs
- HD-audio AMD HDMI regression fix
- Continued PM support/fixes for ice1712 driver
- Multiplatform fixes for ASoC samsung drivers
- Addition of device id tables to a few ASoC drivers
- Bit clock polarity config and error flag fixes in ASoC fsl_sai
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7zfG
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here is a bunch of small fixes that have been collected since the
previous pull request. In addition to various misc fixes, the
following are included:
- HD-audio quirks for Dell, HP, Chromebook, and ALC28x codecs
- HD-audio AMD HDMI regression fix
- Continued PM support/fixes for ice1712 driver
- Multiplatform fixes for ASoC samsung drivers
- Addition of device id tables to a few ASoC drivers
- Bit clock polarity config and error flag fixes in ASoC fsl_sai"
* tag 'sound-fix-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (32 commits)
ALSA: usb-audio: Suppress repetitive debug messages from retire_playback_urb()
ALSA: hda - Make full_reset boolean
ALSA: hda - add headset mic detect quirk for a Dell laptop
sound: dmasound: use module_platform_driver_probe()
ALSA: au1x00: use module_platform_driver()
ALSA: hda - Use runtime helper to check active state.
ALSA: ice1712: Fix boundary checks in PCM pointer ops
ASoC: davinci-mcasp: Fix bit clock polarity settings
ASoC: samsung: Fix build on multiplatform
ASoC: fsl_sai: Fix Bit Clock Polarity configurations
ALSA: hda - Do not assign streams in reverse order
ALSA: hda/realtek - Add eapd shutup to ALC283
ALSA: hda/realtek - Change model name alias for ChromeOS
ASoC: da732x: Print correct major id
ALSA: hda/realtek - Improve HP depop when system change power state on Chromebook
ASoC: cs42l52: Fix mask for REVID
sound/oss: Remove uncompilable DBG macro use
ALSA: ice1712: Save/restore routing and rate registers
ALSA: ice1712: restore AK4xxx volumes on resume
ASoC: alc56(23|32): fix undefined return value of probing code
...
BugLink: http://bugs.launchpad.net/bugs/1305133
Malfunctioning or slow devices can cause a flood of dmesg SPAM.
I've ignored checkpatch.pl complaints about the use of printk_ratelimit() in favour
of prior art in sound/usb/pcm.c.
WARNING: Prefer printk_ratelimited or pr_<level>_ratelimited to printk_ratelimit
+ if (printk_ratelimit() &&
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Eldad Zack <eldad@fogrefinery.com>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A smattering of device specific fixes, nothing stands out here except
for the multiplatform fixes for Samsung and the device IDs being added
by Stephen Warren - there's no real code changes from those and they
give better robustness to the enumeration with DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Z3Yl
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.15
A smattering of device specific fixes, nothing stands out here except
for the multiplatform fixes for Samsung and the device IDs being added
by Stephen Warren - there's no real code changes from those and they
give better robustness to the enumeration with DT.
The full_reset argument to azx_init_chip() carries boolean rather than
numerical information, so update the type to reflect that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0283,
SID: 0x10280667), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Eliminate boilerplate code by using module_platform_driver_probe().
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Eliminate boilerplate code by using module_platform_driver().
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
From azx_interrupt, use the helper to check if the device is active
instead of checking the state. This will do the right thing if
runtime pm is disabled in addition to if the device is suspended.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PCM pointer callbacks in ice1712 driver check the buffer size boundary
wrongly between bytes and frames. This leads to PCM core warnings
like:
snd_pcm_update_hw_ptr0: 105 callbacks suppressed
ALSA pcm_lib.c:352 BUG: pcmC3D0c:0, pos = 5461, buffer size = 5461, period size = 2730
This patch fixes these checks to be placed after the proper unit
conversions.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
IB_NF, NB_IF and IB_IF configured the bc polarity incorrectly. The receive
polarity was set to the same edge as the TX in these cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
PCM and S/PDIF drivers referenced mach headers for a trivial
data structure. This caused build errors on multiplatform builds
as machine headers are not accessible from driver files. Move the data
structure definition to the driver header and remove the dependency.
While at it rename the structure to avoid multiple definition errors
as the same structure is also used by the platform code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The BCP bit in TCR4/RCR4 register rules as followings:
0 Bit clock is active high with drive outputs on rising edge
and sample inputs on falling edge.
1 Bit clock is active low with drive outputs on falling edge
and sample inputs on rising edge.
For all formats currently supported in the fsl_sai driver, they're exactly
sending data on the falling edge and sampling on the rising edge.
However, the driver clears this BCP bit for all of them which results click
noise when working with SGTL5000 and big noise with WM8962.
Thus this patch corrects the BCP settings for all the formats here to fix
the nosie issue.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently stream numbers are assigned in reverse order.
Unfortunately commit 7546abfb8e ("ALSA: hda - Increment
default stream numbers for AMD HDMI controllers") assumed this was not
the case (specifically, it had the "old cards had single device only"
=> "extra unused stream numbers do not matter" assumption), causing
non-working audio regressions for AMD Radeon HDMI users.
Change the stream numbers to be assigned in forward order.
The benefit is that regular audio playback will still work even if the
assumed stream count is too high, downside is that a too high stream
count may remain hidden.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77002
Reported-by: Christian Güdel <cg@dmesg.ch>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Christian Güdel <cg@dmesg.ch> # 3.14
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add eapd shutup function to alc283_shutup.
It could avoid pop noise from speaker.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Chrome OS was use model name of alc283-dac-wcaps for loading model as default.
Change the model name to same as model name of Chrome OS for future support.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the renamed symbol is defined lib/iomap.c implements ioport_map and
ioport_unmap and currently (nearly) all platforms define the port
accessor functions outb/inb and friend unconditionally. So
HAS_IOPORT_MAP is the better name for this.
Consequently NO_IOPORT is renamed to NO_IOPORT_MAP.
The motivation for this change is to reintroduce a symbol HAS_IOPORT
that signals if outb/int et al are available. I will address that at
least one merge window later though to keep surprises to a minimum and
catch new introductions of (HAS|NO)_IOPORT.
The changes in this commit were done using:
$ git grep -l -E '(NO|HAS)_IOPORT' | xargs perl -p -i -e 's/\b((?:CONFIG_)?(?:NO|HAS)_IOPORT)\b/$1_MAP/'
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DA732X_ID_MAJOR_MASK is 0xF0, so the major id is
(reg & DA732X_ID_MAJOR_MASK) >> 4.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It is better to change Mic2-Vref to manual mode.
Manual control Mic2-Vref will solve pop noise issue.
It will improve pop noise for power on, power off, S3 and resume.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIT[0:2] of register 01h is REVID, so the mask for REVID should be 0x7.
Also updates the code to use CS42L52_CHIP_REV_MASK.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
Most of it duplicates function tracing and one
of them has an uncompilable printf %P use.
Others have format/argument mismatches.
Remove unused DBG1 macro definition
Neaten uart401.c use of ok test around this
DBG macro removal.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Save/restore routing and rate registers during suspend/resume.
This fixes S/PDIF input being disabled after resume.
Tested with Audiophile 24/96.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Also restore AK4xxx mixer volumes on resume for M-Audio ICE1712-based cards.
This fixes incorrect (sound working) zero mixer volumes after resume.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 5d6be5aa ("ASoC: codec: Simplify ASoC probe code.") left variable
'ret', whose value is returned, uninitialized. Since it is not used
otherwise, remove it.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix checking return value of regmap_read().
Also fix reporting the chip_id value. CS42XX8_CHIPID_CHIP_ID_MASK is 0xF0,
so the chip_id value is (val & CS42XX8_CHIPID_CHIP_ID_MASK) >> 4).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <paul.handrigan@cirrus.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add S/PDIF suspend support for M-Audio cards based on ICE1712 chip.
Tested (playback only) on Audiophile 24/96. Capture will probably not work.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Separate HW initialization from device creation.
This is needed for suspend/resume support.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fixups for HP laptops to support the mute LED made the
speaker output silent on some machines. It turned out that they use
the NID 0x18 for the speaker while it's also used for controlling the
LED via VREF bits although the current driver code blindly assumes
that such a node is a mic pin (where 0x18 is usually so).
This patch fixes the problem by only changing the VREF bits and
keeping the other pin ctl bits.
Reported-and-tested-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If it only has single output of HP out of machine.
The driver parser will copy hp_pins to line_out_pins.
hp_pins will empty for alc283_init and alc283_shutup functions.
This will cause not have value for hp_pin_sense.
Add check line_out_type code will solve it .
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull x86 old platform removal from Peter Anvin:
"This patchset removes support for several completely obsolete
platforms, where the maintainers either have completely vanished or
acked the removal. For some of them it is questionable if there even
exists functional specimens of the hardware"
Geert Uytterhoeven apparently thought this was a April Fool's pull request ;)
* 'x86-nuke-platforms-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, platforms: Remove NUMAQ
x86, platforms: Remove SGI Visual Workstation
x86, apic: Remove support for IBM Summit/EXA chipset
x86, apic: Remove support for ia32-based Unisys ES7000
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
alc5632_probe() returns ret, yet it is not initialized or set anywhere.
This ends up causing the function to appear to fail, and audio not to
work on the Toshiba AC100, with my compiler at least.
This function used to set ret in all cases, but recent cleanup removed
that.
Fixes: 5d6be5aa6b ("ASoC: codec: Simplify ASoC probe code.")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A few more updates from last week - use of the tdm_slot mapping from
Xiubo plus a few smaller fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2++i
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Final updates for v3.15 merge window
A few more updates from last week - use of the tdm_slot mapping from
Xiubo plus a few smaller fixes and cleanups.
Add suspend support for M-Audio cards based on ICE1712 chip.
Tested with M-Audio Audiophile 24/96. S/PDIF will probably not work.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add suspend/resume support for ICE1712 chip.
Card-specific subdrivers need to enable it and provide callbacks that suspend/resume the codecs.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The `lspci -nnvv` output contains (wrapped for line length):
00:1b.0 Audio device [0403]:
Intel Corporation 7 Series/C210 Series Chipset Family
High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:115d]
Signed-off-by: W. Trevor King <wking@tremily.us>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This used to be a part of a condition until f3d145aac9 ('ALSA: asihpi:
MMAP for non-busmaster cards') but now it's not and we can remove an
indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's quite cricial to clear error flags because SAI might hang if getting
FIFO underrun during playback (I haven't confirmed the same issue on Rx
overflow though).
So this patch enables those irq and adds isr() to clear the flags so as to
keep playback entirely safe.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When we plug a 3-ring headset on the Dell machines (VID: 0x10ec0255,
SID: 0x10280632; VID: 0x10ec0293, SID: 0x1028062c; VID: 0x10ec0293,
SID: 0x1028062e), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nicolin Chen