McPDM internal FIFO is 24 bit wide. From the 32 bit sample
8 bit is discarded. Let application know about this
via msbits constraint.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Core can set the msbits constraint in behalf of the dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that a regulator device for controlling the codec chip reset state
over a platform agnostic regulator API is available on the only board
using this driver so far, extend the driver with a bias control function
which will request virtual power to the codec chip from that virtual
regulator, and will supersede the present implementation existing at the
sound card level.
Thanks to the regulator sharing mechanism, both the old (the sound card)
and the new (the codec) implementations should coexist smoothly until
the sound card file is updated. For this to work as expected, update the
sound card .set_bias_level callback to not touch codec->dapm.bias_level.
While extending the cx20442 structure, drop unused control_type member.
Created against linxu-3.2-rc6, tested on top of patch 1/4 "ARM: OMAP1:
ams-delta: set up a regulator over the modem reset GPIO pin".
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
This is a follow up on 53dea36c70 which fixes the other affected
pcm engines.
Description from 53dea36c70c1857:
Don't rely on the codec's channels_min information to decide wheter or
not allocate a substream's DMA buffer. Rather check if the substream
itself was allocated previously.
Without this patch I was seeing null-pointer dereferenc in atmel-pcm.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Missed .owner of struct snd_soc_card will prevent the module from being
removed from underneath its users.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In preparation to converting Amstrad Delta on-board latches to
basic_mmio_gpio devices, registration of platform devices which depend
on latches and will require initialization of their GPIO pins first,
should be moved out of .machine_init down to late_initcall level, as the
gpio-generic driver is not available until device_initcall time. The
latch reset operation, which will be replaced with GPIO initialization,
must also be moved to late_initcall for the same reason.
Since there was already another, separate arch_initcall function for
setting up one of those latch dependent devices, the on-board modem
device, reuse that function, i.e., rename it to a name that matches the
new purpose, extend with other device setup relocated from
.machine_init, and move down to the late_initcall level.
While being at it, add missing gpio_free() in case the modem platform
device registration fails.
Thanks to Tony Lindgren <tony@atomide.com> who suggested this approach
instead of shifting up the gpio-generic driver initialization.
In addition, defer registration of the Amstrad Delta ASoC and serio
devices, done from their device driver files, until late_initcall time,
as those drivers will depend on their GPIO pins already requested from
the board late_init() function until updated to register their GPIO pins
themselves.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow McBSP FIFO configuration from ASoC dai driver
on OMAP4 platform.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that the core holds a pm_runtime reference to the device while the
link is active there is no need for the driver to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Now that the core holds a pm_runtime reference to the device while the
link is active there is no need for the driver to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
OMAP4 SDP/Blaze boards have digital microphones.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for OMAP4 Digital Microphone interface.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Factor out some boilerplate code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.
The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pass the DAPM widgets/routes via the snd_soc_card struct
to core.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass the DAPM widgets/routes via the snd_soc_card struct
to core. With this change we do not need the init function
since the remaining snd_soc_dapm_enable_pin calls are
not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass the DAPM widgets/routes and static controls via the
snd_soc_card struct to core. In this way the machine driver
does not need to handle the DAPM widgets/routes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass the DAPM widgets/routes via the snd_soc_card struct
to core. With this change we do not need the init function
since the remaining snd_soc_dapm_enable_pin calls are
not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Widgets are connected by default.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass the DAPM widgets/routes via the snd_soc_card struct
to core.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Widgets are connected by default.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass the DAPM widgets/routes via the snd_soc_card struct
to core.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No need to call soc_dapm_sync at init time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Michael Opdenacker <michael.opdenacker@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After omap_request_dma the BLOCK_IRQ is enabled as default
configuration for the channel.
If we are requested for no period wakeup, we need to disable
the BLOCK_IRQ in order to not receive any interrupts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to use two hw_params callbacks in sdp3430 and zoom2 as
thet are now identical. Use instead the same snd_soc_ops structure and
hw_params callback for both DAI links.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Before commit 75d9ac4 ("ASoC: Allow DAI formats to be specified in the
dai_link") expectation for omap-mcbsp was that snd_soc_dai_set_fmt is to be
called first in machine hw_params callback before other CPU DAI functions.
Thus it was enough that only omap_mcbsp_dai_set_dai_fmt cleared the
mcbsp->regs structure. [Note that this was pure convention, it's always
been OK to set things on init -- broonie]
Now this doesn't hold anymore since machine drivers can set the DAI format
only once on init time and thus mcbsp->regs may get out of sync when other
CPU DAI functions are modifying them dynamically with different values
between the calls. Therefore clear the accessed mcbsp->regs bits and
bitfields in other functions too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 75d9ac4 ("ASoC: Allow DAI formats to be specified in the dai_link")
changed DAI format flag values and we cannot simply invert anymore e.g.
frame-sync with ^= SND_SOC_DAIFMT_NB_IF (which was anyway misuse) as there
is no anymore fixed bit position for bit-clock or frame-sync inversion.
Fix this by relying only on DAI format flag values passed to us and by not
making any assumption on individual bit positions.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The name contains invalid valid character (/), which
causes problems when trying to create the debugfs
directory structure:
ASoC: Failed to create Aux/FM Stereo In debugfs file
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Based on the values from twl6040 codec (HSOTRIM L/R) we can configure
the McPDM offset cancellation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The offset cancellation values can be different from board to board, even
on the same HW platform.
Provide a way for the machine drivers to configure the McPDM offset
cancellation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes the following compile time warning:
omap-mcbsp.c:519: warning: suggest explicit braces to avoid ambiguous ‘else’
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
OMAP4 McPDM supports 5 downlink (playback), and
3 uplink (capture) channels.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Attempt to change McBSP CLKS source while another stream is active is not
safe after commit d135865 ("OMAP: McBSP: implement functional clock
switching via clock framework") in 2.6.37.
CLKS parent clock switching using clock framework have to idle the McBSP
before switching and then activate it again. This short break can cause a
DMA transaction error to already running stream which halts and recovers
only by closing and restarting the stream.
This goes more fatal after commit e2fa61d ("OMAP3: l3: Introduce
l3-interconnect error handling driver") in 2.6.39 where l3 driver detects a
severe timeout error and does BUG_ON().
Fix this by not changing any configuration in omap_mcbsp_dai_set_dai_sysclk
if the McBSP is already active. This test should have been here just from
the beginning anyway.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Change the legacy DAI name from "twl6040-hifi" to "twl6040-legacy" to
be more intuitive.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reasons for the replacement:
The current driver for McPDM was developed to support the legacy mode only.
In preparation for the ABE support the current driver stack need the be
replaced.
The new driver is much simpler, easier to extend, and it also fixes some of the
issues with the old stack.
Main changes:
- single file for omap-mcpdm (mcpdm.c/h removed)
- Define names for registers, bits cleaned up, prefixed
- Full-duplex audio operation (arecord | aplay) has been fixed
- Less code
McPDM need to be turned off after all streams has been stopped.
This might cause pop noise on the output, if the codec's DAC is
still powered at this time.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to probe, and operate correctly, the OMAP McPDM driver needs to
be converted to use hwmod.
The device name has been changed to probe the driver.
Replace the clk_* with pm_runtime_* calls to manage the clocks correctly.
Missing request_mem_region/release_mem_region added.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
DMA packet_size must be configured based on the McPDM FIFO threshold
value, number of channels.
Due to the FIFO operation the DMA muse be configured differently for
playback, and capture.
At the same time fix the McPDM threshold values used for playback, and
capture to avoid broken code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Fix "error: too few arguments to function 'ams_delta_set_bias_level'"
build errors in ams-delta.c that were introduced after commit d4c6005 ("ASoC:
Add context parameter to card DAPM callbacks") by adding dapm context
to ams_delta_set_bias_level calls.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
My gmail account got disabled and I'm not going to reopen it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
It is better if the selection between the Low power,
and High performance PLL is handled within the codec
driver, not in machine driver(s) to avoid duplicated
code, and also to have consistent tracking of the selected
PLL, and the resulting differences in supported sample
rates.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert TWL6040 CODEC driver into a TWL6040 MFD child, it implies
that MFD-level operations like register accesses, clock setting
and power management are done through MFD APIs, not directly by
CODEC driver anymore. To avoid conflicts with the other MFD child,
vibrator registers are skipped in CODEC driver.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename the driver, and header file from twl4030-codec to
twl4030-audio.
To avoid breakage change depending drivers at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Currently pcm_new() passes in 3 arguments :- card, pcm and DAI.
Refactor this to only pass in 1 argument (i.e. the rtd) since struct rtd contains
card, pcm and DAI along with other members too that are useful too.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The card callback will get called for each DAPM context in the card so it
can be useful for it to know which device is currently undergoing a
transition.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Update Makefile and Kconfig to build HDMI audio support for
OMAP4 SDP and Panda boards.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Add machine driver for HDMI audio on OMAP4 boards. This driver is
in charge of putting together the HDMI audio codec and the CPU DAI
and register the HDMI sound card with ALSA.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Addition of the HDMI CPU DAI driver for OMAP4. This driver is in
charge of configuring DMA settings for HDMI. Also, it finds
the HDMI video device and determines if audio playback can proceed.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
OMAP3: PM: Boot message is not an error, and not helpful, remove it
OMAP3: cpuidle: change the power domains modes determination logic
OMAP3: cpuidle: code rework for improved readability
OMAP3: cpuidle: re-organize the C-states data
OMAP3: clean-up mach specific cpuidle data structures
OMAP3 cpuidle: remove useless SDP specific timings
usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
usb: otg: OMAP4430: Fixing the omap4430_phy_init function
usb: musb: am35x: fix compile error when building am35x
usb: musb: OMAP4430: Power down the PHY during board init
omap: drop board-igep0030.c
omap: igep0020: add support for IGEP3
omap: igep0020: minor refactoring
omap: igep0020: name refactoring for future merge with IGEP3
omap: Remove support for omap2evm
arm: omap2plus: GPIO cleanup
omap: musb: introduce default board config
omap: move detection of NAND CS to common-board-devices
omap: use common initialization for PMIC i2c bus
omap: consolidate touch screen initialization among different boards
...
The board support has never been merged for it as noticed
by Russell King <linux@arm.linux.org.uk>. So let's remove the
related dead code.
Cc: linux-fbdev@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Current checks for cpu type were too restrictive leading
to failures for other silicons in same family.
The problem was found while testing audio playback on
AM37x and AM35x processors. But should exist on OMAP36xx
as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
cc: Liam Girdwood <lrg@ti.com>
cc: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Allow disabling ALSA period wakeup interrupts.
This can only be done on OMAP2+ (2/3/4), since there
we can chain the DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
The i2c client device name (".2-001a" in this case, including
the separator period) for the AIC23 codec on the TI AM3517-EVM
was appended to the codec_name member of am3517evm_dai to
resolve the names mismatch happening in soc_bind_dai_link(),
due to which the card was not getting registered.
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
McBSP sidetone is needed in telephony applications. McBSP sidetone is a
configurable FIR filter that forms a loopback from McBSP input to output.
This patch enables the McBSP2 sidetone ALSA controls so that it can be used
on Nokia RX-51/N900.
Sidetone feature can be tested with following commands:
(set up codec input and output paths)
# Enable and configure sidetone
amixer -D hw:0 set 'McBSP2 Sidetone' on
amixer set -D hw:0 'McBSP2 Sidetone Channel 0' 32767
echo 32767 >/sys/devices/platform/omap-mcbsp.2/st_taps
# Do not loop audio via CPU
arecord -f dat >/dev/null |aplay /dev/zero
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Removed the use of macros to obtain base address and DMA channel number.
Instead use the McBSP driver API's that passes base address and DMA
channel number to the client driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Si4713 FM transmitter on Nokia RX-51/N900 is connected to same Line out
signals of TLV320AIC34 than TPA6130 headphone amplifier.
This patch adds route to transmitter and "FM Transmitter" control to keep
route active when needed.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It is more usefull to report headset instead of video out cable in response
to jack insertion as this is more usual use-case and because now the headset
feature is supported. Automatic accessory detection is not possible at the
moment so most sensible static accessory type have to be used.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for headset microphone in Nokia RX-51/N900. The mic
signal from audio jack is routed to codec A LINE1L via two switches and the
mic bias is coming from codec B part.
First switch is the tv-out switch that is already supported and the second
switch selects between voltage detection circuit and codecs. As there is
no use for voltage detection at the moment the second switch is connected
statically to codecs in rx51_soc_init.
Headset can be active when control "Jack Function" is set to "Headset".
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Just slight cleanup to be sync with upcoming change.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The Amstrad Delta ASoC driver used to override the digital_mute()
callback, expected to be not provided by the on-board CX20442 CODEC
driver, with its own implementation. While this is still posssible when
substituting the whole empty snd_soc_dai_driver.ops member (the CX20442
case), replacing snd_soc_dai_ops.digital_mute only is no longer correct
after the snd_soc_dai_driver.ops member has been constified, and results
in build error.
Drop this actually not used code path in hope the CX20442 driver never
provides its own snd_soc_dai_ops structure.
Created and tested against linux-2.6.38-rc2
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Earphone in Nokia RX-51/N900 is connected to left HP output of B part of the
TLV320AIC34 dual codec. In RX-51 the codec A is used as a traditional codec
and the codec B as an auxiliary device.
Audio from codec A goes via the codec B to earphone:
MONO_LOUT of A -> LINE2R of B (B interconnects) -> HPLOUT of B -> Earphone.
Take earphone into use by utilizing the recent ASoC auxiliary and
cross-device support.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.
Search and replace the following:
ARCH_OMAP2420 SOC_OMAP2420
ARCH_OMAP2430 SOC_OMAP2430
ARCH_OMAP3430 SOC_OMAP3430
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Audio jack in Nokia RX-51/N900 is driven by TPA6130 headphone amplifier.
This patch adds support for it and stereo output can be active when
"Jack Function" == "TV-OUT" || "Headphone".
As the TPA6130 can output very high volume levels the output is limited
with snd_soc_limit_volume. Limiting value is found from Maemo kernel sources.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
After multi-component conversion these machine drivers don't actually need
anything from sound/soc/codecs/tlv320aic3x.h so don't include it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds McBSP support for the OMAP4 CPU
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use jack framework to enable detection for the headset microphone
and stereo output in the sdp4430.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add FM stereo pins to the machine driver and add them as a
dapm widget.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Not all omap boards use kernel based pin multiplexing so
CONFIG_SND_OMAP_SOC_N810 should not select it by default as it can make
harm to other boards in multi-board kernels.
Therefore put CONFIG_OMAP_MUX as a dependency to N810 ASoC machine driver.
Thanks to Tony Lindgren <tony@atomide.com> for noticing.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In current implementation, there are resources leak in the error path.
This patch properly reclaims the allocated resources in the error path.
Also adds a missing clk_put in osk_soc_exit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return PTR_ERR(omap3pandora_dac_reg) instead of 0 if regulator_get failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to include soc-dapm.h since soc.h includes it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling Dynamic Audio Power Management (DAPM) from codec devices is
required when developing ASoC further. Such as for other ASoC components to
have DAPM widgets or when extending DAPM to handle cross-device paths.
This patch decouples DAPM related variables from struct snd_soc_codec and
moves them to new struct snd_soc_dapm_context that is used to encapsulate
DAPM context of a device. ASoC core and API of DAPM functions are modified
to use DAPM context instead of codec.
This patch does not change current functionality and a large part of changes
come because of structure and internal API changes.
Core implementation is from Liam Girdwood <lrg@slimlogic.co.uk> with some
minor core changes, codecs and machine driver conversions from
Jarkko Nikula <jhnikula@gmail.com>.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Timur Tabi <timur@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
Cc: Daniel Gloeckner <dg@emlix.com>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the new code introduced with commit cf4c87abe2,
"OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c",
the way omap1 build is supposed to bypass omap2 specific functionality doesn't
optimize out all omap2 specific stuff. This breaks linking phase for omap1
machines, giving "undefined reference to `omap2_mcbsp1_mux_clkr_src'"
and "undefined reference to `omap2_mcbsp1_mux_fsr_src'" errors. Fix it.
Created and tested against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
Commit 346a5c890 (OMAP: control: move plat-omap/control.h
to mach-omap2/control.h) in the linux-omap tree removed
plat/control.h and most of its callers. This one slipped
through - breaking the build as below when
CONFIG_SND_OMAP_SOC_MCPDM is defined. Fix this.
CC sound/soc/omap/omap-mcpdm.o
sound/soc/omap/omap-mcpdm.c:35: fatal error: plat/control.h: No such file or directory
compilation terminated.
make[3]: *** [sound/soc/omap/omap-mcpdm.o] Error 1
make[2]: *** [sound/soc/omap] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It is currently completely normal to execute these machine drivers code on
different boards if the kernel includes support for multiple boards so no
error message should be printed if the machine_is_xxx does not match with
the machine driver.
Therefore remove these pr_err and pr_debug prints in those cases.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Previously the OMAP McBSP ASoC driver implemented CLKS switching by
using omap_ctrl_{read,write}l() directly. This is against policy; the OMAP
System Control Module functions are not intended to be exported to drivers.
These symbols are no longer exported, so as a result, the OMAP McBSP ASoC
driver does not build as a module.
Resolve the CLKS clock changing portion of this problem by creating a
clock parent changing function that lives in
arch/arm/mach-omap2/mcbsp.c, and modify the ASoC driver to use it.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, this symbol must be exported for use by
sound/soc/omap/omap-mcbsp.c.
Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/* and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are. These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The OMAP ASoC McBSP code implemented CLKR and FSR signal muxing via
direct System Control Module writes on OMAP2+. This required the
omap_ctrl_{read,write}l() functions to be exported, which is against
policy: the only code that should call those functions directly is
OMAP core code, not device drivers. omap_ctrl_{read,write}*() are no
longer exported, so the driver no longer builds as a module.
Fix the pinmuxing part of the problem by removing calls to
omap_ctrl_{read,write}l() from the OMAP ASoC McBSP code and
implementing signal muxing functions in arch/arm/mach-omap2/mcbsp.c.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, these symbols must be exported for use by
sound/soc/omap/omap-mcbsp.c.
Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/*, and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are. These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversion.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes sparse warning due non declaration of static function
sound/soc/omap/omap-mcbsp.c:783:5: warning: symbol 'omap_mcbsp_st_info_volsw' was not declared. Should it be static?
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Cc: alsa-devel@alsa-project.org
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Speaker amplifier is controlled by TWL4030 GPIO which may sleep. Therefore
use gpio_set_value_cansleep to get rid of runtime warning that is introduced
after the commit 9c4ba94 and to get a stack trace if ever executing this
code in atomic context.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In the process of unification of codec DAI names while implementing
multi-component, the CX20442 codec DAI has been renamed to "cx20442-hifi".
This new name seems not adequate for a 8kHz voice codec.
Use a better name, "cx20442-voice", as suggested by Liam Girdwood.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.
struct snd_soc_codec ---> struct snd_soc_codec (device data)
+-> struct snd_soc_codec_driver (driver data)
struct snd_soc_platform ---> struct snd_soc_platform (device data)
+-> struct snd_soc_platform_driver (driver data)
struct snd_soc_dai ---> struct snd_soc_dai (device data)
+-> struct snd_soc_dai_driver (driver data)
struct snd_soc_device ---> deleted
This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.
The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.
This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.
Other notable multi-component changes:-
* Stream operations now de-reference less structures.
* close_delayed work() now runs on a DAI basis rather than looping all DAIs
in a card.
* PM suspend()/resume() operations can now handle N CODECs and Platforms
per sound card.
* Added soc_bind_dai_link() to bind the component devices to the sound card.
* Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
DAI link components.
* sysfs entries can now be registered per component per card.
* snd_soc_new_pcms() functionailty rolled into dai_link_probe().
* snd_soc_register_codec() now does all the codec list and mutex init.
This patch changes the probe() and remove() of the CODEC drivers as follows:-
o Make CODEC driver a platform driver
o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
o Removed all static codec pointers (drivers now support > 1 codec dev)
o snd_soc_register_pcms() now done by core.
o snd_soc_register_dai() folded into snd_soc_register_codec().
CS4270 portions:
Acked-by: Timur Tabi <timur@freescale.com>
Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
TI CODEC and OMAP fixes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Samsung platform and misc fixes :-
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
MPC8610 and PPC fixes.
Signed-off-by: Timur Tabi <timur@freescale.com>
i.MX fixes and some core fixes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
J4740 platform fixes:-
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The use of sDMA packet mode in THRESHOLD mode removes the restriction on the
period size.
With the extended THRESHOLD mode user space can ask for any
period size it wishes, and the driver will configure the
sDMA and McBSP FIFO accordingly.
Replace the hw_rule for the period size with static constraint,
which will make sure that the period size will be always
even (to avoid prime period size, which could be possible in
mono stream)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Utilize the sDMA controller's packet syncronization mode, when
the McBSP FIFO is in use (by extending the THRESHOLD mode).
When the sDMA is configured for packet mode, the sDMA frame size
does not need to match with the McBSP threshold configuration.
Uppon DMA request the sDMA will transfer packet size number of
words, and still trigger interrupt on frame boundary.
The patch extends the original THRESHOLD mode by doing the
following:
if (period_words <= max_threshold)
Current THRESHOLD mode configuration
Otherwise (period_words > max_threshold)
McBSP threshold = sDMA packet size
sDMA frame size = period size
With the extended THRESHOLD mode we can remove the constraint
for the maximum period size, since if the period size is
bigger than the maximum allowed threshold, than the driver
will switch to packet mode, and picks the best (biggest)
threshold value, which can divide evenly the period size.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
To make the code a bit more readable, change the indexed
references to the omap_mcbsp_dai_dma_params elements with
pointer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In preparation for the extended threshold mode (sDMA packet mode
support), the code need to be restructured.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds GPIO jack detection to Nokia N900/RX-51. At the moment only
SND_JACK_VIDEOOUT type is reported. More types could be reported after
getting more audio features supported and necessary drivers integrated for
implementing automated accessory detection.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Nokia RX-51/N900 has multifunction 4-pole audio-video jack that can be used
as headphone, headset or audio-video connector. This patch implements the
control 'Jack Function' which is used to select the desired function.
At the moment only TV-out without audio is supported.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
After mass production started it was found that several boards exhibit
noise problems during sound playback. After some investigation it was
determined that CLKX polarity is set incorrectly, and even if most boards
can tolerate the wrong setting, there are some that don't.
Fix polarity setup in the board file. As the clock settings for input and
output now match, merge in and out functions and structures to simplify
code.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
OMAP McBSP FIFO is word structured:
McBSP2 has 1024 + 256 = 1280 word long buffer,
McBSP1,3,4,5 has 128 word long buffer
This means, that the size of the FIFO
depends on the McBSP word size configuration.
For example on McBSP3:
16bit samples: size is 128 * 2 = 256 bytes
32bit samples: size is 128 * 4 = 512 bytes
It is simpler to place constraint for buffer and period based on channels.
McBSP3 as example again (16 or 32 bit samples):
1 channel (mono): size is 128 frames (128 words)
2 channels (stereo): size is 128 / 2 = 64 frames (2 * 64 words)
4 channels: size is 128 / 4 = 32 frames (4 * 32 words)
Use the second method to place hw_rule on buffer size, and in threshold
mode to period size.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolsfonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Save the word length configuration of McBSP, and use that information
to calculate, and configure the threshold in McBSP.
Previously the calculation was only correct when the stream had 16bit
audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolsfonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patchs should allow to use 32-bit samples on e.g. TLV320AIC3x codec,
or others.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for integrated stereo speakers and digital
microphone found on Nokia RX-51 hardware. This is a cut down version based
on Maemo kernel sources and earlier patchset by Eduardo Valentin et al.
http://mailman.alsa-project.org/pipermail/alsa-devel/2009-October/022033.html
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: mixart: range checking proc file
ALSA: hda - Fix a wrong array range check in patch_realtek.c
ALSA: ASoC: move dma_data from snd_soc_dai to snd_soc_pcm_stream
ALSA: hda - Enable amplifiers on Acer Inspire 6530G
ASoC: Only do WM8994 bias off transition from standby
ASoC: Don't use DCS_DATAPATH_BUSY for WM hubs devices
ASoC: Don't do runtime wm_hubs DC servo updates if using offset correction
ASoC: Support second DC servo readback method for wm_hubs
ASoC: Avoid wraparound in wm_hubs DC servo correction
ALSA: echoaudio - Eliminate use after free
ALSA: i2c: cleanup: change parameter to pointer
ALSA: hda - Add MSI blacklist for Aopen MZ915-M
ASoC: OMAP: Fix capture pointer handling for OMAP1510 to work correctly with recent ALSA PCM code
ALSA: hda - Update document about MSI and interrupts
ALSA: hda: Fix 0 dB offset for Lenovo Thinkpad models using AD1981
ALSA: hda - Add missing printk argument in previous patch
ASoC: Fix passing platform_data to ac97 bus users and fix a leak
ALSA: hda - Fix ADC/MUX assignment of ALC269 codec
ALSA: hda - Fix invalid bit values passed to snd_hda_codec_amp_stereo()
ASoC: wm8994: playback => capture
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
[Note that this is a backported version for 2.6.34.
Upstream commit is fd23b7dee]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With recent (2.6.34) chnages in PCM handling, capture stopped working on my
OMAP1510 based Amstrad Delta videophone.
Using 2.6.34-rc2, I was able to correct the problem in 3 different ways:
1. reverting commit 7b3a177b0d,
2. enabling additional jiffies check with
echo 4 >/proc/asound/card0/pcm0c0/xrun_debug
3. applying the patch below.
Since I wasn't able to reproduce the problem on my i686 PC, I guess the
problem is probably machine specific.
The patch reuses the method for software emulation of missing hardware
pointer, already implemented for playback on OMAP1510. It's possible that
event if a hardware pointer is available for capture on this machine, its
behaviour may be not compatible with what upper layer expects.
If you think the problem may be more general and should be solved differently,
on a higher level, I can try to work more on it if you give me a hint.
If the patch gets accepted, I suggest it goes as a fix in the current release
cycle.
Created and tested against linux-2.6.34-rc2.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Basic support for Left Justified coding for OMAP McBSP.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Indentation in initial support for McPDM driver was converted to spaces.
Use tabs to comply with open source coding-style.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the new delay calback function to report the delay through
ALSA for application caused by the internal FIFO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add ASoC interface for OMAP McBSP2 and McBSP3 sidetones.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McPDM platform driver is configured to use sDMA in order to transfer
to/from memory. Support for interfacing with ABE will be added later.
McPDM dai currently supports up to 4 downlink channels and 2 uplink
channels simultaneously, as well as 88.2 and 96 KHz, and a sample
size of 32 bits.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Margarita Olaya <x0080101@ti.com>
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
McPDM is the interface between Phoenix audio codec
and the OMAP4430 processor. It enables data to be transfered
to/from Phoenix at sample rates of 88.4 or 96 KHz.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya <x0080101@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow client drivers to set the data_type (16, 32) and the
sync_mode (element, packet, etc) of the audio dma transferences.
McBSP dai driver configures it for a data type of 16 bits and
element sync mode.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch expands the omap3beagle sound soc for the
beagle board clone DevKit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pandora's external DAC is connected to VSIM TWL4030 supply, so let's
start switching it too to save more power.
Also DAC got it's own DAPM handler.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pandora's external DAC is using 256*Fs output from the TWL4030
codec, and TWL4030 needs to have APLL enabled for it's 256*Fs
output to function.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 761c9d45 (ASoC: Fix build of OMAP sound drivers) changes
CONFIG_MACH_OMAP3517EVM -> CONFIG_SND_OMAP_SOC_OMAP3517EVM in the
Makefile. Whereas the config option defined in Kconfig is
SND_OMAP_SOC_AM3517EVM. Because of this, ASoC driver for AM3517
was not getting compiled.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Recent drivers/mfd/twl4030* renames to twl broke compile for
various boards as the series was missing a patch to change
the board-*.c files.
This patch renames include twl4030.h to include twl.h
and also renames twl4030_i2c_ routines.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Overwrite pin config on intel DG45ID board.
intelhdmi - dont power off HDA link
ALSA: hrtimer - Fix lock-up
ALSA: intelhdmi - add channel mapping for typical configurations
ALSA: intelhdmi - channel mapping applies to Pin
ALSA: intelhdmi - accept DisplayPort pin
ALSA: hda - show HBR(High Bit Rate) pin cap in procfs
ALSA: hda - Fix LED GPIO setup for HP laptops with IDT codecs
ASoC: Fix build of OMAP sound drivers
ALSA: opti93x: fix irq releasing if the irq cannot be allocated
There are build errors when building for some of the omap2/3 boards without
enabling sound:
sound/built-in.o:(.data+0x43bc): undefined reference to `soc_codec_dev_tlv320aic23'
sound/built-in.o:(.data+0x43cc): undefined reference to `tlv320aic23_dai'
Confused me quite a bit since the drivers that had references to the
codec weren't enabled. Turns out the Makefile was using the wrong
config option to enable them. Patch below.
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A while ago TWL4030 had it's playback stream name changed, but
pandora needs it for it's playback path. Update to correct stream
name so that playback works again.
Also mark VIBRA output as not connected.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correcting the license string from GPLv2 -> GPL v2.
Found the problem while building OMAP3 ASoC driver as
module.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch increases the number of supported audio channels from 4
to 16 and has been sponsored by Shotspotter Inc. It also fixes a
FSYNC rate calculation bug when McBSP is FSYNC master.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Upcoming change to omap-mcbsp.c require that machine drivers using OMAP
as a DAI master to pass sample rate generator input clock frequency to
the omap-mcbsp.c DAI driver.
Pandora is using 256*Fs output from the TWL4030 codec as an input clock to
the McBSP sample rate generator.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After DMA burst mode has been introduced in sound/soc/omap/omap-pcm.c,
omap_pcm_prepare() unconditionally calls:
omap_set_dma_src_burst_mode(prtd->dma_ch, OMAP_DMA_DATA_BURST_16);
omap_set_dma_dest_burst_mode(prtd->dma_ch, OMAP_DMA_DATA_BURST_16);
Current implementation of those two functions found in
arch/arm/plat-ompa/dma.c doesn't support OMAP_DMA_DATA_BURST_16 on OMAP1 at
all, so they both end with BUG() on that machine. That results in
ASoC being completely unusable, at least on my OMAP5910 based Amstrad Delta.
The patch corrects the problem by not calling those two functions when run on
OMAP1 class based machines.
Created against linux-2.6.32-rc5.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modifying the Kconfig and Makefile in sound/soc/omap folder
to add support for OMAP3517 / AM3517 EVM in Alsa SoC.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adding support for OMAP3517 / AM3517 EVM in Alsa SoC.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The pop-removal specific values are configured for TWL4030 codec
for OMAP3EVM through this patch.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I thought it could be usefull to add some information on how to get the device
fully supported by loading a line discipline on the modem line.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After DMA burst mode has been introduced in sound/soc/omap/omap-pcm.c,
omap_pcm_prepare() unconditionally calls:
omap_set_dma_src_burst_mode(prtd->dma_ch, OMAP_DMA_DATA_BURST_16);
omap_set_dma_dest_burst_mode(prtd->dma_ch, OMAP_DMA_DATA_BURST_16);
Current implementation of those two functions found in
arch/arm/plat-ompa/dma.c doesn't support OMAP_DMA_DATA_BURST_16 on OMAP1 at
all, so they both end with BUG() on that machine. That results in
ASoC being completely unusable, at least on my OMAP5910 based Amstrad Delta.
The patch corrects the problem by not calling those two functions when run on
OMAP1 class based machines.
Created against linux-2.6.32-rc5.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Hi Mark,
Here is a patch that corrects small omissions I have found in my code.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
The McBSP1 port in OMAP3 processors (I believe OMAP2 too but I don't have
specifications to check it) have additional CLKR and FSR pins for McBSP1
receiver. Reset default is that receiver is using bit clock and frame
sync signal from those pins but it is possible to configure to use
also CLKX and FSX pins as well. In fact, other McBSP ports are doing that
internally that transmitter and receiver share the CLKX and FSX.
Add functionaly that machine drivers can set the CLKR and FSR sources by
using the snd_soc_dai_set_sysclk.
Thanks to "Aggarwal, Anuj" <anuj.aggarwal@ti.com> for reporting the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the write to PMBR1 register through I2C. Also, the constant which
holds the value to write is now called TWL4030_GPIO6_PWM0_MUTE. This
name is based on TRM to avoid confusion.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Functionality of functions omap_mcbsp_xmit_enable and omap_mcbsp_recv_enable
can be merged into omap_mcbsp_start and omap_mcbsp_stop since API of
those omap_mcbsp_start and omap_mcbsp_stop was changed recently allowing
to start and stop individually the transmitter and receiver.
This cleans up the code in arch/arm/plat-omap/mcbsp.c and in
sound/soc/omap/omap-mcbsp.c which was the only user for those removed
functions.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit ca6e2ce086 is setting up few XCCR and
RCCR bits for I2S and DPS_A formats. Part of the bits are already set
for all formats and I believe that XDISABLE and RDISABLE bits are
format independent.
As XCCR and RCCR are found only from OMAP2430 and OMAP34xx, I move setup
of XDISABLE and RDISABLE to where those cpu's are tested and remove format
dependent part for simplicity.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixup the device changes by modifying the files that we just removed the
explicit device creation from with i2c_register_board_info() until this
can be moved into the relevant board files.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The tlv320aic3x driver managed its own i2c device, instead of an extant
one created by the board support code. Change the code to make it so that
the driver binds to an extant (in this case i2c) device.
Add explict tlv320aic33 as well as tlv320aic3x to the supported device
table and remove the old driver bindings from the users of this code.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Configures DMA sync mode depending on McBSP operating mode value.
The value is configurable by McBSP instance. So, depending
on McBSP operating mode, the DMA sync mode is passed from
omap-mcbsp to omap-pcm. Besides that, it also configures
McBSP threshold value depending on which McBSP mode is activated.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch changes the way DMA is done in omap-pcm.c
in order to reduce power consumption. There is no need
to have so much SW control in order to have DMA in idle
state during audio streaming. Configuring McBSP threshold value
and DMA to FRAME_SYNC are sufficient.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All these steps are required for ASoC to behave correctly.
rccr and xccr are format dependent, for example TDM audio
has different values than I2S or DSP_A. Also the
omap_mcbsp_xmit_enable and/or omap_mcbsp_recv_enable must
be called right after the DMA has started.
This provides no longer L and R channels switching at random.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is, no RFIG or XFIG (Not defined in 34xx), correct
initiliazation of rccr and xccr.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Align DMA address to DMA burst transaction sizes.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Improve DMA transfers by enabling Burst transaction.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enhance period_index accuracy, particularly just before buffer rewind, by
making use of DMA interrupt status flags in addition to simply counting up
interrupts.
Created against linux-2.6.31-rc5.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use newly implemented DMA channel self linking on OMAP1510 like on other OMAP
models. Remove unnecessary DMA transfer restart from interrupt handler
routine.
The interrupt routine used to maintain a period index, originally needed for
counting up periods up to a full buffer in order to restart the DMA transfer.
For some time, this counter is also used as a replacement for hardware DMA
progress counter that has been found unusable on OMAP1510 in case of playback.
Thus, the period index calculation cannot be omitted completely. However, the
accuracy of this counter can still suffer from missing DMA interrupts.
In order to work correctly, it requires patch 1 from this series also applied:
[RFC][PATCH 1/3] ARM: OMAP: DMA: Add support for DMA channel self linking on OMAP1510
Created against linux-2.6.31-rc5.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch changes the line discipline name registered in include/linux/tty.h
and updates the ams-delta machine driver to use it.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Simultaneous audio playback and capture on OMAP1510 can cause that second
stream is stalled if there is enough delay between startup of the audio
streams.
Current implementation of the omap_mcbsp_start is starting both transmitter
and receiver at the same time and it is called only for firstly started
audio stream from the OMAP McBSP based ASoC DAI driver.
Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is
missed if there is no DMA transfer set up at that time when the first word
after McBSP startup is transmitted. The problem hasn't noted before since
later OMAPs are using level sensitive DMA request lines.
Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by
allowing to start and stop individually McBSP transmitter and receiver
logics. Then call those functions individually for both audio playback
and capture streams. This ensures that DMA transfer is setup before
transmitter or receiver is started.
Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem
analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA
request line behavior differences between the OMAP generations.
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds machine support for Amstrad E3 (Delta) videophone to ASoC.
Created and tested against linux-2.6.31-rc3.
Applies and works with linux-omap-2.6 commit
7c5cb7862d32cb344be7831d466535d5255e35ac as well.
Depends on:
1) latest version of the CX20442 codec driver that exposes v253_ops
structure[1],
2) patch 2/3 form this series: TTY: Add definition of a new line
discipline required by Amstrad E3 (Delta) ASoC driver[2].
CPU DAI parameters best matching the codec DAI has been selected out
empirically for best user experience.
Board specific audio function control (with related DAPM widgets) has been
modeled after empirically discovered codec capabilities.
Unlike other ASoC machine drivers, this one makes use of a codec provided line
discipline that is required for talking to a modem chip that can control the
codec behavoiur. As the line discipline operations must call board specific
bits as well, the machine driver registers its own line discipline ops, not
the codec provided, and then calls those codec provided from inside its own
callbacks.
If some kind of a glue, like a bus over a tty, exsited that could help in
runtime detection of a modem (bus adapter) over a more generic line discipline
(bus driver)[3], the line discipline code could be probably designed in a
more generic way.
In order to work at all, this driver requires a working McBSP1. On OMAP1510
based machines (not sure if other OMAP1 variants as well), where McBSP1 is a
DSP public peripheral, that means the kernel must provide basic DSP support,
ie. omap_dsp_init(), in order to power up the DSP. This used to be included in
linux-omap-2.6 tree up to commit 2512fd29db4eb09e82d182596304c7aaf76d2c5c.
Without that, the driver would not work, ie. not shift in/out any bits over
the CPU DAI[4]. This limitation is not board, but CPU specific, and may apply
to other code that makes use of McBSP1/McBSP3 on affected machines. I provide
an extra patch (4/3) as a temporary solution.
To work correctly in playback mode, this driver requires my prevoiusly
submitted patch that corrects pcm pointer calculation for OMAP1510 based
machines[5] (already included in linux-2.6.31-rc3).
To support codec controls, this driver requires my previously submitted patch
that adds support for modem found on Amstrad Delta[6].
[1] http://mailman.alsa-project.org/pipermail/alsa-devel/2009-July/019780.html
[2] http://www.spinics.net/lists/linux-serial/msg01862.html
[3] http://www.spinics.net/lists/linux-serial/msg01856.html
[4] http://www.spinics.net/lists/linux-omap/msg15114.html
[5] http://mailman.alsa-project.org/pipermail/alsa-devel/2009-June/018950.html
[6] http://www.spinics.net/lists/linux-omap/msg15432.html
Credits to:
Mark Underwood - for his initial, omap-alsa based sound driver for
this machine,
Mark Brown - for his help, patience and excellent subsytem maintainer support.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Board sdp3430 has hardware support for EXTMUTE using TWL4030 GPIO6
line, controlled by register INTBR_PMBR1. Machine driver takes care
of enabling gpio line through i2c and codec driver manipulates the
line during headset ramp up/down sequence.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for EXTMUTE in Zoom2 machine driver. This is necessary
to further reduce pop noise problem. Signal EXTMUTE is connected to
signal GPIO 153 in Zoom2 board.
In addition, change ramp delay value to 3 (218/161/109 ms). With
previous ramp delay value, pop noise was louder. With a longer value
the beep tone can be observed.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch tries to work around the problem of broken OMAP1510 PCM playback
pointer calculation by replacing DMA function call that incorrectly tries to
read the value form DMA hardware with a value computed locally from an
already maintained variable omap_runtime_data.period_index.
Tested on OMAP5910 based Amstrad Delta (E3) using work in progress ASoC
driver.
Based on linux-2.6-asoc.git v2.6.31-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Voice interface of twl4030 codec supports: CBM_CFM and
CBS_CFS. It doesn't support CBS_CFM.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-By: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for Zoom2 board. Zoom2 machine driver
connects both codec DAIs (audio and voice) to omap3
McBSP ports in the following way:
HiFi <-> McBSP2
Voice <-> McBSP3
The zoom2 driver has the following DAPM widgets:
* Ext Mic: MAINMIC, SUBMIC (with bias)
* Ext Spk: HFL, HFR
* Headset Stereophone: HSOL, HSOR
* Headset Mic: HSMIC (with bias)
* Aux In: AUXL, AUXR
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With this patch the initial headset pop-removal related values are
configured for the twl4030 codec (ramp delay and sysclk).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Connect twl4030 voice DAI to McBSP3 in sdp3430 machine driver.
Voice DAI init function enables corresponding interface by
writting directly to VOICE_IF codec register.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujflausi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Resending the patch after fixing the minor issues.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the four channel TDM mode
on Beagle board.
Depending on the channel count, the interface needs to be
configured differently (I2S for stereo DSP_A for four channels)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add 4 channel support to omap-mcbsp.
This mode is going to be used by the twl4030 codec, when it
is configured in Option1 mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add checking in hw_params and prepare to detect bufferless pcms(i.e. BT
<--> codec).
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add Voice DAI to support the PCM voice interface of the twl4030 codec.
The PCM voice interface can be used with 8-kHz(voice narrowband) or
16-kHz(voice wideband) sampling rates, and 16bits, and mono RX and mono
TX or stereo TX.
The PCM voice interface has two modes
- PCM mode1 : This uses the normal FS polarity and the rising edge of
the clock signal.
- PCM mode2 : This uses the FS polarity inverted and the falling edge
of the clock signal.
If the system master clock is not 26MHz or the twl4030 codec mode is not
option2, the voice PCM interface is not available.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
My email address is going to expire soon so update it. Adding also
Peter Ujfalusi <peter.ujfalusi@nokia.com> as a second contact to OMAP core
drivers since I won't have anymore access to non-public OMAP documentation
in the future and Peter is working with these drivers as well.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DSP_A mode is similar to the DSP_B, but the MSB is delayed with
one bclk (appears after the FS pulse and not under it).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use single-phase mode for the DSP mode and keep the dual phase
mode for the I2S mode.
The mono (1 channel) mode already used single phase mode,
now it is more cleaner. There is no need to configure the
second phase, when the single phase is used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using inverted FS polarity in OSK5912 must be an error since TLV320AIC23
do not have support for inverted polarities. This is mostly due the hassle
with the DSP formats in OMAP McBSP DAI and inversion on OMAP side probably
just made this configuration working at some point.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DSP format wasn't still correct in OMAP McBSP DAI even after the commit
bd25867a6c.
Thanks to Peter Ujfalusi <peter.ujfalusi@nokia.com> for noticing and being
part of the fix. Now the FS length definition is more clear by defining
it with FWID(0).
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (36 commits)
ALSA: hda - Add VREF powerdown sequence for another board
ALSA: oss - volume control for CSWITCH and CROUTE
ALSA: hda - add missing comma in ad1884_slave_vols
sound: usb-audio: allow period sizes less than 1 ms
sound: usb-audio: save data packet interval in audioformat structure
sound: usb-audio: remove check_hw_params_convention()
sound: usb-audio: show sample format width in proc file
ASoC: fsl_dma: Pass the proper device for dma mapping routines
ASoC: Fix null dereference in ak4535_remove()
ALSA: hda - enable SPDIF output for Intel DX58SO board
ALSA: snd-atmel-abdac: increase periods_min to 6 instead of 4
ALSA: snd-atmel-abdac: replace bus_id with dev_name()
ALSA: snd-atmel-ac97c: replace bus_id with dev_name()
ALSA: snd-atmel-ac97c: cleanup registers when removing driver
ALSA: snd-atmel-ac97c: do a proper reset of the external codec
ALSA: snd-atmel-ac97c: enable interrupts to catch events for error reporting
ALSA: snd-atmel-ac97c: set correct size for buffer hardware parameter
ALSA: snd-atmel-ac97c: do not overwrite OCA and ICA when assigning channels
ALSA: snd-atmel-ac97c: remove dead break statements after return in switch case
ALSA: snd-atmel-ac97c: cleanup register definitions
...
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
McBSP2 in OMAP3 has 1 ksample (1k x 32 bit) internal FIFO. During
initial playback startup, this FIFO is keeping the DMA request active
until the FIFO is full.
So now if ALSA buffer size is smaller, DMA is looping around it while
filling up the HW FIFO, generating burst of interrupts as well and SW
doesn't have any change to fill enough data.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Headset was declared previously as a Headphone widget connecting
HSMIC and HSOL/HSOR pins of TWL4030 codec in SDP430 machine driver.
The capture path becomes invalid as the Headphone widget is not a
valid input endpoint.
Instead of that, the Headset is declared as separate Microphone
and Headphone widgets. Current patch modifies audio map:
- Headset Mic: HSMIC with bias
- Headset Stereophone: HSOL, HSOR
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add functions "Headset" and "Mic" to the control "Jack Function" for
activating and de-activating codec input pin LINE1L which is connected to
the mic pin of 4-pole Nokia AV connecter.
Note there is no mic bias voltage management here since bias is coming from
Nokia ASIC and driver for it is not in mainline.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move headset jack registration to the codec/machine specific
initialization. Having the jack registration in machine init
causes that the jack device gets initialized but not registered
since the sound card is registered before the jack. Moving jack
registration to device initialization will register the jack
device along with all other devices associated to the card when
the card is registed. As a consequence of jack device registered
properly, the jack is detected as an input device.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The drivers are basically duplicating the same code over and over.
As snd_soc_cnew is going to be made static some time after the next
merge window, we might as well convert them now.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge Eric Maio's patch to merge snd_soc_dai_ops out of line. Fixed
merge issues and updated drivers, plus an issue with the ops for the two
s3c2443 AC97 DAIs having been merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Buildfix:
CC sound/soc/omap/osk5912.o
sound/soc/omap/osk5912.c: In function 'osk_soc_init':
sound/soc/omap/osk5912.c:189: error: implicit declaration of function 'clk_get_usecount'
make[3]: *** [sound/soc/omap/osk5912.o] Error 1
There's no such (standard) clock interface.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add headset jack detection for SDP3430 boards using SoC jack
reporting interface. Headset detection on SDP3430 board is
achieved through TWL4030 GPIO_2 pin.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Considering the fact that most cpu_dai or codec_dai are using a same
'snd_soc_dai_ops' for several similar interfaces, 'ops' would be better
made a pointer instead, to make sharing easier and code a bit cleaner.
The patch below is rather preliminary since the asoc tree is being
actively developed, and this touches almost every piece of code,
(and possibly many others in development need to be changed as
well). Building of all codecs are OK, yet to every SoC, I didn't test
that.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch replaces "snd_soc_machine" structure by "snd_soc_card" in
SP3430 driver. This change is needed in SDP3430 driver to reflect
changes introduced by "ASoC: Rename snd_soc_card to snd_soc_machine" patch
(875065491f).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
omap_pcm_trigger is called also in interrupt context so CPU flags must
be restored when returning.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update pandora board file for recent TWL4030 codec changes.
Also move output related snd_soc_dapm_nc_pin() calls to
omap3pandora_out_init(), where they belong.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch explicitly initializes McBSP Transmit Configuration
Control Register (XCCR) and Receive Configuration Control
Register (RCCR) to their reset values. Reset values are 26 ns
of DX delay and Transmit DMA disabled for XCCR register;
receive full cycle mode enabled and Receive DMA disabled for
RCCR register.
This patch requires a counterpart in OMAP McBSP driver before
to apply it. The required changes in McBSP were sent and approved
in linux-omap mailing list and patch is going upstream
(commit 3127f8f859 from linux-omap-2.6
tree).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
[ jarkko.nikula@nokia.com: Commit id for counterpart patch corrected ]
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kbuild ignores dependency from things that are themselves selected so
ASoC machine drivers need to ensure that the control bus is being built.
This also avoids issues where multiple buses are supported by a given
codec.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit dc06102a0c in the asoc tree
did not include the necessary Kconfig and Makefile changes. This patch
completes the support for Beagleboard
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PCM operations tables are not exported directly but are instead
included in the platform structure so should be declared static.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pandora has all TWL4030 output pins floating, it uses
external DAC for playback. Mark those outputs as not
connected using DAPM calls.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
N810 bootloader muxes I2S pins for OMAP2420 EAC block while N810 ASoC
drivers are using McBSP block so the kernel have to change configuration
runtime.
Author has not seen problems using kernel pin multiplexing on N810 but very
many times unworking audio after forgotten to enable it and spending
15 minutes each time to figure it out again...
This change makes it easier for other users as well. If problems arise, then
they are better to find and fix in OMAP pin multiplexing framework.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- OMAP McBSP DAI driver claims to support DSP_A format which has 1-bit data
delay but configures link for 0-bit data delay which is in fact DSP_B
- Fix this by changing format from DSP_A to DSP_B
- Fix also TLV320AIC23 codec and OSK5912 machine drivers since the same
error is populated also there
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There will be a Oops or frequent underrun messages when playing music with
omap soc driver, this is because a data region is incorretly sized, other data
region will be overwriten when writing to this data region.
Signed-off-by: Stanley Miao <stanley.miao@windriver.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add snd_ prefix to avoid the conflict of symbols in omac-mcbsp.c:
sound/soc/omap/omap-mcbsp.c:503: error: static declaration of 'omap_mcbsp_init' follows non-static declaration
arch/arm/plat-omap/include/mach/mcbsp.h:373: error: previous declaration of 'omap_mcbsp_init' was here
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is done at modprobe time, mirroring current behaviour, except for
mpc5200_psc_i2s where we do registration at the same time as we register
with soc-of-simple. Since the core currently ignores registration this
has no practical impact.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Register all platform DAIs with the core. In line with current behaviour
this is done at module probe time rather than when the devices are probed
(since currently that only happens as the entire ASoC card is registered
except for those drivers that currently implement some kind of hotplug).
Since the core currently ignores DAI registration this has no practical
effect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds basic support for OMAP3 Pandora.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As part of the deprecation of snd_soc_device push the registration of
the platform down into the card structure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dependency on SND_SOC is already fulfilled in sound/soc/Kconfig,
thus no more need in Kconfig of each sub directory.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch add ASoC support for TI SDP3430. It's based on Gumstix
Overo SoC code by Steve Sakoman.
Signed-off-by: Misael Lopez Cruz <mesak82@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes Kconfig dependency of TWL4030 audio codec driver
with TWL4030 core driver on both overo and omap2evm
boards
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Patch adds support for mono audio links so that McBSP DAI can operate with
real mono codecs. In I2S, the signalling remains the same but only first
frame (left channel) is transmitting audio data and second frame having null
data. In DSP_A, only first frame is transmitted.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Prepare for upcoming McBSP DAI update adding support for mono links by
restricting number of channels to 2 in N810. This is due tlv320aic3x which
claims channels_min = 1 and playing pure mono audio over I2S would cause
it to be played only from left channel if both cpu and codec DAI's claim to
support mono.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAI type information is only ever used within ASoC in order to special
case AC97 and for diagnostic purposes. Since modern CPUs and codecs
support multi function DAIs which can be configured for several modes
it is more trouble than it's worth to maintain anything other than a
flag identifying AC97 DAIs so remove the type field and replace it with
an ac97_control flag.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Peter Ujfalusi