Problem:
ab460a2e72 ("rpmsg: qcom_smd: Access APCS through mailbox framework"
added a "depends on MAILBOX") to RPMSG_QCOM_SMD, thus RPMSG_QCOM_SMD
becomes unset since MAILBOX was not enabled in qcom_defconfig and is
not otherwise selected for the dragonboard. When the resulting
kernel is booted the mmc device which contains the root file system
is not available.
Fix:
add CONFIG_MAILBOX to qcom_defconfig
Fixes: ab460a2e72 ("rpmsg: qcom_smd: Access APCS through mailbox framework"
added a "depends on MAILBOX")
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
IPQ8064 and IPQ4019 boards contain NAND flash
memory for which these configs need to be enabled.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds framebuffer console support to qcom defconfig.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
MSM IOMMU is required for apq8064 display, so enable it by default.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This enables DRM Kconfig for apq8064 display.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Select the options necessary to get USB, coincell, WiFI, touchscreen and
backlight on the Z2 Tablet (and other family B devices) working. The
device specific peripherals are selected as modules.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
GPIO debug spams the kernel log quite a bit, so remove this from the
default Qualcomm defconfig.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable the regulator driver, usb phy drivers, and hsic hub driver
to support USB devices on apq8064 and msm8974.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
CONFIG_HWSPINLOCK must be selected explicitly for SMEM and its
dependencies to be enabled.
The update is generated by "make savedefconfig" and as such reflects
changes to the implicit state of other options, as of v4.14-rc1.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
* Enable RPMSG_QCOM_SMD to get boards working again
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wPTI
-----END PGP SIGNATURE-----
Merge tag 'qcom-defconfig-for-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/defconfig
Pull "Qualcomm ARM Based defconfig Updates for v4.13 - Part 2" from Andy Gross:
* Enable RPMSG_QCOM_SMD to get boards working again
* tag 'qcom-defconfig-for-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: qcom_defconfig: enable RPMSG_QCOM_SMD
As of commit 5052de8def, QCOM_SMD_RPM and various other config
options enabled in the qcom_defconfig depends on the RPMSG. If
QCOM_SMD_RPM config option is not selected it disables the
REGULATOR_QCOM_SMD_RPM and other essential config options.
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
1. Remove old Kconfig options from all ARM configs,
2. Update Samsung defconfigs to bring back options over time got disabled
for some reason (configs were not updated along with the code),
3. Save defconfigs for Samsung.
-----BEGIN PGP SIGNATURE-----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=uKGf
-----END PGP SIGNATURE-----
Merge tag 'samsung-defconfig-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/defconfig
Pull "ARM defconfig cleanup" from Krzysztof Kozłowski:
1. Remove old Kconfig options from all ARM configs,
2. Update Samsung defconfigs to bring back options over time got disabled
for some reason (configs were not updated along with the code),
3. Save defconfigs for Samsung.
* tag 'samsung-defconfig-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: tct_hammer_defconfig: Save defconfig
ARM: s5pv210_defconfig: Save defconfig
ARM: s3c6400_defconfig: Save defconfig
ARM: mini2440_defconfig: Save defconfig
ARM: s3c2410_defconfig: Save defconfig
ARM: exynos_defconfig: Save defconfig
ARM: s5pv210_defconfig: Bring back lost (but wanted) options
ARM: s3c6400_defconfig: Bring back lost (but wanted) options
ARM: s3c2410_defconfig: Bring back lost (but wanted) options
ARM: tct_hammer_defconfig: Bring back lost (but wanted) options
ARM: mini2440_defconfig: Bring back lost (but wanted) options
ARM: defconfig: samsung: Re-order entries to match savedefconfig
ARM: defconfig: Cleanup from old Kconfig options
These configs are required for booting kernel in QCOM IPQ4019 boards.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
An adsp-pil node is present in at least the MSM8974 SoC. Simply enable
all Qualcomm remoteproc drivers to avoid more work in the future.
The SMP2P driver is required for adsp-pil to initialize correctly.
Enable the SMSM driver at Bjorn Andersson's request: "We also need
CONFIG_QCOM_SMSM=y here, its currently used to signal state of the ring
buffers for WiFi."
CONFIG_QCOM_WCNSS_CTRL is required to load firmware/configuration data
into the WCNSS core, which handles WiFi and Bluetooth.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This default-enables the devices found on the APQ8060 DragonBoard
in the qcom_defconfig:
- EBI2 bus
- SMSC911x ethernet
- LEDs class and PM8058 LEDs driver, trigger and heartbeat
trigger (so we get heartbeat on the board by default)
- IIO framework, including the HRTimer trigger, KXSD9
accelerometer, MPU3050 gyroscope, AK8975 magnetometer and
BMP085 pressure sensor
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables thermal sensors and QFPROM support for qcom platforms.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables configs required to get SATA functionality working on
IFC6410 board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
IFC6410 board has PCIE based ATL1C ethernet controller, so enable related configs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable support for clocks, controlled by the RPM processor on
Qualcomm platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Defconfig additions, removals, etc. Most of these are small changes adding
the options for newly upstreamed drivers, or drivers needed for new board
support.
Bartlomiej Zolnierkiewicz has done a series of patches reducing the use
of CONFIG_IDE from 19 to 3 in favor of CONFIG_ATA.
Overall more patches than usual, but nothing big.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2XsL
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"Defconfig additions, removals, etc. Most of these are small changes
adding the options for newly upstreamed drivers, or drivers needed for
new board support.
Bartlomiej Zolnierkiewicz has done a series of patches reducing the
use of CONFIG_IDE from 19 to 3 in favor of CONFIG_ATA.
Overall more patches than usual, but nothing big"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: davinci_all_defconfig: Enable da8xx usb otg
ARM: defconfig: drop GPIO_SYSFS on multiplatforms
ARM: multi_v7_defconfig: enable STMicroelectronics HVA driver
ARM: configs: Add new config fragment to change RAM start point
ARM: davinci_all_defconfig: Enable OHCI as module
ARM: defconfig: turn on the DT cpufreq for Integrator
ARM: omap2plus_defconfig: Run make savedefconfig to save some space
ARM: davinci_all_defconfig: add missing options for systemd
ARM: davinci_all_defconfig: enable the mstpri and ddrctl drivers
ARM: bcm2835: add thermal driver to default config
ARM: omap2plus_defconfig: Enable LP873X support
ARM: omap2plus_defconfig: Enable REGULATOR_GPIO
ARM: omap2plus_defconfig: Enable TOUCHSCREEN_TSC2004
ARM: socfpga_defconfig: enable FS configs to support Angstrom filesystem
ARM: config: Enable GPIO Key driver in stm32_defconfig
ARM: tegra: Enable GMI driver in default configuration
ARM: tegra: Enable SGTL5000 audio
ARM: tegra: Update default configuration for v4.9-rc1
ARM: socfpga: updates for socfpga_defconfig
ARM: davinci_all_defconfig: enable LED default-on trigger
...
The Kconfig and file naming for the PM8xxx driver is totally
confusing:
- Kconfig options MFD_PM8XXX and MFD_PM8921_CORE, some in-kernel
users depending on or selecting either at random.
- A driver file named pm8921-core.c even if it is indeed
used by the whole PM8xxx family of chips.
- An irqchip named pm8xxx since it was (I guess) realized that
the driver was generic for all pm8xxx PMICs.
As I may want to add support for PM8901 this is starting to get
really messy. Fix this situation by:
- Remove the MFD_PM8921_CORE symbol and rely solely on MFD_PM8XXX
and convert all users, including LEDs Kconfig and ARM defconfigs
for qcom and multi_v7 to use that single symbol.
- Renaming the driver to qcom-pm8xxx.c to fit along the two
other qcom* prefixed drivers.
- Rename functions withing the driver from 8921 to 8xxx to
indicate it is generic.
- Just drop the =m config from the pxa_defconfig, I have no clue
why it is even there, it is not a Qualcomm platform. (Possibly
older Kconfig noise from saveconfig.)
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
After enabling this I get pins, GPIO, keys and everything on
the MSM8660 surf (APQ8660 DragonBoard).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable some ssbi drivers present on msm8660, msm8960 and apq8064
devices so that we fully exercise the devices present in the dts
files.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This enables smem, smd, rpm, regulators, pmic pinctrl and hwspinlock as
these platform features are now merged. It enables gpio-keys as this is
used by most boards and enables fhandle and cgroups, so we can boot
systemd.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable this config in the defconfig so that we can delete the
selection logic surrounding it that exists in mach-qcom/Kconfig.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Enable the RPM and RPM regulator drivers as well as the KS8851
ethernet driver so that ethernet works on MSM8960 CDP.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
There are currently more than 16 partitions on the eMMC of all recent
Qualcomm devices. Increase the number of minors per block device to
detect all available partitions.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
After removing ARCH_REQUIRE_GPIOLIB we need to select
CONFIG_GPIOLIB to keep building the pinctrl drivers. Make the
defconfig smaller too by running savedefconfig.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Enable the LPASS clock controller driver so that audio drivers
can enable, disable, and set rates on their clocks.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
[sboyd@codeaurora.org: Enable 8960 driver too]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
* General defconfig update to match upstream changes
* Enable IPQ806x & APQ8084 clk support
* Enable pinctrl on MSM8960
* Enable CPU_IDLE to get basic wfi support
* Enable SPI NOR and MTD M25P80 support (used on AP148 board)
* Enable SATA PHY support on IPQ806x and APQ8064
* Enable Fixed regulator and ARM MMCI support (mmc support on APQ8064)
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add a defconfig for mach-qcom platforms (copied from msm_defconfig).
Although these platforms are part of the multi-platform kernel, it's
useful to have a stripped down version of the defconfig that just
selects the DT based Qualcomm platforms and drivers.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>