This patch adds a member (cpu_pwr_sample_ratio) of fam15h_power_data,
that represents the ratio of compute unit power accumulator sample
period to the PTSC counter period.
Tsample: compute unit power accumulator sample period
Tref: the performance timestamp counter period
PTSC: performance timestamp counter
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On Carrizo and later platforms, running_avg_capture bit field is
extended to 4:31 (28 bits) from 4:25.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We rename fam15h_power_is_internal_node0() function to
should_load_on_this_node(), because it may not be node0 from KV and
on, and they are single-node processors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
AMD Carrizo(Fam15h, M60h) processors can report power1_crit
(ProcessorPwrWatts) and power1_input (CurrPwrWatts) values.
And this patch adds support for CZ.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the LTC chips supported by this driver have to be polled
to ensure that they are ready to accept commands.
Signed-off-by: Michael Jones <mike@proclivis.com>
[Guenter Roeck: simplifications and formatting changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PMBus controllers optionally support PEC. Configure the driver
to use it if available to improve operational security.
Suggested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3886 is a is a dual PolyPhase DC/DC synchronous step-down switching
regulator controller. It is mostly command compatible to LTC3883,
but supports two phases instead of one.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2980 and LTM2987 are command compatible to LTC2977. They consist of
two LTC2977 on a single die, and are instantiated as two separate chips,
each supporting eight channels.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add additional chip ID for an older revision of LTC2978, as well
as two chip IDs for LTC3882. Turns out the LTC3882 does support the
LTC2978_MFR_SPECIAL_ID register, and reading it returns its chip ID,
but the register is undocumented.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per information from Linear Technologies, the ID mask is 12 bit
for all chips of this series. Use this mask to detect chips to ensure
that all chip revisions are detected.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The code used to determine historic low and high peaks is repeated
several times. Introduce helper functions to simplify it.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is becoming cumbersom to track per-chip feature support.
Introduce feature flag to simplify the code.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2975 is mostly compatible to LTC2974, but supports input current
and power measurement.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per datasheet, the chip ID for LTM4676 is 0x448x. This was observed
in real systems. In addition to that, chip ID 0x4401 was observed
as well. Research shows that the chip ID has been changed from 0x440x
to 0x448x in datasheet revision C. Add support for the additional chip ID.
Also add the chip ID for LTM4676A, which is functionally identical
to LTM4676.
Reported-by: Ananda Babu Nettam <anandab@juniper.net>
Cc: Ananda Babu Nettam <anandab@juniper.net>
Cc: Amit U Jain <amjain@juniper.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3882 is mostly compatible with LTC3880. Major differences are that it
does not measure the input current, and it no longer supports LTC's legacy
mechanism to identify the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Verifying the chip type is getting more complicated with new chips,
since not all chips support the same mechanism to read the chip type.
Move the code into a separate function to simplify adding support for
those chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This change sht15_reverse() to be generic bitrev8().
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add device IDs and references for Texas Instruments TPS544B20, TPS544B25,
TPS544C20, and TPS544C25 to the generic PMBus driver.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX20751 is a multiphase power controller with internal buck converter.
It uses VR12.0 to report the output voltage. This requires an explicit
driver, since the VR version can not be auto-detected.
The chip supports a manufacturer specific command to fine-tune the output
voltage. This command is not currently supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the IT8732F. This chip is pretty similar to IT8721F,
with the main difference being that the ADC LSB is 10.9 mV instead of
12 mV.
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADM1293 and ADM1294 are mostly compatible with other chips of the same
series, but have more configuration options. There are also some
differences in register details.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Introduce have_vout, have_vaux_status, have_pin_max, and have_uc_fault
to simplify adding support for new chips.
Also simplify error returns where appropriate to return immediately
on error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Each new chip supported by the driver has a new set of coefficients,
making hard-coding coefficients more and more cumbersome. Introduce
a datastructure and table to simplify configuration.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_regulator_ops is not modified after initialized, so make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pmbus_regulator_ops is for voltage regulators, so explicitly set
regulator type for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add f81768d (id 0x1210) currently found on Jetway motherboards.
It has 11 voltages but otherwise needed no special handling
in this driver.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The temperature value of Fintek F81866 is the same with
f71882fg. It located with 0x6c + 2*(nr), others located
with 0x6c + 2*(nr+1). We change the rule in f71882fg_probe(),
If type = f71858fg/f8000/f81866a. the temp_start will set to 0,
others are 1.
The F81866 over-temperature beep setting is not the same with
f71882fg too. They are using the same address 63H, but F81866 is
using bit 0/1/2 & 4/5/6, others are using bit 1/2/3 & 5/6/7,
So we copy from fxxxx_temp_beep_attr[] to f81866_temp_beep_attr
and change bit setting.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add New Fintek SuperIO F81866(0x1010) & F71868(0x1106)
with H/W Monitor functions.
We increased F71882FG_MAX_INS from 9 to 10 to read
F71868 10 voltage sets.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added fan output control registers.
Modes of operation are PWM (default) and DC.
Introduced show_pwm, store_pwm, nct7802_pwm_attrs, nct7802_pwm_group.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CPU fan speed going up and down on Dell Studio XPS 8100 for
unknown reasons. Without further debugging on the affected
machine, it is not possible to find the problem.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100121
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Jan C Peters <jcpeters89@gmail.com>
Cc: stable@vger.kernel.org # v4.0+, will need backport
[groeck: cleaned up description, comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writing a large value into a voltage limit attribute can result
in an overflow due to an auto-conversion from unsigned long to
unsigned int.
Cc: Constantine Shulyupin <const@MakeLinux.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm attributes have well defined names, which should be used.
Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Cc: stable@vger.kernel.org #v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Huang Rui