Fixes htmldocs warning:
Warning(mac80211.h:379): No description found for parameter 'pad[2]'
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is necessary in order to provide a proper Access point support for p54.
Unfortunately for us, there is no documented way to disable the interfering
power save buffering mechanism in firmware completely.
Therefore we give in and notify the driver through our new sta_notify_ps callback,
so that we can update the filter state.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new NL80211_CMD_SET_WIPHY attributes
NL80211_ATTR_WIPHY_FREQ and NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET to allow
userspace to set the operating channel (e.g., hostapd for AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, the BUILD_BUG_ON calls in ieee80211_tx_info_clear_status can
fail on some architectures.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete kernel-doc struct descriptions for fields that don't exist:
Warning(include/net/mac80211.h:1263): Excess struct/union/enum/typedef member 'conf_ht' description in 'ieee80211_ops'
Warning(net/mac80211/sta_info.h:309): Excess struct/union/enum/typedef member 'addr' description in 'sta_info'
Warning(net/mac80211/sta_info.h:309): Excess struct/union/enum/typedef member 'aid' description in 'sta_info'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Johannes Berg <johannes@sipsolutions.net>
cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On ARM alignment is done slightly different from other architectures.
struct ieee80211_tx_rate is aligned to word size, even though it only has 3
single-byte members, which triggers the BUILD_BUG_ON in
ieee80211_tx_info_clear_status
This patch marks the struct ieee80211_tx_rate as packed, so that ARM
behaves like the other architectures.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before ieee80211_notify_mac() was added, it was presented with the
use case of using it to tell mac80211 that the association may
have been lost because the firmware crashed/reset.
Since then, it has also been used by iwlwifi to (slightly) speed
up re-association after resume, a workaround around the fact that
mac80211 has no suspend/resume handling yet. It is also not used
by any other drivers, so clearly it cannot be necessary for "good
enough" suspend/resume.
Unfortunately, the callback suffers from a severe problem: It only
works for station mode. If suspend/resume happens while in IBSS or
any other mode (but station), then the callback is pointless.
Recently, it has created a number of locking issues, first because
it required rtnl locking rather than RCU due to calling sleeping
functions within the critical section, and now because it's called
by iwlwifi from the mac80211 workqueue that may not use the rtnl
because it is flushed under rtnl.
(cf. http://bugzilla.kernel.org/show_bug.cgi?id=12046)
I think, therefore, that we should take a step back, remove it
entirely for now and add the small feature it provided properly.
For suspend and resume we will need to introduce new hooks, and for
the case where the firmware was reset the driver will probably
simply just pretend it has done a suspend/resume cycle to get
mac80211 to reprogram the hardware completely, not just try to
connect to the current AP again in station mode. When doing so, we
will need to take into account locking issues and possibly defer
to schedule_work from within mac80211 for the resume operation,
while the suspend operation must be done directly.
Proper suspend/resume should also not necessarily try to reconnect
to the current AP, the time spent in suspend may have been short
enough to not be disconnected from the AP, mac80211 will detect
that the AP went out of range quickly if it did, and if the
association is lost then the AP will disassoc as soon as a data
frame is sent. We might also take into account WWOL then, and
have mac80211 program the hardware into such a mode where it is
available and requested.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send a notification to the driver on succesful
reception of an ADDBA response, add IEEE80211_AMPDU_TX_RESUME
for this purpose.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the SSID from the driver API since now there is no
driver that requires knowing the SSID and I think it's
unlikely that any hardware design that does require the
SSID will play well with mac80211.
This also removes support for setting the SSID in master
mode which will require a patch to hostapd to not try.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One parameter wasn't described and one I forgot to update when
renaming it; also update TBDs in sta_info.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless HW without any dedicated queues for aggregation
do not need the ampdu_queues mechanism present right now
in mac80211. Since mac80211 is still incomplete wrt TX MQ
changes, do not allow aggregation sessions for drivers that
set ampdu_queues.
This is only an interim hack until Intel fixes the requeue issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct a handful of errors found while reading the mac80211 book.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"Clearing" the rate control algorithm is pointless, none of
the algorithms actually uses this operation and it's not even
invoked properly for all channel switching. Also, there's no
need to since rate control algorithms work per station.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HT handling has the following deficiencies, which I've
(partially) fixed:
* it always uses the AP info even if there is no AP,
hence has no chance of working as an AP
* it pretends to be HW config, but really is per-BSS
* channel sanity checking is left to the drivers
* it generally lets the driver control too much
HT enabling is still wrong with this patch if you have more than
one virtual STA mode interface, but that never happens currently.
Once WDS, IBSS or AP/VLAN gets HT capabilities, it will also be
wrong, see the comment in ieee80211_enable_ht().
Additionally, this fixes a number of bugs:
* mac80211: ieee80211_set_disassoc doesn't notify the driver any
more since the refactoring
* iwl-agn-rs: always uses the HT capabilities from the wrong stuff
mac80211 gives it rather than the actual peer STA
* ath9k: a number of bugs resulting from the broken HT API
I'm not entirely happy with putting the HT capabilities into
struct ieee80211_sta as restricted to our own HT TX capabilities,
but I see no cleaner solution for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move bss_conf into the vif struct so that drivers can
access it during ->tx without having to store it in
the private data or similar. No driver updates because
this is only for when they want to start using it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 notify the driver which configuration
actually changed, e.g. channel etc.
No driver changes, this is just plumbing, driver authors are
expected to act on this if they want to.
Also remove the HW CONFIG debug printk, it's incorrect, often
we configure something else.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up a number of things:
* the unusable definition of the HT capabilities/HT information
information elements
* variable names that are hard to understand
* mac80211: move ieee80211_handle_ht to ht.c and remove the unused
enable_ht parameter
* mac80211: fix bug with MCS rate 32 in ieee80211_handle_ht
* mac80211: fix bug with casting the result of ieee80211_bss_get_ie
to an information element _contents_ rather than the
whole element, add size checking (another out-of-bounds
access bug fixed!)
* mac80211: remove some unused return values in favour of BUG_ON
checking
* a few minor other things
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 handle short slot requests from the AP
properly. Also warn about uses of IEEE80211_CONF_SHORT_SLOT_TIME
and optimise out the code since it cannot ever be hit anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The antenna gain isn't exactly configurable, despite the belief of
some unnamed individual who thinks that the EEPROM might influence
it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This isn't used by anyone, if we ever need it we can add
it back, until then it's useless.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix mac80211.h kernel-doc: it had some extra parameters that were
no longer valid and incorrect format for a return value in 2 places.
Warning(lin2628-rc2//include/net/mac80211.h:1487): Excess function parameter or struct member 'control' description in 'ieee80211_beacon_get'
Warning(lin2628-rc2//include/net/mac80211.h:1596): Excess function parameter or struct member 'control' description in 'ieee80211_get_buffered_bc'
Warning(lin2628-rc2//include/net/mac80211.h:1632): Excess function parameter or struct member 'rc4key' description in 'ieee80211_get_tkip_key'
Warning(lin2628-rc2//include/net/mac80211.h:1735): Excess function parameter or struct member 'return' description in 'ieee80211_start_tx_ba_session'
Warning(lin2628-rc2//include/net/mac80211.h:1775): Excess function parameter or struct member 'return' description in 'ieee80211_stop_tx_ba_session'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix kernel-doc warnings in mac80211.h.
Fields need real explanations added to them.
Warning(lin2627-g3-kdocfixes//include/net/mac80211.h:659): No description found for parameter 'icv_len'
Warning(lin2627-g3-kdocfixes//include/net/mac80211.h:659): No description found for parameter 'iv_len'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adjusts the rate control API to allow multi-rate retry
if supported by the driver. The ieee80211_hw struct specifies how
many alternate rate selections the driver supports.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free up 2 bytes in skb->cb to be used for multi-rate retry later.
Move iv_len and icv_len initialization into key alloc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Long awaited, hard work. This patch totally cleans up the rate control
API to remove the requirement to include internal headers outside of
net/mac80211/.
There's one internal use in the PID algorithm left for mesh networking,
we'll have to figure out a way to clean that one up and decide how to
do the peer link evaluation, possibly independent of the rate control
algorithm or via new API.
Additionally, ath9k is left using the cross-inclusion hack for now, we
will add new API where necessary to make this work properly, but right
now I'm not expert enough to do it. It's still off better than before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, virtual interface pointers passed to drivers might be
from monitor interfaces and as such completely uninitialised
because we do not tell the driver about monitor interfaces when
those are created. Instead of passing them, we should therefore
indicate to the driver that there is no information; do that by
passing a NULL value and adjust drivers to cope with it.
As a result, some mac80211 API functions also need to cope with
a NULL vif pointer so drivers can still call them unconditionally.
Also, when injecting frames we really don't want to pass NULL all
the time, if we know we are the source address of a frame and have
a local interface for that address, we can to use that interface.
This also helps with processing the frame correctly for that
interface which will help the 802.11w implementation. It's not
entirely correct for VLANs or WDS interfaces because there the MAC
address isn't unique, but it's already a lot better than what we
do now.
Finally, when injecting without a matching local interface, don't
assign sequence numbers at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rate control algorithms may need access to a station's
HT capabilities, so share the ht_info struct in the
public station API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As more preparation for a saner rate control algorithm API,
share the supported rates bitmap in the public API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211 to share some more data about
stations with drivers. Should help iwlwifi and ath9k when
they get around to updating, and might also help with
implementing rate control algorithms without internals.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers need to know the basic rateset to be able to configure
the ACK/CTS programming in hardware correctly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove an interface, we can currently end up having
a pointer to it left in local->scan_sdata after it has been
set down, and then with a hardware scan the scan completion
can try to access it which is a bug. Alternatively, a scan
that started as a hardware scan may terminate as though it
was a software scan, if the timing is just right.
On SMP systems, software scan also has a similar problem,
just canceling the delayed work and setting a flag isn't
enough since it may be running concurrently; in this case
we would also never restore state of other interfaces.
This patch hopefully fixes the problems by always invoking
ieee80211_scan_completed or requiring it to be invoked by
the driver, I suspect the drivers that have ->hw_scan() are
buggy. The bug will not manifest itself unless you remove
the interface while hw-scanning which will also turn off
the hw, and then add a new interface which will be unusable
until you scan once.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the new wireless regulatory infrastructure. The
main motiviation behind this was to centralize regulatory
code as each driver was implementing their own regulatory solution,
and to replace the initial centralized code we have where:
* only 3 regulatory domains are supported: US, JP and EU
* regulatory domains can only be changed through module parameter
* all rules were built statically in the kernel
We now have support for regulatory domains for many countries
and regulatory domains are now queried through a userspace agent
through udev allowing distributions to update regulatory rules
without updating the kernel.
Each driver can regulatory_hint() a regulatory domain
based on either their EEPROM mapped regulatory domain value to a
respective ISO/IEC 3166-1 country code or pass an internally built
regulatory domain. We also add support to let the user set the
regulatory domain through userspace in case of faulty EEPROMs to
further help compliance.
Support for world roaming will be added soon for cards capable of
this.
For more information see:
http://wireless.kernel.org/en/developers/Regulatory/CRDA
For now we leave an option to enable the old module parameter,
ieee80211_regdom, and to build the 3 old regdomains statically
(US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY.
These old static definitions and the module parameter is being
scheduled for removal for 2.6.29. Note that if you use this
you won't make use of a world regulatory domain as its pointless.
If you leave this option enabled and if CRDA is present and you
use US or JP we will try to ask CRDA to update us a regulatory
domain for us.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The conf_tx callback currently needs to be atomic, this requirement
is just because it can be called from scanning. This rearranges it
slightly to only update while not scanning (which is fine, we'll be
getting beacons when associated) and thus removes the atomic
requirement.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change adds a new cfg80211 command, NL80211_CMD_SET_BSS, to allow
AP mode BSS parameters to be changed from user space (e.g., hostapd).
The drivers using mac80211 are expected to be modified with separate
changes to use the new BSS info parameter for short slot time in the
bss_info_changed() handler.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All users have been moved over to the version taking a le16 frame control
rather than a cpu-endian value.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds ieee80211_queue_stopped that let drivers to query
queue status
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE was made unnecessary in
the recent revamp on beacon configuration.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes possible for a driver to specify maximal listen interval
The possibility for user to configure listen interval is not implemented
yet, currently the maximum provided by the driver or 1 is used.
Mac80211 uses config handler to set listen interval for to the driver.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the dtim_period in ieee80211_bss_conf, this allows the low
level driver to know the dtim_period, and to plan power save accordingly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot this in the previous patch that made it unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only behavior change is that we do not drop packets under any
circumstances. If that is absolutely needed, we could easily add it
back.
With cleanups and help from Johannes Berg.
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple issues:
- there are no "default" values needed
- cw_min/cw_max can be larger than documented
- restructure to decrease size
- use get_unaligned_le16
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.
This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.
It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements the power management routines wireless extensions
for mac80211.
For now we only support switching PS mode between on and off.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix more than 50 kernel-doc warnings in ieee80211/mac80211 kernel-doc notation.
Fix a few typos also.
Note: Some fields are marked as TBD and need to have their description
corrected.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds block ack request capability
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add spectrum capability and required information
elements to association request providing AP has requested it and
it is supported by the driver
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 refuse a WEP key whose length is not WEP40 nor
WEP104.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The workqueue provided by mac80211 should not be used for
scheduled tasks that acquire the RTNL lock. This could be done
when the driver uses the function ieee80211_iterate_active_interfaces()
within the scheduled work. Such behavior will end in locking
dependencies problems when an interface is being removed.
This patch will add a notification about the RTNL locking and
the mac80211 workqueue to prevent driver developers from
blindly using it.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers may want to to use the TKIP key offsets for TX and RX
MIC so lets move this out. Lets also clear up a bit how this is used
internally in mac80211.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take a __le16 directly rather than a host-endian value.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates mac80211 and drivers to be multi-queue aware and
use that instead of the internal queue mapping. Also does a number
of cleanups in various pieces of the code that fall out and reduces
internal mac80211 state size.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There really is no reason for a driver to reject a frame on
an A-MPDU queue when it can stop that queue for any period
of time and is given frames one by one. Hence, disallow it
with a big warning and reduce mac80211-internal state.
Also add a warning when we try to fragment a frame destined
for an A-MPDU queue and drop it, the actual bug needs to be
fixed elsewhere but I'm not exactly sure how to yet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies struct ieee80211_tx_control to give band
info and the rate index (instead of rate pointers) to drivers.
This mostly serves to reduce the TX control structure size to
make it fit into skb->cb so that the fragmentation code can
put it there and we can think about passing it to drivers that
way in the future.
The rt2x00 driver update was done by Ivo, thanks.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having drivers start queues is just confusing, their ->start()
callback can block and do whatever is necessary, so let mac80211
start queues and have drivers wake queues when necessary (to get
packets flowing again right away.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit e38bad4766
mac80211: make ieee80211_iterate_active_interfaces not need rtnl
rt2500usb and rt73usb broke down due to attempting register access
in atomic context (which is not possible for USB hardware).
This patch restores ieee80211_iterate_active_interfaces() to use RTNL lock,
and provides the non-RTNL version under a new name:
ieee80211_iterate_active_interfaces_atomic()
So far only rt2x00 uses ieee80211_iterate_active_interfaces(), and those
drivers require the RTNL version of ieee80211_iterate_active_interfaces().
Since they already call that function directly, this patch will automatically
fix the USB rt2x00 drivers.
v2: Rename ieee80211_iterate_active_interfaces_rtnl
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
trying to clean up the signal/noise code. the previous code in mac80211 had
confusing names for the related variables, did not have much definition of
what units of signal and noise were provided and used implicit mechanisms from
the wireless extensions.
this patch introduces hardware capability flags to let the hardware specify
clearly if it can provide signal and noise level values and which units it can
provide. this also anticipates possible new units like RCPI in the future.
for signal:
IEEE80211_HW_SIGNAL_UNSPEC - unspecified, unknown, hw specific
IEEE80211_HW_SIGNAL_DB - dB difference to unspecified reference point
IEEE80211_HW_SIGNAL_DBM - dBm, difference to 1mW
for noise we currently only have dBm:
IEEE80211_HW_NOISE_DBM - dBm, difference to 1mW
if IEEE80211_HW_SIGNAL_UNSPEC or IEEE80211_HW_SIGNAL_DB is used the driver has
to provide the maximum value (max_signal) it reports in order for applications
to make sense of the signal values.
i tried my best to find out for each driver what it can provide and update it
but i'm not sure (?) for some of them and used the more conservative guess in
doubt. this can be fixed easily after this patch has been merged by changing
the hardware flags of the driver.
DRIVER SIGNAL MAX NOISE QUAL
-----------------------------------------------------------------
adm8211 unspec(?) 100 n/a missing
at76_usb unspec(?) (?) unused missing
ath5k dBm dBm percent rssi
b43legacy dBm dBm percent jssi(?)
b43 dBm dBm percent jssi(?)
iwl-3945 dBm dBm percent snr+more
iwl-4965 dBm dBm percent snr+more
p54 unspec 127 n/a missing
rt2x00 dBm n/a percent rssi+tx/rx frame success
rt2400 dBm n/a
rt2500pci dBm n/a
rt2500usb dBm n/a
rt61pci dBm n/a
rt73usb dBm n/a
rtl8180 unspec(?) 65 n/a (?)
rtl8187 unspec(?) 65 (?) noise(?)
zd1211 dB(?) 100 n/a percent
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This
* makes the queue number passed to drivers a u16
(as it will be with skb_get_queue_mapping)
* removes the useless queue number defines
* splits hw->queues into hw->queues/ampdu_queues
* removes the debugfs files for per-queue counters
* removes some dead QoS code
* removes the beacon queue configuration for IBSS
so that the drivers now never get a queue number
bigger than (hw->queues + hw->ampdu_queues - 1)
for tx and only in the range 0..hw->queues-1 for
conf_tx.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue info in struct ieee80211_tx_status is never used.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback takes a ieee80211_tx_queue_stats with a contained
array of ieee80211_tx_queue_stats_data, remove the former, rename
the latter to ieee80211_tx_queue_stats and make tx_stats() take
the array directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a new flag to the ieee80211_key_conf structure.
This flag will inform the driver the key is pairwise rather then
a shared key.
This is important for drivers who support both types of keys,
and need to be informed which type of key this is. Alternative
would be drivers checking the address argument of set_key(),
but it will be safer when mac80211 is more explicit.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hw_key_idx inside the ieee80211_key_conf structure does
not provide all the information drivers might need to perform
hardware encryption.
This is in particular true for rt2x00 who needs to know the
key algorithm and whether it is a shared or pairwise key.
By passing the ieee80211_key_conf pointer it assures us that
drivers can make full use of all information that it should know
about a particular key.
Additionally this patch updates all drivers to grab the hw_key_idx from
the ieee80211_key_conf structure.
v2: Removed bogus u16 cast
v3: Add warning about ieee80211_tx_control pointers
v4: Update warning about ieee80211_tx_control pointers
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to send BSS changes to driver from beacons processed
during scanning. We are more interested in beacons from an AP with which
we are associated - these will still be used to send updates to driver as
the beacons are received without scanning.
This change·removes the requirement that bss_info_changed needs to be atomic.
The beacons received during scanning are processed from a tasklet, but if we
do not call bss_info_changed for these beacons there is no need for it to be
atomic. This function (bss_info_changed) is called either from workqueue or
ioctl in all other instances.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new API to MAC80211 to allow low level driver to
notify MAC with driver status.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is necessary for the upcoming Accesspoint patch for p54.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds assocation capability, timestamp (tsf) and beacon interval
to bss_conf. This is required for successful assocation of iwlwifi drivers
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch eliminates the use of conf_ht, replacing it with
bss_info_changed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 able to send a phase1 key for TKIP
decryption.
This is needed for drivers that don't do the rekeying by themselves
(i.e. iwlwifi). Upon IV16 wrap around, the packet is decrypted in SW,
if decryption is ok, mac80211 calls to update_tkip_key with a new
phase 1 RX key.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 able to compute a TKIP key from an skb.
The requested key can be a phase 1 or a phase 2 key.
This is useful for drivers who need to provide tkip key to their
HW to enable HW encryption.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch clarifies the use of IEEE80211_TXCTL_OFDM_HT flag.
Can by united with patch "mac80211: adding mac80211_tx_control
flags and HT flags"
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes enum from the defines previously dwelled inside
ieee80211_tx_control for better readability.
The patch also addes HT flags, for 802.11n drivers:
- IEEE80211_TXCTL_OFDM_HT: request low-level driver to use HT OFDM rates
- IEEE80211_TXCTL_GREEN_FIELD: use green field protection
- IEEE80211_TXCTL_DUP_DATA: duplicate data on both 20 Mhz channels
- IEEE80211_TXCTL_40_MHZ_WIDTH: send this frame in 40Mhz width
- IEEE80211_TXCTL_SHORT_GI: send this frame with short guard interval
Tx command can be a combination of any of these flags, along with
bitrate represented by ieee80211_rate. this will allow legacy drivers to
switch easily to any 11n rate representation.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Quite a while ago I started this book. The required kernel-doc
patches have since gone into the tree so it is now possible to
build the book in mainline.
The actual documentation is still rather incomplete and not all
things are linked into the book, but this enables us to edit
the documentation collaboratively, hopefully driver authors can
add documentation based on their experience with mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various cleanups, reducing the #ifdef mess and other things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch clarifies the use of the irqsafe vs. non-irq-safe
functions and their respective locking requirements.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the code for TX filtered frames, splitting it out to
a new function to handle those cases, making the clear instruction
a flag and renaming a few things to be easier to understand and
less Atheros hardware specific. Finally, it also makes the comments
explain more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enable IBSS cell merging. if an IBSS beacon with the same channel, same ESSID
and a TSF higher than the local TSF (mactime) is received, we have to join its
BSSID. while this might not be immediately apparent from reading the 802.11
standard it is compliant and necessary to make IBSS mode functional in many
cases. most drivers have a similar behaviour.
* move the relevant code section (previously only containing debug code) down
to the end of the function, so we can reuse the bss structure.
* we have to compare the mactime (TSF at the time of packet receive) rather
than the current TSF. since mactime is defined as the time the first data
symbol arrived we add the time until byte 24 where the timestamp resides, since
this is how the beacon timestamp is defined. as some some drivers are not able
to give a reliable mactime we fall back to use the current TSF, which will be
enough to catch most (but not all) cases where an IBSS merge is necessary.
* in IBSS mode we want to allow beacons to override probe response info so we
can correctly do merges.
* we don't only configure beacons based on scan results, so change that
message.
* to enable this we have to let all beacons thru in IBSS mode, even if they
have a different BSSID.
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
define mactime as the time when the first data symbol arrived at the HW. the
old definition was questionable because 802.11 defines timestamp only for
beacon and probe response frames, and there it means the timestamp field.
a stricter definition of mactime is necessary for correct merging of IBSS.
note that it is up to the driver to convert whatever its hardware returns to
this definition. unfortunately we don't know for example when atheros hardware
takes its rx timestamp exactly :(
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This extends the filter flags documentation to make it clear
what clearing a flag really means.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes mac80211 to pass the burst time to conf_tx in txop
units rather than 0.1msec units. 0.1msec units are only required
by atheros hardware (according to current driver support), all
other drivers do other calculations or require the txop value.
Therefore, it results in fewer calculations and more precision
if we just pass the txop value through to the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds fields to ieee80211_tx_status in order to allow block ack
information exchange between low-level driver,mac80211 and rate scaling
module.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows qdisc support in A-MPDU Tx. a method to
handle QoS <-> TID switches is present in this patch.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the API for 3 stages in A-MPDU Tx session flow:
- request mac80211 to start/stop A-MPDU Tx session for specific TID. such a
request should be issued by a load aware element, either mac80211 itself
or external element.
- requests by mac80211 to low-level driver to start/stop Tx aggregation.
notice that low level driver responds now with Starting Sequence Number.
- async feedback by low-level to mac80211 to inform that HW is ready for
next A-MPDU Tx state.
Changes in API to Rx A-MPDU were also made, reflected in iwlwifi changes as
well.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (based on Ron Rindjunsky's) creates a framework for
a unified way to pass BSS configuration to drivers that require
the information, e.g. for implementing power save mode.
This patch introduces new ieee80211_bss_conf structure that is
passed to the driver via the new bss_info_changed() callback
when the BSS configuration changes.
This new BSS configuration infrastructure adds the following
new features:
* drivers are notified of their association AID
* drivers are notified of association status
and replaces the erp_ie_changed() callback. The patch also does
the relevant driver updates for the latter change.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that support mixed AP/STA operation may well need to
know the type of a virtual interface when iterating over them.
The easiest way to support that is to move the interface type
variable into the vif structure.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices have a seperate LED which indicates if the radio is
enabled or not. This adds a LED trigger to mac80211 where drivers
can hook into when they are interested in radio status changes.
v2: Check hw.conf.radio_enabled when calling start().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the API to perform A-MPDU actions between mac80211 and low
level driver.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements cfg80211's get_key() to allow retrieving the sequence
counter for a TKIP or CCMP key from userspace. It also cleans up and
documents the associated low-level driver interface.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are various decisions influencing the decision whether to buffer
a frame for after the next DTIM beacon. The "do we have stations in PS
mode" condition cannot be tested by the driver so mac80211 has to do
that. To ease driver writing for hardware that can buffer frames until
after the next DTIM beacon, introduce a new txctl flag telling the
driver to buffer a specific frame.
While at it, restructure and comment the code for multicast buffering
and remove spurious "inline" directives.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch left only one user of the ieee80211_is_eapol()
function and that user can be eliminated easily by introducing
a new "frame is EAPOL" flag to handle the frame specially (we
already have this information) instead of doing the (expensive)
ieee80211_is_eapol() all the time.
Also, allow unencrypted frames to be sent when they are injected.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes mac80211 include the low-level MAC timestamp
in the radiotap header if the driver indicated (by a new
RX flag) that the timestamp is valid.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures the 802.11n mode of operation
internally in ieee80211_conf structure and in the low-level
driver as well (through op conf_ht).
It does not include AP configuration flows.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New structures:
- ieee80211_ht_info: describing STA's HT capabilities
- ieee80211_ht_bss_info: describing BSS's HT characteristics
Changed structures:
- ieee80211_hw_mode: now also holds PHY HT capabilities for each HW mode
- ieee80211_conf: ht_conf holds current self HT configuration
ht_bss_conf holds current BSS HT configuration
- flag IEEE80211_CONF_SUPPORT_HT_MODE added to indicate if HT use is
desired
- sta_info: now also holds Peer's HT capabilities
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interface iteration in mac80211 can be done without holding any
locks because I converted it to RCU. Initially, I thought this
wouldn't be needed for ieee80211_iterate_active_interfaces but
it's turning out that multi-BSS AP support can be much simpler
in a driver if ieee80211_iterate_active_interfaces can be called
without holding locks. This converts it to use RCU, it adds a
requirement that the callback it invokes cannot sleep.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes drivers need to know which interfaces are associated with
their hardware. Rather than forcing those drivers to keep track of
the interfaces that were added, this adds an iteration function to
mac80211.
As it is intended to be used from the interface add/remove callbacks,
the iteration function may currently only be called under RTNL.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver operations set_ieee8021x(), set_port_auth() and
set_privacy_invoked() are not used by any drivers, except
set_privacy_invoked() they aren't even used by mac80211.
Remove them at least until we need to support drivers with
mac80211 that require getting this information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows a driver to ask for a specific rate control algorithm.
The rate control algorithm asked for must be registered and be
available as a module or built-in.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds sta_notify callback and removes sta_table_notification
which was not used by any driver.
sta_notify() is essential for drivers that keeps notion of station
internally and need to be notified about removal or addition of a station
to the (I)BSS or assocation to an AP.
This version adds interface id to the parameter list
as suggested by Johannes Berg
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many devices have LEDs to indicate the link status.
Export this functionality to drivers.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This "algorithm" is used only internally and is not useful.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes the management interface since it is only required
for hostapd/userspace MLME, will not be in the final tree
at least in this form and hostapd/userspace MLME currently
do not work against this tree anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since I cannot convince the lazy driver authors (hello Michael)
to stop (ab)using the MGMT interface type internally in their
drivers, this patch introduces a new _INVALID type especially
for their use and changes all affected drivers to use it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not useful since we do not support probe response
offload to hardware at this time and beacons are set in
another way.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The typedef is not required, we can just use "enum ieee80211_key_alg"
instead of "ieee80211_key_alg"
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These inlines are generally useful, not just with mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a lot more documentation (in kernel-doc format)
to include/net/mac80211.h
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, hardware flags that drivers must set are not
documented well enough. Fix this.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211 to verify that VLAN interfaces
are valid and not bother drivers about them any more.
VLAN interfaces are now only valid when an AP interface
is up with the same MAC address, and are automatically
turned off when the AP interface is set down.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.
This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.
Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.
At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().
The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.
Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more mac80211 documentation.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE80211_CONF_SSID_HIDDEN setting is not useful for any driver
we have and should be a per-interface setting anyway. Remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows drivers to indicate bad FCS/PLCP CRC to the stack and
have the stack drop packets like that except for monitor interfaces.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TKIP mixing code was added for the benefit of Intel's ipw3945
chipset but that code ended up not using it. We have previously
identified many problems with this code and it crystallized that
library functions for mixing are likely to handle this in much
more generality and might allow b43 to take advantage of hardware
acceleration for TKIP.
Due to these reasons, remove the TKIP mixing for hardware
accelerated crypto operations.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the mac80211/driver interface rely only on the
IEEE80211_TXCTL_DO_NOT_ENCRYPT flag to signal to the driver whether
a frame should be encrypted or not, since mac80211 internally no
longer relies on HW_KEY_IDX_INVALID either this removes it, changes
the key index to be a u8 in all places and makes the full range of
the value available to drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch formats some documentation in mac80211.h into kerneldoc
and also adds some more explanations for hardware crypto.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No existing drivers use this callback, hence there's no telling
how it might be used. In fact, it is unlikely to be of much use
as-is because the default key index isn't something that the
driver can do much with without knowing which interface it was
for etc. And if it needs the key index for the transmitted frame,
it can get it by keeping a reference to the key_conf structure
and looking it up by hw_key_idx.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the various hardware crypto related
flags to make them more local, i.e. put them with each
key or each packet instead of into the hw struct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all mention of the atheros turbo modes that
can't possibly work properly anyway since in some places we don't
check for them when we should.
I have no idea what the iwlwifi drivers were doing with these but
it can't possibly have been correct.
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves all the key handling code out from ieee80211_ioctl.c
into key.c and also does the following changes including documentation
updates in mac80211.h:
1) Turn off hardware acceleration for keys when the interface
is down. This is necessary because otherwise monitor
interfaces could be decrypting frames for other interfaces
that are down at the moment. Also, it should go some way
towards better suspend/resume support, in any case the
routines used here could be used for that as well.
Additionally, this makes the driver interface nicer, keys
for a specific local MAC address are only ever present
while an interface with that MAC address is enabled.
2) Change driver set_key() callback interface to allow only
return values of -ENOSPC, -EOPNOTSUPP and 0, warn on all
other return values. This allows debugging the stack when
a driver notices it's handed a key while it is down.
3) Invert the flag meaning to KEY_FLAG_UPLOADED_TO_HARDWARE.
4) Remove REMOVE_ALL_KEYS command as it isn't used nor do we
want to use it, we'll use DISABLE_KEY for each key. It is
hard to use REMOVE_ALL_KEYS because we can handle multiple
virtual interfaces with different key configuration, so we'd
have to keep track of a lot of state for this and that isn't
worth it.
5) Warn when disabling a key fails, it musn't.
6) Remove IEEE80211_HW_NO_TKIP_WMM_HWACCEL in favour of per-key
IEEE80211_KEY_FLAG_WMM_STA to let driver sort it out itself.
7) Tell driver that a (non-WEP) key is used only for transmission
by using an all-zeroes station MAC address when configuring.
8) Change the set_key() callback to have access to the local MAC
address the key is being added for.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the default_wep_only stuff, this wasn't really done well
and no current driver actually cares.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch embeds the struct ieee80211_key_conf into struct ieee80211_key
and thus avoids allocations and having data present twice.
This required some more changes:
1) The removal of the IEEE80211_KEY_DEFAULT_TX_KEY key flag.
This flag isn't used by drivers nor should it be since
we have a set_key_idx() callback. Maybe that callback needs
to be extended to include the key conf, but only a driver that
requires it will tell.
2) The removal of the IEEE80211_KEY_DEFAULT_WEP_ONLY key flag.
This flag is global, so it shouldn't be passed in the key
conf structure. Pass it to the function instead.
Also, this patch removes the AID parameter to the set_key() callback
because it is currently unused and the hardware currently cannot know
about the AID anyway. I suspect this was used with some hardware that
actually selected the AID itself, but that functionality was removed.
Additionally, I've removed the ALG_NULL key algorithm since we have
ALG_NONE.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ioctls
* PRISM2_PARAM_RADAR_DETECT
* PRISM2_PARAM_SPECTRUM_MGMT
are not used by hostapd or wpa_supplicant,
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ioctls
* PRISM2_PARAM_STA_ANTENNA_SEL
* PRISM2_PARAM_TX_POWER_REDUCTION
* PRISM2_PARAM_DEFAULT_WEP_ONLY
are not used by hostapd or wpa_supplicant.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ioctls
* PRISM2_PARAM_ANTENNA_MODE
* PRISM2_PARAM_STAT_TIME
are not used by hostapd or wpa_supplicant.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing key selection for software decryption, mac80211 gets
a few things wrong: it always uses pairwise keys if configured,
even if the frame is addressed to a multicast address. Also, it
doesn't allow using a key index of zero if a pairwise key has
also been found.
This patch changes the key selection code to be (more) in line
with the 802.11 specification. I have confirmed that with this,
multicast frames are correctly decrypted and I've tested with
WEP as well.
While at it, I've cleaned up the semantics of the hardware flags
IEEE80211_HW_WEP_INCLUDE_IV and IEEE80211_HW_DEVICE_HIDES_WEP
and clarified them in the mac80211.h header; it is also now
allowed to set the IEEE80211_HW_DEVICE_HIDES_WEP option even if
it only applies to frames that have been decrypted by the hw,
unencrypted frames must be dropped but encrypted frames that
the hardware couldn't handle can be passed up unmodified.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unused in drivers, userspace and mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag is never checked because drivers can simply call
ieee80211_beacon_get() regardless of setting this flag.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback isn't used so remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
zd1211rw and bcm43xx are interested in being notified when ERP IE conditions
change, so that they can reprogram a register which affects how control frames
are transmitted.
This patch adds an interface similar to the one that can be found in softmac.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similarly to CTS protection, whether short preambles are used for 802.11b
transmissions should be a per-subif setting, not device global.
For STAs, this patch makes short preamble handling automatic based on the ERP
IE. For APs, hostapd still uses the prism ioctls, but the write ioctl has been
restricted to AP-only subifs.
ieee80211_txrx_data.short_preamble (an unused field) was removed.
Unfortunately, some API changes were required for the following functions:
- ieee80211_generic_frame_duration
- ieee80211_rts_duration
- ieee80211_ctstoself_duration
- ieee80211_rts_get
- ieee80211_ctstoself_get
Affected drivers were updated accordingly.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 informs the driver what the short and long retry values are through
set_retry_limit(), but when packets are being transmitted it did not inform the
driver which of the 2 retry limits should actually be used.
Instead it sends the actual value, but for drivers that can only set the retry limit
and the register and in the descriptor need to indicate which of the limits should
be used this is not really useful.
This patch will add a IEEE80211_TXCTL_LONG_RETRY_LIMIT flag to the
ieee80211_tx_control structure. By default the short retry limit should be
used but if the flag is set the long retry should be used.
This does not prevent the driver to ignore the request for "no retry" packets,
but at least those will be send out with the short retry limit. But there is no
perfect cure for this problem.. :(
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta_info code has some awkward locking which prevents some driver
callbacks from being allowed to sleep. This patch makes the locking more
focused so code that calls driver callbacks are allowed to sleep. It also
converts sta_lock to a rwlock.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The semantics of not having an add_interface callback are not well
defined, this callback is required because otherwise you cannot obtain
the requested MAC address of the device. Change the documentation to
reflect this, add a note about having no MAC address at all, add a
warning that mac_addr in struct ieee80211_if_init_conf can be NULL and
finally verify that a few callbacks are assigned by way of BUG_ON()
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ieee80211_set_aid_for_sta and associated code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo