The uart works in the DCE mode by default, but sometime we need it
works at the DTE mode.
This patch adds the support for the DTE mode.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables the overrun error (ORE) interrupt and increases the
counter in case of overrun.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 677fe55 (serial: imx: Fix recursive locking bug) introduces an
uninitialized variable warning as below.
CC drivers/tty/serial/imx.o
drivers/tty/serial/imx.c: In function ‘imx_console_write’:
include/linux/spinlock.h:340:2: warning: ‘flags’ may be used uninitialized in this function [-Wuninitialized]
drivers/tty/serial/imx.c:1214:16: note: ‘flags’ was declared here
Initialize the variable to suppress the warning.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ec1882df2 (tty: serial: imx: console write routing is unsafe
on SMP) introduced a recursive locking bug in imx_console_write().
The callchain is:
imx_rxint()
spin_lock_irqsave(&sport->port.lock,flags);
...
uart_handle_sysrq_char();
sysrq_function();
printk();
imx_console_write();
spin_lock_irqsave(&sport->port.lock,flags); <--- DEAD
The bad news is that the kernel debugging facilities can dectect the
problem, but the printks never surface on the serial console for
obvious reasons.
There is a similar issue with oops_in_progress. If the kernel crashes
we really don't want to be stuck on the lock and unable to tell what
happened.
In general most UP originated drivers miss these checks and nobody
ever notices because CONFIG_PROVE_LOCKING seems to be still ignored by
a large number of developers.
The solution is to avoid locking in the sysrq case and trylock in the
oops_in_progress case.
This scheme is used in other drivers as well and it would be nice if
we could move this to a common place, so the usual copy/paste/modify
bugs can be avoided.
Now there is another issue with this scheme:
CPU0 CPU1
printk()
rxint()
sysrq_detection() -> sets port->sysrq
return from interrupt
console_write()
if (port->sysrq)
avoid locking
port->sysrq is reset with the next receive character. So as long as
the port->sysrq is not reset and this can take an endless amount of
time if after the break no futher receive character follows, all
console writes happen unlocked.
While the current writer is protected against other console writers by
the console sem, it's unprotected against open/close or other
operations which fiddle with the port. That's what the above mentioned
commit tried to solve.
That's an issue in all drivers which use that scheme and unfortunately
there is no easy workaround. The only solution is to have a separate
indicator port->sysrq_cpu. uart_handle_sysrq_char() then sets it to
smp_processor_id() before calling into handle_sysrq() and resets it to
-1 after that. Then change the locking check to:
if (port->sysrq_cpu == smp_processor_id())
locked = 0;
else if (oops_in_progress)
locked = spin_trylock_irqsave(port->lock, flags);
else
spin_lock_irqsave(port->lock, flags);
That would force all other cpus into the spin_lock path. Problem
solved, but that's way beyond the scope of this fix and really wants
to be implemented in a common function which calls the uart specific
write function to avoid another gazillion of hard to debug
copy/paste/modify bugs.
Reported-and-tested-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable <stable@vger.kernel.org> # 3.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cdc8da3998.
In my attempt to fix a build warning on arm randconfig a build error on
imx_v6_v7_defconfig was introduced, so revert it for now.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_CONSOLE_POLL is not defined, the following build warning happens:
drivers/tty/serial/imx.c:274:13: warning: 'imx_port_ucrs_save' defined but not used [-Wunused-function]
drivers/tty/serial/imx.c:283:13: warning: 'imx_port_ucrs_restore' defined but not used [-Wunused-function]
Move imx_port_ucrs_saver/restore under CONFIG_CONSOLE_POLL ifdef block to fix it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Silences the following checkpatch error:
ERROR: that open brace { should be on the previous line
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
platform_get_drvdata always retrun a valid value after probe succeed.
It also fixed smatch warnings:
drivers/tty/serial/imx.c:1376 serial_imx_suspend() warn: variable dereferenced before check 'sport' (see line 1372)
drivers/tty/serial/imx.c:1392 serial_imx_resume() warn: variable dereferenced before check 'sport' (see line 1388)
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
These error paths are used more often now after deep changes to the
clock code and pinctrl is still new for imx. So help debugging and give
clues in the boot log.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the clock configuration from imx_setup_ufcr(). This
isn't needed here and will cause garbage output if done.
To be be sure that we only touch the bits we want (TXTL and RXTL)
we have to mask out all other bits of the UFCR register. Add
one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6).
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Xinyu Chen <xinyu.chen@freescale.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console feature's write routing is unsafe on SMP with
the startup/shutdown call.
There could be several consumers of the console
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which open /dev/console and write with sys_write()
The shell goes into the normal uart open/write routing,
but the other two go into the console operations.
The open routing calls imx serial startup, which will write USR1/2
register without any lock and critical with imx_console_write call.
Add a spin_lock for startup/shutdown/console_write routing.
This patch is a port from Freescale's Android kernel.
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This handles the merge issue in:
arch/um/drivers/line.c
arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the part of the effort to enable SPARE_IRQ for imx platform,
the macro MXC_INTERNAL_IRQS will be removed. The imx serial driver
has a references to it for a decision on flags of request_irq call
based on rtsirq is beyond MXC_INTERNAL_IRQS. However the searching
on imx platform code tells that rtsirq will never be beyond
MXC_INTERNAL_IRQS. That said, the check, consequently the reference
to MXC_INTERNAL_IRQS are not needed, so remove them.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
This is only cosmetic for now. In case that
http://mid.gmane.org/1335171381-24869-1-git-send-email-u.kleine-koenig@pengutronix.de
will be applied, it fixes a warning
drivers/tty/serial/imx.c: In function 'serial_imx_probe_dt':
drivers/tty/serial/imx.c:1430:17: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
though.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
del_timer_sync() acquires its own lock and doesn't have to be nested
within the spinlock of sport->port.lock in imx_set_termios(), which
will cause potential deadlock. Fix this by moving it outside.
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These methods are invoked if the iMX uart is used in conjuction with kgdb during
early boot. In order to access the UART without the interrupts, the kernel uses
the basic polling methods for IO with the device. With these methods
implemented, it is now possible to enable kgdb during early boot over serial.
Signed-off-by: Saleem Abdulrasool <compnerd@compnerd.org>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
CC: linux-serial@vger.kernel.org
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Factor out the uart save/restore functionality instead of
having the same code several times in the driver.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
CC: Saleem Abdulrasool <compnerd@compnerd.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
CC: linux-serial@vger.kernel.org
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the uart device is instantiated by dt but dt doesn't provide an
alias then better let probing fail instead of falling back to an
unrelated device id used for the line number and no platform data.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A quick look at of_alias_get_id shows that in the error case it returns
-ENODEV, too, but still it's better style to propagate the value as is.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Jason Liu <jason.hui@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow UART to be a source for wakeup from low power mode.
Tested on a MX27PDK by doing:
echo enabled > /sys/devices/platform/imx21-uart.0/tty/ttymxc0/power/wakeup
echo mem > /sys/power/state
and then pressing a key in the console will wakeup the sytem.
Suggested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As of_alias_get_id() gets fixed and ready for use, the patch adds the
of_alias_get_id() reference back to imx serial driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[grant.likely: changed pr_err() to dev_err(), dropped unnecessary else]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The imx UART hardware controller can identify BREAK character and the
imx_set_termios() can accept BRKINT set by users, but current existing
imx_rxint() can't pass BREAK character and TTY_BREAK to the tty layer
as other serial drivers do (8250.c omap_serial.c).
Here add code to handle BREAK character and pass it to tty layer.
To detect error occurrence, i use URXD_ERR to replace (URXD_OVRRUN |
URXD_FRMERR | ...) because any kind of error occurs, URXD_ERR will
always be set to 1.
I put the URXD_BRK to the first place to check since when BREAK error
occurs, not only URXD_BRK is set to 1, but also URXD_PRERR and
URXD_FRMERR are all set to 1. This arrangement can filter out fake
parity and frame errors when BREAK error occurs.
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
of_alias_get_id() is broken and being reverted. Remove the reference
to it and replace with a single incrementing id number.
There is no risk of regression here on the imx driver since the imx
change to use of_alias_get_id() is commit 22698aa2, "serial/imx: add
device tree probe support" which is new for v3.1, and it won't get
used unless CONFIG_OF is enabled and the board is booted using a
device tree. A single incrementing integer is sufficient for now.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
It adds device tree probe support for imx tty/serial driver.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The patch removes all the uses of cpu_is_mx1(). Instead, it uses
the .id_table of platform_driver to distinguish the uart device type,
IMX1_UART and IMX21_UART. The IMX21_UART type runs on all i.mx
except i.mx1.
A couple of !cpu_is_mx1 logic gets turned into is_imx21_uart,
as the codes wrapped there are really IMX21 type uart specific.
It also removes macro MX1_UCR3_REF25 and MX1_UCR3_REF30 which are
not used anywhere.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (48 commits)
serial: 8250_pci: add support for Cronyx Omega PCI multiserial board.
tty/serial: Fix break handling for PORT_TEGRA
tty/serial: Add explicit PORT_TEGRA type
n_tracerouter and n_tracesink ldisc additions.
Intel PTI implementaiton of MIPI 1149.7.
Kernel documentation for the PTI feature.
export kernel call get_task_comm().
tty: Remove to support serial for S5P6442
pch_phub: Support new device ML7223
8250_pci: Add support for the Digi/IBM PCIe 2-port Adapter
ASoC: Update cx20442 for TTY API change
pch_uart: Support new device ML7223 IOH
parport: Use request_muxed_region for IT87 probe and lock
tty/serial: add support for Xilinx PS UART
n_gsm: Use print_hex_dump_bytes
drivers/tty/moxa.c: Put correct tty value
TTY: tty_io, annotate locking functions
TTY: serial_core, remove superfluous set_task_state
TTY: serial_core, remove invalid test
Char: moxa, fix locking in moxa_write
...
Fix up trivial conflicts in drivers/bluetooth/hci_ldisc.c and
drivers/tty/serial/Makefile.
I did the hci_ldisc thing as an evil merge, cleaning things up.
If cts changes between reading the level at the cts input (USR1_RTSS)
and acking the irq (USR1_RTSD) the last edge doesn't generate an irq and
uart_handle_cts_change is called with a outdated value for cts.
The race was introduced by commit
ceca629 ([ARM] 2971/1: i.MX uart handle rts irq)
Reported-by: Arwed Springer <Arwed.Springer@de.trumpf.com>
Tested-by: Arwed Springer <Arwed.Springer@de.trumpf.com>
Cc: stable@kernel.org # 2.6.14+
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remove invalid location line in each file header after location
moved from driver/char to driver/tty
Signed-off-by: Jovi Zhang <bookjovi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Huang Shijie