* Check for IDE_HFLAG_NO_SET_MODE host flag in ide_set_pio(),
ide_set_[pio,dma]_mode(), ide_set_xfer_rate() and set_pio_mode().
* Remove no longer needed IDE_HFLAG_NO_SET_MODE host flag checking
from ide_tune_dma().
* Remove superfluous ->set_pio_mode checking from do_special().
This is a part of preparations for adding 'struct ide_port_ops'.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out chipset family detection from init_chipset_sis5513()
to sis_find_family().
* Use sis_find_family() in sis5513_init_one() to fail early if the
chipset is unsupported.
* Keep a local copy sis5513_chipset in sis5513_init_one()
and set .udma_mask according to chipset family.
* Remove no longer need ->ultra_mask setting from init_hwif_sis5513().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Allocate 'struct it821x_dev' objects for both ports in it821x_init_one().
Fixes potential OOPS in it821x_quirkproc() (uses 'itdev' unconditionally)
and other problems ('itdev' is needed for correct operation of the driver).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set IDE_HFLAG_SINGLE host flag in qd_probe() for QD6500 and QD6580
with the second port disabled.
* Check for IDE_HFLAG_SINGLE in qd6580_port_init_devs() instead of
using cached value of QD6580 Control register.
* Don't cache QD6580 Control register value in hwif->config_data
(bits 8-15) and remove no longer needed QD_CONTROL() macro.
* Cache QD65xx base address in hwif->config_data (bits 8-15)
instead of hwif->select_data.
* Set hwif->config_data in qd_probe() and remove qd_setup() helper.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
qd_select() checks itself whether timings should be reprogrammed so
remove superfluous qd_timing_ok() and always use ->selectproc method
(rename qd_select() to qd65xx_select() while at it).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
File is now error free, only a few
WARNING: line over 80 characters
are left.
Compile tested.
[bart: md5sum checked]
Signed-off-by: Paolo Ciarrocchi <paolo.ciarrocchi@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
File is now error free.
Compile tested.
[bart: minor fixes, md5sum checked]
Signed-off-by: Paolo Ciarrocchi <paolo.ciarrocchi@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix a lot of errors and warnings.
Compile tested.
[bart: some fixes, md5sum checked]
Signed-off-by: Paolo Ciarrocchi <paolo.ciarrocchi@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix all the errors and a few warnings.
Compile tested.
[bart: some fixes, md5sum checked]
Signed-off-by: Paolo Ciarrocchi <paolo.ciarrocchi@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Lot of errors and warnings removed.
Compile tested.
[bart: minor fixes, md5sum checked]
Signed-off-by: Paolo Ciarrocchi <paolo.ciarrocchi@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
File is now error and warning free.
Compile tested.
[bart: md5sum checked]
Signed-off-by: Paolo Ciarrocchi <paolo.ciarrocchi@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
File is now error free.
Compile tested.
[bart: minor fixes, md5sum checked]
Signed-off-by: Paolo Ciarrocchi <paolo.ciarrocchi@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
About 300 errors and warnings fixed.
File is now error free.
Compile tested.
[bart: minor fixes, md5sum checked]
Signed-off-by: Paolo Ciarrocchi <paolo.ciarrocchi@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
File is now error and warning free.
Compile tested.
[bart: md5sum checked]
Signed-off-by: Paolo Ciarrocchi <paolo.ciarrocchi@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
File is now error free.
Compile tested.
[bart: minor fixes, md5sum checked]
Signed-off-by: Paolo Ciarrocchi <paolo.ciarrocchi@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All host drivers now either set hwif->mmio or reserve continuous
I/O resources so remove no longer needed hwif->straight8 flag
and never reached code for 'hwif->straight8 == 0' case.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei suggested that it shouldn't be necessary + it had no effect
anyway since ide_id_dma_bug() is called earlier in ide_tune_dma().
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Tell IDE layer to not manage resources by setting
hwif->mmio flag and request resources in falconide_init().
* Use request_mem_region() for resources reservation.
* Use driver name for resources reservation.
v2:
* Fix missing printk() parameter. (Noticed by Geert Uytterhoeven)
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Tell IDE layer to not manage resources by setting
hwif->mmio flag and request resources in m8xx_ide_init_ports().
* Use request_mem_region() for resources reservation.
* Use driver name for resources reservation.
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make m8xx_ide_init_ports() return an error value.
* Update mpc8xx_ide_probe() to setup/probe only ports for which
m8xx_ide_init_ports() succedded.
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Tell IDE layer to not manage resources by setting
hwif->mmio flag and request resources in bastide_init().
* Use request_mem_region() for resources reservation.
* Use driver name for resources reservation.
Cc: Ben Dooks <support@simtec.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tell IDE layer to not manage resources by setting hwif->mmio flag.
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tell IDE layer to not manage resources by always setting hwif->mmio flag
(resources are handled by a platform device).
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This removes the internal ide-cd buffer and falls back to read-ahead block layer
capabilities. Thorough testing (cd burning, dvd read, raw read) gives with the
bufferless mode marginally better performance in addition to simplified code.
bufferless:
dd: reading `/dev/hdc': Input/output error
6238+0 records in
6238+0 records out
204406784 bytes (204 MB) copied, 259.891 s, 787 kB/s
real 4m21.598s
user 0m0.014s
sys 0m0.744s
with the old buffer (2.6.25-rc1):
dd: reading `/dev/hdc': Input/output error
6238+0 records in
6238+0 records out
204406784 bytes (204 MB) copied, 262.893 s, 778 kB/s
real 4m22.938s
user 0m0.009s
sys 0m0.771s
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There are no changes to the resulting drivers/ide/ide-disk.o binary file
(md5sum-s after and before the patch match).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out common code from proc_idedisk_read_smart_{thresholds,values}()
to proc_idedisk_read_smart() helper.
* Rename proc_idedisk_read_smart_thresholds() to proc_idedisk_read_st()
and proc_idedisk_read_smart_values() to proc_idedisk_read_sv().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
v2:
* Fix comment (noticed by Sergei Shtylyov).
v3:
* Fix no initalization of idx in some case. (Johann Felix Soden)
Cc: Johann Felix Soden <johfel@users.sourceforge.net>
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_QD_2ND_PORT host flag to indicate the need of skipping
first ide_hwifs[] slot for the second port of QD65xx controller.
* Handle this new host flag in ide_find_port_slot().
* Convert legacy VLB host drivers to use ide_find_port().
While at it:
* Fix couple of printk()-s in qd65xx host driver to not use hwif->name.
v2:
* Fix qd65xx.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Change ide_match_hwif() argument from 'u8 bootable' to
'struct ide_port_info *d'.
* Move ide_match_hwif() to ide-probe.c from setup-pci.c and rename
it to ide_find_port_slot(). Update some comments while at it.
* ide_find_port() can be now just a wrapper for ide_find_port_slot().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
No need for it nowadays so remove quirk code from ide_get_best_pio_mode()
and IDE_HFLAG_PIO_DOWNGRADE host flag.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
"bootable" should be the default behavior so replace
IDE_HFLAG_BOOTABLE host flag with IDE_HFLAG_NON_BOOTABLE.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Return error value in qd_probe() and use it in qd65xx_init()
instead of checking ide_hwifs[].chipset.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace 'unsigned char hwif_id' by 'ide_hwif_t *hwif' in struct scc_ports.
This allows us to remove ide_hwifs[] usage from scc_remove().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer needed matching against I/O base and 'io_base' argument.
* Move printk() to the caller and remove 'name' argument.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This function didn't actually check if a given BAR is in I/O space because of
using the bogus PCI_BASE_ADDRESS_IO_MASK (which equals ~3) to test the resource
flags instead of IORESOURCE_IO -- fix this, make ide_hwif_configure() check the
results failing if necessary, and move the printk() call to the failure path.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The 4drives should be a tristate, the following breakage occurs otherwise:
ERROR: "probe_4drives" [drivers/ide/ide-core.ko] undefined!
The following (compile tested) patch fixes it for me.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Using i2c_transfer instead of i2c_master_recv in ir_probe saves a
temporary memory allocation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following cleanups and fixes:
- "debug" is definitely not a good name for a global variable,
renamed it to "au0828_debug"
this fixes a compile error with some kernel configurations
- since the module parameter is int the variable shouldn't be unsigned
- remove the {usb,bridge,i2c}_debug module parameters since they are
already covered by the "debug" module parameter
- remove the unused au0828_bcount
- make the needlessly global i2c_scan static
- make the needlessly global dvb_register() static
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
set_addr log were almost useless: discarded SET_TYPE_ADDR commands weren't
reported.
This patch changed set_addr printk to print a message only if set_addr is
wrong.
It also fix printk at set_type, since, if an attach were failing, nothing
were reported.
With the current code, working or not, a call to set_addr will produce a debug
printk.
also, set_type() were producing a false error message on tuner_xc2028, since
it were requesting for setting a frequency on a place where firmware name
weren't set yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Single-bit signed bitfields can only take 0/-1 rather than 0/1 as the
drivers seems to assume...add unsigned.
Noticed by sparse:
drivers/media/video/pvrusb2/pvrusb2-devattr.h:107:34: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:114:37: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:117:30: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:120:23: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:124:24: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:128:23: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:138:36: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:143:24: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:144:28: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:145:26: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:146:23: error: dubious one-bit signed bitfield
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds full support for this demodulator.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make it unsigned (0/1) rather than signed (0/-1).
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes a copy and paste error in check of kzalloc return value. The check block
was copied from the previous allocation but the variable wasn't exchanged.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
some gcc versions complain that fh is used without being defined.
The error report is bogus. However, fixing it is trivial. Better to make
gcc happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As of now, agp_compat_ioctl already runs without the BKL. Mutual exclusion
is enforced by agp_fe.agp_mutex in agp_ioctl() and agp_compat_ioctl().
Apply the same locking rationale to the two functions allowing BKL cleanup.
Signed-off-by: Mathieu Segaud <mathieu.segaud@regala.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Introduced between 2.6.25-rc2 and -rc3
drivers/char/agp/amd-k7-agp.c:439:6: warning: symbol 'cap_ptr' shadows an
earlier one
drivers/char/agp/amd-k7-agp.c:414:5: originally declared here
cap_ptr is never used again in this function, don't bother redeclaring.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Other Authors: Michel Dänzer <michel@tungstengraphics.com>
mga: Ian Romanick <idr@us.ibm.com>
via: Thomas Hellstrom <thomas-at-tungstengraphics-dot-com>
This re-works the DRM internals to provide a better interface for drivers
to expose vblank on multiple crtcs.
It also includes work done by Michel on making i915 triple buffering and pageflipping work properly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The batchbuffer submission paths were fixed to use the 965-specific command,
but the vblank tasklet was not. When the older version is sent, the 965 will
lock up.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that the ATI pcigart code uses dma_alloc_coherent, we don't need
the dma_sync_single_for_device() that we used to have here.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The patch for supporting non coherent PCI DMA in the DRM was mismerged
causing the page protection to be updated for the wrong type of
mapping.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (49 commits)
[POWERPC] Add zImage.iseries to arch/powerpc/boot/.gitignore
[POWERPC] bootwrapper: fix build error on virtex405-head.S
[POWERPC] 4xx: Fix 460GT support to not enable FPU
[POWERPC] 4xx: Add NOR FLASH entries to Canyonlands and Glacier dts
[POWERPC] Xilinx: of_serial support for Xilinx uart 16550.
[POWERPC] Xilinx: boot support for Xilinx uart 16550.
[POWERPC] celleb: Add support for PCI Express
[POWERPC] celleb: Move miscellaneous files for Beat
[POWERPC] celleb: Move a file for SPU on Beat
[POWERPC] celleb: Move files for Beat mmu and iommu
[POWERPC] celleb: Move files for Beat hvcall interfaces
[POWERPC] celleb: Move the SCC related code for celleb
[POWERPC] celleb: Move the files for celleb base support
[POWERPC] celleb: Consolidate io-workarounds code
[POWERPC] cell: Generalize io-workarounds code
[POWERPC] Add CONFIG_PPC_PSERIES_DEBUG to enable debugging for platforms/pseries
[POWERPC] Convert from DBG() to pr_debug() in platforms/pseries/
[POWERPC] Register udbg console early on pseries LPAR
[POWERPC] Mark udbg console as CON_ANYTIME, ie. callable early in boot
[POWERPC] Set udbg_console index to 0
...
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Add default-on trigger
leds: Document the context brightness_set needs
leds: Add new driver for the LEDs on the Freecom FSG-3
leds: Add support to leds with readable status
leds: enable support for blink_set() platform hook in leds-gpio
leds: Cleanup various whitespace and code style issues
leds: disable triggers on brightness set
leds: Add mail LED support for "Clevo D400P"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-pat:
generic: add ioremap_wc() interface wrapper
/dev/mem: make promisc the default
pat: cleanups
x86: PAT use reserve free memtype in mmap of /dev/mem
x86: PAT phys_mem_access_prot_allowed for dev/mem mmap
x86: PAT avoid aliasing in /dev/mem read/write
devmem: add range_is_allowed() check to mmap of /dev/mem
x86: introduce /dev/mem restrictions with a config option
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_bf54x: decrease count first.
sata_mv: re-enable hotplug, update TODO list
sata_mv: leave SError bits untouched in mv_err_intr
sata_mv: more interrupt handling rework
sata_mv: tidy host controller interrupt handling
sata_mv: simplify request/response queue handling
sata_mv: simplify freeze/thaw bit-shift calculations
sata_mv mask all interrupt coalescing bits
sata_mv more cosmetics
ata_piix: add Asus Eee 701 controller to short cable list
libata-eh set tf flags in NCQ EH result_tf
make sata_set_spd_needed() static
make sata_print_link_status() static
libata-acpi.c: remove unneeded #if's
sata_nv: make hardreset return -EAGAIN on success
ahci: retry enabling AHCI a few times before spitting out WARN_ON()
libata: make WARN_ON conditions in ata_sff_hsm_move() more strict
ATA/IDE: fix platform driver hotplug/coldplug
sata_sis: SCR accessors return -EINVAL when requested SCR isn't available
libata: functions with definition should not be extern
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (120 commits)
usb: don't update devnum for wusb devices
wusb: make ep0_reinit available for modules
wusb: devices dont use a set address
wusb: teach choose_address() about wireless devices
wusb: add link wusb-usb device
wusb: add authenticathed bit to usb_dev
USB: remove unnecessary type casting of urb->context
usb serial: more fixes and groundwork for tty changes
USB: replace remaining __FUNCTION__ occurrences
USB: usbfs: export the URB_NO_INTERRUPT flag to userspace
USB: fix compile problems in ehci-hcd
USB: ehci: qh_completions cleanup and bugfix
USB: cdc-acm: signedness fix
USB: add documentation about callbacks
USB: don't explicitly reenable root-hub status interrupts
USB: OHCI: turn off RD when remote wakeup is disabled
USB: HCDs use the do_remote_wakeup flag
USB: g_file_storage: ignore bulk-out data after invalid CBW
USB: serial: remove endpoints setting checks from core and header
USB: serial: remove unneeded number endpoints settings
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-xen-next: (52 commits)
xen: add balloon driver
xen: allow compilation with non-flat memory
xen: fold xen_sysexit into xen_iret
xen: allow set_pte_at on init_mm to be lockless
xen: disable preemption during tlb flush
xen pvfb: Para-virtual framebuffer, keyboard and pointer driver
xen: Add compatibility aliases for frontend drivers
xen: Module autoprobing support for frontend drivers
xen blkfront: Delay wait for block devices until after the disk is added
xen/blkfront: use bdget_disk
xen: Make xen-blkfront write its protocol ABI to xenstore
xen: import arch generic part of xencomm
xen: make grant table arch portable
xen: replace callers of alloc_vm_area()/free_vm_area() with xen_ prefixed one
xen: make include/xen/page.h portable moving those definitions under asm dir
xen: add resend_irq_on_evtchn() definition into events.c
Xen: make events.c portable for ia64/xen support
xen: move events.c to drivers/xen for IA64/Xen support
xen: move features.c from arch/x86/xen/features.c to drivers/xen
xen: add missing definitions in include/xen/interface/vcpu.h which ia64/xen needs
...
* git://git.infradead.org/mtd-2.6: (82 commits)
[MTD] m25p80: Add Support for ATMEL AT25DF641 64-Megabit SPI Flash
[MTD] m25p80: add FAST_READ access support to M25Pxx
[MTD] [NAND] bf5xx_nand: Avoid crash if bfin_mac is installed.
[MTD] [NAND] at91_nand: control NCE signal
[MTD] [NAND] AT91 hardware ECC compile fix for at91sam9263 / at91sam9260
[MTD] [NAND] Hardware ECC controller on at91sam9263 / at91sam9260
[JFFS2] Introduce dbg_readinode2 log level, use it to shut read_dnode() up
[JFFS2] Fix jffs2_reserve_space() when all blocks are pending erasure.
[JFFS2] Add erase_checking_list to hold blocks being marked.
UBI: add a message
[JFFS2] Return values of jffs2_block_check_erase error paths
[MTD] Clean up AR7 partition map support
[MTD] [NOR] Fix Intel CFI driver for collie flash
[JFFS2] Finally remove redundant ref->__totlen field.
[JFFS2] Honour TEST_TOTLEN macro in debugging code. ref->__totlen is going!
[JFFS2] Add paranoia debugging for superblock counts
[JFFS2] Fix free space leak with in-band cleanmarkers
[JFFS2] Self-sufficient #includes in jffs2_fs_i.h: include <linux/mutex.h>
[MTD] [NAND] Verify probe by retrying to checking the results match
[MTD] [NAND] S3C2410 Allow ECC disable to be specified by the board
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: silence defined but not used warning in non-modular builds
ieee1394: rawiso: requeue packet for transmission after skipped cycle
Currently the kernel will issue the following warning:
drivers/ieee1394/raw1394.c:2938: warning: 'raw1394_id_table' defined but not used
Add #ifdef MODULE guards around the declaration.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Ditto with dv1394_id_table and video1394_id_table.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
As it seems, some host controllers have issues that can cause them to
skip cycles now and then when using large packets. I suspect that this
is due to DMA not succeeding in time. If the transmit fifo can't contain
more than one packet (big packets), the DMA should provide a new packet
each cycle (125us). I am under the impression that my current PCI
express test system can't guarantee this.
In any case, the patch tries to provide a workaround as follows:
The DMA program descriptors are modified such that when an error occurs,
the DMA engine retries the descriptor the next cycle instead of
stalling. This way no data is lost. The side effect of this is that
packets are sent with one cycle delay. This however might not be that
much of a problem for certain protocols (e.g. AM824). If they use
padding packets for e.g. rate matching they can drop one of those to
resync the streams.
The amount of skips between two userspace wakeups is counted. This
number is then propagated to userspace through the upper 16 bits of the
'dropped' parameter. This allows unmodified userspace applications due
to the following:
1) libraw simply passes this dropped parameter to the user application
2) the meaning of the dropped parameter is: if it's nonzero, something
bad has happened. The actual value of the parameter at this moment does
not have a specific meaning.
A libraw client can then retrieve the number of skipped cycles and
account for them if needed.
Signed-off-by: Pieter Palmers <pieterp@joow.be>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The small patch below:
- Removes the unused md argument from both specific_minor() and next_free_minor()
- Folds kmalloc + memset(0) into a single kzalloc call in alloc_dev()
This has been compile tested on x86.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm_create_error_table() was added in kernel 2.6.18 and never used...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
void returning functions returned the return value of another void
returning function...
Spotted by sparse.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove an avoidable 3ms delay on some dm-raid1 and kcopyd I/O.
It is specified that any submitted bio without BIO_RW_SYNC flag may plug the
queue (i.e. block the requests from being dispatched to the physical device).
The queue is unplugged when the caller calls blk_unplug() function. Usually, the
sequence is that someone calls submit_bh to submit IO on a buffer. The IO plugs
the queue and waits (to be possibly joined with other adjacent bios). Then, when
the caller calls wait_on_buffer(), it unplugs the queue and submits the IOs to
the disk.
This was happenning:
When doing O_SYNC writes, function fsync_buffers_list() submits a list of
bios to dm_raid1, the bios are added to dm_raid1 write queue and kmirrord is
woken up.
fsync_buffers_list() calls wait_on_buffer(). That unplugs the queue, but
there are no bios on the device queue as they are still in the dm_raid1 queue.
wait_on_buffer() starts waiting until the IO is finished.
kmirrord is scheduled, kmirrord takes bios and submits them to the devices.
The submitted bio plugs the harddisk queue but there is no one to unplug it.
(The process that called wait_on_buffer() is already sleeping.)
So there is a 3ms timeout, after which the queues on the harddisks are
unplugged and requests are processed.
This 3ms timeout meant that in certain workloads (e.g. O_SYNC, 8kb writes),
dm-raid1 is 10 times slower than md raid1.
Every time we submit something asynchronously via dm_io, we must unplug the
queue actually to send the request to the device.
This patch adds an unplug call to kmirrord - while processing requests, it keeps
the queue plugged (so that adjacent bios can be merged); when it finishes
processing all the bios, it unplugs the queue to submit the bios.
It also fixes kcopyd which has the same potential problem. All kcopyd requests
are submitted with BIO_RW_SYNC.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Bartlomiej Zolnierkiewicz