For correctness, the initial page table located right before the
decompressed kernel should be considered when determining if relocation
is required.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
If the zImage load address is slightly below the relocation address,
there is a risk for the copied data to overwrite the copy loop or
cache flush code that the relocation process requires. Always
bump the relocation address by the size of that code to avoid this
issue.
Noticed by Tony Lindgren <tony@atomide.com>.
While at it, let's start the copy from the restart symbol which makes
the above code size computation possible by the assembler directly
(same sections), given that we don't need to preserve the code before
that point anyway. And therefore we don't need to carry the _start
pointer in r5 anymore.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Otherwise cache_clean_flush can overwrite some of the relocated
area depending on where the kernel image gets loaded. This fixes
booting on n900 after commit 6d7d0ae515
(ARM: 6750/1: improvements to compressed/head.S).
Thanks to Aaro Koskinen <aaro.koskinen@nokia.com> for debugging
the address of the relocated area that gets corrupted, and to
Nicolas Pitre <nicolas.pitre@linaro.org> for the other uncompress
related fixes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
With ARMv5+ and EABI, the compiler expects a 64-bit aligned stack so
instructions like STRD and LDRD can be used. Without this, mysterious
boot failures were seen semi randomly with the LZMA decompressor.
While at it, let's align .bss as well.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
CC: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
Reorder
irq_set_chip()
irq_set_chip_data()
irq_set_handler()
to
irq_set_chip()
irq_set_handler()
irq_set_chip_data()
so the next patch can combine irq_set_chip() and irq_set_handler() to
irq_set_chip_and_handler().
Automated conversion with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Avoid the whole lazy disable dance in the demux handler by providing a
irq_disable() callback.
Use the proper accessor functions and tidy up gpio_irq_handler()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make use of the new functionality which ensures that irq_set_type is
called with the chip masked. Unmask is only done when the interrupt is
not disabled.
Retrieve the trigger type from irq_data in unmask
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the proper accessor function instead of fiddling in the status
bits directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Remove the open coded access to irq_desc which will fail on sparse irq
and use the proper wrappers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The conversion missed, that one of the irq functions is called from
the init code. Split it out, so the irq number based call works.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit 9eac6d0 (ARM: Remove dependency of plat-orion GPIO code on mach
directory includes) missed to convert one instance of
DOVE_GPIO_VIRT_BASE and left the orion_gpio_init() in mpp.c
Fix it up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
MFD changes in 4ec1b54c ('mfd: mfd_cell is now implicitly available to
mc13xxx drivers') changed the mc13xxx_platform_data struct layout.
At the time all users were changed, but this driver was introduced in
another tree at the same time. This updates the mc13xxx_platform_data
user, fixing a build error.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'irq-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
vlynq: Convert irq functions
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq; Fix cleanup fallout
genirq: Fix typo and remove unused variable
genirq: Fix new kernel-doc warnings
genirq: Add setter for AFFINITY_SET in irq_data state
genirq: Provide setter inline for IRQD_IRQ_INPROGRESS
genirq: Remove handle_IRQ_event
arm: Ns9xxx: Remove private irq flow handler
powerpc: cell: Use the core flow handler
genirq: Provide edge_eoi flow handler
genirq: Move INPROGRESS, MASKED and DISABLED state flags to irq_data
genirq: Split irq_set_affinity() so it can be called with lock held.
genirq: Add chip flag for restricting cpu_on/offline calls
genirq: Add chip hooks for taking CPUs on/off line.
genirq: Add irq disabled flag to irq_data state
genirq: Reserve the irq when calling irq_set_chip()
* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
mach-ux500: configure board for the TPS61052 regulator v2
mach-ux500: provide ab8500 init vector
mach-ux500: board support for AB8500 GPIO driver
gpio: driver for 42 AB8500 GPIO pins
handle_prio_irq is almost identical with handle_fasteoi_irq. The
subtle differences are
1) The handler checks for IRQ_DISABLED after the device handler has
been called. In case it's set it masks the interrupt.
2) When the handler sees IRQ_DISABLED on entry it masks the interupt
in the same way as handle_fastoei_irq, but does not set the
IRQ_PENDING flag.
3) Instead of gracefully handling a recursive interrupt it crashes the
kernel.
#1 is just relevant when a device handler calls disable_irq_nosync()
and it does not matter whether we mask the interrupt right away or
not. We handle lazy masking for disable_irq anyway, so there is no
real reason to have this extra mask in place.
#2 will prevent the resend of a pending interrupt, which can result in
lost interrupts for edge type interrupts. For level type interrupts
the resend is a noop in the generic code. According to the
datasheet all interrupts are level type, so marking them as such
will result in the exact same behaviour as the private
handle_prio_irq implementation.
#3 is just stupid. Crashing the kernel instead of handling a problem
gracefully is just wrong. With the current semantics- all handlers
run with interrupts disabled - this is even more wrong.
Rename ack to eoi, remove the unused mask_ack, switch to
handle_fasteoi_irq and remove the private function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
LKML-Reference: <20110202212552.299898447@linutronix.de>
The current mainline codes of ARCH_S5P64X0 and ARCH_S5P6442
can not support suspend to ram. So needs this for preventing
build error on them.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes CPU idmask of S5P64X0 and EXYNOS4210
and its comparison method because just want to use CPU
id for it.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix incorrect conditional execution of ldr instructions in
addruart macro.
Signed-off-by: Thomas Abraham <thomas.abraham@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes smsc9215 irq ploarity configuration of SMDKC210.
We can change type of EINT(5) as HIGH, but it's better to change
IRQ output of smsc9215 as an active low because smsc's IRQ line
has been pull-up.
Signed-off-by: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes smsc9215 irq ploarity configuration of SMDKV310.
We can change type of EINT(5) as HIGH, but it's better to change
IRQ output of smsc9215 as an active low because smsc's IRQ line
has been pull-up.
Signed-off-by: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes following build warnings.
warning: (MACH_ARMLEX4210) selects SATA_AHCI_PLATFORM
which has unmet direct dependencies (ATA)
And adds EXYNOX4_DEV_AHCI for building machines which are
not suppoort for AHCI feature on board.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This change is intended to correct security subsystem interrupt names
for Samsung S5PV210 and S5PC110 SoCs.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The array size parameter of iotable_init for S5P6450 is incorrect.
Fix this by passing the correct length of s5p6450_iodesc table.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This registers the TPS61052 regulator to the ux500 MOP/HREF boards.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds an ab8500 regulator initialization vector for the
HREF/MOP500 series of boards. This also sets the display
regulator to be on at boot so we don't loose our splash
screen when the board comes up.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the board support patch for ab8500 gpio driver
on mach-ux500.Patch implements 16 virtual
IRQ mapped to 16 interrupt capable AB8500 GPIOs.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
[Modify for header file placement]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Nicolas Pitre