At probe time, falcon_reset_hw() performs a hard reset of the PHY
along with Falcon. There is no need to perform a soft reset later,
and any access to standard MDIO registers before the PHY firmware has
booted can interrupt the boot process, making the port unusable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the newly-added generic MDIO clause 45 support and remove
redundant definitions.
Add an 'efx_' prefix to the remaining driver-specific MDIO functions
and remove arguments which are redundant with efx->mdio.prtad.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new PHY supporting SFP+ modules, used in the SFN4112F
reference design. It is similar to the QT2022C2 and shares much of
its support code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shuffle bits of the OUI into the conventional written order.
Replace PHY id component macros with functions.
Zero-pad PHY id components in log messages.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the PHY type names are overly generic. Change them to include
the model numbers of the PHYs they represent.
Correct the model number reference at the top of xfp_phy.c.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
MAC, PHY and board events may be separately enabled and signalled.
Our current arrangement of chaining the polling functions can result
in events being missed. Change them to be more independent.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure for auto-negotiation of speed, duplex and flow
control.
When using 10Xpress, auto-negotiate flow control. While we're
at it, clean up the code to warn when partner is not 10GBASE-T
capable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFC4000 has a separate MAC for use at sub-10G speeds. Introduce
an efx_mac_operations structure with implementations for the two MACs.
Switch between the MACs as necessary.
PHY settings are independent of the MAC, so add get_settings() and
set_settings() to efx_phy_operations. Also add macs field to indicate
which MACs the PHY is connected to.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine DEVS0 and DEVS1 registers into a 32-bit mask instead of
reading just DEVS0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace efx_nic::link_options bitfield with link_speed (speed in
Mbit/s) and link_fd (full duplex flag).
Remove broken auto-negotiation functions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add board monitoring to periodic work whenever link is down.
For SFE4001, report when a fault has caused the PHY to turn off.
For SFE4002, switch XFP PHY into low-power state in case of a fault.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There was a bug in XAUI synchronisation in early 10Xpress firmware
versions. This is fixed in released firmware and we do not need to
work around it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This allows updating PHY firmware for one interface without removing
all other interfaces handled by the driver.
Replace tx_disabled flags and 10Xpress status enumeration with flags in
enum efx_phy_mode.
Prevent an interface from being brought up while in PHY flash mode.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Replace (cond ? 1 : 0) with cond or !!cond as appropriate, and
(cond ? 0 : 1) with !cond.
Remove some redundant boolean temporaries.
Rename one field that looks like a flag but isn't.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add a set of self-tests accessible thorugh ethtool.
Add hardware loopback and TX disable control code to support them.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver supports the 10Xpress PHY and XFP modules on our reference
designs SFE4001 and SFE4002 and the SMC models SMC10GPCIe-XFP and
SMC10GPCIe-10BT.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings