Provide a new file 'name' in the regulator sysfs class with a human
readable name for the regulator for use in applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8400 provides two programmable DCDC step-down (buck) convertors
and four low-dropout (LDO) regulators. This driver provides support for
runtime managment of these in the standard regulator API.
Support for configuration of the suspend and hibernate mode behaviour
of the regulators is not yet included.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the machine constraints mark a regulator as always_on but this was
not done by the bootloader then enable the regulator when applying
constraints.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Try to find a human readable name for the regulator we're failing on and
print a specific diagnostic when we fail to set the suspend state.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Since it is now mandatory to supply constraints via init_data on device
registration check for that when registering, saving us from oopsing
later on.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This improves the machine level API in order to configure
regulator constraints and consumers as platform data and removes the
old string based API that required several calls to set up each regulator.
The intention is to create a struct regulator_init_data, populate
it's fields with constraints, consumers devices, etc and then register
the regulator device from board.c in the standard Linux way.
e.g. regulator LDO2 (supplying codec and sim) platform data.
/* regulator LDO2 consumer devices */
static struct regulator_consumer_supply ldo2_consumers[] = {
{
.dev = &platform_audio_device.dev,
.supply = "codec_avdd",
},
{
.dev = &platform_sim_device.dev,
.supply = "sim_vcc",
}
};
/* regulator LDO2 constraints */
static struct regulator_init_data ldo2_data = {
.constraints = {
.min_uV = 3300000,
.max_uV = 3300000,
.valid_modes_mask = REGULATOR_MODE_NORMAL,
.apply_uV = 1,
},
.num_consumer_supplies = ARRAY_SIZE(ldo2_consumers),
.consumer_supplies = ldo2_consumers,
};
/* machine regulator devices with thier consumers and constraints */
static struct platform_device wm8350_regulator_devices[] = {
{
.name = "wm8350-regulator",
.id = WM8350_LDO_2,
.dev = {
.platform_data = &ldo2_data,
},
},
};
Changes in detail:-
o Removed all const char* regulator config functions in machine API.
o Created new struct regulator_init_data to contain regulator
machine configuration constraints and consmuers.
o Changed set_supply(), set_machine_constraints(),
set_consumer_device_supply() to remove their string identifier
parameters. Also made them static and moved functions nearer top of
core.c.
o Removed no longer used inline func to_rdev()
o Added regulator_get_init_drvdata() to retrieve init data.
o Added struct device* as parameter to regulator_register().
o Changed my email address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This adds a regulator driver for the TI bq24022 Single-Chip
Li-Ion Charger with its nCE and ISET2 pins connected to GPIOs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
This patch adds kernel build support for the regulator core.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
This provides a virtual regulator test harness which exposes a sysfs
interface for setting power requirements, intended for test purposes only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
This adds supports for regulator that are not software controlable. It allows
them to coexist in systems with mixed supplies.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
This adds the regulator framework core.
This framework is designed to provide a generic interface to voltage
and current regulators within the Linux kernel. It's intended to
provide voltage and current control to client or consumer drivers and
also provide status information to user space applications through a
sysfs interface.
The intention is to allow systems to dynamically control regulator
output in order to save power and prolong battery life. This applies
to both voltage regulators (where voltage output is controllable) and
current sinks (where current output is controllable).
This framework safely compiles out if not selected so that client
drivers can still be used in systems with no software controllable
regulators.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown