This patch (as1365) enables remote wakeup by default for USB keyboard
devices. Keyboards in general are supposed to be wakeup devices, but
the correct place to enable it depends on the device's bus; no single
approach will work for all keyboard devices. In particular, this
covers only USB keyboards (and then only those supporting the boot
protocol).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add framebuffer support to PicoLCD device with use of deferred-io.
Only changed areas of framebuffer get sent to device in order to
save USB bandwidth and especially resources on PicoLCD device or
allow higher refresh rate for a small area. Changed tiles are
determined while updating shadow framebuffer.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Move the initialization of USB interface pointers from _start()
over to _probe() callback, which is where it belongs.
This fixes case where interface is NULL when parsing of report
descriptor fails.
LKML-Reference: <20100213135720.603e5f64@neptune.home>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some devices do not react to a control request (seen on APC UPS's) resulting in
a slow stream of messages, "generic-usb ... control queue full". Therefore
request needs a timeout.
Cc: stable@kernel.org
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device generates ABS_Z and ABS_RX events, while it should be
generating ABS_X and ABS_Y instead. Using the MULTI_INPUT quirk solves
this issue.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Daniel Oliveira Nascimento <don@syst.com.br>
[jkosina@suse.cz: fixed blacklist ordering while resolving conflict]
[jkosina@suse.cz: fixed typo to make it compile]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In commit 2da31939a4 ("Bluetooth: Implement raw output support for HIDP
layer"), support for Bluetooth hid_output_raw_report was added, but it
pushes the data to the intr socket instead of the ctrl one. This has been
fixed by 6bf8268f9a ("Bluetooth: Use the control channel for raw HID reports")
Still, it is necessary to distinguish whether the report in question should be
either FEATURE or OUTPUT. For this, we have to extend the generic HID API,
so that hid_output_raw_report() callback provides means to specify this
value so that it can be passed down to lower level hardware drivers (currently
Bluetooth and USB).
Based on original patch by Bastien Nocera <hadess@hadess.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device generates ABS_Z and ABS_RX events, while it should be
generating ABS_X and ABS_Y instead. Using the MULTI_INPUT quirk solves
this issue.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Daniel Oliveira Nascimento <don@syst.com.br>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I happen to own a keyboard identified as 05af:3062 which is labeled as
"FlatX Coldless Combo" by "Prodige", which exhibits input problems without
NOGET quirk. For some reason, lsusb reports this device as "Jing-Mold
Enterprise Co., Ltd", which is not mentioned anywhere on the package.
A quick search on the intenet shows that there a other people who have
this in their lsusb output, but apparently they don't have the problem
I am seeing (or they are not such furious typists as myself).
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1302) removes the auto_pm flag from struct usb_device.
The flag's only purpose was to distinguish between autosuspends and
external suspends, but that information is now available in the
pm_message_t argument passed to suspend methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
These touchscreens are mounted onto HP TouchSmart and the Dell Studio One
19. Without a quirk they report a wrong button set and the x/y coordinates
through ABS_Z/ABS_RX, confusing the higher levels (most notably X.Org's
evdev driver).
Device id 0x003 covers models 1900, 2150, and 2700 [1] though testing could
only be performed on a model 1900.
[1] http://www.nextwindow.com/nextwindow_support/latest_tech_info.html
Signed-off-by: Peter Hutterer <peter.hutterer@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use strlcat() to append a string to the previously created first part.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The race between ioctl and disconnect is guarded by low level
hiddev device mutex (existancelock) since the commit
07903407 ("HID: hiddev cleanup -- handle all error conditions
properly"), therefore we can remove the lock_kernel() from
hiddev_ioctl_usage().
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
NCR devices are terminally broken by design -- they claim themselves to contain
proper input applications in their HID report descriptor, but behave very badly
if treated in standard way.
According to NCR developers, the devices get confused when queried for reports
in a standard way, rendering them unusable.
NCR is shipping application called "RPSL" that can be used to drive these
devices through hiddev, under the assumption that in-kernel driver doesn't
perform initial report query.
If it does, neither in-kernel nor hiddev-based driver can operate with these
devices any more.
Introduce a quirk that skips the report query for all NCR devices. The previous
NOGET quirk was wrong and had been introduced because I misunderstood the nature
of brokenness of these devices.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When encountering a strange value in the pool report, pidff_reset
will always refetch the report 20 times, even if one of the retries
results in a sane value. This is because a temporary variable being
used to store the value is not being updated inside the loop.
Fix it by using the value directly in the loop.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch was applied to Fedora 11's 2.6.30.8-64 kernel and adds the
NOGET quirk for CH Products industrial class joystick(s). It is like
the previous CH Products NOGET quirk patch for their consumer class
joysticks. Without the quirk, the joystick would only be detected and
would not function at all in kernels >= 2.6.29. It was tested with a CH
Products 3-axis 5-button industrial joystick, product #HG-434IS000-U-217.
Signed-off-by: Keith Rutkowski <rutkowski@signatureresearchinc.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove unused (in usbhid module) DRIVER_AUTHOR macrco and properly
use multiple MODULE_AUTHOR() instances in both modules.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
HID core registers input, hidraw and hiddev devices, but leaves
unregistering it up to the individual driver, which is not really nice.
Let's move all the logic to the core.
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Reported-by: Brian Rogers <brian@xyzw.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hiddev userspace driver uses a rignbuffer to store the parsed usages
that should be returned through read(). This buffer is 64 bytes long,
which is sufficient for queueing single USB 1.0 low-speed report, which
is of maximum size 48 bytes.
There are however USB HID devices which are full-speed USB devices, and
therefore they are free to produce reports 64 bytes long. This is correctly
handled by HID core, but read() on hiddev node gets stuck forever, because
the ring buffer loops infinitely (as it is exactly 64 bytes long as well),
never advancing the buffer pointer.
Plus, the core driver is ready to handle highspeed devices, so we should be
able to handle reports from such devices in the hiddev driver as well, which
means we need larger ringbuffer.
Reported-by: Michael Zeisel <michael.zeisel@philips.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
__usbhid_submit_report() is a local function wrapped by the exported
symbol usbhid_submit_report(). As such, it should be static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Check whether index is within bounds before testing the element.
declared in drivers/hid/usbhid/hid-core.c:62:
static char *quirks_param[MAX_USBHID_BOOT_QUIRKS] = ...
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for USB drivers to report their requested nodename to
userspace. It also updates a number of USB drivers to provide the
needed subdirectory and device name to be used for them.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is a little bit inconvenient for people who have some non-standard
HID hardware (usually violating the HID specification) to have to
recompile kernel with CONFIG_HID_DEBUG to be able to see kernel's perspective
of the HID report descriptor and observe the parsed events. Plus the messages
are then mixed up inconveniently with the rest of the dmesg stuff.
This patch implements /sys/kernel/debug/hid/<device>/rdesc file, which
represents the kernel's view of report descriptor (both the raw report
descriptor data and parsed contents).
With all the device-specific debug data being available through debugfs, there
is no need for keeping CONFIG_HID_DEBUG, as the 'debug' parameter to the
hid module will now only output only driver-specific debugging options, which has
absolutely minimal memory footprint, just a few error messages and one global
flag (hid_debug).
We use the current set of output formatting functions. The ones that need to be
used both for one-shot rdesc seq_file and also for continuous flow of data
(individual reports, as being sent by the device) distinguish according to the
passed seq_file parameter, and if it is NULL, it still output to kernel ringbuffer,
otherwise the corresponding seq_file is used for output.
The format of the output is preserved.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
No more reinitialization is needed in the post reset hook, remove
the FIXME comment.
While at it, clean up whitespaces in the immediate surrounding.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1240) adds the NOGET quirk for three devices from CH
Products: the Pro pedals, the Combatstick joystick, and the Flight-Sim
yoke. Without these quirks, the devices haven't worked for many
kernel releases. Sometimes replugging them after boot-up would get
them to work and sometimes they wouldn't work at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Sean Hildebrand <silverwraithii@gmail.com>
Reported-by: Sid Boyce <sboyce@blueyonder.co.uk>
Tested-by: Sean Hildebrand <silverwraithii@gmail.com>
Tested-by: Sid Boyce <sboyce@blueyonder.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Device-specific quirks are set up correctly in their respective vendor-specific
driver, then get overwritten in usbhid_parse().
This is only issue for device-specific NOGET quirks being set by driver for a
few devices out there.
Signed-off-by: Zoltan Karcagi <zkr@freemail.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch switches usbhid_close() from flush_scheduled_work() to canceling
the outstanding work. This fixes a possible deadlock due to work taking
the mutex usbhid_close() holds. Lockdep reported the problem.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
--
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
upon further thought this code is still racy.
retval = usb_register_dev(usbhid->intf, &hiddev_class);
here you open a window during which open can happen
if (retval) {
err_hid("Not able to get a minor for this device.");
hid->hiddev = NULL;
kfree(hiddev);
return -1;
} else {
hid->minor = usbhid->intf->minor;
hiddev_table[usbhid->intf->minor - HIDDEV_MINOR_BASE] = hiddev;
and will fail because hiddev_table hasn't been updated
The obvious fix of using a mutex to guard hiddev_table doesn't work because
usb_open() and usb_register_dev() take minor_rwsem and we'd have an AB-BA
deadlock. We need a lock usb_open() also takes in the right order and that leaves
only one option, BKL. I don't like it but I see no alternative.
Once the usb_open() implements something better than lock_kernel(), we could also
do so.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When hid quirks were converted to specialized driver, the HID_QUIRK_IGNORE
has been moved completely, as the hid_ignore_list[] has been moved into the
generic code.
However userspace already got used to the possibility that modprobing
usbhid with
'quirks=vid:pid:0x4'
makes the device ignored by usbhid driver. So keep this quirk flag in place
for backwards compatibility.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'bkl-removal' of git://git.lwn.net/linux-2.6:
Rationalize fasync return values
Move FASYNC bit handling to f_op->fasync()
Use f_lock to protect f_flags
Rename struct file->f_ep_lock
This fixes a use of flush_scheduled_work() in USB HID's reset logic that can
deadlock.
Tested-by: Valdis Kletniks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no point of having hid_reset_resume() when CONFIG_PM is
not set, and even the corresponding .reset_resume pointer in hid_driver
struct is properly ifdefed.
Move the definition into the ifdef CONFIG_PM part of the source to avoid
drivers/hid/usbhid/hid-core.c:1337: warning: 'hid_reset_resume' defined but not used
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes a bug caused by reset_resume not changing the internal
status flags for a device that is resumed via reset_resume. To do so the
reset handlers, which correctly assume that a device is awake, can no longer
do all the work of reset_resume handling.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixes this build breakage in case when CONFIG_PM is not set
drivers/hid/usbhid/hid-core.c: In function 'hid_suspend':
drivers/hid/usbhid/hid-core.c:1220: error: 'struct usb_device' has no member named 'auto_pm'
drivers/hid/usbhid/hid-core.c:1245: error: 'struct usb_device' has no member named 'auto_pm'
drivers/hid/usbhid/hid-core.c:1258: error: 'struct usb_device' has no member named 'auto_pm'
by throwing both the hid_suspend() and hid_resume() away completely
in such case, as they won't be used anyway.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This uses the USB busy mechanism for aggessive autosuspend of USB
HID devices. It autosuspends all opened devices supporting remote wakeup
after a timeout unless
- output is being done to the device
- a key is being held down (remote wakeup isn't triggered upon key release)
- LED(s) are lit
- hiddev is opened
As in the current driver closed devices will be autosuspended even if they
don't support remote wakeup.
The patch is quite large because output to devices is done in hard interrupt
context meaning a lot a queuing and locking had to be touched. The LED stuff
has been solved by means of a simple counter. Additions to the generic HID code
could be avoided. In addition it now covers hidraw. It contains an embryonic
version of an API to let the generic HID code tell the lower levels which
capabilities with respect to power management are needed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Most fasync implementations do something like:
return fasync_helper(...);
But fasync_helper() will return a positive value at times - a feature used
in at least one place. Thus, a number of other drivers do:
err = fasync_helper(...);
if (err < 0)
return err;
return 0;
In the interests of consistency and more concise code, it makes sense to
map positive return values onto zero where ->fasync() is called.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
DECLARE_WAITQUEUE doesn't initialize the wait descriptor's task_list
to 'empty' but to zero.
prepare_to_wait() will not enqueue the descriptor to the waitqueue and
finish_wait() will do list_del_init() on a list head that contains
NULL pointers, which oopses.
This was introduced by 079034073 "HID: hiddev cleanup -- handle all
error conditions properly".
The prior code used an unconditional add_to_waitqueue() which didn't
care about the wait descriptor's list head and enqueued the thing
unconditionally.
The new code uses prepare_to_wait() which DOES check the prior list
state, so use DEFINE_WAIT instead.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If hiddev_open() fails, it wrongly frees the shared hiddev structure
kept in hiddev_table instead of the hiddev_list structure allocated
for the opened file descriptor. Existing references to this structure
will then accessed free memory.
This was introduced by 079034073 "HID: hiddev cleanup -- handle all
error conditions properly".
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The logic for testing for disconnection is reversed in an ioctl leading
to false reports of disconnection.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
Commit 079034073f ("HID: hiddev cleanup -- handle all error conditions
properly") by mistake removed proper initialization of hid->hiddev pointer
in hiddev_connect() in case usb_register_dev() succeeds for the hiddev node.
Put it properly back in place.
Reported-and-tested-by: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1161) changes the interface to
usb_lock_device_for_reset(). The existing interface is apparently not
very clear, judging from the fact that several of its callers don't
use it correctly. The new interface always returns 0 for success and
it always requires the caller to unlock the device afterward.
The new routine will not return immediately if it is called while the
driver's probe method is running. Instead it will wait until the
probe is over and the device has been unlocked. This shouldn't cause
any problems; I don't know of any cases where drivers call
usb_lock_device_for_reset() during probe.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Genius PenSketch 12x9 tablet has a puck (labeled a
"Tablet Mouse") in addition to a pen. Without registering a quirk
the tablet appears to be a single input device that reports the
wrong axis information in /proc/bus/input/devices, and sends
incorrect events (e.g. ABS_Z instead of ABS_Y). This information
confuses the X evdev driver and makes the device impossible to
use.
The quirk fixes events and splits the device into multiple input
event devices so that at least the puck is useful.
Signed-off-by: Matt Helsley <matt.helsley@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The usbmouse and usbkbd modules are not supposed to be used with regular USB
mice and keyboards. Make them depend on EMBEDDED to prevent them from being
built and loaded on non-EMBEDDED configs.
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a cleanup of hiddev and fixes the following issues:
- thread safety by locking in read & ioctl, introducing a per device mutex
- race between ioctl and disconnect, introducing a flag and locking
in form of a per low level device mutex
- race between open and other methods, making sure only successfully
opened devices are put on the list, changing order of events
- range checking both upper and lower limits of the minor range
- make sure further calls to open fail for unplugged devices even if
the device still has opened files
- error checking for low level open
- possible loss of wakeup events, using standard waiting macros
- race in initialisation by moving registration after full initialisation
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We might sleep, so no problem to use GFP_KERNEL.
While at it bring the function to coding style.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use usb_endpoint_xfer_int() instead of direct use of constants.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move usbhid specific flags from global hid.h into local usbhid.h.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1146c) makes usbhid automatically call usbhid_set_leds()
for any device that supports the keyboard boot protocol.
In theory this should be perfectly safe. BIOSes send the LED output
report as part of their normal device initialization, so any keyboard
device supporting the boot protocol has to be able to handle it.
As a side effect, the hid-dell and hid-bright drivers are no longer
needed, and the Logitech keyboard driver can be removed from hid-lg.
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When computing the maximal buffer size needed, we must take into
account that not only input reports can be numbered.
Pointed out in bugzilla #10467
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It causes recursive locking warning and is unneeded after
introduction of STARTED flag.
* Resume vs. stop is effectively solved by DISCONNECT flag.
* No problem in suspend vs. start -- urb is submitted even after open
which is possible after connect which is called after start.
* Resume vs. start solved by STARTED flag.
* Suspend vs. stop -- no problem in killing urb and timer twice.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some devices have no input interrupt endpoint. These won't be handled
by usbhid, but currently they are not refused and reside on hid bus.
Perform this checking earlier so that we refuse to control such
a device early enough (and not pass it to the hid bus at all).
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
`stop' left out usbhid->urb* pointers and so the next `start' thought
it needs to allocate nothing and used the memory pointers previously
pointed to. This led to memory corruption and device malfunction.
Also don't forget to clear disconnect flag on start which was left set
by the previous `stop'.
This fixes
echo DEVICE > /sys/bus/hid/drivers/DRIVER/unbind
echo DEVICE > /sys/bus/hid/drivers/DRIVER/bind
failures.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When suspending, make sure that the timer is not running
any more.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Usbhid structure is allocated on start invoked only from probe
of some driver. When there is no driver, the structure is null
and causes null-dereference oopses.
Fix it by allocating the structure on probe and disconnect of
the device itself. Also make sure we won't race between start
and resume or stop and suspend respectively.
References: http://bugzilla.kernel.org/show_bug.cgi?id=11827
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Andreas Schwab <schwab@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add support for Sony Vaio VGX-TP1E
HID: fix lock imbalance in hiddev
HID: fix lock imbalance in hidraw
HID: fix hidbus/appletouch device binding regression
HID: add hid_type to general hid struct
HID: quirk for OLED devices present in ASUS G50/G70/G71
HID: Remove "default m" for Thrustmaster and Zeroplus
HID: fix hidraw_exit section mismatch
HID: add support for another Gyration remote control
Revert "HID: Invert HWHEEL mappings for some Logitech mice"
Add type to the hid structure to distinguish to which device type
(now only mouse) we are talking to. Needed for per device type ignore
list support.
Note: this patch leaves the type as unknown for bluetooth devices,
there is not support for this in the hidp code.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There were two stragglers that got missed in the last merge of the HID tree that forgot to change the warn() calls to dev_warn(). This patch fixes them up.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 8006479c9b introduced a spinlock in
input_dev->event_lock, which is locked when handling input events.
However, the hid-pidff driver sleeps when handling events as it waits for
reports being sent to the device before changing the report contents
again.
This causes a system lockup when trying to use force feedback with a PID
device, a regression introduced in 2.6.24 and 2.6.23.15.
Fix it by extracting the raw report data from struct hid_report
immediately when hid_submit_report() is called, therefore allowing
drivers to change the contents of struct hid_report immediately without
affecting the already-queued transfer.
In hid-pidff, re-add the removed usbhid_wait_io() to
pidff_erase_effect() instead, to prevent a full report queue from causing
the submission to fail, thus not freeing up device memory.
pidff_erase_effect() is not called while dev->event_lock is held.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid-ff.c now calls only pidff (generic driver), the special ones are now
in separate drivers. Invoke pidff on all non-special directly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move the force feedback processing into a separate module.
[jkosina@suse.cz: fix Kconfig texts a little bit]
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This seems to be the very same device, as already supported Smartjoy
dual Plus, but with slightly different vendor ID. Let's support this
one too.
Reported-by: David Ashley <dashxdr@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge the logitech force feedback processing directly into logitech
driver from the usbhid core.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move the handling of the leds resetting from the core to
the dell and logitech drivers.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move connecting from usbhid to the hid layer and fix also hidp in
that manner.
This removes all the ignore/force hidinput/hiddev connecting quirks.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove support for both dynamic and static report descriptor
quirks. There is no longer rdesc code which it would support,
so it's useless.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bring switch and cases into coding style and save thus some
indentation to make the code tighter.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move ignore quirks from usbhid-quirks into hid-core code. Also don't output
warning when ENODEV is error code in usbhid and try ordinal input in hidp
when that error is returned.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move ids from hid-quirks.c into separate file, since it will be needed in
more than one place.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Next step for complete hid bus, this patch includes:
- call parser either from probe or from hid-core if there is no probe.
- add ll_driver structure and centralize some stuff there (open, close...)
- split and merge usb_hid_configure and hid_probe into several functions
to allow hooks/fixes between them
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make a bus from hid core. This is the first step for converting all the
quirks and separate almost-drivers into real drivers attached to this bus.
It's implemented to change behaviour in very tiny manner, so that no driver
needs to be changed this time.
Also add generic drivers for both usb and bt into usbhid or hidp
respectively which will bind all non-blacklisted device. Those blacklisted
will be either grabbed by special drivers or by nobody if they are broken at
the very rude base.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver adds support for the multitouch trackpad on the new
Apple Macbook Air and Macbook Pro Penryn laptops. It replaces the
appletouch driver on those computers, and integrates well with the
synaptics driver of the Xorg system.
[dtor@mail.ru: various cleanups]
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch completely removes the dependency of usbkbd and usbmouse drivers
on usbhid code.
usbkbd/usbmouse drivers are not needed in the vast majority of cases anyway,
and they shouldn't be loaded in standard configurations at all. They are supposed
to be as trivial as possible, and searching for HID_QUIRK_IGNORE can even be
bad in some cases.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Logitech DiNovo desktop needs the same quirk as other DiNovo
devices.
Reported-by: Farid Benamrouche <farid.benamrouche@free.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When usbmouse/kbd is set to build, USB_HID is never defined due to
the USB_HID!=y Kconfig rule. Test CONFIG_USB_HID_MODULE in both
drivers instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Logitech mice have a tilt wheel which register as HWHEEL buttons.
The events are positive for a click to the right and negative for a
click to the left. Applications expect the opposite, though.
I suspect this affects a lot more Logitech mice, but these are the only
two I have. I tested this using evtest and a GTK application. A similar
Microsoft Intellimouse I have works correctly.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added device ids to hid-quriks for detection of keyboards on 4th
generation Macbook Pro and Macbook Air
The naming scheme is consistent with past Apple keyboards in hid-quirks;
as defined by Apple (including device ids) in:
/System/Library/Extensions/AppleUSBTopCase.kext/Contents/PlugIns/AppleUSBTCKeyboard.kext/Co
ntents/Info.plist
Patch was originally posted and tested at:
https://bugs.launchpad.net/mactel-support/+bug/207127
Signed-off-by: Alexandre Karpenko <alexander@comm.utoronto.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix build failure introduced by Alan's ioctl -> unlocked_ioctl
(pushing BKL down to the driver) conversion patch for hiddev.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Push down the BKL. In some cases compat_ioctl already doesn't take the
BKL so we don't either. Some of the locking here seems already dubious
and object lifetimes want documenting
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch renames the existing usb_reset_device in hub.c to
usb_reset_and_verify_device and renames the existing
usb_reset_composite_device to usb_reset_device. Also the new
usb_reset_and_verify_device does't need to be EXPORTED .
The idea of the patch is that external interface driver
should warn the other interfaces' driver of the same
device before and after reseting the usb device. One interface
driver shoud call _old_ usb_reset_composite_device instead of
_old_ usb_reset_device since it can't assume the device contains
only one interface. The _old_ usb_reset_composite_device
is safe for single interface device also. we rename the two
functions to make the change easily.
This patch is under guideline from Alan Stern.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
From the current implementation of usb_reset_composite_device
function, the iface parameter is no longer useful. This function
doesn't do something special for the iface usb_interface,compared
with other interfaces in the usb_device. So remove the parameter
and fix the related caller.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The new iMON LCDs from SoundGraph need to be blacklisted from HID in order to
be used by lirc.
Signed-off-by: Dylan R Semler <dylan.semler@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since 2.6.25 the HID_QUIRK_APPLE_HAS_FN quirk is enabled even for
non-laptop Apple keyboards of the Aluminium series. The USB version of
these don't need Numlock emulation, like the laptop (and Aluminium
Wireless) do, as they have a proper keypad.
This patch splits the Numlock emulation for Apple keyboards in a
different quirk flag, so that it can be enabled for all the keyboards
but the Aluminium USB ones.
If the Numlock emulation is enabled for Aluminium USB keyboards, the
JKL and UIO keys become the numeric pad, and the rest of the keyboard
is disabled, included the key used to disable Numlock.
Additionally, these keyboard should not have a Numlock at all, as the
Numlock key is instead replaced by the 'Clear' key as usual for Apple
USB keyboards.
Signed-off-by: Diego 'Flameeyes' Petteno <flameeyes@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
usb_control_msg() converts arguments to little-endian itself,
doing that in caller means breakage on big-endian boxen.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo in report descriptor fixup, which results in improper
substitution and leaving old value in place.
Reported-by: Juha Motorsportcom <juha_motorsportcom@luukku.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Samsung USB remotes (0419:0001) report six keys via standard HID usage pages
(arrow keys, OK, Power). Kernel 2.6.25 maps those to input events (in addition
to the hiddev report). The remaining 43 keys are reported via proprietary HID
report page and therefore by hiddev only.
Applications using hiddev and input device might process the 6 standard keys
twice. To avoid this, the input device will be suppressed for the Samsung
remote with a quirk entry, forcing to use the hiddev device only.
LIRC already contains the proper support.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jeremy Robertson reports that GTCO engineers made a mistake and we don't
need 0x60x GTCO product ids blacklisted.
This mostly reverts dda3fd35, but leaves PID 0x1007 intact.
Reported-by: Jeremy Roberson <jeremy.roberson@einstruction.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no need to keep a few years old ThrustMaster force-feedback
driver as experimental.
HID_FF is currently marked experimental anyway, so this is even redundant.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a window:
task A task B
spin_lock_irq(&usbhid->inlock); /* Sync with error handler */
usb_set_intfdata(intf, NULL);
spin_unlock_irq(&usbhid->inlock);
usb_kill_urb(usbhid->urbin);
usb_kill_urb(usbhid->urbout);
usb_kill_urb(usbhid->urbctrl);
del_timer_sync(&usbhid->io_retry);
cancel_work_sync(&usbhid->reset_work);
if (!hid->open++) {
res = usb_autopm_get_interface(usbhid->intf);
if (res < 0) {
hid->open--;
return -EIO;
}
}
if (hid_start_in(hid))
if (hid->claimed & HID_CLAIMED_INPUT)
hidinput_disconnect(hid);
in which an open() to an already disconnected device will submit an URB
to an undead device. In case disconnect() was called by an ioctl, this'll
oops. Fix by introducing a new flag and checking it in hid_start_in().
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch makes the following needlessly global functions static:
- hid-core.c:hid_input_field()
- usbhid/hid-quirks.c:usbhid_modify_dquirk()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This moves the misplaced rdesc quirk to the place where it belongs.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add force feedback support for Logitech Rumblepad 2.
Tested-By: Edgar Simo <bobbens@gmail.com>
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix these sparse warnings:
.../hid/hid-core.c💯15: warning: incorrect type in assignment (different signedness)
.../hid/hid-core.c💯15: expected signed int [usertype] *value
.../hid/hid-core.c💯15: got unsigned int *<noident>
by unsigned -> s32
.../hid/hid-input-quirks.c:336:10: warning: Using plain integer as NULL pointer
by 0 -> NULL
.../hid/usbhid/hid-core.c:786:46: warning: incorrect type in argument 3 (different signedness)
.../hid/usbhid/hid-core.c:786:46: expected int *max
.../hid/usbhid/hid-core.c:786:46: got unsigned int *<noident>
.../hid/usbhid/hid-core.c:787:47: warning: incorrect type in argument 3 (different signedness)
.../hid/usbhid/hid-core.c:787:47: expected int *max
.../hid/usbhid/hid-core.c:787:47: got unsigned int *<noident>
.../hid/usbhid/hid-core.c:788:48: warning: incorrect type in argument 3 (different signedness)
.../hid/usbhid/hid-core.c:788:48: expected int *max
.../hid/usbhid/hid-core.c:788:48: got unsigned int *<noident>
by int -> unsigned int
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This must be the weirdest failure yet. My external disk stops processing
the storage commands the moment it receives a GET_REPORT. The firmware
does not crash; if I do rmmod hid, then SET-INTERFACE restores normal
operations. Still, I cannot live without the keyboard when I want backup
my files. Adding the NOGET quirk fixes this problem for me.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device has reports lower logical maximum compared to the real
usages for Zoom+ and Zoom- it emits.
This patch bumps the values in the report descriptor up, and also
adjusts HID_MAX_USAGE accordingly.
Reported-by: Khelben Blackstaff <eye.of.the.8eholder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft's wireless desktop receiver (Model 1028) has a bug in the report
descriptor -- namely, in four seperate places it uses USAGE_MIN and _MAX when
it quite obviously doesn't intend to.
In other words, it reports that it has pretty much _everything_ in 'consumer'
and 'generic desktop'. And then the X evdev driver believes I have a mouse
with 36 absolute axes and a huge pile of keys and buttons, when I in fact,
should have zero. 255/256 in three of the cases, and 0-1024 in another.
This patch fixes the report descriptor of this device before it enters the HID
parser.
Signed-off-by: Jim Duchek <jim.duchek@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many vendors highspeed devices give erroneously fullspeed interval value in
endpoint descriptor for interrupt endpoints. This quirk fixes up that by
recalculating the right value for highspeed device.
At the time of hid configuration this quirk calculates which highspeed interval
value gives same interval delay as, or next smaller then, what it would be if
the original value would be interpreted as fullspeed value. In subsequent urbs
that new value is used instead.
Forming the 'hid->name' in usb_hid_config() was moved up to accommodate more
descriptive printk reporting the fixup.
In this patch the quirk is set for one such device: Afatech DVB-T 2 infrared
HID-keyboard. It reports value 16 which means 4,069s in highspeed while
obviously 16ms was intended. In this case quirk calculates new value to be 8
which gives when interpreted as highspeed value 16ms as wanted. The behavior of
the device was verified to be what expected both before and after the patch.
Signed-off-by: Pekka Sarnila <sarnila@adit.fi>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Alan Stern