This adds support for the foolowing Wacom devices:
- 0x9F - a single touch only LCD tablet;
- 0xE2 - a two finger touch only LCD tablet;
- 0xE3 - a two finger touch, penabled LCD tablet.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Call wacom_query_tablet_data() from wacom_resume() so the device will be
switched to Wacom mode upon resume. Devices that require this are: regular
tablets and two finger touch devices.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We can't use msleep() while holding a spinlock, moreower serio's write()
method is supposed to be useable from inettrupt context. Let's do what
i8042 does and poll the status register every 50 us (with udelay).
Reported-by: Marjan Fojkar <marjan@pajkc.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Gigabyte netbook model M1022M requires i8042.noloop, otherwise AUX port
will not detected and the touchpad will not work. Unfortunately chassis
type in DMI set to "Other" and thus generic laptop entry does not fire
on it.
Reported-by: Darryl Bond <dbond@nrggos.com.au>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some hardware (such as Dell laptops) signal a variety of events through
the i8042 controller, even if these don't map to keyboard events. Add
support for drivers to filter the i8042 event stream in order to respond
to these events and (if appropriate) block them from entering the input
stream.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to protect not only i8042 status and data register from concurrent
access from IRQ 1 and 12 but the rest of the shared state as well, so let's
move release of i8042_lock in i8042_interrupt() a little bit further down.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Relative events are only reported via secondary device therefore device
associated with the touchpad should not advertise these capabilities.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Mark altera_ps2_probe() as __devinit and altera_ps2_remove() as __devexit
so that they can be discarded when not needed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
del_timer() does not wait for the timer to finish running before returning
and therefore is technically not safe. Also make sure to enable tasklet
before kicking timer that will schedule it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Setting up owner field ensures that driver core creates symlink from
the driver to a module implementing this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
More and more devices choose to reimplement support for sparse keymaps
first introduced by wistron driver. Move it into a library module so it
can be easily used by interested parties.
Reviewed-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver does not reference identification strings in DMI table and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver does not reference identification strings in DMI tables and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver does not reference identification strings in DMI table and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver does not reference identification strings in DMI tables and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
DMI tables use considerable amount of memory. Mark them as __initconst
so they will be discarded once module is loaded.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
These laptops often leave i8042 in a wierd state resulting in non-
operational touchpad and keyboard.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keyboard handler should not attempt to traverse handler->h_list on
its own, without any locking, otherwise it races with registering
and unregistering of input handles which leads to crashes.
Introduce input_handler_for_each_handle() helper that allows safely
iterate over all handles attached to a particular handler and switch
keyboard handler to use it.
Reported-by: Jim Paradis <jparadis@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to read and report gpio state when we bind the driver to the
device and upon resume so that userspace has correct state of the
switches (and keys but they are less important since, even if they
are happened to be pressed, we'd expect them to be released fairly
soon).
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for the ET&T TC5UH 5-wire USB touchscreen controller.
More info at http://www.etandt.com.tw/board_solution.html
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Added two new Xbox 360 devices:
- HORI Real Arcade Pro.EX
- Mad Catz SFIV Fightpad
Signed-off-by: Nicolas Léveillé <nicolas@uucidl.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If the poll interval is set to 0 via new sysfs entry and device is
opened after that, polling is started with interval 0. This causes
huge CPU load. Same happens if the rate was 0 when the device was
closed and then reopened.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It does not make sense to wait poll_interval before performing first
read after opening the device, schedule the read immediately instead.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
S3C24XX touchscreen driver, originally written by Arnaud Patard and
other contributors. The driver has had substantial testing as well as
a number of tidying up passes done by Ben Dooks, as noted:
- added kernel-doc comments to most of the routines
- removed old code from pre adc framework days
- updated device probe code to use platform id list matching
- cleaned up debug, since printk() now has timestamp feature
- ensure code uses dev_() reporting macros where necessary
- remove ABS_PRESSURE reporting, tslib can be fixed
- ensure timer is removed on driver exit
- move to using dev_pmops for power management
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Zytronic USB-attached capacitive touchscreen support within the generic
USB touchscreen driver.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Function name is input_ff_destroy() and not input_ff_free()
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use strlcat() to append a string to the previously created first part.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On Zaurus, hx4700 and others pressure is reported inverted -- the lighter
the pressure, the bigger numerical value.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
usb_kill_urb() in disconnect is not needed as unregistering will cause
close() to be called.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
New at91sam9g45ekes board provides a LCD with resistive touchscreen.
This is the support of this feature by atmel_tsadcc driver. This also
sets up platform parameters to be passed to the driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a number of plafrom dependent parameters to atmel_tsadcc. The
touchscreeen driver can now take into account the slight differences
that exist between IPs included in diferent products. This will also
allow to adapt its behaivior to the caracteristics of the resistive
panel used.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tiny patch for setting capabilities using input API function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The touchpad on Acer Aspire 5720, 5520 and some other Aspire models
(signature 0x73, 0x02, 0x50) has a button that can be rocked in 4
different directions. Make the driver to generate BTN_0..BTN_3 events
in response. The Synaptics driver by default maps BTN_0 and BTN_1 to
up and down, so there should be no visible changes with the old setup
that generated BTN_FORWARD and BTN_BACK (also mapped to up and down).
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not start protocol detection assuming that middle mouse is present,
instead let individual protocols explicitly set this capability.
This fixes issue with Synaptics touchpads pretending that they have
middle button when hardware clearly reports otherwise.
Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The main input device of Lifebook touchscreens does not generate
left/right/middle button events and therefore should not be advertising
them in its capabilities.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Elantech touchpads work in absolute mode and do not generate relative
events so they should not be advertising them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Touchkit PS/2 touchscreen does not have left/right/middle buttons and
should not be advertising as capable of generating these events.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sysfs entry for reading and setting of the polling interval. If the
interval is set to 0, polling is stopped. Polling is restarted when
interval is changed to non-zero.
sysfs entries:
poll = current polling interval in msec (RW)
max = max allowed polling interval (RO)
min = min allowed polling interval (RO)
Minimum and maximum limit for interval can be set while setting up the
device.
Interval can be adjusted even if the input device is not currently open.
[dtor@mail.ru: add kernel doc markup for the new fields]
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move the code that deals with setting up each individual button out into
a new function to reduce the indentation and allow us to common up some
of the error recovery code.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Ping Cheng