We use well known standard names for functions that have name, such as
I2C, SPI, SPDIF, etc..
Fix the function name of SPDIF, which was named OWA (One Wire Audio)
based on Allwinner datasheets.
Fixes: 4730f33f0d ("pinctrl: sunxi: add allwinner A83T PIO controller
support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi pinctrl driver currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner pin controllers are also GPIO controllers.
Currently, if GPIOLIB is forgot to be chosen, the build of
pinctrl-sunxi.c will fail for lacking a lot of gpiochip_* functions.
Select GPIOLIB to ensure this driver can be built.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A64 has a R_PIO pin controller, similar to the one found on the H3 SoC.
Add support for the pins controlled by the R_PIO controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARM64 Allwinner SoCs used to have every pinctrl driver selected in
ARCH_SUNXI. Change this to make their default value to (ARM64 &&
ARCH_SUNXI).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Switch the generic pin config argument from 16 to 24 bits,
only use 8 bits for the configuration type. We might need to
encode more information about a certain setting than we need
to encode different generic settings.
- Add a cross-talk API to the pin control GPIO back-end,
utilizing pinctrl_gpio_set_config() from GPIO drivers that
want to set up a certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the
GPIO chips, so that they pass a generic configuration for
things like debouncing and single ended (typically open
drain). This change has also been merged in an immutable
branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing
a pin controller before trying to get any hogs.
- For pin controllers putting all group and function definitions
into the device tree, we now have generic code to deal with
this and it is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down.
New subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in
the LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on
GPIOs. Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode.
STM32H743 MCU support.
- Allwinner sunxi: deep simplifications on how to support
subvariants of SoCs without adding to much SoC-specific data
for each subvariant, especially for sun5i variants. New driver
for V3s SoCs. New driver for the H5 SoC. Support A31/A31s
variants with the new variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction.
New subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the
SoC driver to access regmaps. Add infrastructure for pin-bank
retention control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly
in the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm
driver realtime-safe.
-----BEGIN PGP SIGNATURE-----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=IMY0
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Pin control bulk changes for the v4.11 kernel cycle.
Core changes:
- Switch the generic pin config argument from 16 to 24 bits, only use
8 bits for the configuration type. We might need to encode more
information about a certain setting than we need to encode
different generic settings.
- Add a cross-talk API to the pin control GPIO back-end, utilizing
pinctrl_gpio_set_config() from GPIO drivers that want to set up a
certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the GPIO chips,
so that they pass a generic configuration for things like
debouncing and single ended (typically open drain). This change has
also been merged in an immutable branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing a pin
controller before trying to get any hogs.
- For pin controllers putting all group and function definitions into
the device tree, we now have generic code to deal with this and it
is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down. New
subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in the
LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on GPIOs.
Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode. STM32H743 MCU
support.
- Allwinner sunxi: deep simplifications on how to support subvariants
of SoCs without adding to much SoC-specific data for each
subvariant, especially for sun5i variants. New driver for V3s SoCs.
New driver for the H5 SoC. Support A31/A31s variants with the new
variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction. New
subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the SoC
driver to access regmaps. Add infrastructure for pin-bank retention
control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly in
the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm driver
realtime-safe"
* tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (111 commits)
pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()
pinctrl: intel: unlock on error in intel_config_set_pull()
pinctrl: berlin: make bool drivers explicitly non-modular
pinctrl: spear: make bool drivers explicitly non-modular
pinctrl: mvebu: make bool drivers explicitly non-modular
pinctrl: sunxi: make sun5i explicitly non-modular
pinctrl: sunxi: Remove stray printk call in sun5i driver's probe function
pinctrl: samsung: mark PM functions as __maybe_unused
pinctrl: sunxi: Remove redundant A31s pinctrl driver
pinctrl: sunxi: Support A31/A31s with pinctrl variants
pinctrl: Amend bindings for STM32 pinctrl
pinctrl: Add STM32 pinctrl driver DT bindings
pinctrl: stm32: Add STM32H743 MCU support
include: dt-bindings: Add STM32H7 pinctrl DT defines
gpio: aspeed: Remove dependence on GPIOF_* macros
pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
drivers: pinctrl: add driver for Allwinner H5 SoC
pinctrl: intel: Add Intel Gemini Lake pin controller support
pinctrl: intel: Add support for 1k additional pull-down
pinctrl: intel: Add support for hardware debouncer
...
We had all these corrected in commit 0c8c6ba00c ("pinctrl: sunxi:
make bool drivers explicitly non-modular") but this new one recently
crept in.
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/sunxi/Kconfig:config PINCTRL_SUN5I
drivers/pinctrl/sunxi/Kconfig: def_bool MACH_SUN5I
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a stray printk call in the new sun5i pinctrl driver's probe
function.
Remove it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we can support the A31s pin controller with the A31 driver
using the new variants support, the independent A31s driver becomes
redundant.
Remove it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31s is a trimmed down version of the A31. Some hardware blocks
are removed, thus not available for muxing on the external pins.
Some external pins were directly removed.
This makes it easy to support the A31s pin controller with the A31
driver. We just mark the pins and functions that were trimmed as
A31 only.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on the Allwinner H5 datasheet and the pinctrl driver of the
backward-compatible H3 this introduces the pin multiplex assignments for
the H5 SoC.
H5 introduced some more pin functions (e.g. three more groups of TS
pins, and one more groups of SIM pins) than H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 07fe64ba21 ("pinctrl: sunxi: Handle bias disable") actually
enforced enforced the disabling of the pull up/down resistors instead of
ignoring it like it was done before.
This was part of a wider rework to switch to the generic pinconf bindings,
and was meant to be merged together with DT patches that were switching to
it, and removing what was considered default values by both the binding and
the boards. This included no bias on a pin.
However, those DT patches were delayed to 4.11, which would be fine only
for a significant number boards having the bias setup wrong, which in turns
break the MMC on those boards (and possibly other devices too).
In order to avoid conflicts as much as possible, bring back the old
behaviour for 4.10, and we'll revert that commit once all the DT bits will
have landed.
Tested-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current pinconf packed format allows only 16-bit argument limiting
the maximum value 65535. For most types this is enough. However,
debounce time can be in range of hundreths of milliseconds in case of
mechanical switches so we cannot represent the worst case using the
current format.
In order to support larger values change the packed format so that the
lower 8 bits are used as type which leaves 24 bits for the argument.
This allows representing values up to 16777215 and debounce times up to
16 seconds.
We also convert the existing users to use 32-bit integer when extracting
argument from the packed configuration value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
V3s SoC features only a pin controller (for the lack of CPUs part).
Add a driver for this controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have a common pinctrl driver for all the sun5i SoCs, we can
remove the old, separate drivers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sun5i SoCs (A10s, A13, GR8) are all based on the same die fit in
different packages. Hence, the pins and functions available are just the
based on the same set, each SoC having a different subset.
Introduce a common pinctrl driver that supports multiple variants to allow
to put as much as we can in common.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs are either supposed to be pin compatible (A10 and A20 for
example), or are just repackaged versions of the same die (A10s, A13, GR8).
In those case, having a full blown pinctrl driver just introduces
duplication in both data size and maintainance effort.
Add a variant option to both pins and functions to be able to limit the
pins and functions described only to a subset of the SoC we support with a
given driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Smatch complains that we dereference "map" before testing it for NULL
which is true. We should be testing "*map" instead. Also on the error
path, we should free *map and set it to NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gcc warns about a way that it could use an uninitialized variable:
drivers/pinctrl/sunxi/pinctrl-sunxi.c: In function 'sunxi_pinctrl_init':
drivers/pinctrl/sunxi/pinctrl-sunxi.c:1191:8: error: 'best_div' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This cannot really happen except if 'freq' is UINT_MAX and 'clock' is
zero, and both of these are forbidden. To shut up the warning anyway,
this changes the logic to initialize the return code to the first
divider value before looking at the others.
Fixes: 7c926492d3 ("pinctrl: sunxi: Add support for interrupt debouncing")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin controller found in the Allwinner SoCs has support for interrupts
debouncing.
However, this is not done per-pin, preventing us from using the generic
pinconf binding for that, but per irq bank, which, depending on the SoC,
ranges from one to five.
Introduce a device-wide property to deal with this using a microsecond
resolution. We can re-use the per-pin input-debounce property for that, so
let's do it!
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi_pconf_reg helper introduced in the last patch gives us the
chance to rework sunxi_pconf_group_set to have it match the structure
of sunxi_pconf_(group_)get and make it easier to understand.
For each config to set, it:
1. checks if the parameter is supported.
2. checks if the argument is within limits.
3. converts argument to the register value.
4. writes to the register with spinlock held.
As a result the function now blocks unsupported config parameters,
instead of silently ignoring them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi pinctrl driver only caches whatever pinconf setting was last
set on a given pingroup. This is not particularly helpful, nor is it
correct.
Fix this by actually reading the hardware registers and returning
the correct results or error codes. Also filter out unsupported
pinconf settings. Since this driver has a peculiar setup of 1 pin
per group, we can support both pin and pingroup pinconf setting
read back with the same code. The sunxi_pconf_reg helper and code
structure is inspired by pinctrl-msm.
With this done we can also claim to support generic pinconf, by
setting .is_generic = true in pinconf_ops.
Also remove the cached config value. The behavior of this was never
correct, as it only cached 1 setting instead of all of them. Since
we can now read back settings directly from the hardware, it is no
longer required.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to pinconf-generic.h, the argument for
PIN_CONFIG_BIAS_PULL_{DOWN,UP} is non-zero if the bias is enabled
with a pull up/down resistor, zero if it is directly connected
to VDD or ground.
Since Allwinner hardware uses a weak pull resistor internally,
the argument should be 1.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the recently refactored sunxi pinctrl library, we are only allocating
one set of pin configs for each pinmux setting node. When the pinctrl_map
structure is freed, the pin configs should also be freed. However the
code assumed the first map would contain the configs, which actually
never happens, as the mux function map gets added first.
The proper way to do this is to look through all the maps and free the
first one whose type is actually PIN_MAP_TYPE_CONFIGS_GROUP.
Also slightly expand the comment explaining this.
Fixes: f233dbca62 ("pinctrl: sunxi: Rework the pin config building code")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get essentially the same change, so they are handled in batch.
Changes are (1) use builtin_platform_driver, (2) use init.h header
(3) delete module_exit related code, (4) delete MODULE_DEVICE_TABLE,
and (5) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We do delete the MODULE_LICENSE etc. tags since all that information
is already contained at the top of each file in the comments.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Vishnu Patekar <vishnupatekar0510@gmail.com>
Cc: Mylene Josserand <mylene.josserand@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Even though the our binding had the assumption that the allwinner,pull and
allwinner,drive properties were optional, the code never took that into
account.
Fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Our bindings are mostly irrelevant now that we have generic pinctrl
bindings that cover exactly the same uses cases.
Add support for the new ones, and obviously keep our old binding support in
order to keep the ABI stable.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
So far, putting NO_PULL in allwinner,pull was ignored, behaving like if
that property was not there at all.
Obviously, this is not the right thing to do, and in that case, we really
need to just disable the bias.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we have some bindings header for our hardcoded flags, let's use them
when we can.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to support more easily the generic pinctrl properties, rework the
pinctrl maps configuration and split it into several sub-functions.
One of the side-effects from that rework is that we only parse the pin
configuration once, since it's going to be common to every pin, instead of
having to parsing once for each pin.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
The generic GPIO library directly implement code for acpi_find_gpio()
which is only used with CONFIG_ACPI. This was probably done because
OF did the same thing, but I removed that so remove this too.
Rename the internal acpi_find_gpio() in gpiolib-acpi.c to
acpi_populate_gpio_lookup() which seems to be more appropriate anyway
so as to avoid a namespace clash with the same function.
Make the stub return -ENOENT rather than -ENOSYS (as that is for
syscalls!).
For some reason the sunxi pin control driver was including the private
gpiolib header, it works just fine without it so remove that oneliner.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
H3 has single PWM channel. The second PWM channel is not supported,
so the pinctrl function should be removed.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just like the other member of the sunxi family, let's add a pinctrl table
for the muxing options.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PG8, PG9 is said to be the CTS/RTS pins for UART1 according to the A23/33
datasheets. However, the function is wrongly named "uart2" in the pinctrl
driver. This patch fixes this by modifying them to be named "uart1".
Cc: stable@vger.kernel.org
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the SPDIF mux functionality to the pinctrl for the Allwinner A31
SoC.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In sun4/5/6/7i, all the pin function related to NAND0 controller is
named "nand0". However, in sun8i, some of the functions are named as
"nand". This patch renamed them to "nand0", for the consistency.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable drivers
to use it, saving lots of lines of code all over the place.
New drivers:
- New driver for the Broadcom NS2 SoC.
- New subdriver for the PXA25x SoCs.
- New subdriver for the AMLogic Meson GXBB SoC.
Driver improvements:
- The Intel Baytrail driver now properly supports pin control.
- The Nomadik, Rockchip, Broadcom BCM2835 supports the .get_direction() callback in
the GPIO portions.
- Continued development and stabilization of several SH-PFC
SoC subdrivers: r8a7795, r8a7790, r8a7794 etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tlvn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This kernel cycle was quite calm when it comes to pin control and
there is really just one major change, and that is the introduction of
devm_pinctrl_register() managed resources.
Apart from that linear development, details below.
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable
drivers to use it, saving lots of lines of code all over the place.
New drivers:
- driver for the Broadcom NS2 SoC
- subdriver for the PXA25x SoCs
- subdriver for the AMLogic Meson GXBB SoC
Driver improvements:
- the Intel Baytrail driver now properly supports pin control
- Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
callback in the GPIO portions
- continued development and stabilization of several SH-PFC SoC
subdrivers: r8a7795, r8a7790, r8a7794 etc"
* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
pinctrl: meson: Fix eth_tx_en bit index
pinctrl: tegra: avoid parked_reg and parked_bank
pinctrl: tegra: Correctly check the supported configuration
pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
pinctrl: rockchip: fix pull setting error for rk3399
pinctrl: stm32: Implement .pin_config_dbg_show()
pinctrl: nomadik: hide nmk_gpio_get_mode when unused
pinctrl: ns2: rename pinctrl_utils_dt_free_map
pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
pinctrl: at91: Make at91_gpio_template const
pinctrl: baytrail: fix some error handling in debugfs
pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
pinctrl: nomadik: implement .get_direction()
pinctrl: nomadik: use BIT() with offsets consequently
pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
...
Use devm_pinctrl_register() for pin control registration and clean
the error path.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl-sun8i-a33.c (and the dts) declare only 2 interrupt banks,
where as the closely related a23 has 3 banks. This matches with the
datasheet for the A33 where only interrupt banks B and G are specified
where as the A23 has banks A, B and G.
However the A33 being the A23 derative it is means that the interrupt
configure/status io-addresses for the 2 banks it has are not changed
from the A23, iow they have the same address as if bank A was still
present. Where as the sunxi pinctrl currently tries to use the A23 bank
A addresses for bank B, since the pinctrl code does not know about the
removed bank A.
Add a irq_bank_base parameter and use this where appropriate to take
the missing bank A into account.
This fixes external interrupts not working on the A33 (tested with
an i2c touchscreen controller which uses an external interrupt).
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
Based on the Allwinner A64 user manual and on the previous sunxi
pinctrl drivers this introduces the pin multiplex assignments for
the ARMv8 Allwinner A64 SoC.
Port A is apparently used for the fixed function DRAM controller, so
the ports start at B here (the manual mentions "n from 1 to 7", so
not starting at 0).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/sunxi/Kconfig:config PINCTRL_SUN9I_A80_R
drivers/pinctrl/sunxi/Kconfig: def_bool MACH_SUN9I
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This file is not modular, nor is it using modular functions. The
only thing close is the global THIS_MODULE which comes from export.h
so lets replace it appropriately and cut back on the amount of
header stuff we draw in by several thousand lines.
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While I was testing irq's on the cubietruck I found a couple of
not working irq pins. Further diving into the problem it opened
up a mess called "manual".
This so called manual (A20 user manual v1.3 dated 2014-10-10) says:
Pin overview:
Page 237: EINT26 is on mux 5.
Page 288: EINT26 is on mux 6.
The manual is so contradicting that further tests had to be made
to see which of the 2 statements where correct.
This patch is based on actual outcome of these tests and not what
the manual says.
Test procedure used:
Connect a 1 pulse per second (GPS) line to the pin.
echo pin### > /sys/class/gpio/export
echo in > /sys/class/gpio/gpio###/direction
echo rising > /sys/class/gpio/gpio###/edge
Check /proc/interrupts if a irq was attached and if irq's where
received.
Hardware used:
Henry Paulissen: Cubietruck
Andere Przywara: BananaPi M1
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Henry Paulissen <henry@nitronetworks.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While I was testing irq's on the cubietruck I found a couple of
not working irq pins. Further diving into the problem it opened
up a mess called "manual".
This so called manual (A20 user manual v1.3 dated 2014-10-10) says:
Pin overview:
Page 233: EINT12 is on pin PC19 mux6.
Page 236: EINT12 is on pin PH12 mux6.
Now, it is a bit strange to have the same IRQ on 2 different pins,
but I guess this could still be possible hardware wise. But then:
Pin registers:
Page 253: EINT12 is *not* on pin PC19.
Page 281: EINT12 is on pin PH12.
The manual is so contradicting that further tests had to be made
to see which of the 2 statements where correct.
This patch is based on actual outcome of these tests and not what
the manual says.
Test procedure used:
Connect a 1 pulse per second (GPS) line to the pin.
echo pin### > /sys/class/gpio/export
echo in > /sys/class/gpio/gpio###/direction
echo rising > /sys/class/gpio/gpio###/edge
Check /proc/interrupts if a irq was attached and if irq's where
received.
Signed-off-by: Henry Paulissen <henry@nitronetworks.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This kind of hacks disturbs the refactoring of the gpiolib.
The descriptor table belongs to the gpiolib, if we want to know
something about something in it, use or define the proper accessor
functions. Let's add this gpiochip_lins_is_irq() to do what the
sunxi driver is trying at so we can privatize the descriptors
properly.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Chen-Yu Tsai