This patch (as1350) removes all usages of coherent buffers for USB
control-request setup-packet buffers. There's no good reason to
reserve coherent memory for these things; control requests are hardly
ever used in large quantity (the major exception is firmware
transfers, and they aren't time-critical). Furthermore, only seven
drivers used it. We might as well always use streaming DMA mappings
for setup-packet buffers, and remove some extra complexity from
usbcore.
The DMA-mapping portion of hcd.c is currently in flux. A separate
patch will be submitted to remove support for URB_NO_SETUP_DMA_MAP
after everything else settles down. The removal should go smoothly,
as by then nobody will be using it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices do not react to a control request (seen on APC UPS's) resulting in
a slow stream of messages, "generic-usb ... control queue full". Therefore
request needs a timeout.
Cc: stable@kernel.org
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This uses the USB busy mechanism for aggessive autosuspend of USB
HID devices. It autosuspends all opened devices supporting remote wakeup
after a timeout unless
- output is being done to the device
- a key is being held down (remote wakeup isn't triggered upon key release)
- LED(s) are lit
- hiddev is opened
As in the current driver closed devices will be autosuspended even if they
don't support remote wakeup.
The patch is quite large because output to devices is done in hard interrupt
context meaning a lot a queuing and locking had to be touched. The LED stuff
has been solved by means of a simple counter. Additions to the generic HID code
could be avoided. In addition it now covers hidraw. It contains an embryonic
version of an API to let the generic HID code tell the lower levels which
capabilities with respect to power management are needed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move usbhid specific flags from global hid.h into local usbhid.h.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It causes recursive locking warning and is unneeded after
introduction of STARTED flag.
* Resume vs. stop is effectively solved by DISCONNECT flag.
* No problem in suspend vs. start -- urb is submitted even after open
which is possible after connect which is called after start.
* Resume vs. start solved by STARTED flag.
* Suspend vs. stop -- no problem in killing urb and timer twice.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Usbhid structure is allocated on start invoked only from probe
of some driver. When there is no driver, the structure is null
and causes null-dereference oopses.
Fix it by allocating the structure on probe and disconnect of
the device itself. Also make sure we won't race between start
and resume or stop and suspend respectively.
References: http://bugzilla.kernel.org/show_bug.cgi?id=11827
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Andreas Schwab <schwab@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 8006479c9b introduced a spinlock in
input_dev->event_lock, which is locked when handling input events.
However, the hid-pidff driver sleeps when handling events as it waits for
reports being sent to the device before changing the report contents
again.
This causes a system lockup when trying to use force feedback with a PID
device, a regression introduced in 2.6.24 and 2.6.23.15.
Fix it by extracting the raw report data from struct hid_report
immediately when hid_submit_report() is called, therefore allowing
drivers to change the contents of struct hid_report immediately without
affecting the already-queued transfer.
In hid-pidff, re-add the removed usbhid_wait_io() to
pidff_erase_effect() instead, to prevent a full report queue from causing
the submission to fail, thus not freeing up device memory.
pidff_erase_effect() is not called while dev->event_lock is held.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make a bus from hid core. This is the first step for converting all the
quirks and separate almost-drivers into real drivers attached to this bus.
It's implemented to change behaviour in very tiny manner, so that no driver
needs to be changed this time.
Also add generic drivers for both usb and bt into usbhid or hidp
respectively which will bind all non-blacklisted device. Those blacklisted
will be either grabbed by special drivers or by nobody if they are broken at
the very rude base.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Separate usbhid code into dedicated drivers/hid/usbhid directory as
discussed previously with Greg, so that it eases maintaineance process.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern