ip6_tunnels use one rwlock to protect their hash tables.
This locking scheme can be converted to RCU for free, since netdevice
already must wait for a RCU grace period at dismantle time.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm6_tunnels use one rwlock to protect their hash tables.
Plain and straightforward conversion to RCU locking to permit better SMP
performance.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIT tunnels use one rwlock to protect their hash tables.
This locking scheme can be converted to RCU for free, since netdevice
already must wait for a RCU grace period at dismantle time.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIT tunnels use one rwlock to protect their prl entries.
This first patch adds RCU locking for prl management,
with standard call_rcu() calls.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6: Reset sk_tx_queue_mapping when dst_cache is reset. Use existing
macro to do the work.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use symbols instead of magic constants while checking PMTU discovery
setsockopt.
Remove redundant test in ip_rt_frag_needed() (done by caller).
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4/ipv6 setsockopt(IP_MULTICAST_IF) have dubious __dev_get_by_index() calls.
This function should be called only with RTNL or dev_base_lock held, or reader
could see a corrupt hash chain and eventually enter an endless loop.
Fix is to call dev_get_by_index()/dev_put().
If this happens to be performance critical, we could define a new dev_exist_by_index()
function to avoid touching dev refcount.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts ah6 to the new ahash interface.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- skb_kill_datagram() can increment sk->sk_drops itself, not callers.
- UDP on IPV4 & IPV6 dropped frames (because of bad checksum or policy checks) increment sk_drops
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have better cache layouts of struct sock (separate zones
for rx/tx paths), we need this preliminary patch.
Goal is to transfert fields used at lookup time in the first
read-mostly cache line (inside struct sock_common) and move sk_refcnt
to a separate cache line (only written by rx path)
This patch adds inet_ prefix to daddr, rcv_saddr, dport, num, saddr,
sport and id fields. This allows a future patch to define these
fields as macros, like sk_refcnt, without name clashes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_queue_rcv_skb() can update sk_drops itself, removing need for
callers to take care of it. This is more consistent since
sock_queue_rcv_skb() also reads sk_drops when queueing a skb.
This adds sk_drops managment to many protocols that not cared yet.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storing the mask (size - 1) instead of the size allows fast path to be
a bit faster.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new socket level option to report number of queue overflows
Recently I augmented the AF_PACKET protocol to report the number of frames lost
on the socket receive queue between any two enqueued frames. This value was
exported via a SOL_PACKET level cmsg. AFter I completed that work it was
requested that this feature be generalized so that any datagram oriented socket
could make use of this option. As such I've created this patch, It creates a
new SOL_SOCKET level option called SO_RXQ_OVFL, which when enabled exports a
SOL_SOCKET level cmsg that reports the nubmer of times the sk_receive_queue
overflowed between any two given frames. It also augments the AF_PACKET
protocol to take advantage of this new feature (as it previously did not touch
sk->sk_drops, which this patch uses to record the overflow count). Tested
successfully by me.
Notes:
1) Unlike my previous patch, this patch simply records the sk_drops value, which
is not a number of drops between packets, but rather a total number of drops.
Deltas must be computed in user space.
2) While this patch currently works with datagram oriented protocols, it will
also be accepted by non-datagram oriented protocols. I'm not sure if thats
agreeable to everyone, but my argument in favor of doing so is that, for those
protocols which aren't applicable to this option, sk_drops will always be zero,
and reporting no drops on a receive queue that isn't used for those
non-participating protocols seems reasonable to me. This also saves us having
to code in a per-protocol opt in mechanism.
3) This applies cleanly to net-next assuming that commit
977750076d (my af packet cmsg patch) is reverted
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6 sit: Set relay to 0.0.0.0 directly if relay_prefixlen == 0.
Do not use bit-shift if relay_prefixlen == 0;
relay_prefix << 32 does not result in 0.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6 sit: Fix 6rd relay address.
Relay's address should be extracted from real IPv6 address
instead of configured prefix.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6 sit: Ensure to initialize 6rd parameters.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP_HTABLE_SIZE was initialy defined to 128, which is a bit small for
several setups.
4000 active UDP sockets -> 32 sockets per chain in average. An
incoming frame has to lookup all sockets to find best match, so long
chains hurt latency.
Instead of a fixed size hash table that cant be perfect for every
needs, let UDP stack choose its table size at boot time like tcp/ip
route, using alloc_large_system_hash() helper
Add an optional boot parameter, uhash_entries=x so that an admin can
force a size between 256 and 65536 if needed, like thash_entries and
rhash_entries.
dmesg logs two new lines :
[ 0.647039] UDP hash table entries: 512 (order: 0, 4096 bytes)
[ 0.647099] UDP Lite hash table entries: 512 (order: 0, 4096 bytes)
Maximal size on 64bit arches would be 65536 slots, ie 1 MBytes for non
debugging spinlocks.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Might as well use the ipv6_addr_set_v4mapped() inline we created last
year.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ip6_route_redirect() to use ipv6_addr_copy().
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All usages of structure net_proto_ops should be declared const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Friday 02 October 2009 20:53:51 you wrote:
> This is good although I would have shortened the name.
Ah, I knew I forgot something :) Here is v4.
tavi
>From 24d96d825b9fa832b22878cc6c990d5711968734 Mon Sep 17 00:00:00 2001
From: Octavian Purdila <opurdila@ixiacom.com>
Date: Fri, 2 Oct 2009 00:51:15 +0300
Subject: [PATCH] ipv6: new sysctl for sending TLLAO with unicast NAs
Neighbor advertisements responding to unicast neighbor solicitations
did not include the target link-layer address option. This patch adds
a new sysctl option (disabled by default) which controls whether this
option should be sent even with unicast NAs.
The need for this arose because certain routers expect the TLLAO in
some situations even as a response to unicast NS packets.
Moreover, RFC 2461 recommends sending this to avoid a race condition
(section 4.4, Target link-layer address)
Signed-off-by: Cosmin Ratiu <cratiu@ixiacom.com>
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Atis Elsts wrote:
> Not sure if there is need to fill the mark from skb in tunnel xmit functions. In any case, it's not done for GRE or IPIP tunnels at the moment.
Ok, I'll just drop that part, I'm not sure what should be done in this case.
> Also, in this patch you are doing that for SIT (v6-in-v4) tunnels only, and not doing it for v4-in-v6 or v6-in-v6 tunnels. Any reason for that?
I just sent that patch out too quickly, here's a better one with the updates.
Add support for IPv6 route lookups using sk_mark.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 Rapid Deployment (6rd; draft-ietf-softwire-ipv6-6rd) builds upon
mechanisms of 6to4 (RFC3056) to enable a service provider to rapidly
deploy IPv6 unicast service to IPv4 sites to which it provides
customer premise equipment. Like 6to4, it utilizes stateless IPv6 in
IPv4 encapsulation in order to transit IPv4-only network
infrastructure. Unlike 6to4, a 6rd service provider uses an IPv6
prefix of its own in place of the fixed 6to4 prefix.
With this option enabled, the SIT driver offers 6rd functionality by
providing additional ioctl API to configure the IPv6 Prefix for in
stead of static 2002::/16 for 6to4.
Original patch was done by Alexandre Cassen <acassen@freebox.fr>
based on old Internet-Draft.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently dirty a cache line to update tunnel device stats
(tx_packets/tx_bytes). We better use the txq->tx_bytes/tx_packets
counters that already are present in cpu cache, in the cache
line shared with txq->_xmit_lock
This patch extends IPTUNNEL_XMIT() macro to use txq pointer
provided by the caller.
Also &tunnel->dev->stats can be replaced by &dev->stats
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When requesting all prl entries (kprl.addr == INADDR_ANY) and there are
more prl entries than there is space passed from userspace, the existing
code would always copy cmax+1 entries, which is more than can be handled.
This patch makes the kernel copy only exactly cmax entries.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Acked-By: Fred L. Templin <Fred.L.Templin@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides safety against negative optlen at the type
level instead of depending upon (sometimes non-trivial)
checks against this sprinkled all over the the place, in
each and every implementation.
Based upon work done by Arjan van de Ven and feedback
from Linus Torvalds.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 645069299a.
While the code does not actually break anything, it does not completely follow
RFC5214 yet. After talking back with Fred L. Templin, I agree that completing the
ISATAP specific RS/RA code, would pollute the kernel a lot with code that is better
implemented in userspace.
The kernel should not send RS packages for ISATAP at all.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Acked-by: Fred L. Templin <Fred.L.Templin@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems recursion field from "struct ip_tunnel" is not anymore needed.
recursion prevention is done at the upper level (in dev_queue_xmit()),
since we use HARD_TX_LOCK protection for tunnels.
This avoids a cache line ping pong on "struct ip_tunnel" : This structure
should be now mostly read on xmit and receive paths.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unused.
It isn't needed -- read or write flag is already passed and sysctl
shouldn't care about the rest.
It _was_ used in two places at arch/frv for some reason.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make all seq_operations structs const, to help mitigate against
revectoring user-triggerable function pointers.
This is derived from the grsecurity patch, although generated from scratch
because it's simpler than extracting the changes from there.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
be2net: fix some cmds to use mccq instead of mbox
atl1e: fix 2.6.31-git4 -- ATL1E 0000:03:00.0: DMA-API: device driver frees DMA
pkt_sched: Fix qstats.qlen updating in dump_stats
ipv6: Log the affected address when DAD failure occurs
wl12xx: Fix print_mac() conversion.
af_iucv: fix race when queueing skbs on the backlog queue
af_iucv: do not call iucv_sock_kill() twice
af_iucv: handle non-accepted sockets after resuming from suspend
af_iucv: fix race in __iucv_sock_wait()
iucv: use correct output register in iucv_query_maxconn()
iucv: fix iucv_buffer_cpumask check when calling IUCV functions
iucv: suspend/resume error msg for left over pathes
wl12xx: switch to %pM to print the mac address
b44: the poll handler b44_poll must not enable IRQ unconditionally
ipv6: Ignore route option with ROUTER_PREF_INVALID
bonding: make ab_arp select active slaves as other modes
cfg80211: fix SME connect
rc80211_minstrel: fix contention window calculation
ssb/sdio: fix printk format warnings
p54usb: add Zcomax XG-705A usbid
...
If an interface has multiple addresses, the current message for DAD
failure isn't really helpful, so this patch adds the address itself to
the printk.
Signed-off-by: Jens Rosenboom <me@jayr.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4191 says that "If the Reserved (10) value is received, the Route
Information Option MUST be ignored.", so this patch makes us conform
to the RFC. This is different to the usage of the Default Router
Preference, where an invalid value must indeed be treated as
PREF_MEDIUM.
Signed-off-by: Jens Rosenboom <me@jayr.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (46 commits)
powerpc64: convert to dynamic percpu allocator
sparc64: use embedding percpu first chunk allocator
percpu: kill lpage first chunk allocator
x86,percpu: use embedding for 64bit NUMA and page for 32bit NUMA
percpu: update embedding first chunk allocator to handle sparse units
percpu: use group information to allocate vmap areas sparsely
vmalloc: implement pcpu_get_vm_areas()
vmalloc: separate out insert_vmalloc_vm()
percpu: add chunk->base_addr
percpu: add pcpu_unit_offsets[]
percpu: introduce pcpu_alloc_info and pcpu_group_info
percpu: move pcpu_lpage_build_unit_map() and pcpul_lpage_dump_cfg() upward
percpu: add @align to pcpu_fc_alloc_fn_t
percpu: make @dyn_size mandatory for pcpu_setup_first_chunk()
percpu: drop @static_size from first chunk allocators
percpu: generalize first chunk allocator selection
percpu: build first chunk allocators selectively
percpu: rename 4k first chunk allocator to page
percpu: improve boot messages
percpu: fix pcpu_reclaim() locking
...
Fix trivial conflict as by Tejun Heo in kernel/sched.c
This patch fixes commit e36b9d16c6. The approach
there is to call dev_close()/dev_open() whenever the device type is changed in
order to remap the device IP multicast addresses to HW multicast addresses.
This approach suffers from 2 drawbacks:
*. It assumes tha the device is UP when calling dev_close(), or otherwise
dev_close() has no affect. It is worth to mention that initscripts (Redhat)
and sysconfig (Suse) doesn't act the same in this matter.
*. dev_close() has other side affects, like deleting entries from the routing
table, which might be unnecessary.
The fix here is to directly remap the IP multicast addresses to HW multicast
addresses for a bonding device that changes its type, and nothing else.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was once upon time so that snd_sthresh was a 16-bit quantity.
...That has not been true for long period of time. I run across
some ancient compares which still seem to trust such legacy.
Put all that magic into a single place, I hopefully found all
of them.
Compile tested, though linking of allyesconfig is ridiculous
nowadays it seems.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFA_F_DADFAILED flag to denote an IPv6 address that has
failed Duplicate Address Detection, that way tools like
/sbin/ip can be more informative.
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:db8::1/64 scope global tentative dadfailed
valid_lft forever preferred_lft forever
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a patch which fixes an issue observed when using TCP over IPv6
and AH from IPsec.
When a connection gets closed the 4-way method and the last ACK from
the server gets dropped, the subsequent FINs from the client do not
get ACKed because tcp_v6_send_response does not set the transport
header pointer. This causes ah6_output to try to allocate a lot of
memory, which typically fails, so the ACKs never make it out of the
stack.
I have reproduced the problem on kernel 2.6.7, but after looking at
the latest kernel it seems the problem is still there.
Signed-off-by: Cosmin Ratiu <cratiu@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixed a lockdep warning which appeared when doing stress
memory tests over NFS:
inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
page reclaim => nfs_writepage => tcp_sendmsg => lock sk_lock
mount_root => nfs_root_data => tcp_close => lock sk_lock =>
tcp_send_fin => alloc_skb_fclone => page reclaim
David raised a concern that if the allocation fails in tcp_send_fin(), and it's
GFP_ATOMIC, we are going to yield() (which sleeps) and loop endlessly waiting
for the allocation to succeed.
But fact is, the original GFP_KERNEL also sleeps. GFP_ATOMIC+yield() looks
weird, but it is no worse the implicit sleep inside GFP_KERNEL. Both could
loop endlessly under memory pressure.
CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
CC: David S. Miller <davem@davemloft.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Lameter pointed out that packet drops at qdisc level where not
accounted in SNMP counters. Only if application sets IP_RECVERR, drops
are reported to user (-ENOBUFS errors) and SNMP counters updated.
IP_RECVERR is used to enable extended reliable error message passing,
but these are not needed to update system wide SNMP stats.
This patch changes things a bit to allow SNMP counters to be updated,
regardless of IP_RECVERR being set or not on the socket.
Example after an UDP tx flood
# netstat -s
...
IP:
1487048 outgoing packets dropped
...
Udp:
...
SndbufErrors: 1487048
send() syscalls, do however still return an OK status, to not
break applications.
Note : send() manual page explicitly says for -ENOBUFS error :
"The output queue for a network interface was full.
This generally indicates that the interface has stopped sending,
but may be caused by transient congestion.
(Normally, this does not occur in Linux. Packets are just silently
dropped when a device queue overflows.) "
This is not true for IP_RECVERR enabled sockets : a send() syscall
that hit a qdisc drop returns an ENOBUFS error.
Many thanks to Christoph, David, and last but not least, Alexey !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All instances of file_operations should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function block inet_connect_sock_af_ops contains no data
make it constant.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc drops should be notified to IP_RECVERR enabled sockets, as done in IPV4.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These tables are never modified at runtime. Move to read-only
section.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct net::ipv6.ip6_dst_ops is separatedly dynamically allocated,
but there is no fundamental reason for it. Embed it directly into
struct netns_ipv6.
For that:
* move struct dst_ops into separate header to fix circular dependencies
I honestly tried not to, it's pretty impossible to do other way
* drop dynamical allocation, allocate together with netns
For a change, remove struct dst_ops::dst_net, it's deducible
by using container_of() given dst_ops pointer.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use memcmp() instead of open coded comparison that reads one byte past
the intended end.
Based on patch from Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
When processing a received IPv6 Router Advertisement, the kernel
creates or updates an IPv6 Neighbor Cache entry for the sender --
but presently this does not occur if IPv6 forwarding is enabled
(net.ipv6.conf.*.forwarding = 1), or if IPv6 Router Advertisements
are not accepted (net.ipv6.conf.*.accept_ra = 0), because in these
cases processing of the Router Advertisement has already halted.
This patch allows the Neighbor Cache to be updated in these cases,
while still avoiding any modification to routes or link parameters.
This continues to satisfy RFC 4861, since any entry created in the
Neighbor Cache as the result of a received Router Advertisement is
still placed in the STALE state.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
if tunnel parameters have frag_off set to IP_DF, pmtudisc on the ipv4 link
will be performed by deriving the mtu from the ipv4 link and setting the
DF-Flag of the encapsulating IPv4 Header. If fragmentation is needed on the
way, the IPv4 pmtu gets adjusted, the ipv6 package will be resent eventually,
using the new and lower mtu and everyone is happy.
If the frag_off parameter is unset, the mtu for the tunnel will be derived
from the tunnel device or the ipv6 pmtu, which might be higher than the ipv4
pmtu. In that case we must allow the fragmentation of the IPv4 packet because
the IPv6 mtu wouldn't 'learn' from the adjusted IPv4 pmtu, resulting in
frequent icmp_frag_needed and package loss on the IPv6 layer.
This patch allows fragmentation when tunnel was created with parameter
nopmtudisc, like in ipip/gre tunnels.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log packets dropped by helpers using the netfilter logging API. This
is useful in combination with nfnetlink_log to analyze those packets
in userspace for debugging.
Signed-off-by: Patrick McHardy <kaber@trash.net>
The inputted table is never modified, so should be considered const.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Commit 63d9950b08
(ipv6: Make v4-mapped bindings consistent with IPv4)
changes behavior of inet6_bind() for v4-mapped addresses so it should
behave the same way as inet_bind().
During this change setting of err to -EADDRNOTAVAIL got lost:
af_inet.c:469 inet_bind()
err = -EADDRNOTAVAIL;
if (!sysctl_ip_nonlocal_bind &&
!(inet->freebind || inet->transparent) &&
addr->sin_addr.s_addr != htonl(INADDR_ANY) &&
chk_addr_ret != RTN_LOCAL &&
chk_addr_ret != RTN_MULTICAST &&
chk_addr_ret != RTN_BROADCAST)
goto out;
af_inet6.c:463 inet6_bind()
if (addr_type == IPV6_ADDR_MAPPED) {
int chk_addr_ret;
/* Binding to v4-mapped address on a v6-only socket
* makes no sense
*/
if (np->ipv6only) {
err = -EINVAL;
goto out;
}
/* Reproduce AF_INET checks to make the bindings consitant */
v4addr = addr->sin6_addr.s6_addr32[3];
chk_addr_ret = inet_addr_type(net, v4addr);
if (!sysctl_ip_nonlocal_bind &&
!(inet->freebind || inet->transparent) &&
v4addr != htonl(INADDR_ANY) &&
chk_addr_ret != RTN_LOCAL &&
chk_addr_ret != RTN_MULTICAST &&
chk_addr_ret != RTN_BROADCAST)
goto out;
} else {
Signed-off-by Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/sparc/kernel/smp_64.c
arch/x86/kernel/cpu/perf_counter.c
arch/x86/kernel/setup_percpu.c
drivers/cpufreq/cpufreq_ondemand.c
mm/percpu.c
Conflicts in core and arch percpu codes are mostly from commit
ed78e1e078dd44249f88b1dd8c76dafb39567161 which substituted many
num_possible_cpus() with nr_cpu_ids. As for-next branch has moved all
the first chunk allocators into mm/percpu.c, the changes are moved
from arch code to mm/percpu.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch addresses:
* assigning -1 to np->tclass as it is currently done is not very meaningful,
since it turns into 0xff;
* RFC 3542, 6.5 allows -1 for clearing the sticky IPV6_TCLASS option
and specifies -1 to mean "use kernel default":
- RFC 2460, 7. requires that the default traffic class must be zero for
all 8 bits,
- this is consistent with RFC 2474, 4.1 which recommends a default PHB of 0,
in combination with a value of the ECN field of "non-ECT" (RFC 3168, 5.).
This patch changes the meaning of -1 from assigning 255 to mean the RFC 2460
default, which at the same time allows to satisfy clearing the sticky TCLASS
option as per RFC 3542, 6.5.
(When passing -1 as ancillary data, the fallback remains np->tclass, which
has either been set via socket options, or contains the default value.)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces assignments of the type "int on LHS" = "u8 on RHS" with
simpler code. The LHS can express all of the unsigned right hand side
values, hence the assigned value can not be negative.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an interface has multiple addresses, the current message for DAD
failure isn't really helpful, so this patch adds the address itself to
the printk.
Signed-off-by: Jens Rosenboom <jens@mcbone.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the second check that Rusty wanted to have a long time ago. :-)
Base chain policies must have absolute verdicts that cease processing
in the table, otherwise rule execution may continue in an unexpected
spurious fashion (e.g. next chain that follows in memory).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
This adds a check that iptables's original author Rusty set forth in
a FIXME comment.
Underflows in iptables are better known as chain policies, and are
required to be unconditional or there would be a stochastical chance
for the policy rule to be skipped if it does not match. If that were
to happen, rule execution would continue in an unexpected spurious
fashion.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
The "hook_entry" and "underflow" array contains values even for hooks
not provided, such as PREROUTING in conjunction with the "filter"
table. Usually, the values point to whatever the next rule is. For
the upcoming unconditionality and underflow checking patches however,
we must not inspect that arbitrary rule.
Skipping unassigned hooks seems like a good idea, also because
newinfo->hook_entry and newinfo->underflow will then continue to have
the poison value for detecting abnormalities.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Instead of inspecting each u32/char open-coded, clean up and make use
of memcmp. On some arches, memcmp is implemented as assembly or GCC's
__builtin_memcmp which can possibly take advantages of known
alignment.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
String literals are constant, and usually, we can also tag the array
of pointers const too, moving it to the .rodata section.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames away a variable clash:
* ipv6_table[] is declared as a static global table;
* ipv6_sysctl_net_init() uses ipv6_table to refer/destroy dynamic memory;
* ipv6_sysctl_net_exit() also uses ipv6_table for the same purpose;
* both the two last functions call kfree() on ipv6_table.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Choose saner defaults for xfrm[4|6] gc_thresh values on init
Currently, the xfrm[4|6] code has hard-coded initial gc_thresh values
(set to 1024). Given that the ipv4 and ipv6 routing caches are sized
dynamically at boot time, the static selections can be non-sensical.
This patch dynamically selects an appropriate gc threshold based on
the corresponding main routing table size, using the assumption that
we should in the worst case be able to handle as many connections as
the routing table can.
For ipv4, the maximum route cache size is 16 * the number of hash
buckets in the route cache. Given that xfrm4 starts garbage
collection at the gc_thresh and prevents new allocations at 2 *
gc_thresh, we set gc_thresh to half the maximum route cache size.
For ipv6, its a bit trickier. there is no maximum route cache size,
but the ipv6 dst_ops gc_thresh is statically set to 1024. It seems
sane to select a simmilar gc_thresh for the xfrm6 code that is half
the number of hash buckets in the v6 route cache times 16 (like the v4
code does).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export garbage collector thresholds for xfrm[4|6]_dst_ops
Had a problem reported to me recently in which a high volume of ipsec
connections on a system began reporting ENOBUFS for new connections
eventually.
It seemed that after about 2000 connections we started being unable to
create more. A quick look revealed that the xfrm code used a dst_ops
structure that limited the gc_thresh value to 1024, and always
dropped route cache entries after 2x the gc_thresh.
It seems the most direct solution is to export the gc_thresh values in
the xfrm[4|6] dst_ops as sysctls, like the main routing table does, so
that higher volumes of connections can be supported. This patch has
been tested and allows the reporter to increase their ipsec connection
volume successfully.
Reported-by: Joe Nall <joe@nall.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
ipv4/xfrm4_policy.c | 18 ++++++++++++++++++
ipv6/xfrm6_policy.c | 18 ++++++++++++++++++
2 files changed, 36 insertions(+)
Signed-off-by: David S. Miller <davem@davemloft.net>
The local variable 'idev' shadows the function argument 'idev' to
ip6_mc_add_src(). Fixed by removing the local declaration, as pmc->idev
should be identical with 'idev' passed as argument.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the TCP connection handshake completes on the passive
side, a variety of state must be set up in the "child" sock,
including the key if MD5 authentication is being used. Fix TCP
for both address families to label the key with the peer's
destination address, rather than the address from the listening
sock, which is usually the wildcard.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix MD5 signature checking so that an IPv4 active open
to an IPv6 socket can succeed. In particular, use the
correct address family's signature generation function
for the SYN/ACK.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- validate and forward GSO UDP/IPv6 packets from untrusted sources.
- do software UFO if the outgoing device doesn't support UFO.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
- move ipv6_select_ident() inline function to ipv6.h and remove the unused
skb argument
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix gso_size setting for ipv6 fragment to be a multiple of 8 bytes.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add HW checksum support for outgoing large UDP/IPv6 packets destined for
a UFO enabled device.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sit module makes use of skb->dst in it's xmit function, so since
93f154b594 ("net: release dst entry in dev_hard_start_xmit()") sit
tunnels are broken, because the flag IFF_XMIT_DST_RELEASE is not
unset.
This patch unsets that flag for sit devices to fix this
regression.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2b85a34e91
(net: No more expensive sock_hold()/sock_put() on each tx)
we do not take any more references on sk->sk_refcnt on outgoing packets.
I forgot to delete two __sock_put() from ip_push_pending_frames()
and ip6_push_pending_frames().
Reported-by: Emil S Tantilov <emils.tantilov@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Emil S Tantilov <emils.tantilov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The routine ipv6_rcv() uses magic number 0 for a return when it drops a
packet. This corresponds to NET_RX_SUCCESS, which is obviously
incorrect. Correct this by using NET_RX_DROP instead.
ps. It isn't exactly clear who the IPv6 maintainers are, apologies if
I've missed any.
Signed-off-by: Mark Smith <markzzzsmith@yahoo.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a bug in addrconf_prefix_rcv() where it won't update the
preferred lifetime of an IPv6 address if the current valid lifetime
of the address is less than 2 hours (the minimum value in the RA).
For example, If I send a router advertisement with a prefix that
has valid lifetime = preferred lifetime = 2 hours we'll build
this address:
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
valid_lft 7175sec preferred_lft 7175sec
If I then send the same prefix with valid lifetime = preferred
lifetime = 0 it will be ignored since the minimum valid lifetime
is 2 hours:
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
valid_lft 7161sec preferred_lft 7161sec
But according to RFC 4862 we should always reset the preferred lifetime
even if the valid lifetime is invalid, which would cause the address
to immediately get deprecated. So with this patch we'd see this:
5: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:1890:1109:a20:21f:29ff:fe5a:ef04/64 scope global deprecated dynamic
valid_lft 7163sec preferred_lft 0sec
The comment winds-up being 5x the size of the code to fix the problem.
Update the preferred lifetime of IPv6 addresses derived from a prefix
info option in a router advertisement even if the valid lifetime in
the option is invalid, as specified in RFC 4862 Section 5.5.3e. Fixes
an issue where an address will not immediately become deprecated.
Reported by Jens Rosenboom.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP pushed the skb above the sctp chunk header, so the
check of pskb_may_pull(skb, nh + offset + 1 - skb->data) in
_decode_session6() will never return 0 and the ports decode
of sctp will always fail. (nh + offset + 1 - skb->data < 0)
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull linus#master to merge PER_CPU_DEF_ATTRIBUTES and alpha build fix
changes. As alpha in percpu tree uses 'weak' attribute instead of
inline assembly, there's no need for __used attribute.
Conflicts:
arch/alpha/include/asm/percpu.h
arch/mn10300/kernel/vmlinux.lds.S
include/linux/percpu-defs.h
As transparent proxying looks up the socket early and assigns
it to the skb for later processing, we must drop any existing
socket ownership prior to that in order to distinguish between
the case where tproxy is active and where it is not.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 module uses rcu_call() thus it should use rcu_barrier() on
module unload.
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid showing wrong high values when the preferred lifetime of an address
is expired.
Signed-off-by: Jens Rosenboom <me@jayr.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Percpu variable definition is about to be updated such that all percpu
symbols including the static ones must be unique. Update percpu
variable definitions accordingly.
* as,cfq: rename ioc_count uniquely
* cpufreq: rename cpu_dbs_info uniquely
* xen: move nesting_count out of xen_evtchn_do_upcall() and rename it
* mm: move ratelimits out of balance_dirty_pages_ratelimited_nr() and
rename it
* ipv4,6: rename cookie_scratch uniquely
* x86 perf_counter: rename prev_left to pmc_prev_left, irq_entry to
pmc_irq_entry and nmi_entry to pmc_nmi_entry
* perf_counter: rename disable_count to perf_disable_count
* ftrace: rename test_event_disable to ftrace_test_event_disable
* kmemleak: rename test_pointer to kmemleak_test_pointer
* mce: rename next_interval to mce_next_interval
[ Impact: percpu usage cleanups, no duplicate static percpu var names ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: linux-mm <linux-mm@kvack.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Currently, the following three different ways to define percpu arrays
are in use.
1. DEFINE_PER_CPU(elem_type[array_len], array_name);
2. DEFINE_PER_CPU(elem_type, array_name[array_len]);
3. DEFINE_PER_CPU(elem_type, array_name)[array_len];
Unify to #1 which correctly separates the roles of the two parameters
and thus allows more flexibility in the way percpu variables are
defined.
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: linux-mm@kvack.org
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: David S. Miller <davem@davemloft.net>
Change all the code that deals directly with ICMPv6 type and code
values to use u8 instead of a signed int as that's the actual data
type.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2b85a34e91
(net: No more expensive sock_hold()/sock_put() on each tx)
changed initial sk_wmem_alloc value.
We need to take into account this offset when reporting
sk_wmem_alloc to user, in PROC_FS files or various
ioctls (SIOCOUTQ/TIOCOUTQ)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4:
- make PIM register vifs netns local
- set the netns when a PIM register vif is created
- make PIM available in all network namespaces (if CONFIG_IP_PIMSM_V2)
by adding the protocol handler when multicast routing is initialized
IPv6:
- make PIM register vifs netns local
- make PIM available in all network namespaces (if CONFIG_IPV6_PIMSM_V2)
by adding the protocol handler when multicast routing is initialized
Signed-off-by: Tom Goff <thomas.goff@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
One of the problem with sock memory accounting is it uses
a pair of sock_hold()/sock_put() for each transmitted packet.
This slows down bidirectional flows because the receive path
also needs to take a refcount on socket and might use a different
cpu than transmit path or transmit completion path. So these
two atomic operations also trigger cache line bounces.
We can see this in tx or tx/rx workloads (media gateways for example),
where sock_wfree() can be in top five functions in profiles.
We use this sock_hold()/sock_put() so that sock freeing
is delayed until all tx packets are completed.
As we also update sk_wmem_alloc, we could offset sk_wmem_alloc
by one unit at init time, until sk_free() is called.
Once sk_free() is called, we atomic_dec_and_test(sk_wmem_alloc)
to decrement initial offset and atomicaly check if any packets
are in flight.
skb_set_owner_w() doesnt call sock_hold() anymore
sock_wfree() doesnt call sock_put() anymore, but check if sk_wmem_alloc
reached 0 to perform the final freeing.
Drawback is that a skb->truesize error could lead to unfreeable sockets, or
even worse, prematurely calling __sk_free() on a live socket.
Nice speedups on SMP. tbench for example, going from 2691 MB/s to 2711 MB/s
on my 8 cpu dev machine, even if tbench was not really hitting sk_refcnt
contention point. 5 % speedup on a UDP transmit workload (depends
on number of flows), lowering TX completion cpu usage.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current conntrack code kills the ICMP conntrack entry as soon as
the first reply is received. This is incorrect, as we then see only
the first ICMP echo reply out of several possible duplicates as
ESTABLISHED, while the rest will be INVALID. Also this unnecessarily
increases the conntrackd traffic on H-A firewalls.
Make all the ICMP conntrack entries (including the replied ones)
last for the default of nf_conntrack_icmp{,v6}_timeout seconds.
Signed-off-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies the conntrack event caching system by removing
several events:
* IPCT_[*]_VOLATILE, IPCT_HELPINFO and IPCT_NATINFO has been deleted
since the have no clients.
* IPCT_COUNTER_FILLING which is a leftover of the 32-bits counter
days.
* IPCT_REFRESH which is not of any use since we always include the
timeout in the messages.
After this patch, the existing events are:
* IPCT_NEW, IPCT_RELATED and IPCT_DESTROY, that are used to identify
addition and deletion of entries.
* IPCT_STATUS, that notes that the status bits have changes,
eg. IPS_SEEN_REPLY and IPS_ASSURED.
* IPCT_PROTOINFO, that reports that internal protocol information has
changed, eg. the TCP, DCCP and SCTP protocol state.
* IPCT_HELPER, that a helper has been assigned or unassigned to this
entry.
* IPCT_MARK and IPCT_SECMARK, that reports that the mark has changed, this
covers the case when a mark is set to zero.
* IPCT_NATSEQADJ, to report that there's updates in the NAT sequence
adjustment.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Print-out the error value when sock_alloc_send_skb() fails in
the IPv6 neighbor discovery code - can be useful for debugging.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'autoconf' and 'disable_ipv6' parameters to the IPv6 module.
The first controls if IPv6 addresses are autoconfigured from
prefixes received in Router Advertisements. The IPv6 loopback
(::1) and link-local addresses are still configured.
The second controls if IPv6 addresses are desired at all. No
IPv6 addresses will be added to any interfaces.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the overwhelming majority of cases, skb_gro_header's return
value cannot be NULL. Yet we must check it because of its current
form. This patch splits it up into multiple functions in order
to avoid this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sinec the TCPv6 GRO functions are used in the same file where
they are defined, we do not need to export them. This was a
cut-n-paste from the IPv4 code which does need to export them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of unspecified protocol in IPv6 initial route prevents quagga to
install IPv6 default route:
# show ipv6 route
S ::/0 [1/0] via fe80::1, eth1_0
K>* ::/0 is directly connected, lo, rej
C>* ::1/128 is directly connected, lo
C>* fe80::/64 is directly connected, eth1_0
# ip -6 route
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
ff00::/8 dev eth1_0 metric 256 mtu 1500 advmss 1440 hoplimit -1
unreachable default dev lo proto none metric -1 error -101 hoplimit 255
The attached patch ensures RTPROT_KERNEL to the default initial route
and fixes the problem for quagga.
This is similar to "ipv6: protocol for address routes"
f410a1fba7.
# show ipv6 route
S>* ::/0 [1/0] via fe80::1, eth1_0
C>* ::1/128 is directly connected, lo
C>* fe80::/64 is directly connected, eth1_0
# ip -6 route
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
ff00::/8 dev eth1_0 metric 256 mtu 1500 advmss 1440 hoplimit -1
default via fe80::1 dev eth1_0 proto zebra metric 1024 mtu 1500
advmss 1440 hoplimit -1
unreachable default dev lo proto kernel metric -1 error -101 hoplimit 255
Signed-off-by: Jean-Mickael Guerin <jean-mickael.guerin@6wind.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netlink message header (struct nlmsghdr) is an unused parameter in
fill method of fib_rules_ops struct. This patch removes this
parameter from this method and fixes the places where this method is
called.
(include/net/fib_rules.h)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be sent periodically. The rs_delay can be speficied when adding the
PRL entry and defaults to 15 minutes.
The RS is sent from every link local adress that's assigned to the
tunnel interface. It's directed to the (guessed) linklocal address
of the router and is sent through the tunnel.
Better: send to ff02::2 encapsuled in unicast directed to router-v4.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A tunnel with no local ipv4 endpoint would otherwise use the
ISATAP linklocal address fe80::5efe:0:0, which is invalid. Rather not
add a linklocal address at all.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typo. When deleting a PRL entry, return status to userspace
instead of success.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check link device when looking up a tunnel. When a tunnel is
linked to a interface, traffic from a different interface must not
reach the tunnel.
This also allows creating of multiple tunnels with the same
endpoints, if the link device differs.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When locating the tunnel, do not continue if it is found. Otherwise
a different tunnel with similar configuration would be returned and
parts could be overwritten.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just returning -ERESTARTSYS without a signal pending is not
good that will just leak it to userspace. We need return
-ERESTARTNOINTR so we always restart and set signal pending
so that we fall of the fast path of syscall return and setup
the system call restart.
So use restart_syscall() which does all of this for us.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch fixes issues with dev->dev_addr changing from array to pointer.
Hopefully there are no others.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As packets ending with NEXTHDR_NONE don't have a last extension header,
the check for the length needs to be after the check for NEXTHDR_NONE.
Signed-off-by: Christoph Paasch <christoph.paasch@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The x_tables are organized with a table structure and a per-cpu copies
of the counters and rules. On older kernels there was a reader/writer
lock per table which was a performance bottleneck. In 2.6.30-rc, this
was converted to use RCU and the counters/rules which solved the performance
problems for do_table but made replacing rules much slower because of
the necessary RCU grace period.
This version uses a per-cpu set of spinlocks and counters to allow to
table processing to proceed without the cache thrashing of a global
reader lock and keeps the same performance for table updates.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a brand new GRO skb, we cannot call ip_hdr since the header
may lie in the non-linear area. This patch adds the helper
skb_gro_network_header to handle this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP MIB (RFC 4293) defines stats for InOctets, OutOctets, InMcastOctets and
OutMcastOctets:
http://tools.ietf.org/html/rfc4293
But it seems we don't track those in any way that easy to separate from other
protocols. This patch adds those missing counters to the stats file. Tested
successfully by me
With help from Eric Dumazet.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
last_synq_overflow eats 4 or 8 bytes in struct tcp_sock, even
though it is only used when a listening sockets syn queue
is full.
We can (ab)use rx_opt.ts_recent_stamp to store the same information;
it is not used otherwise as long as a socket is in listen state.
Move linger2 around to avoid splitting struct mtu_probe
across cacheline boundary on 32 bit arches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After switch (rthdr->type) {...},the check below is completely useless.Because:
if the type is 2,then hdrlen must be 2 and segments_left must be 1,clearly the
check is redundant;if the type is not 2,then goto sticky_done,the check is useless
too.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
b44: Use kernel DMA addresses for the kernel DMA API
forcedeth: Fix resume from hibernation regression.
xfrm: fix fragmentation on inter family tunnels
ibm_newemac: Fix dangerous struct assumption
gigaset: documentation update
gigaset: in file ops, check for device disconnect before anything else
bas_gigaset: use tasklet_hi_schedule for timing critical tasklets
net/802/fddi.c: add MODULE_LICENSE
smsc911x: remove unused #include <linux/version.h>
axnet_cs: fix phy_id detection for bogus Asix chip.
bnx2: Use request_firmware()
b44: Fix sizes passed to b44_sync_dma_desc_for_{device,cpu}()
socket: use percpu_add() while updating sockets_in_use
virtio_net: Set the mac config only when VIRITO_NET_F_MAC
myri_sbus: use request_firmware
e1000: fix loss of multicast packets
vxge: should include tcp.h
Conflict in firmware/WHENCE (SCSI vs net firmware)
If an ipv4 packet (not locally generated with IP_DF flag not set) bigger
than mtu size is supposed to go via a xfrm ipv6 tunnel, the packetsize
check in xfrm4_tunnel_check_size() is omited and ipv6 drops the packet
without sending a notice to the original sender of the ipv4 packet.
Another issue is that ipv4 connection tracking does reassembling of
incomming fragmented packets. If such a reassembled packet is supposed to
go via a xfrm ipv6 tunnel it will be droped, even if the original sender
did proper fragmentation.
According to RFC 2473 (section 7) tunnel ipv6 packets resulting from the
encapsulation of an original packet are considered as locally generated
packets. If such a packet passed the checks in xfrm{4,6}_tunnel_check_size()
fragmentation is allowed according to RFC 2473 (section 7.1/7.2).
This patch sets skb->local_df in xfrm6_prepare_output() to achieve
fragmentation in this case.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
Commit 784544739a
(netfilter: iptables: lock free counters) forgot to disable BH
in arpt_do_table(), ipt_do_table() and ip6t_do_table()
Use rcu_read_lock_bh() instead of rcu_read_lock() cures the problem.
Reported-and-bisected-by: Roman Mindalev <r000n@r000n.net>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 778d80be52
(ipv6: Add disable_ipv6 sysctl to disable IPv6 operaion on specific interface)
seems to have introduced a leak of sk_buff's for ipv6 traffic,
at least in some configurations where idev is NULL, or when ipv6
is disabled via sysctl.
The problem is that if the first condition of the if-statement
returns non-NULL, it returns an skb with only one reference,
and when the other conditions apply, execution jumps to the "out"
label, which does not call kfree_skb for it.
To plug this leak, change to use the "drop" label instead.
(this relies on it being ok to call kfree_skb on NULL)
This also allows us to avoid calling rcu_read_unlock here,
and removes the only user of the "out" label.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e1b4b9f ([NETFILTER]: {ip,ip6,arp}_tables: fix exponential worst-case
search for loops) introduced a regression in the loop detection algorithm,
causing sporadic incorrectly detected loops.
When a chain has already been visited during the check, it is treated as
having a standard target containing a RETURN verdict directly at the
beginning in order to not check it again. The real target of the first
rule is then incorrectly treated as STANDARD target and checked not to
contain invalid verdicts.
Fix by making sure the rule does actually contain a standard target.
Based on patch by Francis Dupont <Francis_Dupont@isc.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
We use same not trivial helper function in four places. We can factorize it.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The ipv6 version of bind_conflict code calls ipv6_rcv_saddr_equal()
which at times wrongly identified intersections between addresses.
It particularly broke down under a few instances and caused erroneous
bind conflicts.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Binding to a v4-mapped address on an AF_INET6 socket should
produce the same result as binding to an IPv4 address on
AF_INET socket. The two are interchangable as v4-mapped
address is really a portability aid.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv4 wildcard (0.0.0.0) address does not intersect
in any way with explicit IPv6 addresses. These two should
be permitted, but the IPv4 conflict code checks the ipv6only
bit as part of the test. Since binding to an explicit IPv6
address restricts the socket to only that IPv6 address, the
side-effect is that the socket behaves as v6-only. By
explicitely setting ipv6only in this case, allows the 2 binds
to succeed.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A socket marked v6-only, can not receive or send traffic to v4-mapped
addresses. Thus allowing binding to v4-mapped address on such a
socket makes no sense.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_sack_swap seems unnecessary so I pushed swap to the caller.
Also removed comment that seemed then pointless, and added include
when not already there. Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev can be NULL in ip[6]_frag_reasm for skb's coming from RAW sockets.
Quagga's OSPFD sends fragmented packets on a RAW socket, when netfilter
conntrack reassembles them on the OUTPUT path you hit this code path.
You can test it with something like "hping2 -0 -d 2000 -f AA.BB.CC.DD"
With help from Jarek Poplawski.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the regressions cause by
commit 1326c3d5a4
(v2.6.28-rc6-461-g23a12b1) broke the display of local and remote
addresses of an SIT tunnel in iproute2.
nt->parms is used by ipip6_tunnel_init() and therefore need to be
initialized first.
Tracked as http://bugzilla.kernel.org/show_bug.cgi?id=12868
Reported-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the behavior of allowing both sysctl and addrconf_dad_failure()
to set the disable_ipv6 parameter without any bad side-effects.
If DAD fails and accept_dad > 1, we will still set disable_ipv6=1,
but then instead of allowing an RA to add an address then
immediately fail DAD, we simply don't allow the address to be
added in the first place. This also lets the user set this flag
and disable all IPv6 addresses on the interface, or on the entire
system.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NEXTHDR_NONE doesn't has an IPv6 option header, so the first check
for the length will always fail and results in a confusing message
"too short" if debugging enabled. With this patch, we check for
NEXTHDR_NONE before length sanity checkings are done.
Signed-off-by: Christoph Paasch <christoph.paasch@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The ip6_queue module is missing the net-pf-16-proto-13 alias that would
cause it to be auto-loaded when a socket of that type is opened. This
patch adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch modifies nf_log to use a linked list of loggers for each
protocol. This list of loggers is read and write protected with a
mutex.
This patch separates registration and binding. To be used as
logging module, a module has to register calling nf_log_register()
and to bind to a protocol it has to call nf_log_bind_pf().
This patch also converts the logging modules to the new API. For nfnetlink_log,
it simply switchs call to register functions to call to bind function and
adds a call to nf_log_register() during init. For other modules, it just
remove a const flag from the logger structure and replace it with a
__read_mostly.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Do not try to "uninitialize" ipv6 if its initialization had been skipped
because module parameter disable=1 had been specified.
Reported-by: Thomas Backlund <tmb@mandriva.org>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Acked-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocols that use packet_type can be __read_mostly section for better
locality. Elminate any unnecessary initializations of NULL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add "disable" module parameter support to ipv6.ko by specifying
"disable=1" on module load. We just do the minimum of initializing
inetsw6[] so calls from other modules to inet6_register_protosw()
won't OOPs, then bail out. No IPv6 addresses or sockets can be
created as a result, and a reboot is required to enable IPv6.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a network namespace is destroyed the network interfaces are
all unregistered, making addrconf_ifdown called by the netdevice
notifier.
In the other hand, the addrconf exit method does a loop on the network
devices and does addrconf_ifdown on each of them. But the ordering of
the netns subsystem is not right because it uses the register_pernet_device
instead of register_pernet_subsys. If we handle the loopback as
any network device, we can safely use register_pernet_subsys.
But if we use register_pernet_subsys, the addrconf exit method will do
exactly what was already done with the unregistering of the network
devices. So in definitive, this code is pointless.
I removed the netns addrconf exit method and moved the code to the
addrconf cleanup function.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have a valid net in that place, but this is not just a
cleanup - the tw pointer can be NULL there sometimes, thus causing
an oops in NET_NS=y case.
The same place in ipv4 code already works correctly using existing
net, rather than tw's one.
The bug exists since 2.6.27.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions time_before is more robust for comparing
jiffies against other values.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
@@
- if (E)
- kfree_skb(E);
+ kfree_skb(E);
// </smpl>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the return value of nlmsg_notify() as follows:
If NETLINK_BROADCAST_ERROR is set by any of the listeners and
an error in the delivery happened, return the broadcast error;
else if there are no listeners apart from the socket that
requested a change with the echo flag, return the result of the
unicast notification. Thus, with this patch, the unicast
notification is handled in the same way of a broadcast listener
that has set the NETLINK_BROADCAST_ERROR socket flag.
This patch is useful in case that the caller of nlmsg_notify()
wants to know the result of the delivery of a netlink notification
(including the broadcast delivery) and take any action in case
that the delivery failed. For example, ctnetlink can drop packets
if the event delivery failed to provide reliable logging and
state-synchronization at the cost of dropping packets.
This patch also modifies the rtnetlink code to ignore the return
value of rtnl_notify() in all callers. The function rtnl_notify()
(before this patch) returned the error of the unicast notification
which makes rtnl_set_sk_err() reports errors to all listeners. This
is not of any help since the origin of the change (the socket that
requested the echoing) notices the ENOBUFS error if the notification
fails and should resync itself.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warning:
net/ipv6/xfrm6_state.c:72:26: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reader/writer lock in ip_tables is acquired in the critical path of
processing packets and is one of the reasons just loading iptables can cause
a 20% performance loss. The rwlock serves two functions:
1) it prevents changes to table state (xt_replace) while table is in use.
This is now handled by doing rcu on the xt_table. When table is
replaced, the new table(s) are put in and the old one table(s) are freed
after RCU period.
2) it provides synchronization when accesing the counter values.
This is now handled by swapping in new table_info entries for each cpu
then summing the old values, and putting the result back onto one
cpu. On a busy system it may cause sampling to occur at different
times on each cpu, but no packet/byte counts are lost in the process.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Sucessfully tested on my dual quad core machine too, but iptables only (no ipv6 here)
BTW, my new "tbench 8" result is 2450 MB/s, (it was 2150 MB/s not so long ago)
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
ip6_tables netfilter module can use an ifname_compare() helper
so that two loops are unfolded.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Concern has been expressed about the changing Kconfig options.
Provide the old options that forward-select.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Suggested by: James King <t.james.king@gmail.com>
Similarly to commit c9fd496809, merge
TTL and HL. Since HL does not depend on any IPv6-specific function,
no new module dependencies would arise.
With slight adjustments to the Kconfig help text.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds a logging message for invalid new icmpv6 packet.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Later patches change the locking on xt_table and the initialization of
the lock element is not needed since the lock is always initialized in
xt_table_register anyway.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch fixes a trivial typo that was adding a new line at end of
the nf_log_packet() prefix. It also make the logging conditionnal by
adding a LOG_INVALID test.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
When the user creates IPv6 over IPv6 tunnel, the device name created
by the kernel isn't set to t->parm.name, which is referred as the
result of ioctl().
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes connection tracking handling for ICMPv6 messages
related to Stateless Address Autoconfiguration, MLD, and MLDv2. They
can not be tracked because they are massively using multicast (on
pre-defined address). But they are not invalid and should not be
detected as such.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet