This patch adds two new device ids to the asix driver.
One comes directly from the asix driver on their web site, the other was
reported by Armani Liao as needed for the MSI X320 to get the driver to
work properly for it.
Reported-by: Armani Liao <aliao@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are two paths for filling rx buffer queues. One is
used during initialization and the other during runtime. This patch
removes ql_alloc_sbq_buffers() and ql_alloc_lbq_buffers() and replaces
them with a call to the runtime functions ql_update_lbq() and
ql_update_sbq().
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Buffers are refilled in chunks of 16 at a time before notifying the
hardware with a register write. This can cause several writes to take
place in a given napi poll call. This change causes the write to take place
only once at the end of the call.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of taking/giving the hw semaphore repeatedly when iterating over
several frame to queue route settings, we have the caller hold it until
all are done.
This reduces PCI bus chatter and possible waits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of taking/giving the semaphore repeatedly when iterating over
several adderesses, we have the caller hold it until all are done. This
reduces PCI bus chatter and possible waits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting MAC addresses and routing frames to various queues will need to
be done in response to firmware events as well as during initialization.
This change encapsulates the facilities into a single call that can
later me made from other places.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A receive coalescing timeout of 250 usec appears to strike a good
balance between allowing enough received frames to be aggregated for
LRO to do its job and not allowing the connection to stall due to
delaying ACKs to the remote end for too long.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the netif_carrier_off() call in ->open() to port probe, so that
ethtool doesn't report the link as being up before we have up'd the
interface.
Move initialisation of the rx/tx coalescing timers from ->open() to
port probe, so that we don't reset the coalescing timers every time
the interface is up'd.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split pci probe function into smaller logical blocks.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it was pointed out on the list that ixgbe was failing when using 64kB pages
and large 16kB MTU.
since with a 64kB PAGE_SIZE MAX_SKB_FRAGS = 3, the way the driver was
configuring page usage was assuming 2kB is half a page, and was only
ever dmaing that much data to a half page.
(16kB - header size) / 2048 = 7 or 8 pages, which would far exceed 3
adjust the driver to account for these large pages, the hardware can
support DMA to up to 16kB for each descriptor.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Shannon Nelson <shannon.nelson@intel.com>
The ring_feature member of ixgbe_adapter is statically allocated based on
the supported features of the device. When a new feature is added, we need
to manually update the static allocation. This patch makes the feature
list an enum, eliminating the need for multiple updates to the code when
adding a new feature.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI bar 0 is used for memory mapped register access.
If ioremap fails (returns NULL), register access results
in crash.
Use pci_ioremap_bar() instead of ioremap(), the latter
fails on on 32 bit powerpc where pci resource address is
> 32 bits.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI function to physical port mapping is valid only for
old firmware. New firmware (4.0.0+) abstracts this.
So driver should never try to access phy using invalid
mapping. The behavior is unpredictable when PCI functions
4-7 are enabled on the same NIC.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the KMS case, enter/leavevt won't fix up the interrupt handler for
us, so we need to do it at suspend/resume time. Make sure we don't fail
the resume if the chip is hung either.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dev_priv->hw_status_page can be NULL, if i915_gem_retire_requests()
is called from i915_gem_busy_ioctl().
Signed-off-by Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix double free at netns creation
veth : add the set_mac_address capability
sunlance: Beyond ARRAY_SIZE of ib->btx_ring
sungem: another error printed one too early
ISDN: fix sc/shmem printk format warning
SMSC: timeout reaches -1
smsc9420: handle magic field of ethtool_eeprom
sundance: missing parentheses?
smsc9420: fix another postfixed timeout
wimax/i2400m: driver loads firmware v1.4 instead of v1.3
vlan: Update skb->mac_header in __vlan_put_tag().
cxgb3: Add support for PCI ID 0x35.
tcp: remove obsoleted comment about different passes
TG3: &&/|| confusion
ATM: misplaced parentheses?
net/mv643xx: don't disable the mib timer too early and lock properly
net/mv643xx: use GFP_ATOMIC while atomic
atl1c: Atheros L1C Gigabit Ethernet driver
net: Kill skb_truesize_check(), it only catches false-positives.
net: forcedeth: Fix wake-on-lan regression
Add new USB ID codes. These come from two postings on forums and
mailing lists, and four are derived from the .inf that accompanies
the latest Realtek Windows driver for the RTL8187L.
Thanks to Viktor Ilijašić <viktor.ilijasic@gmail.com> and Xose Vazquez
Perez <xose.vazquez@gmail.com> for reporting these new ID's.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With DEBUG_NOTIFIERS it results in
[11330.890966] WARNING: at /home/bor/src/linux-git/kernel/notifier.c:88
notifier_call_chain+0x91/0xa0()
[11330.890977] Hardware name: PORTEGE 4000
[11330.890983] Invalid notifier called! ...
Without DEBUG_NOTIFIERS it most likely crashes on NULL pointer.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
there might be a nicer way to fix this but this is the simplest for now.
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The object is dereferenced before the NULL check. Oops.
Fixes http://bugs.freedesktop.org/show_bug.cgi?id=20235
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This ensures that the user gets the latest information from the hardware
on whether the buffer is busy, potentially reducing the working set of objects
that the user chooses.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the KMS case, we need to suspend/resume GEM as well. So on suspend, make
sure we idle GEM and stop any new rendering from coming in, and on resume,
re-init the framebuffer and clear the suspended flag.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The problem was that object_set_to_gpu_domain would set the new write_domains
that are getting set by this batchbuffer, then the accumulated flushes required
for all the objects in preparation for this batchbuffer were posted, and the
brand new write domain would get cleared by the flush being posted. Instead,
hang on to the new (or old if we're not changing it) value and set it after
the flush is queued.
Results from this noticably included conformance test failures from reads
shortly after writes (where the new write domain had been lost and thus not
flushed and waited on), but is a suspected cause of hangs in some apps when
a write domain is lost on a buffer that gets reused for instruction or
commmand state.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
While not strictly required, it helped while thinking about the following
change. This change should be invariant.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Impact: module build fix
Fix:
ERROR: "sysdev_resume" [arch/x86/kernel/apm.ko] undefined!
ERROR: "sysdev_suspend" [arch/x86/kernel/apm.ko] undefined!
As these APIs are now used by the APM driver, which can be built
as a module.
Also fix a few extra (and inconsistent) newlines in comment blocks
preceding these functions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the sysdev_suspend/resume from the callee to the callers, with
no real change in semantics, so that we can rework the disabling of
interrupts during suspend/hibernation.
This is based on an earlier patch from Linus.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: remove CONFIG_ACPI_SYSTEM
fujitsu-laptop: Use RFKILL support bitmask from firmware
x86_64: Fix S3 fail path
x86_64: acpi/wakeup_64 cleanup
battery: don't assume we are fully charged when not charging or discharging
ACPI: EC: Add delay for slow MSI controller
http://kisskb.ellerman.id.au/kisskb/buildresult/72115/:
| net/mac80211/ieee80211_i.h:327: error: syntax error before 'volatile'
| net/mac80211/ieee80211_i.h:350: error: syntax error before '}' token
| net/mac80211/ieee80211_i.h:455: error: field 'sta' has incomplete type
| distcc[19430] ERROR: compile net/mac80211/main.c on sprygo/32 failed
This is caused by
| # define mfp ((*(volatile struct MFP*)MFP_BAS))
in arch/m68k/include/asm/atarihw.h, which conflicts with the new "mfp" enum in
net/mac80211/ieee80211_i.h.
Rename "mfp" to "st_mfp", as it's a way too generic name for a global #define.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Further to a71558d, this is round five of fixes to make etherh work
again. As mainline kernels stand, the fixes in b9a9b4b were the wrong
approach.
The 8390 driver was structured by Al Viro to allow the flexibility required
by platforms. lib8390.c contains the core code which drivers explicitly
include:
- 8390.c includes lib8390.c to provide the standard ISA based driver.
- etherh.c includes it with the accessors defined for RiscPC platforms,
where it is addressed via the MMIO accessors with a device dependent
register spacing.
Other platform drivers do something similar.
However, b9a9b4b caused the kernel to contain not only the etherh private
build of lib8390 (included in etherh.c) but also lib8390.c itself, and
referred the new net_device_ops methods to the ISA version. The result
of this is is not pretty:
Unable to handle kernel paging request at virtual address 12032030
pgd = c8330000
[12032030] *pgd=00000000
Internal error: Oops: 18331805 [#1]
Modules linked in: ipv6
CPU: 0 Not tainted (2.6.29-rc3 #167)
PC is at do_set_multicast_list+0xd0/0x190
LR is at bitrev32+0x28/0x34
pc : [<c017aab4>] lr : [<c0139120>] psr: a0000093
sp : c8321d9c ip : c8321d84 fp : c8321dbc
r10: c80c6800 r9 : 00000000 r8 : c80c6b60
r7 : c80c6b80 r6 : cc80c800 r5 : c80c6800 r4 : 00000000
r3 : cc80c80c r2 : 00000004 r1 : 00000007 r0 : e0000000
Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
...
Fix up b9a9b4b by making etherh's net_device_ops refer to the internal
lib8390 functions, and remove the build of the ISA 8390.c driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove CONFIG_ACPI_SYSTEM. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Some things under CONFIG_ACPI_SYSTEM (acpi_irq_handled, acpi_os_gpe_count(),
event_is_open, register_acpi_notifier(), etc.) are used unconditionally
by the CA, the OSPM, and drivers, so we depend on them always being
present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Up until now, we polled the rfkill status for every incoming FUJ02E3 ACPI event.
It turns out that the firmware has a bitmask which indicates what rfkill-related
state it can report.
The rfkill_supported bitmask is now used to avoid polling for rfkill at all in
the notification handler if there is no support. Also, it is used in the platform
device callbacks. As before we register all callbacks and report "unknown" if the
firmware does not give us status updates for that particular bit.
This was fed through checkpatch.pl and tested on the S6420, S7020 and P8010
platforms.
Signed-off-by: Tony Vroon <tony@linx.net>
Tested-by: Stephen Gildea <stepheng+linux@gildea.com>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>
The failure happens when an interrupt occurs and the driver is reading
EICR. This read will cause a clear-by-read which leads to two TLP
being inserted in the PCIe retry buffer leading to an overflow of the
buffer and corruption of TLPs.
The solution is different depending where the reading of EICR takes place.
For ixgbe_msix_lsc() since we are in MSIX mode and know OCD is enabled a
clear-by-write is done instead of the normal clear-by-read.
For ixgbe_intr() 0xffffffff is written to EIMC before the read, masking the
interrupts.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* hibernate:
PM: Fix suspend_console and resume_console to use only one semaphore
PM: Wait for console in resume
PM: Fix pm_notifiers during user mode hibernation
swsusp: clean up shrink_all_zones()
swsusp: dont fiddle with swappiness
PM: fix build for CONFIG_PM unset
PM/hibernate: fix "swap breaks after hibernation failures"
PM/resume: wait for device probing to finish
Consolidate driver_probe_done() loops into one place
there's a few places that currently loop over driver_probe_done(), and
I'm about to add another one. This patch abstracts it into a helper
to reduce duplication.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller