qmi_wwan has been changed to drive both the control and data
interface for all QMI/wwan devices, using cdc-wdm as a subdriver.
Remove the stale device ID entries from cdc-wdm.
>From now on new QMI/wwan devices will only need to be added to
the qmi_wwan driver, regardless of the USB descriptor layout
Note that this is not appropriate for stable/longterm kernels
despite being a device ID patch.
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently CDC-ACM devices stay throttled when their TTY is closed while
throttled, stalling further communication attempts after the next open.
Unthrottling during open/activate got lost starting with kernel
3.0.0 and this patch reintroduces it.
Signed-off-by: Otto Meta <otto.patches@sister-shadow.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hub-initiated LPM is not good for USB communications devices. Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.
If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data. Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.
The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host. In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.
Set the disable_hub_initiated_lpm flag for for all USB communications
drivers. I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Prevents dereferencing an invalid struct usb_interface
pointer.
Always delete entry from device list whether or not the
rest of the device state cleanup is postponed. The device
list uses desc->intf as key, and wdm_open will dereference
this key while searching for a matching device. A device
should not appear in the list unless probe() has succeeded
and disconnect() has not finished.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cannot dereference a removed USB interface for
dev_printk. Use pr_debug instead where necessary.
Flush errors are expected if device is unplugged and are
therefore best ingored at this point.
Move the kill_urbs() call in wdm_release with dev_dbg()
for the non disconnect, as we know it has already been
called if WDM_DISCONNECTING is set. This does not
actually fix anything, but keeps the code more consistent.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Else the poll will be restarted indefinitely in a tight loop,
preventing final device cleanup.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
The internal error codes returned in the write() code
path cannot be simply passed on to user space.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device state cleanup is done in either wdm_disconnect or
wdm_release depending on the order they are called. Adding
a couple of debug messages to document the program flow.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cleanup() is not called if the last close() comes after
disconnect(). That leads to a memory leak. Rectified
by checking for an earlier disconnect() in release()
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wdm_flush() returns unsanitized USB error codes.
They must be cleaned up to before being anded to user space
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a race whereby a pointer to a buffer
would be overwritten while the buffer was in use leading
to a double free and a memory leak. This causes crashes.
This bug was introduced in 2.6.34
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and other
various minor things.
There are some patches touching arch code, but they have all been acked
by the various arch maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9njL8ACgkQMUfUDdst+ylQ9wCfbBOnIT01lGOorkaE9pom0hhk
HfMAoKq1xzCR2B+OS3UMyUQffk+Ri9Ri
=KIQ2
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB merge for 3.4-rc1 from Greg KH:
"Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and
other various minor things.
There are some patches touching arch code, but they have all been
acked by the various arch maintainers."
* tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (302 commits)
net: qmi_wwan: add support for ZTE MF820D
USB: option: add ZTE MF820D
usb: gadget: f_fs: Remove lock is held before freeing checks
USB: option: make interface blacklist work again
usb/ub: deprecate & schedule for removal the "Low Performance USB Block" driver
USB: ohci-pxa27x: add clk_prepare/clk_unprepare calls
USB: use generic platform driver on ath79
USB: EHCI: Add a generic platform device driver
USB: OHCI: Add a generic platform device driver
USB: ftdi_sio: new PID: LUMEL PD12
USB: ftdi_sio: add support for FT-X series devices
USB: serial: mos7840: Fixed MCS7820 device attach problem
usb: Don't make USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.
usb gadget: fix a section mismatch when compiling g_ffs with CONFIG_USB_FUNCTIONFS_ETH
USB: ohci-nxp: Remove i2c_write(), use smbus
USB: ohci-nxp: Support for LPC32xx
USB: ohci-nxp: Rename symbols from pnx4008 to nxp
USB: OHCI-HCD: Rename ohci-pnx4008 to ohci-nxp
usb: gadget: Kconfig: fix typo for 'different'
usb: dwc3: pci: fix another failure path in dwc3_pci_probe()
...
This driver can be used as a subdriver of another USB driver, allowing
it to export a Device Managment interface consisting of a single interrupt
endpoint with no dedicated USB interface.
Some devices provide a Device Management function combined with a wwan
function in a single USB interface having three endpoints (bulk in/out
+ interrupt). If the interrupt endpoint is used exclusively for DM
notifications, then this driver can support that as a subdriver
provided that the wwan driver calls the appropriate entry points on
probe, suspend, resume, pre_reset, post_reset and disconnect.
The main driver must have full control over all interface related
settings, including the needs_remote_wakeup flag. A manage_power
function must be provided by the main driver.
A manage_power stub doing direct flag manipulation is used in normal
driver mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register all interfaces handled by this driver in a list, getting
rid of the dependency on usb_set_intfdata. This allows further
generalization and simplification of the probe/create functions.
This is needed to decouple wdm_open from the driver owning the
interface, and it also allows us to share all the code in
wdm_create with drivers unable to do usb_set_intfdata.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparing for the addition of subdriver registering as an alternative
to probe for interface-less usage. This should not change anything
apart from minor code reordering.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.
pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a piece I missed the last time.
Do not copy the functionality all over the tree. Instead, use the
helper the tty layer provides us with.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had a user report that running setserial on /dev/ttyACM0 didn't work.
He pointed at an old patch by Oliver Neukum from 2008 that never went anywhere..
http://permalink.gmane.org/gmane.linux.usb.general/9236
I made some minor changes to get it to apply again, and got the user to retest on 3.1,
and he reported it worked for him. https://bugzilla.redhat.com/show_bug.cgi?id=787607
The diff below is against 3.3rc. The only difference between this and
the version the user tested is the removal of the if (!ACM_READY) test
Havard removed ACM_READY in 99823f457d
I'm unclear if there's need for a different test in its place.
From: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WDM_READ flag is cleared later iff desc->length is reduced to 0.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We must not allow the input buffer length to change while we're
shuffling the buffer contents. We also mustn't clear the WDM_READ
flag after more data might have arrived. Therefore move both of these
into the spinlocked region at the bottom of wdm_read().
When reading desc->length without holding the iuspin lock, use
ACCESS_ONCE() to ensure the compiler doesn't re-read it with
inconsistent results.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a flag to tell wdm_read/wdm_write that a reset is in progress,
and wake any blocking read/write before taking the mutexes. This
allows the device to reset without waiting for blocking IO to
finish.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is done to resolve a merge conflict with:
drivers/usb/class/cdc-wdm.c
and to better handle future patches for this driver as it is under
active development at the moment.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[v2: Editorial changes suggested by Sergei Shtylyov]
These modems use the Qualcomm MSM Interface (QMI) protocol for
management of their CDC ECM like wwan interface. This driver
is perfect for exporting the protocol to userspace.
The created character device will be indistinguishable from a
common AT command based Device Management interface, so
userspace applications must do some intelligent matching
on the USB device.
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_register_dev() will change our .minor_base to 0 if
CONFIG_USB_DYNAMIC_MINORS is set. And it usually is, of
course.
Use dev_name() to print the proper interface name instead
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The probe does not strictly require the USB_CDC_DMM_TYPE
descriptor, which is a good thing as it makes the driver
usable on non-conforming interfaces. A user could e.g.
bind to it to a CDC ECM interface by using the new_id and
bind sysfs files. But this would fail with a 0 buffer length
due to the missing descriptor.
Fix by defining a reasonable fallback size: The minimum
device receive buffer size required by the CDC WMC standard,
revision 1.1
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The probe does not strictly require the USB_CDC_DMM_TYPE
descriptor, which is a good thing as it makes the driver
usable on non-conforming interfaces. A user could e.g.
bind to it to a CDC ECM interface by using the new_id and
bind sysfs files. But this would fail with a 0 buffer length
due to the missing descriptor.
Fix by defining a reasonable fallback size: The minimum
device receive buffer size required by the CDC WMC standard,
revision 1.1
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need bMaxPacketSize0, and keeping all these different size fields
around will only cause us to use the wrong one.
Seems the udev variable was only used for getting bMaxPacketSize0. We
could have used it for the usb_fill_*_urb() calls, but as it wasn't
before - why start now? Instead make the interface_to_usbdev()
calls consistent.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Documentation/usb/dma.txt states:
Most drivers should *NOT* be using these primitives; they don't need
to use this type of memory (dma-coherent), and memory returned from
kmalloc() will work just fine.
This driver handle only very low bandwith transfers. It is not an
obvious candidate for usb_alloc_coherent().
Using these calls only serves to complicate the code for no gain,
as has been shown by multiple bugs related to this allocation path.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As it turns out, there was a mismatch between the allocated inbuf size
(desc->bMaxPacketSize0, typically something like 64) and the length we
specified in the URB (desc->wMaxCommand, typically something like 2048)
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Filling the same URB with the exact same data is pointless. It can be filled
once and resubmitted. And not doing buffer allocation and URB filling at the
same place only serves to hide size mismatch bugs
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As it turns out, there was a mismatch between the allocated inbuf size
(desc->bMaxPacketSize0, typically something like 64) and the length we
specified in the URB (desc->wMaxCommand, typically something like 2048)
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
wdm_disconnect() waits for the mutex held by wdm_read() before
calling wake_up_all(). This causes a deadlock, preventing device removal
to complete. Do the wake_up_all() before we start waiting for the locks.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
using a separate read and write mutex for locking is sufficient to make the
driver accept simultaneous read and write. This improves useability a lot.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
wdm_in_callback() will also touch this field, so we cannot change it without locking
Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some failures, the country_code field of an acm structure is freed
without freeing the acm structure itself. Elsewhere, operations including
memcpy and kfree are performed on the country_code field. The patch sets
the country_code field to NULL when it is freed, and likewise sets the
country_code_size field to 0.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
both callers of device_get_devnode() are only interested in lower 16bits
and nobody tries to return anything wider than 16bit anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add USB IDs for Motorola H24 HSPA USB module.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ACM_READY() macro doesn't seem to do anything useful, and it may
prevent tty_wait_until_sent() from working properly when called from
close.
Previously, acm_tty_chars_in_buffer() returned 0 whenever
acm->port.count was 0. This means close() could return before all the
data has actually been written.
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the locking and lifecycle management in the cdc-acm driver.
Instead of using a global mutex to prevent the 'acm' object from being
freed, use the tty_port kref to keep the device alive when either the
USB side or TTY side is still active.
This allows us to use the global mutex purely for protecting the
acm_table, while use acm->mutex to guard against disconnect during
TTY port activation and shutdown.
The USB-side kref is taken during port initialization in probe(), and
released at the end of disconnect(). The TTY-side kref is taken in
install() and released in cleanup(). On disconnect, tty_vhangup() is
called instead of tty_hangup() to ensure the TTY hangup processing is
completed before the USB device is taken down.
The TTY open and close handlers have been gutted and replaced with
tty_port_open() and tty_port_close() respectively. The driver-specific
code which used to be there was spread across install(), activate() and
shutdown().
Reported-by: Dave Jones <davej@redhat.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the drivers in drivers/usb/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Simon Arlott <cxacru@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Cc: Cesar Miquel <miquel@df.uba.ar>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Michael Hund <mhund@ld-didactic.de>
Cc: Zack Parsons <k3bacon@gmail.com>
Cc: Melchior FRANZ <mfranz@aon.at>
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a race between the USB disconnect handler and the TTY close
handler which may cause the acm object to be freed while it's still
being used. This may lead to things like
http://article.gmane.org/gmane.linux.usb.general/54250
and
https://lkml.org/lkml/2011/5/29/64
This is the simplest fix I could come up with. Holding on to open_mutex
while closing the TTY device prevents acm_disconnect() from freeing the
acm object between acm->port.count drops to 0 and the TTY side of the
cleanups are finalized.
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size
instead of le16_to_cpu(desc->wMaxPacketSize).
This patch fix it up
Cc: Armin Fuerst <fuerst@in.tum.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Erdfelt <johannes@erdfelt.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: David Kubicek <dave@awk.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Brad Hards <bhards@bigpond.net.au>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: David Lopo <dlopo@chipidea.mips.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Xie Xiaobo <X.Xie@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Jiang Bo <tanya.jiang@freescale.com>
Cc: Yuan-hsin Chen <yhchen@faraday-tech.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Roman Weissgaerber <weissg@vienna.at>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Florian Floe Echtler <echtler@fs.tum.de>
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Juergen Stuber <starblue@sourceforge.net>
Cc: Georges Toth <g.toth@e-biz.lu>
Cc: Bill Ryder <bryder@sgi.com>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1482) adds a macro for testing whether or not a
pm_message value represents an autosuspend or autoresume (i.e., a
runtime PM) event. Encapsulating this notion seems preferable to
open-coding the test all over the place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Assign operator instead of equality test in the usbtmc_ioctl_abort_bulk_in() function.
Signed-off-by: Maxim A. Nikulin <M.A.Nikulin@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited()
Signed-off-by: Manuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the Nokia E7 and C7 to the list of devices in cdc-acm, allowing
the secondary ACM channel on the device to be exposed. Without this patch
the ACM driver won't claim this secondary channel as it's marked as
having a vendor-specific protocol.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Droids MuIn LCD operates like a serial remote terminal.
Data received are displayed directly on the LCD. This patch
fixes the kernel null pointer oops when it is plugged in.
Add NO_DATA_INTERFACE quirk to tell the driver that "control"
and "data" interfaces are not separated for this device, which
prevents dereferencing a null pointer in the device probe code.
Signed-off-by: Erik Slagter <erik@slagter.name>
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Tested-by: Erik Slagter <erik@slagter.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch
- ensures no IO takes place during resets
- reports resets to user space
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill rx tasklet, which is no longer needed, and re-write read processing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allocate read urbs and read buffers in the same loop during probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No need to kill ctrl urb on errors as this is done later during close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The drain-delay code is no longer used, so remove it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove driver version and changelog which can be retrieved from git
history.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace dev_dbg with verbose dev_vdbg in read/write paths where
appropriate.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace all remaining instances of dbg with dev_dbg.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up some dev_err and dev_dbg messages and make sure that the
appropriate interface device is used for reporting consistently
throughout.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add missing newline to two dev_dbg and dev_err messages.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix potential null-pointer exception on disconnect introduced by commit
11ea859d64 (USB: additional power savings
for cdc-acm devices that support remote wakeup).
Only access acm->dev after making sure it is non-null in control urb
completion handler.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Must check return value of tty_port_tty_get.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the WDM class driver a disconnect event leads to calls to
usb_free_coherent to put back two USB DMA buffers allocated earlier.
The call to usb_free_coherent uses a different size parameter
(desc->wMaxCommand) than the corresponding call to usb_alloc_coherent
(desc->bMaxPacketSize0).
When a disconnect event occurs, this leads to 'bad dma' complaints
from usb core because the USB DMA buffer is being pushed back to the
'buffer-2048' pool from which it has not been allocated.
This patch against the most recent linux-2.6 kernel ensures that the
parameters used by usb_alloc_coherent & usb_free_coherent calls in
cdc-wdm.c match.
Signed-off-by: Robert Lukassen <robert.lukassen@tomtom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only oddities here are a couple of drivers that bogusly called the ldisc
helpers instead of returning -ENOIOCTLCMD. Fix the bug and the rest goes
away.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the N8 to the list of devices in cdc-acm, in order to get the
secondary ACM device exposed.
In the spirit of:
http://kerneltrap.org/mailarchive/linux-usb/2010/9/4/6264554
Signed-off-by: Arvid Ephraim Picciani <arvid.picciani@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Certain USB devices, such as the Nokia X6 mobile phone, don't expose any
endpoint descriptors on some of their interfaces. If the ACM driver is forced
to probe all interfaces on a device the a NULL pointer dereference will occur
when the ACM driver attempts to use the endpoint of the alternative settings.
One way to get the ACM driver to probe all the interfaces is by using the
/sys/bus/usb/drivers/cdc_acm/new_id interface.
This patch checks that the endpoint pointer for the current alternate settings
is non-NULL before using it.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm.c : Manage pseudo-modem without AT commands capabilities
Enable to drive electronic simple gadgets based on microcontrolers.
The Interface descriptor is like this:
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0 None
Signed-off-by: Philippe Corbes <philippe.corbes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
S60 phones from Nokia and Samsung expose two ACM channels. The first is a modem
with a standard AT-command interface, which is picked up correctly by CDC-ACM.
The second ACM port is marked as having a vendor-specific protocol. This means
that the ACM driver will not claim the second channel by default.
This adds support for the second ACM channel for the following devices:
Nokia E63
Nokia E75
Nokia 6760 Slide
Nokia E52
Nokia E55
Nokia E72
Nokia X6
Nokia N97 Mini
Nokia 5800 Xpressmusic
Nokia E90
Samsung GTi8510 (INNOV8)
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wait_event_interruptible_timeout in acm_port_down is
never reached. Remove it to avoid possible deadlocks
with the big tty mutex if someone were to start using
the blocking version of acm_port_down.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nokia S60 phones expose two ACM channels. The first is
a modem, the second is 'vendor-specific' but is treated
as a serial device at the S60 end, so we want to expose
it on Linux too.
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pavel@suse.cz no longer works, replace it with working address.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes resource reclaim in error path of acm_probe:
1. In the case of "out of memory (read urbs usb_alloc_urb)\n")", there
is no need to call acm_read_buffers_free(acm) here. Fix it by goto
alloc_fail6 instead of alloc_fail7.
2. In the case of "out of memory (write urbs usb_alloc_urb)",
usb_alloc_urb may fail in any iteration of the for loop. Current
implementation does not properly free allocated snd->urb. Fix it by
goto alloc_fail8 instead of alloc_fail7.
3. In the case of device_create_file(&intf->dev,&dev_attr_iCountryCodeRelDate)
fail, acm->country_codes is kfreed. As a result, device_remove_file
for dev_attr_wCountryCodes will not be executed in acm_disconnect.
Fix it by calling device_remove_file for dev_attr_wCountryCodes
before goto skip_countries.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Maretron USB100 needs this quirk in order to work properly.
Signed-off-by: Russ Nelson <nelson@crynwr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The new runtime PM scheme allows resume() to have no locks.
This fixes the deadlock.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- as the callback can schedule work, URBs must be killed first
- if the driver causes an autoresume, the caller must handle locking
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The guarding flag must be set and tested under spinlock
and cleared before the URBs are resubmitted in resume.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a window under which cdc-wdm may submit
an URB to a device about to be suspended. This
introduces a flag to prevent it.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dev_dbg() and dev_err() cannot be used to report failures
that may have been caused by a device's removal
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While an available response is read the device must not
be autosuspended. This requires a flag dedicated to that
purpose.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unify mutexes to fix a race between write and disconnect
and shift the test for disconnection to always report it.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The lock must be dropped before usb_autopm_interface_put() is called
Signed-off-by: Oliver Neukum <oliver@neukum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Under the new system a device cannot be suspended against
the driver's wish. Therefore this condition no longer needs
to be checked for.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pbLua console port is known to not be a modem, so it is
unnecessary to be told this when it is plugged in.
Add NOT_A_MODEM quirk to tell the driver that we know this already
and hence not to warn us, and mark the pbLua console port.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pbLua firmware (http://pblua.com/) for the Lego Mindstorms NXT
provides a CDC ACM port for it's serial console.
This used to be detected automatically, but this support has been
dropped, probably for sensible reasons.
Explicitly add support for this device by adding an item to the
device ID table.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update cdc-acm to the async methods eliminating the workqueue
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the USB Test & Measurement driver use usb_clear_halt() instead of
usb_control_msg() to clear a stalled endpoint. This will allow devices to
be tested under an xHCI host controller. The endpoint stall will not be
cleared in the internal xHCI hardware state unless usb_clear_halt() is
used.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Steve Holland <sdh4@iastate.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_bulk_msg() transfers only bytes up to the maximum packet size.
It must be repeated by the usbtmc driver until all bytes of a TMC message
are transfered.
Without this patch, ETIMEDOUT is reported when writing TMC messages
larger than the maximum USB bulk size and the transfer remains incomplete.
The user will notice that the device hangs and must be reset by either closing
the application or pulling the plug.
Signed-off-by: Andre Herms <andre.herms@tec-venture.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nokia S60 phones expose two ACM channels. The first is a modem and is picked
up by the standard AT-command interface information in the CDC-ACM driver. The
second is marked as having a vendor-specific protocol. Normally, we don't
expose those as ttys. (On some other devices, they may be claimed by the
rndis_host driver and used as a network interface).
But on S60 this second ACM channel is the way that third-party S60 application
developers are expected to communicate over USB. It acts as a serial device
at the S60 end, and so it should on Linux too.
The list of devices is largely derived from:
http://wiki.forum.nokia.com/index.php/S60_Platform_and_device_identification_codeshttp://wiki.forum.nokia.com/index.php/Nokia_USB_Product_IDs
and includes only the S60 3rd Edition+ devices documented there.
There are many devices for which the USB device ID is not documented,
including:
Nokia 6290
Nokia E63
Nokia 5630 XpressMusic
Nokia 5730 XpressMusic
Nokia 6710 Navigator
Nokia 6720 classic
Nokia 6730 Classic
Nokia 6760 slide
Nokia 6790 slide
Nokia 6790 Surge
Nokia E52
Nokia E55
Nokia E71x (AT&T)
Nokia E72
Nokia E75
Nokia E75 US+LTA variant
Nokia N79
Nokia N86 8MP
Nokia 5230 (RM-588)
Nokia 5230 (RM-594)
Nokia 5530 XpressMusic
Nokia 5530 XpressMusic (china)
Nokia 5800 XM
Nokia N97 (RM-506)
Nokia N97 mini
Nokia X6
It would be good to add those subsequently.
Signed-off-by: Adrian Taylor <aat@realvnc.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Donnerstag, 10. September 2009 15:43:53 schrieb Dietmar Hilbrich:
> Hello,
>
> i have the following problem with the cdc-acm - driver:
>
> I'm using the driver with an "Ericsson F3507G" on a Thinkpad T400.
>
> If a disable the device (with the RFKill-Switch) while it is used by a
> programm like ppp, the driver doesn't seem to correctly clean up the tty,
> even after the program has been closed)
>
> The tty is still active (e.g. there still exists an entry in
> /sys/dev/char/166:0 if ttyACM0 was used) and if a reacticate the device,
> this device entry will be skipped and the Device-Nodes ttyACM1, ttyACM2
> and ttyACM3 will be used.
>
> This problem was introduced with the commit
> 10077d4a66 (before 2.6.31-rc1) and still
> exists in 2.6.31.
>
> I was able the fix this problem with the following patch:
>
> diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
> index 2bfc41e..0970d2f 100644
> --- a/drivers/usb/class/cdc-acm.c
> +++ b/drivers/usb/class/cdc-acm.c
> @@ -676,6 +676,7 @@ static void acm_tty_hangup(struct tty_struct *tty)
> struct acm *acm = tty->driver_data;
> tty_port_hangup(&acm->port);
> acm_port_down(acm, 0);
> + acm_tty_unregister(acm);
> }
I have the same problem with cdc-acm (I'm using a Samsung SGH-U900): when I
unplug it from the USB port during a PPP connection, the ppp daemon gets the
hangup correctly (and closes the device), but the struct acm corresponding to
the device disconnected is not freed. Hence reconnecting the device results in
creation of /dev/ttyACM(x+1). The same happens when the system is hibernated
during a PPP connection.
This memory leak is due to the fact that when the tty is hung up,
tty_port_close_start() returns always zero, and acm_tty_close() never reaches
the point where acm_tty_unregister() is called.
Here is a fix for this.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If acm_rx_tasklet() gets called before tty_port_block_til_ready()
returns, then bulk IN urbs may not be sent. This fixes it.
Signed-off-by: Henry Gebhardt <gebhardt@astro.uni-tuebingen.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current 10ms timeout is too short for some normal USBTMC device
operation, increase it to a value which was tested with previously
affected Tektronix oscilloscopes.
Signed-off-by: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order:
Add reference to relevant section of USBTMC usb488 subclass specs.
Print debug output of capabilities only when it was retrieved successfully.
Clear return value on success, otherwise driver always reports failure.
Signed-off-by: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Limit data copied to userspace to amount requested. Prevents a faulty
instrument from overwriting user memory.
Signed-off-by: Steve Holland <sdh4@iastate.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The header size should not be included in the number of bytes requested of the
instrument
Signed-off-by: Steve Holland <sdh4@iastate.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix printk format warnings:
drivers/usb/class/usbtmc.c:466: warning: format '%zu' expects type 'size_t', but argument 4 has type 'u32'
drivers/usb/class/usbtmc.c:466: warning: format '%zu' expects type 'size_t', but argument 5 has type 'int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the specifications, an instrument should not return more data in a
DEV_DEP_MSG_IN urb than requested. However, some instruments can send more
than requested. This could cause the kernel to write the extra data past the
end of the buffer provided by read().
Fix this by checking that the value of the TranserSize field is not larger than
the urb itself and not larger than the size of the userspace buffer. Also
correctly decrement the remaining size of the buffer when userspace read()s
more than USBTMC_SIZE_IOBUFFER.
Signed-off-by: Guus Sliepen <guus@sliepen.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
a class driver should have suspend/resume. This makes sure we
don't see a virtual disconnect unnecessarily.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbtmc will happily complete read/write requests even after disconnect
has returned. The fix is to introduce a flag.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm needs to set a flag during open to tell the
tty layer that the device is initialized
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Paul Martin <pm@debian.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
support for O_NONBLOCK in read and write path
by simply not waiting for data in read or availability
of the write urb in write but returning -EAGAIN
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changed in 2006 so its about time the ACM driver caught up
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes an oops caused when during an unplug a device's table
of endpoints is zeroed before the driver is notified. A pointer to
the endpoint must be cached.
this fixes a regression caused by commit
5186ffee23
Therefore it should go into 2.6.31
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function does not have an error return and returning an error is
instead interpreted as having a lot of pending bytes.
Reported by Jeff Harris who provided a list of some of the remaining
offenders.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces a work around for cdc-acm devices which are
low speed contrary to the specification, which requires bulk endpoints
which are banned in low speed and converted by usbcore to virtual
interrupt endpoints if they are used nevertheless.
Signed-off-by: Arseniy Lartsev <ars3n@yandex.ru>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit 10077d4a66 has stopped
checking if there was a valid acm device associated to the tty, which is
not true right after open fails and tty subsystem tries to close the
device.
As an example, open fails with a non-existing device, when probe has
never been called, because the device has never been plugged. This is
common in systems with static modules and no udev.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is required, otherwise a user will get a EINVAL while opening a
non-existing device, instead of ENODEV.
This is what I get with this patch applied now instead of an "Invalid
argument".
cascardo@vespa:~$ cat /dev/ttyACM0
cat: /dev/ttyACM0: No such device
cascardo@vespa:~$
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steve Holland pointed out that we forgot to call break; in the switch
statment. This probably resolves a lot of the bug reports I've gotten
for the driver lately.
Stupid me...
Reported-by: Steve Holland <sdh4@iastate.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This mobile phone fails to work as a modem, failing with:
cdc_acm: Zero length descriptor references
cdc_acm: probe of 1-6.1.3:1.1 failed with error -22
Tested to work fine with this patch.
Signed-off-by: Kir Kolyshkin <kir@openvz.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This implement support in cdc-acm for acm devices another popular OS can handle
- adds support for autodetection of devices that use one interface
- autodetection of endpoints
- add a quirk for surpressing a setting that OS doesn't use
- autoassume that quirk for single interface devices
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for USB drivers to report their requested nodename to
userspace. It also updates a number of USB drivers to provide the
needed subdirectory and device name to be used for them.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Or at least most of it. There are further clean ups possible and there are
are also thing checkpatch moans about that would be silly to "fix".
Also note some FIXME points found as the cleanup was done.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now we have a port structure begin using the fields and kref counts
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CDC ACM driver uses the tty layer correctly so needs conversion. Start by
adding and initializing the port structures.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds another quirky Conexant USB Modem Clone to usb cdc-acm.c
Signed-off-by: Xiao Kaijian <xiaokj@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch to cdc-wdm
- checks for partial extra descriptors
- fixes a leak in the error case of probe
- checks for an exact number of endpoints
- adds a clarifying comment
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ACM sets the low latency flag but calls the flip buffer routines from
IRQ context which isn't permitted (and as of 2.6.29 causes a warning
hence this one was caught)
Fortunatelt ACM doesn't need to set this flag in the first place as it
only set it to work around problems in ancient (pre tty flip rewrite)
kernels.
Reported-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bugzilla #9095 and a couple of other confirmations
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The cdc_acm module is missing the char-major-166-* alias that would
cause it to be auto-loaded when a device of that type is opened. This
patch adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The usblp in 2.6.18 polled for status regardless if we actually needed it.
At some point I dropped it, to save the batteries if nothing else.
As it turned out, printers exist (e.g. Canon BJC-3000) that need prodding
this way or else they stop. This patch restores the old behaviour.
If you want to save battery, don't leave jobs in the print queue.
I tested this on my printers by printing and examining usbmon traces
to make sure status is being requested and printers continue to print.
Tuomas Jäntti verified the fix on BJC-3000.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver already supports the 1 protocol support, so just add it to
the MODULE_DEVICE_TABLE entry so it properly picks up these devices.
Thanks to Jouni Rynö for pointing this out.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
open() will never succeed, as we always return -ENODEV. Fix this
obvious bug.
Thanks to Jouni Ryno for reporting it.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the cdc-acm driver can
properly handle this combined device.
Signed-off-by: Dmitriy Taychenachev <dimichxp@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The same patch to add support for MTK gps loggers was submitted by two
different people and applied twice. Remove the redundant lines.
Signed-off-by: James Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another Conexant, another device with the same quirk
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?
output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):
before patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error)
after patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0
Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.
I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: Andrew Lunn, <andrew@lunn.ch>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.
From: James A. Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1177) modifies the USB core suspend and resume
routines. The resume functions now will take a pm_message_t argument,
so they will know what sort of resume is occurring. The new argument
is also passed to the port suspend/resume and bus suspend/resume
routines (although they don't use it for anything but debugging).
In addition, special pm_message_t values are used for user-initiated,
device-initiated (i.e., remote wakeup), and automatic suspend/resume.
By testing these values, drivers can tell whether or not a particular
suspend was an autosuspend. Unfortunately, they can't do the same for
resumes -- not until the pm_message_t argument is also passed to the
drivers' resume methods. That will require a bigger change.
IMO, the whole Power Management framework should have been set up this
way in the first place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It seems that there's rather involved way to say something
which is commonly written in a plain simple form.
Some type changes would probably be necessary to get gcc
to do bitops instead of divide but it's no worse after my
change than before I think.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbtmc driver forgot to export its device table to userspace.
Without this, it is never loaded properly when such a device is seen by
the system.
Cc: Marcel Janssen <marcel.janssen@admesy.nl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Silences compiler warning about comparison with 0x80, and type now matches the
corresponding _bulk_out function.
drivers/usb/class/usbtmc.c: In function ‘usbtmc_ioctl_abort_bulk_in’:
drivers/usb/class/usbtmc.c:163: warning: comparison is always false due to limited range of data type
Signed-off-by: Chris Malley <mail@chrismalley.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a memory leak on disconnect in cdc-acm
Thanks to 施金前 for finding it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this fixes an omission that led to no alias being computed for the
cdc-wdm module.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove err() and
use the system-wide standard of dev_err() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible. In the
few places that will not work out, use a basic printk().
Clean up the remaining usages of this in the drivers/usb/ directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In this code, it is possible to tell statically whether usblp will be NULL
in the error handling code.
Oliver Neukum suggested to make a goto to the final return rather than
return directly.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
identifier f,err,l,l1;
type T;
expression x,E;
statement S;
@@
x = NULL
... when != goto l1;
* x = f(...)
... when != x
err = E;
goto l;
...
* if (x != NULL)
S
return err;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver was originaly written by Stefan Kopp, but massively
reworked by Greg for submission.
Thanks to Felipe Balbi <me@felipebalbi.com> for lots of work in cleaning
up this driver.
Thanks to Oliver Neukum <oliver@neukum.org> for reviewing previous
versions and pointing out problems.
Cc: Stefan Kopp <stefan_kopp@agilent.com>
Cc: Marcel Janssen <korgull@home.nl>
Cc: Felipe Balbi <me@felipebalbi.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch gets my Rosewill RNX-56USB USB modem (with Conexant CX93010
chipset) up and running to the point where I can send AT commands and
retrieve caller ID data, which is all I want to do with it.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a mechanism to let the write queue drain naturally before
closing the TTY, rather than always losing that data. There
is a timeout, so it can't wait too long.
Provide missing locking inside acm_wb_is_avail(); it matters
more now. Note, this presumes an earlier patch was applied,
removing a call to this routine where the lock was held.
Slightly improved diagnostics on write URB completion, so we
can tell when a write URB gets killed and, if so, how much
data it wrote first ... and so that I/O path is normally
silent (and can't much change timings).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "increase cdc-acm write throughput" patch left in place two
now-obsolete mechanisms, either of which can make the cdc-acm
driver drop TX data (nasty!). This patch removes them:
- The write_ready flag ... if an URB and buffer were found,
they can (and should!) always be used.
- TX path acm_wb_is_used() ... used when the buffer was just
allocated, so that check is pointless.
Also fix a won't-yet-matter leak of a write buffer on a disconnect path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Engraf <david.engraf@netcom.eu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bugfixes to the usb_driver_release_interface() usage;
(a) make sure releasing *either* interface first will release
the other, instead of insisting it be the control interface;
(b) remove the recently-added self-deadlock.
(The "fix disconnect bug in cdc-acm" patch was incomplete and incorrect.)
Plus a small "sparse" fix: rename a local variable so it doesn't
shadow a function parameter.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The irq flags should be unsigned long.
CC [M] drivers/usb/class/cdc-acm.o
drivers/usb/class/cdc-acm.c: In function 'acm_waker':
drivers/usb/class/cdc-acm.c:527: warning: comparison of distinct pointer types lacks a cast
drivers/usb/class/cdc-acm.c:529: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some hardware needs to do break handling itself and may have partial
support only. Make break_ctl return an error code. Add a tty driver flag
so you can indicate driver hardware side break support.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the fix. cdc-wdm has the same problem. The fix is the same.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm must give up secondary interfaces if the primary is disconnected
and vice versa. This wasn't done correctly.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch saves power for cdc-acm devices that support remote wakeup
while the device is connected.
- request needs_remote_wakeup when needed
- delayed write while a device is autoresumed
- the device is marked busy when appropriate
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- fixes an error with filling out control requests
- increases grepability and error logging
- fixes the short read code path
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm has
- a memory leak in resume()
- will fail to reactivate the read code path if this is needed.
his corrects it by deleting the useless relict code.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* wMaxPacketSize is le16; copying it to a field of local structure and then
using that field as host-endian (size of object to be allocated) is broken.
* bMaxPacketSize0 is 8-bit; feeding it to le16_to_cpu() is bogus and since the
result is used as host-endian, it's not even misspelled cpu_to_le16().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch below is a necessary workaround to support the Zoom Telephonics Model 3095F V.92 USB Mini External modem, which fails to initialise properly during normal probing thus:
May 3 22:53:00 imcfarla kernel: drivers/usb/class/cdc-acm.c: Zero length descriptor references
May 3 22:53:00 imcfarla kernel: cdc_acm: probe of 5-2:1.0 failed with error -22
Adding the patch below causes the probing section to be skipped, and the modem
then initialises correctly.
Signed-off-by: Iain McFarlane <iain@imcfarla.homelinux.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix bogus assignment of "unsigned char *" to "char *": preserve
unsignedness. These values are used directly as descriptor lengths
when iterating through the buffer, so this *could* cause oddness
that potentially includes oopsing. (IMO not likely, except as
part of a malicious device...)
Fix the bogus warning in CDC ACM which highlighted this problem
(by showing a negative descriptor type). It uses the undesirable
legacy err() for something that's not even an error; switch to
use dev_dbg, and show descriptor types in hex notation to match
the convention for such codes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the following patch uses 16 write urbs and a writsize of wMaxPacketSize
* 20. With this patch I get the maximum througput from my linux system
with 20MB/sec read and 15 MB/sec write (full speed 1 MB/sec both)
I also deleted the flag URB_NO_FSBR for the writeurbs, because this
makes my full speed devices significant slower.
Signed-off-by: David Engraf <david.engraf@netcom.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It ensures that the tty level do not split
the send buffer into 2KB blocks.
Signed-off-by: David Engraf <david.engraf@netcom.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this fixes a race between open and disconnect in the CDC ACM driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if you fail in open() you must decrement the pm counter again.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Here we go. This patch implements suspend/resume and autosuspend
for the CDC ACM driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If submit fails, slab hits a BUG() because of a double kfree.
The today's lesson is, you cannot just slap USB_FREE_BUFFER on code
without adjusting the error paths.
The patch is made bigger by opportunistic refactoring.
Signed-Off-By: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a small bunch of cosmetic fixes:
- Timeout is not a write timeout anymore, rename
- Condition in poll was confusingly backwards, invert and simplify
- The comment log gave a wrong impression of version 0.13, terminate it.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a mutex to protect the ->statusbuf. Not really an issue, because CUPS
is single-threaded when it talks to the printer, but I feel safer this way.
This should be deadlock-free, but I kept this as a separate patch in case
someone ends running a git bisect.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Employ the new API URB_FREE_BUFFER that we've got. There was talk of a combined
constructor for this case, but apparently it's not happening, so just set the
flag explicitly for now.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements a mode when a printer returns ENOSPC when it runs
out of paper. The default remains the same as before. An application which
wishes to use this function has to enable it explicitly with an ioctl
LPABORT.
This is done on a request by our (Fedora) CUPS guy, Tim Waugh. The API is
similar enough to the lp0's one that CUPS works with both (but see below),
but it's has some differences.
Most importantly, the abort mode is persistent in case of lp0: once tunelp
was run your cat fill blow up until you reboot or run tunelp again. For
usblp, I made it so the abort mode is only in effect as long as device
is open. This way you can mix and match CUPS and cat(1) freely and nothing
bad happens even if you run out of paper. It is also safer in the face
of any unexpected crashes.
It has to be noted that mixing LPABORT and O_NONBLOCK is not advised.
It probably does not do what you want: instead of returning -ENOSPC
it will always return -EAGAIN (because it would otherwise block while
waiting for the paper). Applications which use O_NONBLOCK should continue
to use LPGETSTATUS like before.
Finally, CUPS actually requires patching to take full advantage of this.
It has several components; those which invoke LPABORT work, but some of
them need the ioctl added. This is completely compatible, you can mix
old CUPS and new kernels or vice versa.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as950) fixes a bug in the cdc-acm driver. It doesn't keep
track of which interface (control or data) the sysfs attributes get
registered for, and as a result, during disconnect it will sometimes
attempt to remove the attributes from the wrong interface. The
left-over attributes can cause a crash later on, particularly if the driver
module has been unloaded.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found the first regresson in the rewritten ("all dynamic" and "no races")
driver. If application uses O_NONBLOCK, I return -EAGAIN despite the URB
being submitted successfuly. This causes the application to resubmit the
same data erroneously.
The fix is to pretend that the transfer has succeeded even if URB was
merely queued. It is the same behaviour as with the old version.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: add new device id to option driver
device is Samsung X180 China cellphone
Signed-off-by: Andrey Arapov <andrey.arapov@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch's main bulk aims to make usblp the premier driver for code
pillaging once again. The code is as streamlined as possible and is bug-free
as possible. The usb-skeleton performs the same function, but is somewhat
abstract. The usblp is usb-skeleton which is actually used by many.
Since I combed a few small bugs away, this also fixes the small races we
had in usblp for a while. For example, now it's possible for several threads
to make write(2) calls (sounds silly, but consider a printer for paper
record, where every line of text is self-contained and thus it's all right
to have them interleaved). Also gone are issues with interrupts using
barriers dangerously.
This patch makes use of Oliver's anchor, and so it must trail the anchor
patch on the way to Linus.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like the error path had a copy-paste error. The normal exit path
uses correct URB already.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
this patch exports the attributes cdc-acm knows about a device through sysfs.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as872) adds a device table entry and a new quirk flag to
the usblp driver for the Seiko Epson Receipt printer. This printer
returns Vendor-Specific values for bInterfaceClass and
bInterfaceSubClass, but the bInterfaceProtocol value is valid and it
works with usblp. The new quirks flag tells the driver to ignore the
Class and SubClass values in the interface descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this fixes the spinlock recursion issue. The older fix was incomplete.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is Joris' fixes reshuffelled and features renamed as David requested.
- acm_set_control is not mandatory, honour that
- throtteling is reset upon open
- throtteling is read consistently when processing input data
Signed-off-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this implements autosuspend for usb printers. It compiles and is tested.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch gets the Kyocera FS-820 working with cups 1.2 via usb again. It
adds the printer to the list of "quirky" printers. The printer seems not
answer to ID requests some seconds after plugging in. Patch is based on
linux-2.6.19.1.
Background:
As far as I could see (strace, usbmon), the Kyocera FS-820 answers to ID
requests only a few seconds after plugging it in. This applies to detecting
it with cups and is also true for the printing itself, which is initiated
with an ID request. Since I have little usb knowledge, maybe someone can
interpret the data, especially the fist bulk transfer - why request 8192
bytes? This is the second version of the patch.
usbmon output of printing an email without patch:
tail -F /tmp/printlog.txt
c636e140 3374734463 S Bi:002:02 -115 8192 <
c9d43b40 3374734494 S Ci:002:00 s a1 00 0000 0000 03ff 1023 <
c9d43b40 3379732301 C Ci:002:00 -104 0
c636e140 3379733294 C Bi:002:02 -2 0
[...repeating...]
with patch:
tail -F /tmp/printlog.txt
d9cb82c0 3729790131 S Ci:002:00 s a1 00 0000 0000 03ff 1023 <
d9cb82c0 3729791725 C Ci:002:00 0 91 = 005b4944 3a46532d 3832303b 4d46473a
4b796f63 6572613b 434d443a 50434c58 df956320 3732493190 S Bo:002:01 -115
1347 = 1b252d31 32333435 5840504a 4c0a4050 4a4c2053 4554204d 414e5541
4c464545 [...more data...]
Signed-off-by: Martin Williges <kernel@zut.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch:
- converts usblp fully to mutex
- makes sleeping interruptible where EINTR can be returned anyway
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
this has been confirmed to fix suspend problems with usblp.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if urb submission fails due to a transient error here eg. ENOMEM
, the driver is dead. This fixes it.
Regards
Oliver
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this implements suspend support for usblp. According to the CUPS people
ENODEV will make CUPS retry the job. Thus it is returned in the runtime
case. My printer survives suspend/resume cycles with it.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below is a necessary workaround to support the BT On-Air USB modem, which
fails to initialise properly during normal probing thus:
Sep 30 17:34:57 sled kernel: drivers/usb/class/cdc-acm.c: Zero length descriptor references
Sep 30 17:34:57 sled kernel: cdc_acm: probe of 1-1.2:1.0 failed with error -22
Adding the patch below causes the probing section to be skipped, and the modem
then initialises correctly.
Signed-off-by: Chris Malley <mail@chrismalley.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
As part of an SMP cleanliness pass over UML, I consted a bunch of
structures in order to not have to document their locking. One of these
structures was a struct tty_operations. In order to const it in UML
without introducing compiler complaints, the declaration of
tty_set_operations needs to be changed, and then all of its callers need to
be fixed.
This patch declares all struct tty_operations in the tree as const. In all
cases, they are static and used only as input to tty_set_operations. As an
extra check, I ran an i386 allyesconfig build which produced no extra
warnings.
53 drivers are affected. I checked the history of a bunch of them, and in
most cases, there have been only a handful of maintenance changes in the
last six months. serial_core.c was the busiest one that I looked at.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Making structs const prevents accidental bugs and with the proper debug
options they're protected against corruption.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this adds
better debugging output &
an update of the quirk list
to the acm driver
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've always found this flag confusing. Now that devfs is no longer around, it
has been renamed, and the documentation for when this flag should be used has
been updated.
Also fixes all drivers that use this flag.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bjørn Mork