The ioeventfd here is actually irqfd handling of an ioeventfd such as
supported in KVM. A user is able to pre-program a device write to
occur when the eventfd triggers. This is yet another instance of
eventfd-irqfd triggering between KVM and vfio. The impetus for this
is high frequency writes to pages which are virtualized in QEMU.
Enabling this near-direct write path for selected registers within
the virtualized page can improve performance and reduce overhead.
Specifically this is initially targeted at NVIDIA graphics cards where
the driver issues a write to an MMIO register within a virtualized
region in order to allow the MSI interrupt to re-trigger.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This reverts commit 2170dd0431
The intent of commit 2170dd0431 ("vfio-pci: Mask INTx if a device is
not capabable of enabling it") was to disallow the user from seeing
that the device supports INTx if the platform is incapable of enabling
it. The detection of this case however incorrectly includes devices
which natively do not support INTx, such as SR-IOV VFs, and further
discussions reveal gaps even for the target use case.
Reported-by: Arjun Vynipadath <arjun@chelsio.com>
Fixes: 2170dd0431 ("vfio-pci: Mask INTx if a device is not capabable of enabling it")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
By default VFIO disables mapping of MSIX BAR to the userspace as
the userspace may program it in a way allowing spurious interrupts;
instead the userspace uses the VFIO_DEVICE_SET_IRQS ioctl.
In order to eliminate guessing from the userspace about what is
mmapable, VFIO also advertises a sparse list of regions allowed to mmap.
This works fine as long as the system page size equals to the MSIX
alignment requirement which is 4KB. However with a bigger page size
the existing code prohibits mapping non-MSIX parts of a page with MSIX
structures so these parts have to be emulated via slow reads/writes on
a VFIO device fd. If these emulated bits are accessed often, this has
serious impact on performance.
This allows mmap of the entire BAR containing MSIX vector table.
This removes the sparse capability for PCI devices as it becomes useless.
As the userspace needs to know for sure whether mmapping of the MSIX
vector containing data can succeed, this adds a new capability -
VFIO_REGION_INFO_CAP_MSIX_MAPPABLE - which explicitly tells the userspace
that the entire BAR can be mmapped.
This does not touch the MSIX mangling in the BAR read/write handlers as
we are doing this just to enable direct access to non MSIX registers.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw - fixup whitespace, trim function name]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The vfio_info_add_capability() helper requires the caller to pass a
capability ID, which it then uses to fill in header fields, assuming
hard coded versions. This makes for an awkward and rigid interface.
The only thing we want this helper to do is allocate sufficient
space in the caps buffer and chain this capability into the list.
Reduce it to that simple task.
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
At the moment VFIO rightfully assumes that INTx is supported if
the interrupt pin is not set to zero in the device config space.
However if that is not the case (the pin is not zero but pdev->irq is),
vfio_intx_enable() fails.
In order to prevent the userspace from trying to enable INTx when we know
that it cannot work, let's mask the PCI_INTERRUPT_PIN register.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Device lock bites again; if a device .remove() callback races a user
calling ioctl(VFIO_GROUP_GET_DEVICE_FD), the unbind request will hold
the device lock, but the user ioctl may have already taken a vfio_device
reference. In the case of a PCI device, the initial open will attempt
to reset the device, which again attempts to get the device lock,
resulting in deadlock. Use the trylock PCI reset interface and return
error on the open path if reset fails due to lock contention.
Link: https://lkml.org/lkml/2017/7/25/381
Reported-by: Wen Congyang <wencongyang2@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
XXV710 has the same broken INTx behavior as the rest of the X/XL710
series, the interrupt status register is not wired to report pending
INTx interrupts, thus we never associate the interrupt to the device.
Extend the device IDs to include these so that we hide that the
device supports INTx at all to the user.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Here, pci_iomap can fail, handle this case release selected
pci regions and return -ENOMEM.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Update msix_sparse_mmap_cap() to use vfio_info_add_capability()
Update region type capability to use vfio_info_add_capability()
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Neo Jia <cjia@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The VFIO_DEVICE_SET_IRQS ioctl did not sufficiently sanitize
user-supplied integers, potentially allowing memory corruption. This
patch adds appropriate integer overflow checks, checks the range bounds
for VFIO_IRQ_SET_DATA_NONE, and also verifies that only single element
in the VFIO_IRQ_SET_DATA_TYPE_MASK bitmask is set.
VFIO_IRQ_SET_ACTION_TYPE_MASK is already correctly checked later in
vfio_pci_set_irqs_ioctl().
Furthermore, a kzalloc is changed to a kcalloc because the use of a
kzalloc with an integer multiplication allowed an integer overflow
condition to be reached without this patch. kcalloc checks for overflow
and should prevent a similar occurrence.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Current vfio-pci implementation disallows to mmap
sub-page(size < PAGE_SIZE) MMIO BARs because these BARs' mmio
page may be shared with other BARs. This will cause some
performance issues when we passthrough a PCI device with
this kind of BARs. Guest will be not able to handle the mmio
accesses to the BARs which leads to mmio emulations in host.
However, not all sub-page BARs will share page with other BARs.
We should allow to mmap the sub-page MMIO BARs which we can
make sure will not share page with other BARs.
This patch adds support for this case. And we try to add a
dummy resource to reserve the remainder of the page which
hot-add device's BAR might be assigned into. But it's not
necessary to handle the case when the BAR is not page aligned.
Because we can't expect the BAR will be assigned into the same
location in a page in guest when we passthrough the BAR. And
it's hard to access this BAR in userspace because we have
no way to get the BAR's location in a page.
Signed-off-by: Yongji Xie <xyjxie@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
INTx masking has two components, the first is that we need the ability
to prevent the device from continuing to assert INTx. This is
provided via the DisINTx bit in the command register and is the only
thing we can really probe for when testing if INTx masking is
supported. The second component is that the device needs to indicate
if INTx is asserted via the interrupt status bit in the device status
register. With these two features we can generically determine if one
of the devices we own is asserting INTx, signal the user, and mask the
interrupt while the user services the device.
Generally if one or both of these components is broken we resort to
APIC level interrupt masking, which requires an exclusive interrupt
since we have no way to determine the source of the interrupt in a
shared configuration. This often makes it difficult or impossible to
configure the system for userspace use of the device, for an interrupt
mode that the user may not need.
One possible configuration of broken INTx masking is that the DisINTx
support is fully functional, but the interrupt status bit never
signals interrupt assertion. In this case we do have the ability to
prevent the device from asserting INTx, but lack the ability to
identify the interrupt source. For this case we can simply pretend
that the device lacks INTx support entirely, keeping DisINTx set on
the physical device, virtualizing this bit for the user, and
virtualizing the interrupt pin register to indicate no INTx support.
We already support virtualization of the DisINTx bit and already
virtualize the interrupt pin for platforms without INTx support. By
tying these components together, setting DisINTx on open and reset,
and identifying devices broken in this particular way, we can provide
support for them w/o the handicap of APIC level INTx masking.
Intel i40e (XL710/X710) 10/20/40GbE NICs have been identified as being
broken in this specific way. We leave the vfio-pci.nointxmask option
as a mechanism to bypass this support, enabling INTx on the device
with all the requirements of APIC level masking.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Various enablers for assignment of Intel graphics devices and future
support of vGPU devices (Alex Williamson). This includes
- Handling the vfio type1 interface as an API rather than a specific
implementation, allowing multiple type1 providers.
- Capability chains, similar to PCI device capabilities, that allow
extending ioctls. Extensions here include device specific regions
and sparse mmap descriptions. The former is used to expose non-PCI
regions for IGD, including the OpRegion (particularly the Video
BIOS Table), and read only PCI config access to the host and LPC
bridge as drivers often depend on identifying those devices.
Sparse mmaps here are used to describe the MSIx vector table,
which vfio has always protected from mmap, but never had an API to
explicitly define that protection. In future vGPU support this is
expected to allow the description of PCI BARs that may mix direct
access and emulated access within a single region.
- The ability to expose the shadow ROM as an option ROM as IGD use
cases may rely on the ROM even though the physical device does not
make use of a PCI option ROM BAR.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=/lJn
-----END PGP SIGNATURE-----
Merge tag 'vfio-v4.6-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
"Various enablers for assignment of Intel graphics devices and future
support of vGPU devices (Alex Williamson). This includes
- Handling the vfio type1 interface as an API rather than a specific
implementation, allowing multiple type1 providers.
- Capability chains, similar to PCI device capabilities, that allow
extending ioctls. Extensions here include device specific regions
and sparse mmap descriptions. The former is used to expose non-PCI
regions for IGD, including the OpRegion (particularly the Video
BIOS Table), and read only PCI config access to the host and LPC
bridge as drivers often depend on identifying those devices.
Sparse mmaps here are used to describe the MSIx vector table, which
vfio has always protected from mmap, but never had an API to
explicitly define that protection. In future vGPU support this is
expected to allow the description of PCI BARs that may mix direct
access and emulated access within a single region.
- The ability to expose the shadow ROM as an option ROM as IGD use
cases may rely on the ROM even though the physical device does not
make use of a PCI option ROM BAR"
* tag 'vfio-v4.6-rc1' of git://github.com/awilliam/linux-vfio:
vfio/pci: return -EFAULT if copy_to_user fails
vfio/pci: Expose shadow ROM as PCI option ROM
vfio/pci: Intel IGD host and LCP bridge config space access
vfio/pci: Intel IGD OpRegion support
vfio/pci: Enable virtual register in PCI config space
vfio/pci: Add infrastructure for additional device specific regions
vfio: Define device specific region type capability
vfio/pci: Include sparse mmap capability for MSI-X table regions
vfio: Define sparse mmap capability for regions
vfio: Add capability chain helpers
vfio: Define capability chains
vfio: If an IOMMU backend fails, keep looking
vfio/pci: Fix unsigned comparison overflow
Calling return copy_to_user(...) in an ioctl will not
do the right thing if there's a pagefault:
copy_to_user returns the number of bytes not copied
in this case.
Fix up vfio to do
return copy_to_user(...)) ?
-EFAULT : 0;
everywhere.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The copy_to_user() function returns the number of bytes that were not
copied but we want to return -EFAULT on error here.
Fixes: 188ad9d6cb ('vfio/pci: Include sparse mmap capability for MSI-X table regions')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Integrated graphics may have their ROM shadowed at 0xc0000 rather than
implement a PCI option ROM. Make this ROM appear to the user using
the ROM BAR.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Provide read-only access to PCI config space of the PCI host bridge
and LPC bridge through device specific regions. This may be used to
configure a VM with matching register contents to satisfy driver
requirements. Providing this through the vfio file descriptor removes
an additional userspace requirement for access through pci-sysfs and
removes the CAP_SYS_ADMIN requirement that doesn't appear to apply to
the specific devices we're accessing.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is the first consumer of vfio device specific resource support,
providing read-only access to the OpRegion for Intel graphics devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add support for additional regions with indexes started after the
already defined fixed regions. Device specific code can register
these regions with the new vfio_pci_register_dev_region() function.
The ops structure per region currently only includes read/write
access and a release function, allowing automatic cleanup when the
device is closed. mmap support is only missing here because it's
not needed by the first user queued for this support.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vfio-pci has never allowed the user to directly mmap the MSI-X vector
table, but we've always relied on implicit knowledge of the user that
they cannot do this. Now that we have capability chains that we can
expose in the region info ioctl and a sparse mmap capability that
represents the sub-areas within the region that can be mmap'd, we can
make the mmap constraints more explicit.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
There is really no way to safely give a user full access to a DMA
capable device without an IOMMU to protect the host system. There is
also no way to provide DMA translation, for use cases such as device
assignment to virtual machines. However, there are still those users
that want userspace drivers even under those conditions. The UIO
driver exists for this use case, but does not provide the degree of
device access and programming that VFIO has. In an effort to avoid
code duplication, this introduces a No-IOMMU mode for VFIO.
This mode requires building VFIO with CONFIG_VFIO_NOIOMMU and enabling
the "enable_unsafe_noiommu_mode" option on the vfio driver. This
should make it very clear that this mode is not safe. Additionally,
CAP_SYS_RAWIO privileges are necessary to work with groups and
containers using this mode. Groups making use of this support are
named /dev/vfio/noiommu-$GROUP and can only make use of the special
VFIO_NOIOMMU_IOMMU for the container. Use of this mode, specifically
binding a device without a native IOMMU group to a VFIO bus driver
will taint the kernel and should therefore not be considered
supported. This patch includes no-iommu support for the vfio-pci bus
driver only.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Revert commit 033291eccb ("vfio: Include No-IOMMU mode") due to lack
of a user. This was originally intended to fill a need for the DPDK
driver, but uptake has been slow so rather than support an unproven
kernel interface revert it and revisit when userspace catches up.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
There is really no way to safely give a user full access to a DMA
capable device without an IOMMU to protect the host system. There is
also no way to provide DMA translation, for use cases such as device
assignment to virtual machines. However, there are still those users
that want userspace drivers even under those conditions. The UIO
driver exists for this use case, but does not provide the degree of
device access and programming that VFIO has. In an effort to avoid
code duplication, this introduces a No-IOMMU mode for VFIO.
This mode requires building VFIO with CONFIG_VFIO_NOIOMMU and enabling
the "enable_unsafe_noiommu_mode" option on the vfio driver. This
should make it very clear that this mode is not safe. Additionally,
CAP_SYS_RAWIO privileges are necessary to work with groups and
containers using this mode. Groups making use of this support are
named /dev/vfio/noiommu-$GROUP and can only make use of the special
VFIO_NOIOMMU_IOMMU for the container. Use of this mode, specifically
binding a device without a native IOMMU group to a VFIO bus driver
will taint the kernel and should therefore not be considered
supported. This patch includes no-iommu support for the vfio-pci bus
driver only.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Testing the driver for a PCI device is racy, it can be all but
complete in the release path and still report the driver as ours.
Therefore we can't trust drvdata to be valid. This race can sometimes
be seen when one port of a multifunction device is being unbound from
the vfio-pci driver while another function is being released by the
user and attempting a bus reset. The device in the remove path is
found as a dependent device for the bus reset of the release path
device, the driver is still set to vfio-pci, but the drvdata has
already been cleared, resulting in a null pointer dereference.
To resolve this, fix vfio_device_get_from_dev() to not take the
dev_get_drvdata() shortcut and instead traverse through the
iommu_group, vfio_group, vfio_device path to get a reference we
can trust. Once we have that reference, we know the device isn't
in transition and we can test to make sure the driver is still what
we expect, so that we don't interfere with devices we don't own.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Log some clues indicating whether the user is receiving device
request interfaces or not listening. This can help indicate why a
driver unbind is blocked or explain why QEMU automatically unplugged
a device from the VM.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We can save some power by putting devices that are bound to vfio-pci
but not in use by the user in the D3hot power state. Devices get
woken into D0 when opened by the user. Resets return the device to
D0, so we need to re-apply the low power state after a bus reset.
It's tempting to try to use D3cold, but we have no reason to inhibit
hotplug of idle devices and we might get into a loop of having the
device disappear before we have a chance to try to use it.
A new module parameter allows this feature to be disabled if there are
devices that misbehave as a result of this change.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
As indicated in the comment, this is not entirely uncommon and
causes user concern for no reason.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This copies the same support from pci-stub for exactly the same
purpose, enabling a set of PCI IDs to be automatically added to the
driver's dynamic ID table at module load time. The code here is
pretty simple and both vfio-pci and pci-stub are fairly unique in
being meta drivers, capable of attaching to any device, so there's no
attempt made to generalize the code into pci-core.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If VFIO VGA access is disabled for the user, either by CONFIG option
or module parameter, we can often opt-out of VGA arbitration. We can
do this when PCI bridge control of VGA routing is possible. This
means that we must have a parent bridge and there must only be a
single VGA device below that bridge. Fortunately this is the typical
case for discrete GPUs.
Doing this allows us to minimize the impact of additional GPUs, in
terms of VGA arbitration, when they are only used via vfio-pci for
non-VGA applications.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add a module option so that we don't require a CONFIG change and
kernel rebuild to disable VGA support. Not only can VGA support be
troublesome in itself, but by disabling it we can reduce the impact
to host devices by doing a VGA arbitration opt-out.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Now we have finally completely decoupled virqfd from VFIO_PCI. We can
initialize it from the VFIO generic code, in order to safely use it from
multiple independent VFIO bus drivers.
Signed-off-by: Antonios Motakis <a.motakis@virtualopensystems.com>
Signed-off-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The functions vfio_pci_virqfd_init and vfio_pci_virqfd_exit are not really
PCI specific, since we plan to reuse the virqfd code with more VFIO drivers
in addition to VFIO_PCI.
Signed-off-by: Antonios Motakis <a.motakis@virtualopensystems.com>
[Baptiste Reynal: Move rename vfio_pci_virqfd_init and vfio_pci_virqfd_exit
from "vfio: add a vfio_ prefix to virqfd_enable and virqfd_disable and export"]
Signed-off-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Userspace can opt to receive a device request notification,
indicating that the device should be released. This is setup
the same way as the error IRQ and also supports eventfd signaling.
Future support may forcefully remove the device from the user if
the request is ignored.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Current vfio-pci just supports normal pci device, so vfio_pci_probe() will
return if the pci device is not a normal device. While current code makes a
mistake. PCI_HEADER_TYPE is the offset in configuration space of the device
type, but we use this value to mask the type value.
This patch fixs this by do the check directly on the pci_dev->hdr_type.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org # v3.6+
add Kconfig switch to hide INTx
add Kconfig switch to let vfio announce PCI BARs are not mapable
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Locking both the remove() and release() path results in a deadlock
that should have been obvious. To fix this we can get and hold the
vfio_device reference as we evaluate whether to do a bus/slot reset.
This will automatically block any remove() calls, allowing us to
remove the explict lock. Fixes 61d792562b.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org [3.17]
The existing vfio_pci_open() fails upon error returned from
vfio_spapr_pci_eeh_open(), which breaks POWER7's P5IOC2 PHB
support which this patch brings back.
The patch fixes the issue by dropping the return value of
vfio_spapr_pci_eeh_open().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Each time a device is released, mark whether a local reset was
successful or whether a bus/slot reset is needed. If a reset is
needed and all of the affected devices are bound to vfio-pci and
unused, allow the reset. This is most useful when the userspace
driver is killed and releases all the devices in an unclean state,
such as when a QEMU VM quits.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Serializing open/release allows us to fix a refcnt error if we fail
to enable the device and lets us prevent devices from being unbound
or opened, giving us an opportunity to do bus resets on release. No
restriction added to serialize binding devices to vfio-pci while the
mutex is held though.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Our current open/release path looks like this:
vfio_pci_open
vfio_pci_enable
pci_enable_device
pci_save_state
pci_store_saved_state
vfio_pci_release
vfio_pci_disable
pci_disable_device
pci_restore_state
pci_enable_device() doesn't modify PCI_COMMAND_MASTER, so if a device
comes to us with it enabled, it persists through the open and gets
stored as part of the device saved state. We then restore that saved
state when released, which can allow the device to attempt to continue
to do DMA. When the group is disconnected from the domain, this will
get caught by the IOMMU, but if there are other devices in the group,
the device may continue running and interfere with the user. Even in
the former case, IOMMUs don't necessarily behave well and a stream of
blocked DMA can result in unpleasant behavior on the host.
Explicitly disable Bus Master as we're enabling the device and
slightly re-work release to make sure that pci_disable_device() is
the last thing that touches the device.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The patch adds new IOCTL commands for sPAPR VFIO container device
to support EEH functionality for PCI devices, which have been passed
through from host to somebody else via VFIO.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexander Graf <agraf@suse.de>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
According PCI local bus specification, the register of Message
Control for MSI (offset: 2, length: 2) has bit#0 to enable or
disable MSI logic and it shouldn't be part contributing to the
calculation of MSI interrupt count. The patch fixes the issue.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
There's nothing we can do different if pci_load_and_free_saved_state()
fails, other than maybe print some log message, but the actual re-load
of the state is an unnecessary step here since we've only just saved
it. We can cleanup a coverity warning and eliminate the unnecessary
step by freeing the state ourselves.
Detected by Coverity: CID 753101
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
- Remove unnecessary and dangerous use of device_lock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t9+R
-----END PGP SIGNATURE-----
Merge tag 'vfio-v3.14-rc1' of git://github.com/awilliam/linux-vfio
Pull vfio update from Alex Williamson:
- convert to misc driver to support module auto loading
- remove unnecessary and dangerous use of device_lock
* tag 'vfio-v3.14-rc1' of git://github.com/awilliam/linux-vfio:
vfio-pci: Don't use device_lock around AER interrupt setup
vfio: Convert control interface to misc driver
misc: Reserve minor for VFIO
PCI resets will attempt to take the device_lock for any device to be
reset. This is a problem if that lock is already held, for instance
in the device remove path. It's not sufficient to simply kill the
user process or skip the reset if called after .remove as a race could
result in the same deadlock. Instead, we handle all resets as "best
effort" using the PCI "try" reset interfaces. This prevents the user
from being able to induce a deadlock by triggering a reset.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
device_lock is much too prone to lockups. For instance if we have a
pending .remove then device_lock is already held. If userspace
attempts to modify AER signaling after that point, a deadlock occurs.
eventfd setup/teardown is already protected in vfio with the igate
mutex. AER is not a high performance interrupt, so we can also use
the same mutex to protect signaling versus setup races.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Linus Torvalds